diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
16 files changed, 190 insertions, 22 deletions
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 34dc40cffdf..af9b4a0d902 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -91,7 +91,7 @@ Boards: compatible = "ti,omap3-beagle", "ti,omap3" - OMAP3 Tobi with Overo : Commercial expansion board with daughter board - compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3" + compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3" - OMAP4 SDP : Software Development Board compatible = "ti,omap4-sdp", "ti,omap4430" diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index a6a352c2771..5992dceec7a 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -21,9 +21,9 @@ Required Properties: must appear in the same order as the output clocks. - #clock-cells: Must be 1 - clock-output-names: The name of the clocks as free-form strings - - renesas,indices: Indices of the gate clocks into the group (0 to 31) + - renesas,clock-indices: Indices of the gate clocks into the group (0 to 31) -The clocks, clock-output-names and renesas,indices properties contain one +The clocks, clock-output-names and renesas,clock-indices properties contain one entry per gate clock. The MSTP groups are sparsely populated. Unimplemented gate clocks must not be declared. diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index 68b83ecc385..ee9be996152 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -1,12 +1,16 @@ * Freescale Smart Direct Memory Access (SDMA) Controller for i.MX Required properties: -- compatible : Should be "fsl,imx31-sdma", "fsl,imx31-to1-sdma", - "fsl,imx31-to2-sdma", "fsl,imx35-sdma", "fsl,imx35-to1-sdma", - "fsl,imx35-to2-sdma", "fsl,imx51-sdma", "fsl,imx53-sdma" or - "fsl,imx6q-sdma". The -to variants should be preferred since they - allow to determnine the correct ROM script addresses needed for - the driver to work without additional firmware. +- compatible : Should be one of + "fsl,imx25-sdma" + "fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma" + "fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma" + "fsl,imx51-sdma" + "fsl,imx53-sdma" + "fsl,imx6q-sdma" + The -to variants should be preferred since they allow to determnine the + correct ROM script addresses needed for the driver to work without additional + firmware. - reg : Should contain SDMA registers location and length - interrupts : Should contain SDMA interrupt - #dma-cells : Must be <3>. diff --git a/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt new file mode 100644 index 00000000000..aee38e7c13e --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt @@ -0,0 +1,18 @@ +TI-NSPIRE interrupt controller + +Required properties: +- compatible: Compatible property value should be "lsi,zevio-intc". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- interrupt-controller : Identifies the node as an interrupt controller + +Example: + +interrupt-controller { + compatible = "lsi,zevio-intc"; + interrupt-controller; + reg = <0xDC000000 0x1000>; + #interrupt-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt index 0a85c70cd30..07ad02075a9 100644 --- a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt @@ -13,6 +13,9 @@ Required properties: - #address-cells: should be one. The cell is the slot id. - #size-cells: should be zero. - at least one slot node +- clock-names: tuple listing input clock names. + Required elements: "mci_clk" +- clocks: phandles to input clocks. The node contains child nodes for each slot that the platform uses @@ -24,6 +27,8 @@ mmc0: mmc@f0008000 { interrupts = <12 4>; #address-cells = <1>; #size-cells = <0>; + clock-names = "mci_clk"; + clocks = <&mci0_clk>; [ child node definitions...] }; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt index b90bfcd138f..863d5b8155c 100644 --- a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt @@ -1,7 +1,8 @@ * Allwinner EMAC ethernet controller Required properties: -- compatible: should be "allwinner,sun4i-emac". +- compatible: should be "allwinner,sun4i-a10-emac" (Deprecated: + "allwinner,sun4i-emac") - reg: address and length of the register set for the device. - interrupts: interrupt for the device - phy: A phandle to a phy node defining the PHY address (as the reg @@ -14,7 +15,7 @@ Optional properties: Example: emac: ethernet@01c0b000 { - compatible = "allwinner,sun4i-emac"; + compatible = "allwinner,sun4i-a10-emac"; reg = <0x01c0b000 0x1000>; interrupts = <55>; clocks = <&ahb_gates 17>; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt index 00b9f9a3ec1..4ec56413779 100644 --- a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt @@ -1,7 +1,8 @@ * Allwinner A10 MDIO Ethernet Controller interface Required properties: -- compatible: should be "allwinner,sun4i-mdio". +- compatible: should be "allwinner,sun4i-a10-mdio" + (Deprecated: "allwinner,sun4i-mdio"). - reg: address and length of the register set for the device. Optional properties: @@ -9,7 +10,7 @@ Optional properties: Example at the SoC level: mdio@01c0b080 { - compatible = "allwinner,sun4i-mdio"; + compatible = "allwinner,sun4i-a10-mdio"; reg = <0x01c0b080 0x14>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/micrel-ks8851.txt b/Documentation/devicetree/bindings/net/micrel-ks8851.txt index 11ace3c3d80..4fc39276361 100644 --- a/Documentation/devicetree/bindings/net/micrel-ks8851.txt +++ b/Documentation/devicetree/bindings/net/micrel-ks8851.txt @@ -7,3 +7,4 @@ Required properties: Optional properties: - local-mac-address : Ethernet mac address to use +- vdd-supply: supply for Ethernet mac diff --git a/Documentation/devicetree/bindings/net/opencores-ethoc.txt b/Documentation/devicetree/bindings/net/opencores-ethoc.txt new file mode 100644 index 00000000000..2dc127c30d9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/opencores-ethoc.txt @@ -0,0 +1,22 @@ +* OpenCores MAC 10/100 Mbps + +Required properties: +- compatible: Should be "opencores,ethoc". +- reg: two memory regions (address and length), + first region is for the device registers and descriptor rings, + second is for the device packet memory. +- interrupts: interrupt for the device. + +Optional properties: +- clocks: phandle to refer to the clk used as per + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Examples: + + enet0: ethoc@fd030000 { + compatible = "opencores,ethoc"; + reg = <0xfd030000 0x4000 0xfd800000 0x4000>; + interrupts = <1>; + local-mac-address = [00 50 c2 13 6f 00]; + clocks = <&osc>; + }; diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt new file mode 100644 index 00000000000..3dd3d0bf112 --- /dev/null +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -0,0 +1,58 @@ +STMicroelectronics SoC DWMAC glue layer controller + +The device node has following properties. + +Required properties: + - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac" or + "st,stid127-dwmac". + - reg : Offset of the glue configuration register map in system + configuration regmap pointed by st,syscon property and size. + + - reg-names : Should be "sti-ethconf". + + - st,syscon : Should be phandle to system configuration node which + encompases this glue registers. + + - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be + wired up in from different sources. One via TXCLK pin and other via CLK_125 + pin. This wiring is totally board dependent. However the retiming glue + logic should be configured accordingly. Possible values for this property + + "txclk" - if 125Mhz clock is wired up via txclk line. + "clk_125" - if 125Mhz clock is wired up via clk_125 line. + + This property is only valid for Giga bit setup( GMII, RGMII), and it is + un-used for non-giga bit (MII and RMII) setups. Also note that internal + clockgen can not generate stable 125Mhz clock. + + - st,ext-phyclk: This boolean property indicates who is generating the clock + for tx and rx. This property is only valid for RMII case where the clock can + be generated from the MAC or PHY. + + - clock-names: should be "sti-ethclk". + - clocks: Should point to ethernet clockgen which can generate phyclk. + + +Example: + +ethernet0: dwmac@fe810000 { + device_type = "network"; + compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + reg = <0xfe810000 0x8000>, <0x8bc 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + interrupts = <0 133 0>, <0 134 0>, <0 135 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + phy-mode = "mii"; + + st,syscon = <&syscfg_rear>; + + snps,pbl = <32>; + snps,mixed-burst; + + resets = <&softreset STIH416_ETH0_SOFTRESET>; + reset-names = "stmmaceth"; + pinctrl-0 = <&pinctrl_mii0>; + pinctrl-names = "default"; + clocks = <&CLK_S_GMAC0_PHY>; + clock-names = "stmmaceth"; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt index 9e9e9ef9f85..c119debe6ba 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt @@ -1,4 +1,4 @@ -Broadcom Capri Pin Controller +Broadcom BCM281xx Pin Controller This is a pin controller for the Broadcom BCM281xx SoC family, which includes BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs. @@ -7,14 +7,14 @@ BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs. Required Properties: -- compatible: Must be "brcm,capri-pinctrl". +- compatible: Must be "brcm,bcm11351-pinctrl" - reg: Base address of the PAD Controller register block and the size of the block. For example, the following is the bare minimum node: pinctrl@35004800 { - compatible = "brcm,capri-pinctrl"; + compatible = "brcm,bcm11351-pinctrl"; reg = <0x35004800 0x430>; }; @@ -119,7 +119,7 @@ Optional Properties (for HDMI pins): Example: // pin controller node pinctrl@35004800 { - compatible = "brcm,capri-pinctrl"; + compatible = "brcmbcm11351-pinctrl"; reg = <0x35004800 0x430>; // pin configuration node diff --git a/Documentation/devicetree/bindings/power/bq2415x.txt b/Documentation/devicetree/bindings/power/bq2415x.txt new file mode 100644 index 00000000000..d0327f0b59a --- /dev/null +++ b/Documentation/devicetree/bindings/power/bq2415x.txt @@ -0,0 +1,47 @@ +Binding for TI bq2415x Li-Ion Charger + +Required properties: +- compatible: Should contain one of the following: + * "ti,bq24150" + * "ti,bq24150" + * "ti,bq24150a" + * "ti,bq24151" + * "ti,bq24151a" + * "ti,bq24152" + * "ti,bq24153" + * "ti,bq24153a" + * "ti,bq24155" + * "ti,bq24156" + * "ti,bq24156a" + * "ti,bq24158" +- reg: integer, i2c address of the device. +- ti,current-limit: integer, initial maximum current charger can pull + from power supply in mA. +- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV. + The chip will use slow precharge if battery voltage + is below this value. +- ti,battery-regulation-voltage: integer, maximum charging voltage in mV. +- ti,charge-current: integer, maximum charging current in mA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in mA). +- ti,resistor-sense: integer, value of sensing resistor in milliohm. + +Optional properties: +- ti,usb-charger-detection: phandle to usb charger detection device. + (required for auto mode) + +Example from Nokia N900: + +bq24150a { + compatible = "ti,bq24150a"; + reg = <0x6b>; + + ti,current-limit = <100>; + ti,weak-battery-voltage = <3400>; + ti,battery-regulation-voltage = <4200>; + ti,charge-current = <650>; + ti,termination-current = <100>; + ti,resistor-sense = <68>; + + ti,usb-charger-detection = <&isp1704>; +}; diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt index a590ca51be7..8f081c96a4f 100644 --- a/Documentation/devicetree/bindings/spi/efm32-spi.txt +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -3,24 +3,24 @@ Required properties: - #address-cells: see spi-bus.txt - #size-cells: see spi-bus.txt -- compatible: should be "efm32,spi" +- compatible: should be "energymicro,efm32-spi" - reg: Offset and length of the register set for the controller - interrupts: pair specifying rx and tx irq - clocks: phandle to the spi clock - cs-gpios: see spi-bus.txt -- location: Value to write to the ROUTE register's LOCATION bitfield to configure the pinmux for the device, see datasheet for values. +- efm32,location: Value to write to the ROUTE register's LOCATION bitfield to configure the pinmux for the device, see datasheet for values. Example: spi1: spi@0x4000c400 { /* USART1 */ #address-cells = <1>; #size-cells = <0>; - compatible = "efm32,spi"; + compatible = "energymicro,efm32-spi"; reg = <0x4000c400 0x400>; interrupts = <15 16>; clocks = <&cmu 20>; cs-gpios = <&gpio 51 1>; // D3 - location = <1>; + efm32,location = <1>; status = "ok"; ks8851@0 { diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index a1fb3035a42..5376de40f10 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -10,6 +10,7 @@ Required properties: - pinctrl-names: must contain a "default" entry. - spi-num-chipselects : the number of the chipselect signals. - bus-num : the slave chip chipselect signal number. +- big-endian : if DSPI modudle is big endian, the bool will be set in node. Example: dspi0@4002c000 { @@ -24,6 +25,7 @@ dspi0@4002c000 { bus-num = <0>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dspi0_1>; + big-endian; status = "okay"; sflash: at26df081a@0 { diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt index 07e04cdc0c9..4f8184d069c 100644 --- a/Documentation/devicetree/bindings/spi/spi_atmel.txt +++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt @@ -5,6 +5,9 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain spi interrupt - cs-gpios: chipselects +- clock-names: tuple listing input clock names. + Required elements: "spi_clk" +- clocks: phandles to input clocks. Example: @@ -14,6 +17,8 @@ spi1: spi@fffcc000 { interrupts = <13 4 5>; #address-cells = <1>; #size-cells = <0>; + clocks = <&spi1_clk>; + clock-names = "spi_clk"; cs-gpios = <&pioB 3 0>; status = "okay"; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 3f900cd51bf..40ce2df0e0e 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -8,6 +8,7 @@ ad Avionic Design GmbH adi Analog Devices, Inc. aeroflexgaisler Aeroflex Gaisler AB ak Asahi Kasei Corp. +allwinner Allwinner Technology Co., Ltd. altr Altera Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amstaos AMS-Taos Inc. @@ -40,6 +41,7 @@ gmt Global Mixed-mode Technology, Inc. gumstix Gumstix, Inc. haoyu Haoyu Microelectronic Co. Ltd. hisilicon Hisilicon Limited. +honeywell Honeywell hp Hewlett Packard ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. @@ -55,6 +57,7 @@ maxim Maxim Integrated Products microchip Microchip Technology Inc. mosaixtech Mosaix Technologies, Inc. national National Semiconductor +neonode Neonode Inc. nintendo Nintendo nvidia NVIDIA nxp NXP Semiconductors @@ -64,7 +67,7 @@ phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. -qcom Qualcomm, Inc. +qcom Qualcomm Technologies, Inc ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International realtek Realtek Semiconductor Corp. @@ -78,6 +81,7 @@ silabs Silicon Laboratories simtek sirf SiRF Technology, Inc. snps Synopsys, Inc. +spansion Spansion Inc. st STMicroelectronics ste ST-Ericsson stericsson ST-Ericsson |