diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
10 files changed, 270 insertions, 79 deletions
diff --git a/Documentation/devicetree/bindings/misc/at25.txt b/Documentation/devicetree/bindings/misc/at25.txt index ab3c327929d..1d3447165c3 100644 --- a/Documentation/devicetree/bindings/misc/at25.txt +++ b/Documentation/devicetree/bindings/misc/at25.txt @@ -1,21 +1,35 @@ -Atmel AT25 eeprom +EEPROMs (SPI) compatible with Atmel at25. Required properties: - compatible : "atmel,at25". - reg : chip select number - spi-max-frequency : max spi frequency to use +- pagesize : size of the eeprom page +- size : total eeprom size in bytes +- address-width : number of address bits (one of 8, 16, or 24) +Optional properties: +- spi-cpha : SPI shifted clock phase, as per spi-bus bindings. +- spi-cpol : SPI inverse clock polarity, as per spi-bus bindings. +- read-only : this parameter-less property disables writes to the eeprom + +Obsolete legacy properties are can be used in place of "size", "pagesize", +"address-width", and "read-only": - at25,byte-len : total eeprom size in bytes - at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h - at25,page-size : size of the eeprom page -Examples: -at25@0 { - compatible = "atmel,at25"; - reg = <0> - spi-max-frequency = <5000000>; +Additional compatible properties are also allowed. + +Example: + at25@0 { + compatible = "atmel,at25", "st,m95256"; + reg = <0> + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; - at25,byte-len = <0x8000>; - at25,addr-mode = <2>; - at25,page-size = <64>; -}; + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; diff --git a/Documentation/devicetree/bindings/misc/lis302.txt b/Documentation/devicetree/bindings/misc/lis302.txt new file mode 100644 index 00000000000..6def86f6b05 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/lis302.txt @@ -0,0 +1,112 @@ +LIS302 accelerometer devicetree bindings + +This device is matched via its bus drivers, and has a number of properties +that apply in on the generic device (independent from the bus). + + +Required properties for the SPI bindings: + - compatible: should be set to "st,lis3lv02d_spi" + - reg: the chipselect index + - spi-max-frequency: maximal bus speed, should be set to 1000000 unless + constrained by external circuitry + - interrupts: the interrupt generated by the device + +Required properties for the I2C bindings: + - compatible: should be set to "st,lis3lv02d" + - reg: i2c slave address + - Vdd-supply: The input supply for Vdd + - Vdd_IO-supply: The input supply for Vdd_IO + + +Optional properties for all bus drivers: + + - st,click-single-{x,y,z}: if present, tells the device to issue an + interrupt on single click events on the + x/y/z axis. + - st,click-double-{x,y,z}: if present, tells the device to issue an + interrupt on double click events on the + x/y/z axis. + - st,click-thresh-{x,y,z}: set the x/y/z axis threshold + - st,click-click-time-limit: click time limit, from 0 to 127.5msec + with step of 0.5 msec + - st,click-latency: click latency, from 0 to 255 msec with + step of 1 msec. + - st,click-window: click window, from 0 to 255 msec with + step of 1 msec. + - st,irq{1,2}-disable: disable IRQ 1/2 + - st,irq{1,2}-ff-wu-1: raise IRQ 1/2 on FF_WU_1 condition + - st,irq{1,2}-ff-wu-2: raise IRQ 1/2 on FF_WU_2 condition + - st,irq{1,2}-data-ready: raise IRQ 1/2 on data ready contition + - st,irq{1,2}-click: raise IRQ 1/2 on click condition + - st,irq-open-drain: consider IRQ lines open-drain + - st,irq-active-low: make IRQ lines active low + - st,wu-duration-1: duration register for Free-Fall/Wake-Up + interrupt 1 + - st,wu-duration-2: duration register for Free-Fall/Wake-Up + interrupt 2 + - st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for + upper/lower limit + - st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of + highpass cut-off frequency + - st,hipass{1,2}-disable: disable highpass 1/2. + - st,default-rate=: set the default rate + - st,axis-{x,y,z}=: set the axis to map to the three coordinates + - st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis + (used by self-test) + + +Example for a SPI device node: + + lis302@0 { + compatible = "st,lis302dl-spi"; + reg = <0>; + spi-max-frequency = <1000000>; + interrupt-parent = <&gpio>; + interrupts = <104 0>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + }; + +Example for a I2C device node: + + lis331dlh: lis331dlh@18 { + compatible = "st,lis331dlh", "st,lis3lv02d"; + reg = <0x18>; + Vdd-supply = <&lis3_reg>; + Vdd_IO-supply = <&lis3_reg>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + st,min-limit-x = <120>; + st,min-limit-y = <120>; + st,min-limit-z = <140>; + st,max-limit-x = <550>; + st,max-limit-y = <550>; + st,max-limit-z = <750>; + }; + diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 66ece3f87bb..ecfc6ccd67e 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -11,10 +11,13 @@ Optional properties: - regulator-boot-on: bootloader/firmware enabled regulator - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) + +Deprecated properties: - regulator-compatible: If a regulator chip contains multiple regulators, and if the chip's binding contains a child node that describes each regulator, then this property indicates which regulator - this child node is intended to configure. + this child node is intended to configure. If this property is missing, + the node's name will be used instead. Example: diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index 0487e9675ba..d316fb895da 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -22,66 +22,49 @@ Example: compatible = "ti,tps65217"; regulators { - #address-cells = <1>; - #size-cells = <0>; - - dcdc1_reg: regulator@0 { - reg = <0>; - regulator-compatible = "dcdc1"; + dcdc1_reg: dcdc1 { regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; regulator-boot-on; regulator-always-on; }; - dcdc2_reg: regulator@1 { - reg = <1>; - regulator-compatible = "dcdc2"; + dcdc2_reg: dcdc2 { regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; - dcdc3_reg: regulator@2 { - reg = <2>; - regulator-compatible = "dcdc3"; + dcdc3_reg: dcc3 { regulator-min-microvolt = <900000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - ldo1_reg: regulator@3 { - reg = <3>; - regulator-compatible = "ldo1"; + ldo1_reg: ldo1 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; - ldo2_reg: regulator@4 { - reg = <4>; - regulator-compatible = "ldo2"; + ldo2_reg: ldo2 { regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; - ldo3_reg: regulator@5 { - reg = <5>; - regulator-compatible = "ldo3"; + ldo3_reg: ldo3 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; - ldo4_reg: regulator@6 { - reg = <6>; - regulator-compatible = "ldo4"; + ldo4_reg: ldo4 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; diff --git a/Documentation/devicetree/bindings/regulator/tps6586x.txt b/Documentation/devicetree/bindings/regulator/tps6586x.txt index da80c2ae091..07b9ef6e49d 100644 --- a/Documentation/devicetree/bindings/regulator/tps6586x.txt +++ b/Documentation/devicetree/bindings/regulator/tps6586x.txt @@ -6,9 +6,13 @@ Required properties: - interrupts: the interrupt outputs of the controller - #gpio-cells: number of cells to describe a GPIO - gpio-controller: mark the device as a GPIO controller -- regulators: list of regulators provided by this controller, must have - property "regulator-compatible" to match their hardware counterparts: - sm[0-2], ldo[0-9] and ldo_rtc +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name (or the deprecated + regulator-compatible property if present), with valid values listed below. + The content of each sub-node is defined by the standard binding for + regulators; see regulator.txt. + sys, sm[0-2], ldo[0-9] and ldo_rtc +- sys-supply: The input supply for SYS. - vin-sm0-supply: The input supply for the SM0. - vin-sm1-supply: The input supply for the SM1. - vin-sm2-supply: The input supply for the SM2. @@ -20,6 +24,9 @@ Required properties: Each regulator is defined using the standard binding for regulators. +Note: LDO5 and LDO_RTC is supplied by SYS regulator internally and driver + take care of making proper parent child relationship. + Example: pmu: tps6586x@34 { @@ -30,6 +37,7 @@ Example: #gpio-cells = <2>; gpio-controller; + sys-supply = <&some_reg>; vin-sm0-supply = <&some_reg>; vin-sm1-supply = <&some_reg>; vin-sm2-supply = <&some_reg>; @@ -40,103 +48,80 @@ Example: vinldo9-supply = <...>; regulators { - #address-cells = <1>; - #size-cells = <0>; + sys_reg: sys { + regulator-name = "vdd_sys"; + regulator-boot-on; + regulator-always-on; + }; - sm0_reg: regulator@0 { - reg = <0>; - regulator-compatible = "sm0"; + sm0_reg: sm0 { regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm1_reg: regulator@1 { - reg = <1>; - regulator-compatible = "sm1"; + sm1_reg: sm1 { regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm2_reg: regulator@2 { - reg = <2>; - regulator-compatible = "sm2"; + sm2_reg: sm2 { regulator-min-microvolt = <3000000>; regulator-max-microvolt = <4550000>; regulator-boot-on; regulator-always-on; }; - ldo0_reg: regulator@3 { - reg = <3>; - regulator-compatible = "ldo0"; + ldo0_reg: ldo0 { regulator-name = "PCIE CLK"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; - ldo1_reg: regulator@4 { - reg = <4>; - regulator-compatible = "ldo1"; + ldo1_reg: ldo1 { regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo2_reg: regulator@5 { - reg = <5>; - regulator-compatible = "ldo2"; + ldo2_reg: ldo2 { regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo3_reg: regulator@6 { - reg = <6>; - regulator-compatible = "ldo3"; + ldo3_reg: ldo3 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo4_reg: regulator@7 { - reg = <7>; - regulator-compatible = "ldo4"; + ldo4_reg: ldo4 { regulator-min-microvolt = <1700000>; regulator-max-microvolt = <2475000>; }; - ldo5_reg: regulator@8 { - reg = <8>; - regulator-compatible = "ldo5"; + ldo5_reg: ldo5 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo6_reg: regulator@9 { - reg = <9>; - regulator-compatible = "ldo6"; + ldo6_reg: ldo6 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo7_reg: regulator@10 { - reg = <10>; - regulator-compatible = "ldo7"; + ldo7_reg: ldo7 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo8_reg: regulator@11 { - reg = <11>; - regulator-compatible = "ldo8"; + ldo8_reg: ldo8 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo9_reg: regulator@12 { - reg = <12>; - regulator-compatible = "ldo9"; + ldo9_reg: ldo9 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; diff --git a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt new file mode 100644 index 00000000000..801d58cb6d4 --- /dev/null +++ b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt @@ -0,0 +1,15 @@ +* Freescale i.MX28 LRADC device driver + +Required properties: +- compatible: Should be "fsl,imx28-lradc" +- reg: Address and length of the register set for the device +- interrupts: Should contain the LRADC interrupts + +Examples: + + lradc@80050000 { + compatible = "fsl,imx28-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <10 14 15 16 17 18 19 + 20 21 22 23 24 25>; + }; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt new file mode 100644 index 00000000000..07654f0338b --- /dev/null +++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt @@ -0,0 +1,41 @@ +Freescale i.MX IPUv3 +==================== + +Required properties: +- compatible: Should be "fsl,<chip>-ipu" +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain sync interrupt and error interrupt, + in this order. +- #crtc-cells: 1, See below + +example: + +ipu: ipu@18000000 { + #crtc-cells = <1>; + compatible = "fsl,imx53-ipu"; + reg = <0x18000000 0x080000000>; + interrupts = <11 10>; +}; + +Parallel display support +======================== + +Required properties: +- compatible: Should be "fsl,imx-parallel-display" +- crtc: the crtc this display is connected to, see below +Optional properties: +- interface_pix_fmt: How this display is connected to the + crtc. Currently supported types: "rgb24", "rgb565" +- edid: verbatim EDID data block describing attached display. +- ddc: phandle describing the i2c bus handling the display data + channel + +example: + +display@di0 { + compatible = "fsl,imx-parallel-display"; + edid = [edid-data]; + crtc = <&ipu 0>; + interface-pix-fmt = "rgb24"; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt new file mode 100644 index 00000000000..0d439dfc1aa --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt @@ -0,0 +1,14 @@ +* NXP LPC32xx SoC High Speed UART + +Required properties: +- compatible: Should be "nxp,lpc3220-hsuart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt + +Example: + + uart1: serial@40014000 { + compatible = "nxp,lpc3220-hsuart"; + reg = <0x40014000 0x1000>; + interrupts = <26 0>; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt index 0847fdeee11..ba385f2e0dd 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -25,6 +25,8 @@ Optional properties: accesses to the UART (e.g. TI davinci). - used-by-rtas : set to indicate that the port is in use by the OpenFirmware RTAS and should not be registered. +- no-loopback-test: set to indicate that the port does not implements loopback + test mode Example: diff --git a/Documentation/devicetree/bindings/w1/w1-gpio.txt b/Documentation/devicetree/bindings/w1/w1-gpio.txt new file mode 100644 index 00000000000..6e09c35d9f1 --- /dev/null +++ b/Documentation/devicetree/bindings/w1/w1-gpio.txt @@ -0,0 +1,22 @@ +w1-gpio devicetree bindings + +Required properties: + + - compatible: "w1-gpio" + - gpios: one or two GPIO specs: + - the first one is used as data I/O pin + - the second one is optional. If specified, it is used as + enable pin for an external pin pullup. + +Optional properties: + + - linux,open-drain: if specified, the data pin is considered in + open-drain mode. + +Examples: + + onewire@0 { + compatible = "w1-gpio"; + gpios = <&gpio 126 0>, <&gpio 105 0>; + }; + |