diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
22 files changed, 389 insertions, 12 deletions
diff --git a/Documentation/devicetree/bindings/arm/armada-38x.txt b/Documentation/devicetree/bindings/arm/armada-38x.txt index 11f2330a655..ad9f8ed4d9b 100644 --- a/Documentation/devicetree/bindings/arm/armada-38x.txt +++ b/Documentation/devicetree/bindings/arm/armada-38x.txt @@ -6,5 +6,15 @@ following property: Required root node property: - - compatible: must contain either "marvell,armada380" or - "marvell,armada385" depending on the variant of the SoC being used. + - compatible: must contain "marvell,armada380" + +In addition, boards using the Marvell Armada 385 SoC shall have the +following property before the previous one: + +Required root node property: + +compatible: must contain "marvell,armada385" + +Example: + +compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada380"; diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 5216b419016..8b4f7b7fe88 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -9,6 +9,18 @@ Required Properties: - reg: physical base address of the controller and length of memory mapped region. +Optional Properties: +- clocks: List of clock handles. The parent clocks of the input clocks to the + devices in this power domain are set to oscclk before power gating + and restored back after powering on a domain. This is required for + all domains which are powered on and off and not required for unused + domains. +- clock-names: The following clocks can be specified: + - oscclk: Oscillator clock. + - pclkN, clkN: Pairs of parent of input clock and input clock to the + devices in this power domain. Maximum of 4 pairs (N = 0 to 3) + are supported currently. + Node of a device using power domains must have a samsung,power-domain property defined with a phandle to respective power domain. @@ -19,6 +31,14 @@ Example: reg = <0x10023C00 0x10>; }; + mfc_pd: power-domain@10044060 { + compatible = "samsung,exynos4210-pd"; + reg = <0x10044060 0x20>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_SW_ACLK333>, + <&clock CLK_MOUT_USER_ACLK333>; + clock-names = "oscclk", "pclk0", "clk0"; + }; + Example of the node using power domain: node { diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index b513cb8196f..af527ee111c 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -40,6 +40,9 @@ Optional properties: - arm,filter-ranges : <start length> Starting address and length of window to filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. +- arm,io-coherent : indicates that the system is operating in an hardware + I/O coherent mode. Valid only when the arm,pl310-cache compatible + string is used. - interrupts : 1 combined interrupt. - cache-id-part: cache id part number to be used if it is not present on hardware diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt index 5d49f2b37f6..832fe8cc24d 100644 --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt @@ -48,7 +48,7 @@ adc@12D10000 { /* NTC thermistor is a hwmon device */ ncp15wb473@0 { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <47000>; pulldown-ohm = <0>; diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt index f055515d2b6..366690cb86a 100644 --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt @@ -8,10 +8,12 @@ Both required and optional properties listed below must be defined under node /cpus/cpu@0. Required properties: -- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt - for details +- None Optional properties: +- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt for + details. OPPs *must* be supplied either via DT, i.e. this property, or + populated at runtime. - clock-latency: Specify the possible maximum transition latency for clock, in unit of nanoseconds. - voltage-tolerance: Specify the CPU voltage tolerance in percentage. diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt index c6f66674f19..b117b2e9e1a 100644 --- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -3,11 +3,19 @@ NTC Thermistor hwmon sensors Requires node properties: - "compatible" value : one of - "ntc,ncp15wb473" - "ntc,ncp18wb473" - "ntc,ncp21wb473" - "ntc,ncp03wb473" - "ntc,ncp15wl333" + "murata,ncp15wb473" + "murata,ncp18wb473" + "murata,ncp21wb473" + "murata,ncp03wb473" + "murata,ncp15wl333" + +/* Usage of vendor name "ntc" is deprecated */ +<DEPRECATED> "ntc,ncp15wb473" +<DEPRECATED> "ntc,ncp18wb473" +<DEPRECATED> "ntc,ncp21wb473" +<DEPRECATED> "ntc,ncp03wb473" +<DEPRECATED> "ntc,ncp15wl333" + - "pullup-uv" Pull up voltage in micro volts - "pullup-ohm" Pull up resistor value in ohms - "pulldown-ohm" Pull down resistor value in ohms @@ -21,7 +29,7 @@ Read more about iio bindings at Example: ncp15wb473@0 { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <47000>; pulldown-ohm = <0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt new file mode 100644 index 00000000000..dde6c22ce91 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -0,0 +1,42 @@ +* Rockchip RK3xxx I2C controller + +This driver interfaces with the native I2C controller present in Rockchip +RK3xxx SoCs. + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c" or + "rockchip,rk3288-i2c". + - interrupts : interrupt number + - clocks : parent clock + +Required on RK3066, RK3188 : + + - rockchip,grf : the phandle of the syscon node for the general register + file (GRF) + - on those SoCs an alias with the correct I2C bus ID (bit offset in the GRF) + is also required. + +Optional properties : + + - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used. + +Example: + +aliases { + i2c0 = &i2c0; +} + +i2c0: i2c@2002d000 { + compatible = "rockchip,rk3188-i2c"; + reg = <0x2002d000 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + rockchip,grf = <&grf>; + + clock-names = "i2c"; + clocks = <&cru PCLK_I2C0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt new file mode 100644 index 00000000000..6b765485af7 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt @@ -0,0 +1,41 @@ + +* Allwinner P2WI (Push/Pull 2 Wire Interface) controller + +Required properties : + + - reg : Offset and length of the register set for the device. + - compatible : Should one of the following: + - "allwinner,sun6i-a31-p2wi" + - interrupts : The interrupt line connected to the P2WI peripheral. + - clocks : The gate clk connected to the P2WI peripheral. + - resets : The reset line connected to the P2WI peripheral. + +Optional properties : + + - clock-frequency : Desired P2WI bus clock frequency in Hz. If not set the +default frequency is 100kHz + +A P2WI may contain one child node encoding a P2WI slave device. + +Slave device properties: + Required properties: + - reg : the I2C slave address used during the initialization + process to switch from I2C to P2WI mode + +Example: + + p2wi@01f03400 { + compatible = "allwinner,sun6i-a31-p2wi"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <6000000>; + resets = <&apb0_rst 3>; + + axp221: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + + /* ... */ + }; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 64fd7dec1bb..b3556609a06 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -4,6 +4,13 @@ Required properties: - compatible: Must contain one of the following: + - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. + - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. + - "renesas,scifa-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFA compatible UART. + - "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART. + - "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART. + - "renesas,scifb-r8a7740" for R8A7740 (R-Mobile A1) SCIFB compatible UART. + - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. diff --git a/Documentation/devicetree/bindings/sound/ak5386.txt b/Documentation/devicetree/bindings/sound/ak5386.txt index dc3914fe6ce..ec3df3abba0 100644 --- a/Documentation/devicetree/bindings/sound/ak5386.txt +++ b/Documentation/devicetree/bindings/sound/ak5386.txt @@ -10,10 +10,14 @@ Optional properties: - reset-gpio : a GPIO spec for the reset/power down pin. If specified, it will be deasserted at probe time. + - va-supply : a regulator spec, providing 5.0V + - vd-supply : a regulator spec, providing 3.3V Example: spdif: ak5386@0 { compatible = "asahi-kasei,ak5386"; reset-gpio = <&gpio0 23>; + va-supply = <&vdd_5v0_reg>; + vd-supply = <&vdd_3v3_reg>; }; diff --git a/Documentation/devicetree/bindings/sound/cs4265.txt b/Documentation/devicetree/bindings/sound/cs4265.txt new file mode 100644 index 00000000000..380fff8e4e8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4265.txt @@ -0,0 +1,29 @@ +CS4265 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "cirrus,cs4265" + + - reg : the I2C address of the device for I2C. The I2C address depends on + the state of the AD0 pin. If AD0 is high, the i2c address is 0x4f. + If it is low, the i2c address is 0x4e. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + +Examples: + +codec_ad0_high: cs4265@4f { /* AD0 Pin is high */ + compatible = "cirrus,cs4265"; + reg = <0x4f>; +}; + + +codec_ad0_low: cs4265@4e { /* AD0 Pin is low */ + compatible = "cirrus,cs4265"; + reg = <0x4e>; +}; diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt new file mode 100644 index 00000000000..b93362a570b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -0,0 +1,60 @@ +Freescale Asynchronous Sample Rate Converter (ASRC) Controller + +The Asynchronous Sample Rate Converter (ASRC) converts the sampling rate of a +signal associated with an input clock into a signal associated with a different +output clock. The driver currently works as a Front End of DPCM with other Back +Ends Audio controller such as ESAI, SSI and SAI. It has three pairs to support +three substreams within totally 10 channels. + +Required properties: + + - compatible : Contains "fsl,imx35-asrc" or "fsl,imx53-asrc". + + - reg : Offset and length of the register set for the device. + + - interrupts : Contains the spdif interrupt. + + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. + + - dma-names : Contains "rxa", "rxb", "rxc", "txa", "txb" and "txc". + + - clocks : Contains an entry for each entry in clock-names. + + - clock-names : Contains the following entries + "mem" Peripheral access clock to access registers. + "ipg" Peripheral clock to driver module. + "asrck_<0-f>" Clock sources for input and output clock. + + - big-endian : If this property is absent, the little endian mode + will be in use as default. Otherwise, the big endian + mode will be in use for all the device registers. + + - fsl,asrc-rate : Defines a mutual sample rate used by DPCM Back Ends. + + - fsl,asrc-width : Defines a mutual sample width used by DPCM Back Ends. + +Example: + +asrc: asrc@02034000 { + compatible = "fsl,imx53-asrc"; + reg = <0x02034000 0x4000>; + interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 107>, <&clks 107>, <&clks 0>, + <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, + <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, + <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, + <&clks 107>, <&clks 0>, <&clks 0>; + clock-names = "mem", "ipg", "asrck0", + "asrck_1", "asrck_2", "asrck_3", "asrck_4", + "asrck_5", "asrck_6", "asrck_7", "asrck_8", + "asrck_9", "asrck_a", "asrck_b", "asrck_c", + "asrck_d", "asrck_e", "asrck_f"; + dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, <&sdma 19 23 1>, + <&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>; + dma-names = "rxa", "rxb", "rxc", + "txa", "txb", "txc"; + fsl,asrc-rate = <48000>; + fsl,asrc-width = <16>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/sound/max98090.txt b/Documentation/devicetree/bindings/sound/max98090.txt index a5e63fa47dc..c454e67f54b 100644 --- a/Documentation/devicetree/bindings/sound/max98090.txt +++ b/Documentation/devicetree/bindings/sound/max98090.txt @@ -4,7 +4,7 @@ This device supports I2C only. Required properties: -- compatible : "maxim,max98090". +- compatible : "maxim,max98090" or "maxim,max98091". - reg : The I2C address of the device. diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 8346cab046c..aa697abf337 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -13,6 +13,9 @@ Required properties: - rcar_sound,src : Should contain SRC feature. The number of SRC subnode should be same as HW. see below for detail. +- rcar_sound,dvc : Should contain DVC feature. + The number of DVC subnode should be same as HW. + see below for detail. - rcar_sound,dai : DAI contents. The number of DAI subnode should be same as HW. see below for detail. @@ -21,6 +24,7 @@ SSI subnode properties: - interrupts : Should contain SSI interrupt for PIO transfer - shared-pin : if shared clock pin - pio-transfer : use PIO transfer mode +- no-busif : BUSIF is not ussed when [mem -> SSI] via DMA case SRC subnode properties: no properties at this point @@ -39,6 +43,11 @@ rcar_sound: rcar_sound@0xffd90000 { <0 0xec540000 0 0x1000>, /* SSIU */ <0 0xec541000 0 0x1280>; /* SSI */ + rcar_sound,dvc { + dvc0: dvc@0 { }; + dvc1: dvc@1 { }; + }; + rcar_sound,src { src0: src@0 { }; src1: src@1 { }; diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt new file mode 100644 index 00000000000..6c55fcfe5e1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -0,0 +1,37 @@ +* Rockchip I2S controller + +The I2S bus (Inter-IC sound bus) is a serial link for digital +audio data transfer between devices in the system. + +Required properties: + +- compatible: should be one of the followings + - "rockchip,rk3066-i2s": for rk3066 + - "rockchip,rk3188-i2s", "rockchip,rk3066-i2s": for rk3188 + - "rockchip,rk3288-i2s", "rockchip,rk3066-i2s": for rk3288 +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: should contain the I2S interrupt. +- #address-cells: should be 1. +- #size-cells: should be 0. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: should include "tx" and "rx". +- clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. +- clock-names: should contain followings: + - "i2s_hclk": clock for I2S BUS + - "i2s_clk" : clock for I2S controller + +Example for rk3288 I2S controller: + +i2s@ff890000 { + compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s"; + reg = <0xff890000 0x10000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&pdma1 0>, <&pdma1 1>; + dma-names = "rx", "tx"; + clock-names = "i2s_hclk", "i2s_clk"; + clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt b/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt new file mode 100644 index 00000000000..9148f72319e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt @@ -0,0 +1,35 @@ +Samsung Exynos Odroid X2/U3 audio complex with MAX98090 codec + +Required properties: + - compatible : "samsung,odroidx2-audio" - for Odroid X2 board, + "samsung,odroidu3-audio" - for Odroid U3 board + - samsung,model : the user-visible name of this sound complex + - samsung,i2s-controller : the phandle of the I2S controller + - samsung,audio-codec : the phandle of the MAX98090 audio codec + - samsung,audio-routing : a list of the connections between audio + components; each entry is a pair of strings, the first being the + connection's sink, the second being the connection's source; + valid names for sources and sinks are the MAX98090's pins (as + documented in its binding), and the jacks on the board + For Odroid X2: + * Headphone Jack + * Mic Jack + * DMIC + + For Odroid U3: + * Headphone Jack + * Speakers + +Example: + +sound { + compatible = "samsung,odroidu3-audio"; + samsung,i2s-controller = <&i2s0>; + samsung,audio-codec = <&max98090>; + samsung,model = "Odroid-X2"; + samsung,audio-routing = + "Headphone Jack", "HPL", + "Headphone Jack", "HPR", + "IN1", "Mic Jack", + "Mic Jack", "MICBIAS"; +}; diff --git a/Documentation/devicetree/bindings/sound/sirf-usp.txt b/Documentation/devicetree/bindings/sound/sirf-usp.txt new file mode 100644 index 00000000000..02f85b32d35 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sirf-usp.txt @@ -0,0 +1,27 @@ +* SiRF SoC USP module + +Required properties: +- compatible: "sirf,prima2-usp-pcm" +- reg: Base address and size entries: +- dmas: List of DMA controller phandle and DMA request line ordered pairs. +- dma-names: Identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. + + One of the DMA channels will be responsible for transmission (should be + named "tx") and one for reception (should be named "rx"). + +- clocks: USP controller clock source +- pinctrl-names: Must contain a "default" entry. +- pinctrl-NNN: One property must exist for each entry in pinctrl-names. + +Example: +usp0: usp@b0080000 { + compatible = "sirf,prima2-usp-pcm"; + reg = <0xb0080000 0x10000>; + clocks = <&clks 28>; + dmas = <&dmac1 1>, <&dmac1 2>; + dma-names = "rx", "tx"; + pinctrl-names = "default"; + pinctrl-0 = <&usp0_only_utfs_pins_a>; +}; + diff --git a/Documentation/devicetree/bindings/sound/snow.txt b/Documentation/devicetree/bindings/sound/snow.txt index 678b191c37b..6df74f15687 100644 --- a/Documentation/devicetree/bindings/sound/snow.txt +++ b/Documentation/devicetree/bindings/sound/snow.txt @@ -3,15 +3,20 @@ Audio Binding for Snow boards Required properties: - compatible : Can be one of the following, "google,snow-audio-max98090" or + "google,snow-audio-max98091" or "google,snow-audio-max98095" - samsung,i2s-controller: The phandle of the Samsung I2S controller - samsung,audio-codec: The phandle of the audio codec +Optional: +- samsung,model: The name of the sound-card + Example: sound { compatible = "google,snow-audio-max98095"; + samsung,model = "Snow-I2S-MAX98095"; samsung,i2s-controller = <&i2s0>; samsung,audio-codec = <&max98095>; }; diff --git a/Documentation/devicetree/bindings/sound/tas2552.txt b/Documentation/devicetree/bindings/sound/tas2552.txt new file mode 100644 index 00000000000..55e2a0af564 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tas2552.txt @@ -0,0 +1,26 @@ +Texas Instruments - tas2552 Codec module + +The tas2552 serial control bus communicates through I2C protocols + +Required properties: + - compatible - One of: + "ti,tas2552" - TAS2552 + - reg - I2C slave address + - supply-*: Required supply regulators are: + "vbat" battery voltage + "iovdd" I/O Voltage + "avdd" Analog DAC Voltage + +Optional properties: + - enable-gpio - gpio pin to enable/disable the device + +Example: + +tas2552: tas2552@41 { + compatible = "ti,tas2552"; + reg = <0x41>; + enable-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; +}; + +For more product information please see the link below: +http://www.ti.com/product/TAS2552 diff --git a/Documentation/devicetree/bindings/sound/ti,tas5086.txt b/Documentation/devicetree/bindings/sound/ti,tas5086.txt index d2866a0d6a2..234dad296da 100644 --- a/Documentation/devicetree/bindings/sound/ti,tas5086.txt +++ b/Documentation/devicetree/bindings/sound/ti,tas5086.txt @@ -31,6 +31,9 @@ Optional properties: Most systems should not set any of these properties. + - avdd-supply: Power supply for AVDD, providing 3.3V + - dvdd-supply: Power supply for DVDD, providing 3.3V + Examples: i2c_bus { @@ -39,5 +42,7 @@ Examples: reg = <0x1b>; reset-gpio = <&gpio 23 0>; ti,charge-period = <156000>; + avdd-supply = <&vdd_3v3_reg>; + dvdd-supply = <&vdd_3v3_reg>; }; }; diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt index b82a268f1bd..bee6ff204ba 100644 --- a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt @@ -23,6 +23,12 @@ Optional properties: - spi-max-frequency: Specifies maximum SPI clock frequency, Units - Hz. Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt +- num-cs: total number of chipselects +- cs-gpios: should specify GPIOs used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child + nodes. If unspecified, a single SPI device without a chip + select can be used. + SPI slave nodes must be children of the SPI master node and can contain properties described in Documentation/devicetree/bindings/spi/spi-bus.txt diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 4d7f3758d1b..46a311e728a 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -83,6 +83,7 @@ mosaixtech Mosaix Technologies, Inc. moxa Moxa mpl MPL AG mundoreader Mundo Reader S.L. +murata Murata Manufacturing Co., Ltd. mxicy Macronix International Co., Ltd. national National Semiconductor neonode Neonode Inc. |