diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
62 files changed, 2339 insertions, 89 deletions
diff --git a/Documentation/devicetree/bindings/arm/bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm2835.txt new file mode 100644 index 00000000000..ac683480c48 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm2835.txt @@ -0,0 +1,8 @@ +Broadcom BCM2835 device tree bindings +------------------------------------------- + +Boards with the BCM2835 SoC shall have the following properties: + +Required root node property: + +compatible = "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/arm/mrvl/tauros2.txt b/Documentation/devicetree/bindings/arm/mrvl/tauros2.txt new file mode 100644 index 00000000000..31af1cbb60b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mrvl/tauros2.txt @@ -0,0 +1,17 @@ +* Marvell Tauros2 Cache + +Required properties: +- compatible : Should be "marvell,tauros2-cache". +- marvell,tauros2-cache-features : Specify the features supported for the + tauros2 cache. + The features including + CACHE_TAUROS2_PREFETCH_ON (1 << 0) + CACHE_TAUROS2_LINEFILL_BURST8 (1 << 1) + The definition can be found at + arch/arm/include/asm/hardware/cache-tauros2.h + +Example: + L2: l2-cache { + compatible = "marvell,tauros2-cache"; + marvell,tauros2-cache-features = <0x3>; + }; diff --git a/Documentation/devicetree/bindings/arm/msm/timer.txt b/Documentation/devicetree/bindings/arm/msm/timer.txt new file mode 100644 index 00000000000..8c5907b9cae --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/timer.txt @@ -0,0 +1,38 @@ +* MSM Timer + +Properties: + +- compatible : Should at least contain "qcom,msm-timer". More specific + properties such as "qcom,msm-gpt" and "qcom,msm-dgt" specify a general + purpose timer and a debug timer respectively. + +- interrupts : Interrupt indicating a match event. + +- reg : Specifies the base address of the timer registers. The second region + specifies an optional register used to configure the clock divider. + +- clock-frequency : The frequency of the timer in Hz. + +Optional: + +- cpu-offset : per-cpu offset used when the timer is accessed without the + CPU remapping facilities. The offset is cpu-offset * cpu-nr. + +Example: + + timer@200a004 { + compatible = "qcom,msm-gpt", "qcom,msm-timer"; + interrupts = <1 2 0x301>; + reg = <0x0200a004 0x10>; + clock-frequency = <32768>; + cpu-offset = <0x40000>; + }; + + timer@200a024 { + compatible = "qcom,msm-dgt", "qcom,msm-timer"; + interrupts = <1 3 0x301>; + reg = <0x0200a024 0x10>, + <0x0200a034 0x4>; + clock-frequency = <6750000>; + cpu-offset = <0x40000>; + }; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index ccdd0e53451..d0051a75058 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -36,6 +36,9 @@ Boards: - OMAP3 BeagleBoard : Low cost community board compatible = "ti,omap3-beagle", "ti,omap3" +- OMAP3 Tobi with Overo : Commercial expansion board with daughter board + compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3" + - OMAP4 SDP : Software Developement Board compatible = "ti,omap4-sdp", "ti,omap4430" diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 1c044eb320c..343781b9f24 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -7,8 +7,12 @@ representation in the device tree should be done as under:- Required properties: - compatible : should be one of + "arm,cortex-a15-pmu" "arm,cortex-a9-pmu" "arm,cortex-a8-pmu" + "arm,cortex-a7-pmu" + "arm,cortex-a5-pmu" + "arm,arm11mpcore-pmu" "arm,arm1176-pmu" "arm,arm1136-pmu" - interrupts : 1 combined interrupt or 1 per core. diff --git a/Documentation/devicetree/bindings/arm/vt8500.txt b/Documentation/devicetree/bindings/arm/vt8500.txt new file mode 100644 index 00000000000..d657832c681 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500.txt @@ -0,0 +1,14 @@ +VIA/Wondermedia VT8500 Platforms Device Tree Bindings +--------------------------------------- + +Boards with the VIA VT8500 SoC shall have the following properties: +Required root node property: +compatible = "via,vt8500"; + +Boards with the Wondermedia WM8505 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8505"; + +Boards with the Wondermedia WM8650 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8650"; diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt new file mode 100644 index 00000000000..0a4ce1051b0 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt @@ -0,0 +1,16 @@ +VIA/Wondermedia VT8500 Interrupt Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-intc" +- reg : Should contain 1 register ranges(address and length) +- #interrupt-cells : should be <1> + +Example: + + intc: interrupt-controller@d8140000 { + compatible = "via,vt8500-intc"; + interrupt-controller; + reg = <0xd8140000 0x10000>; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt new file mode 100644 index 00000000000..521b9c7de93 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt @@ -0,0 +1,13 @@ +VIA/Wondermedia VT8500 Power Management Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-pmc" +- reg : Should contain 1 register ranges(address and length) + +Example: + + pmc@d8130000 { + compatible = "via,vt8500-pmc"; + reg = <0xd8130000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt new file mode 100644 index 00000000000..901c73f0d8e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 Timer +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-timer" +- reg : Should contain 1 register ranges(address and length) +- interrupts : interrupt for the timer + +Example: + + timer@d8130100 { + compatible = "via,vt8500-timer"; + reg = <0xd8130100 0x28>; + interrupts = <36>; + }; diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt new file mode 100644 index 00000000000..d2fe064a828 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt @@ -0,0 +1,10 @@ +* OMAP OCP2SCP - ocp interface to scp interface + +properties: +- compatible : Should be "ti,omap-ocp2scp" +- #address-cells, #size-cells : Must be present if the device has sub-nodes +- ranges : the child address space are mapped 1:1 onto the parent address space +- ti,hwmods : must be "ocp2scp_usb_phy" + +Sub-nodes: +All the devices connected to ocp2scp are described using sub-node to ocp2scp diff --git a/Documentation/devicetree/bindings/clock/imx23-clock.txt b/Documentation/devicetree/bindings/clock/imx23-clock.txt new file mode 100644 index 00000000000..a0b867ef8d9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx23-clock.txt @@ -0,0 +1,76 @@ +* Clock bindings for Freescale i.MX23 + +Required properties: +- compatible: Should be "fsl,imx23-clkctrl" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX23 +clocks and IDs. + + Clock ID + ------------------ + ref_xtal 0 + pll 1 + ref_cpu 2 + ref_emi 3 + ref_pix 4 + ref_io 5 + saif_sel 6 + lcdif_sel 7 + gpmi_sel 8 + ssp_sel 9 + emi_sel 10 + cpu 11 + etm_sel 12 + cpu_pll 13 + cpu_xtal 14 + hbus 15 + xbus 16 + lcdif_div 17 + ssp_div 18 + gpmi_div 19 + emi_pll 20 + emi_xtal 21 + etm_div 22 + saif_div 23 + clk32k_div 24 + rtc 25 + adc 26 + spdif_div 27 + clk32k 28 + dri 29 + pwm 30 + filt 31 + uart 32 + ssp 33 + gpmi 34 + spdif 35 + emi 36 + saif 37 + lcdif 38 + etm 39 + usb 40 + usb_pwr 41 + +Examples: + +clks: clkctrl@80040000 { + compatible = "fsl,imx23-clkctrl"; + reg = <0x80040000 0x2000>; + #clock-cells = <1>; + clock-output-names = + ... + "uart", /* 32 */ + ... + "end_of_list"; +}; + +auart0: serial@8006c000 { + compatible = "fsl,imx23-auart"; + reg = <0x8006c000 0x2000>; + interrupts = <24 25 23>; + clocks = <&clks 32>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx28-clock.txt b/Documentation/devicetree/bindings/clock/imx28-clock.txt new file mode 100644 index 00000000000..aa2af2866fe --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx28-clock.txt @@ -0,0 +1,99 @@ +* Clock bindings for Freescale i.MX28 + +Required properties: +- compatible: Should be "fsl,imx28-clkctrl" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX28 +clocks and IDs. + + Clock ID + ------------------ + ref_xtal 0 + pll0 1 + pll1 2 + pll2 3 + ref_cpu 4 + ref_emi 5 + ref_io0 6 + ref_io1 7 + ref_pix 8 + ref_hsadc 9 + ref_gpmi 10 + saif0_sel 11 + saif1_sel 12 + gpmi_sel 13 + ssp0_sel 14 + ssp1_sel 15 + ssp2_sel 16 + ssp3_sel 17 + emi_sel 18 + etm_sel 19 + lcdif_sel 20 + cpu 21 + ptp_sel 22 + cpu_pll 23 + cpu_xtal 24 + hbus 25 + xbus 26 + ssp0_div 27 + ssp1_div 28 + ssp2_div 29 + ssp3_div 30 + gpmi_div 31 + emi_pll 32 + emi_xtal 33 + lcdif_div 34 + etm_div 35 + ptp 36 + saif0_div 37 + saif1_div 38 + clk32k_div 39 + rtc 40 + lradc 41 + spdif_div 42 + clk32k 43 + pwm 44 + uart 45 + ssp0 46 + ssp1 47 + ssp2 48 + ssp3 49 + gpmi 50 + spdif 51 + emi 52 + saif0 53 + saif1 54 + lcdif 55 + etm 56 + fec 57 + can0 58 + can1 59 + usb0 60 + usb1 61 + usb0_pwr 62 + usb1_pwr 63 + enet_out 64 + +Examples: + +clks: clkctrl@80040000 { + compatible = "fsl,imx28-clkctrl"; + reg = <0x80040000 0x2000>; + #clock-cells = <1>; + clock-output-names = + ... + "uart", /* 45 */ + ... + "end_of_list"; +}; + +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112 70 71>; + clocks = <&clks 45>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt new file mode 100644 index 00000000000..492bd991d52 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -0,0 +1,222 @@ +* Clock bindings for Freescale i.MX6 Quad + +Required properties: +- compatible: Should be "fsl,imx6q-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX6Q +clocks and IDs. + + Clock ID + --------------------------- + dummy 0 + ckil 1 + ckih 2 + osc 3 + pll2_pfd0_352m 4 + pll2_pfd1_594m 5 + pll2_pfd2_396m 6 + pll3_pfd0_720m 7 + pll3_pfd1_540m 8 + pll3_pfd2_508m 9 + pll3_pfd3_454m 10 + pll2_198m 11 + pll3_120m 12 + pll3_80m 13 + pll3_60m 14 + twd 15 + step 16 + pll1_sw 17 + periph_pre 18 + periph2_pre 19 + periph_clk2_sel 20 + periph2_clk2_sel 21 + axi_sel 22 + esai_sel 23 + asrc_sel 24 + spdif_sel 25 + gpu2d_axi 26 + gpu3d_axi 27 + gpu2d_core_sel 28 + gpu3d_core_sel 29 + gpu3d_shader_sel 30 + ipu1_sel 31 + ipu2_sel 32 + ldb_di0_sel 33 + ldb_di1_sel 34 + ipu1_di0_pre_sel 35 + ipu1_di1_pre_sel 36 + ipu2_di0_pre_sel 37 + ipu2_di1_pre_sel 38 + ipu1_di0_sel 39 + ipu1_di1_sel 40 + ipu2_di0_sel 41 + ipu2_di1_sel 42 + hsi_tx_sel 43 + pcie_axi_sel 44 + ssi1_sel 45 + ssi2_sel 46 + ssi3_sel 47 + usdhc1_sel 48 + usdhc2_sel 49 + usdhc3_sel 50 + usdhc4_sel 51 + enfc_sel 52 + emi_sel 53 + emi_slow_sel 54 + vdo_axi_sel 55 + vpu_axi_sel 56 + cko1_sel 57 + periph 58 + periph2 59 + periph_clk2 60 + periph2_clk2 61 + ipg 62 + ipg_per 63 + esai_pred 64 + esai_podf 65 + asrc_pred 66 + asrc_podf 67 + spdif_pred 68 + spdif_podf 69 + can_root 70 + ecspi_root 71 + gpu2d_core_podf 72 + gpu3d_core_podf 73 + gpu3d_shader 74 + ipu1_podf 75 + ipu2_podf 76 + ldb_di0_podf 77 + ldb_di1_podf 78 + ipu1_di0_pre 79 + ipu1_di1_pre 80 + ipu2_di0_pre 81 + ipu2_di1_pre 82 + hsi_tx_podf 83 + ssi1_pred 84 + ssi1_podf 85 + ssi2_pred 86 + ssi2_podf 87 + ssi3_pred 88 + ssi3_podf 89 + uart_serial_podf 90 + usdhc1_podf 91 + usdhc2_podf 92 + usdhc3_podf 93 + usdhc4_podf 94 + enfc_pred 95 + enfc_podf 96 + emi_podf 97 + emi_slow_podf 98 + vpu_axi_podf 99 + cko1_podf 100 + axi 101 + mmdc_ch0_axi_podf 102 + mmdc_ch1_axi_podf 103 + arm 104 + ahb 105 + apbh_dma 106 + asrc 107 + can1_ipg 108 + can1_serial 109 + can2_ipg 110 + can2_serial 111 + ecspi1 112 + ecspi2 113 + ecspi3 114 + ecspi4 115 + ecspi5 116 + enet 117 + esai 118 + gpt_ipg 119 + gpt_ipg_per 120 + gpu2d_core 121 + gpu3d_core 122 + hdmi_iahb 123 + hdmi_isfr 124 + i2c1 125 + i2c2 126 + i2c3 127 + iim 128 + enfc 129 + ipu1 130 + ipu1_di0 131 + ipu1_di1 132 + ipu2 133 + ipu2_di0 134 + ldb_di0 135 + ldb_di1 136 + ipu2_di1 137 + hsi_tx 138 + mlb 139 + mmdc_ch0_axi 140 + mmdc_ch1_axi 141 + ocram 142 + openvg_axi 143 + pcie_axi 144 + pwm1 145 + pwm2 146 + pwm3 147 + pwm4 148 + per1_bch 149 + gpmi_bch_apb 150 + gpmi_bch 151 + gpmi_io 152 + gpmi_apb 153 + sata 154 + sdma 155 + spba 156 + ssi1 157 + ssi2 158 + ssi3 159 + uart_ipg 160 + uart_serial 161 + usboh3 162 + usdhc1 163 + usdhc2 164 + usdhc3 165 + usdhc4 166 + vdo_axi 167 + vpu_axi 168 + cko1 169 + pll1_sys 170 + pll2_bus 171 + pll3_usb_otg 172 + pll4_audio 173 + pll5_video 174 + pll6_mlb 175 + pll7_usb_host 176 + pll8_enet 177 + ssi1_ipg 178 + ssi2_ipg 179 + ssi3_ipg 180 + rom 181 + usbphy1 182 + usbphy2 183 + ldb_di0_div_3_5 184 + ldb_di1_div_3_5 185 + +Examples: + +clks: ccm@020c4000 { + compatible = "fsl,imx6q-ccm"; + reg = <0x020c4000 0x4000>; + interrupts = <0 87 0x04 0 88 0x04>; + #clock-cells = <1>; + clock-output-names = ... + "uart_ipg", + "uart_serial", + ...; +}; + +uart1: serial@02020000 { + compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; + reg = <0x02020000 0x4000>; + interrupts = <0 26 0x04>; + clocks = <&clks 160>, <&clks 161>; + clock-names = "ipg", "per"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/vt8500.txt b/Documentation/devicetree/bindings/clock/vt8500.txt new file mode 100644 index 00000000000..a880c70d004 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/vt8500.txt @@ -0,0 +1,72 @@ +Device Tree Clock bindings for arch-vt8500 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "via,vt8500-pll-clock" - for a VT8500/WM8505 PLL clock + "wm,wm8650-pll-clock" - for a WM8650 PLL clock + "via,vt8500-device-clock" - for a VT/WM device clock + +Required properties for PLL clocks: +- reg : shall be the control register offset from PMC base for the pll clock. +- clocks : shall be the input parent clock phandle for the clock. This should + be the reference clock. +- #clock-cells : from common clock binding; shall be set to 0. + +Required properties for device clocks: +- clocks : shall be the input parent clock phandle for the clock. This should + be a pll output. +- #clock-cells : from common clock binding; shall be set to 0. + + +Device Clocks + +Device clocks are required to have one or both of the following sets of +properties: + + +Gated device clocks: + +Required properties: +- enable-reg : shall be the register offset from PMC base for the enable + register. +- enable-bit : shall be the bit within enable-reg to enable/disable the clock. + + +Divisor device clocks: + +Required property: +- divisor-reg : shall be the register offset from PMC base for the divisor + register. +Optional property: +- divisor-mask : shall be the mask for the divisor register. Defaults to 0x1f + if not specified. + + +For example: + +ref25: ref25M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; +}; + +plla: plla { + #clock-cells = <0>; + compatible = "wm,wm8650-pll-clock"; + clocks = <&ref25>; + reg = <0x200>; +}; + +sdhc: sdhc { + #clock-cells = <0>; + compatible = "via,vt8500-device-clock"; + clocks = <&pllb>; + divisor-reg = <0x328>; + divisor-mask = <0x3f>; + enable-reg = <0x254>; + enable-bit = <18>; +}; diff --git a/Documentation/devicetree/bindings/dma/mmp-dma.txt b/Documentation/devicetree/bindings/dma/mmp-dma.txt new file mode 100644 index 00000000000..a4fa4efa1d8 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mmp-dma.txt @@ -0,0 +1,74 @@ +* MARVELL MMP DMA controller + +Marvell Peripheral DMA Controller +Used platfroms: pxa688, pxa910, pxa3xx, etc + +Required properties: +- compatible: Should be "marvell,pdma-1.0" +- reg: Should contain DMA registers location and length. +- interrupts: Either contain all of the per-channel DMA interrupts + or one irq for pdma device +- #dma-channels: Number of DMA channels supported by the controller. + +"marvell,pdma-1.0" +Used platfroms: pxa25x, pxa27x, pxa3xx, pxa93x, pxa168, pxa910, pxa688. + +Examples: + +/* + * Each channel has specific irq + * ICU parse out irq channel from ICU register, + * while DMA controller may not able to distinguish the irq channel + * Using this method, interrupt-parent is required as demuxer + * For example, pxa688 icu register 0x128, bit 0~15 is PDMA channel irq, + * 18~21 is ADMA irq + */ +pdma: dma-controller@d4000000 { + compatible = "marvell,pdma-1.0"; + reg = <0xd4000000 0x10000>; + interrupts = <0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15>; + interrupt-parent = <&intcmux32>; + #dma-channels = <16>; + }; + +/* + * One irq for all channels + * Dmaengine driver (DMA controller) distinguish irq channel via + * parsing internal register + */ +pdma: dma-controller@d4000000 { + compatible = "marvell,pdma-1.0"; + reg = <0xd4000000 0x10000>; + interrupts = <47>; + #dma-channels = <16>; + }; + + +Marvell Two Channel DMA Controller used specifically for audio +Used platfroms: pxa688, pxa910 + +Required properties: +- compatible: Should be "marvell,adma-1.0" or "marvell,pxa910-squ" +- reg: Should contain DMA registers location and length. +- interrupts: Either contain all of the per-channel DMA interrupts + or one irq for dma device + +"marvell,adma-1.0" used on pxa688 +"marvell,pxa910-squ" used on pxa910 + +Examples: + +/* each channel has specific irq */ +adma0: dma-controller@d42a0800 { + compatible = "marvell,adma-1.0"; + reg = <0xd42a0800 0x100>; + interrupts = <18 19>; + interrupt-parent = <&intcmux32>; + }; + +/* One irq for all channels */ +squ: dma-controller@d42a0800 { + compatible = "marvell,pxa910-squ"; + reg = <0xd42a0800 0x100>; + interrupts = <46>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt index 5375625e8cd..f1e5dfecf55 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -39,3 +39,46 @@ Example: #gpio-cells = <4>; gpio-controller; }; + + +Samsung S3C24XX GPIO Controller + +Required properties: +- compatible: Compatible property value should be "samsung,s3c24xx-gpio". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual. + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + + Values for gpio specifier: + - Pin number: depending on the controller a number from 0 up to 15. + - Mux function: Depending on the SoC and the gpio bank the gpio can be set + as input, output or a special function + - Flags and Pull Up/Down: the values to use differ for the individual SoCs + example S3C2416/S3C2450: + 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 2 - Pull Up Enabled. + Bit 16 (0x00010000) - Input is active low. + Consult the user manual for the correct values of Mux and Pull Up/Down. + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1. + +Example: + + gpa: gpio-controller@56000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,s3c24xx-gpio"; + reg = <0x56000000 0x10>; + #gpio-cells = <3>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt index 16695d9cf1e..66788fda1db 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt @@ -11,6 +11,11 @@ Required properties: - interrupt-controller: Mark the device node as an interrupt controller The first cell is the GPIO number. The second cell is not used. +- ti,use-leds : Enables LEDA and LEDB outputs if set +- ti,debounce : if n-th bit is set, debounces GPIO-n +- ti,mmc-cd : if n-th bit is set, GPIO-n controls VMMC(n+1) +- ti,pullups : if n-th bit is set, set a pullup on GPIO-n +- ti,pulldowns : if n-th bit is set, set a pulldown on GPIO-n Example: @@ -20,4 +25,5 @@ twl_gpio: gpio { gpio-controller; #interrupt-cells = <2>; interrupt-controller; + ti,use-leds; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt b/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt new file mode 100644 index 00000000000..f4dc5233167 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt @@ -0,0 +1,24 @@ +VIA/Wondermedia VT8500 GPIO Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-gpio", "wm,wm8505-gpio" + or "wm,wm8650-gpio" depending on your SoC +- reg : Should contain 1 register range (address and length) +- #gpio-cells : should be <3>. + 1) bank + 2) pin number + 3) flags - should be 0 + +Example: + + gpio: gpio-controller@d8110000 { + compatible = "via,vt8500-gpio"; + gpio-controller; + reg = <0xd8110000 0x10000>; + #gpio-cells = <3>; + }; + + vibrate { + gpios = <&gpio 0 1 0>; /* Bank 0, Pin 1, No flags */ + }; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 1a85f986961..2f5322b119e 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -56,3 +56,4 @@ stm,m41t00 Serial Access TIMEKEEPER stm,m41t62 Serial real-time clock (RTC) with alarm stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS ti,tsc2003 I2C Touch-Screen Controller +ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt new file mode 100644 index 00000000000..548892c08c5 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt @@ -0,0 +1,110 @@ +BCM2835 Top-Level ("ARMCTRL") Interrupt Controller + +The BCM2835 contains a custom top-level interrupt controller, which supports +72 interrupt sources using a 2-level register scheme. The interrupt +controller, or the HW block containing it, is referred to occasionally +as "armctrl" in the SoC documentation, hence naming of this binding. + +Required properties: + +- compatible : should be "brcm,bcm2835-armctrl-ic.txt" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 2. + + The 1st cell is the interrupt bank; 0 for interrupts in the "IRQ basic + pending" register, or 1/2 respectively for interrupts in the "IRQ pending + 1/2" register. + + The 2nd cell contains the interrupt number within the bank. Valid values + are 0..7 for bank 0, and 0..31 for bank 1. + +The interrupt sources are as follows: + +Bank 0: +0: ARM_TIMER +1: ARM_MAILBOX +2: ARM_DOORBELL_0 +3: ARM_DOORBELL_1 +4: VPU0_HALTED +5: VPU1_HALTED +6: ILLEGAL_TYPE0 +7: ILLEGAL_TYPE1 + +Bank 1: +0: TIMER0 +1: TIMER1 +2: TIMER2 +3: TIMER3 +4: CODEC0 +5: CODEC1 +6: CODEC2 +7: VC_JPEG +8: ISP +9: VC_USB +10: VC_3D +11: TRANSPOSER +12: MULTICORESYNC0 +13: MULTICORESYNC1 +14: MULTICORESYNC2 +15: MULTICORESYNC3 +16: DMA0 +17: DMA1 +18: VC_DMA2 +19: VC_DMA3 +20: DMA4 +21: DMA5 +22: DMA6 +23: DMA7 +24: DMA8 +25: DMA9 +26: DMA10 +27: DMA11 +28: DMA12 +29: AUX +30: ARM +31: VPUDMA + +Bank 2: +0: HOSTPORT +1: VIDEOSCALER +2: CCP2TX +3: SDC +4: DSI0 +5: AVE +6: CAM0 +7: CAM1 +8: HDMI0 +9: HDMI1 +10: PIXELVALVE1 +11: I2CSPISLV +12: DSI1 +13: PWA0 +14: PWA1 +15: CPR +16: SMI +17: GPIO0 +18: GPIO1 +19: GPIO2 +20: GPIO3 +21: VC_I2C +22: VC_SPI +23: VC_I2SPCM +24: VC_SDIO +25: VC_UART +26: SLIMBUS +27: VEC +28: CPG +29: RNG +30: VC_ARASANSDIO +31: AVSPMON + +Example: + +intc: interrupt-controller { + compatible = "brcm,bcm2835-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt b/Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt new file mode 100644 index 00000000000..9ceb19e0c7f --- /dev/null +++ b/Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt @@ -0,0 +1,52 @@ +* AC timing parameters of LPDDR2(JESD209-2) memories for a given speed-bin + +Required properties: +- compatible : Should be "jedec,lpddr2-timings" +- min-freq : minimum DDR clock frequency for the speed-bin. Type is <u32> +- max-freq : maximum DDR clock frequency for the speed-bin. Type is <u32> + +Optional properties: + +The following properties represent AC timing parameters from the memory +data-sheet of the device for a given speed-bin. All these properties are +of type <u32> and the default unit is ps (pico seconds). Parameters with +a different unit have a suffix indicating the unit such as 'tRAS-max-ns' +- tRCD +- tWR +- tRAS-min +- tRRD +- tWTR +- tXP +- tRTP +- tDQSCK-max +- tFAW +- tZQCS +- tZQinit +- tRPab +- tZQCL +- tCKESR +- tRAS-max-ns +- tDQSCK-max-derated + +Example: + +timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 { + compatible = "jedec,lpddr2-timings"; + min-freq = <10000000>; + max-freq = <400000000>; + tRPab = <21000>; + tRCD = <18000>; + tWR = <15000>; + tRAS-min = <42000>; + tRRD = <10000>; + tWTR = <7500>; + tXP = <7500>; + tRTP = <7500>; + tCKESR = <15000>; + tDQSCK-max = <5500>; + tFAW = <50000>; + tZQCS = <90000>; + tZQCL = <360000>; + tZQinit = <1000000>; + tRAS-max-ns = <70000>; +}; diff --git a/Documentation/devicetree/bindings/lpddr2/lpddr2.txt b/Documentation/devicetree/bindings/lpddr2/lpddr2.txt new file mode 100644 index 00000000000..58354a075e1 --- /dev/null +++ b/Documentation/devicetree/bindings/lpddr2/lpddr2.txt @@ -0,0 +1,102 @@ +* LPDDR2 SDRAM memories compliant to JEDEC JESD209-2 + +Required properties: +- compatible : Should be one of - "jedec,lpddr2-nvm", "jedec,lpddr2-s2", + "jedec,lpddr2-s4" + + "ti,jedec-lpddr2-s2" should be listed if the memory part is LPDDR2-S2 type + + "ti,jedec-lpddr2-s4" should be listed if the memory part is LPDDR2-S4 type + + "ti,jedec-lpddr2-nvm" should be listed if the memory part is LPDDR2-NVM type + +- density : <u32> representing density in Mb (Mega bits) + +- io-width : <u32> representing bus width. Possible values are 8, 16, and 32 + +Optional properties: + +The following optional properties represent the minimum value of some AC +timing parameters of the DDR device in terms of number of clock cycles. +These values shall be obtained from the device data-sheet. +- tRRD-min-tck +- tWTR-min-tck +- tXP-min-tck +- tRTP-min-tck +- tCKE-min-tck +- tRPab-min-tck +- tRCD-min-tck +- tWR-min-tck +- tRASmin-min-tck +- tCKESR-min-tck +- tFAW-min-tck + +Child nodes: +- The lpddr2 node may have one or more child nodes of type "lpddr2-timings". + "lpddr2-timings" provides AC timing parameters of the device for + a given speed-bin. The user may provide the timings for as many + speed-bins as is required. Please see Documentation/devicetree/ + bindings/lpddr2/lpddr2-timings.txt for more information on "lpddr2-timings" + +Example: + +elpida_ECB240ABACN : lpddr2 { + compatible = "Elpida,ECB240ABACN","jedec,lpddr2-s4"; + density = <2048>; + io-width = <32>; + + tRPab-min-tck = <3>; + tRCD-min-tck = <3>; + tWR-min-tck = <3>; + tRASmin-min-tck = <3>; + tRRD-min-tck = <2>; + tWTR-min-tck = <2>; + tXP-min-tck = <2>; + tRTP-min-tck = <2>; + tCKE-min-tck = <3>; + tCKESR-min-tck = <3>; + tFAW-min-tck = <8>; + + timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 { + compatible = "jedec,lpddr2-timings"; + min-freq = <10000000>; + max-freq = <400000000>; + tRPab = <21000>; + tRCD = <18000>; + tWR = <15000>; + tRAS-min = <42000>; + tRRD = <10000>; + tWTR = <7500>; + tXP = <7500>; + tRTP = <7500>; + tCKESR = <15000>; + tDQSCK-max = <5500>; + tFAW = <50000>; + tZQCS = <90000>; + tZQCL = <360000>; + tZQinit = <1000000>; + tRAS-max-ns = <70000>; + }; + + timings_elpida_ECB240ABACN_200mhz: lpddr2-timings@1 { + compatible = "jedec,lpddr2-timings"; + min-freq = <10000000>; + max-freq = <200000000>; + tRPab = <21000>; + tRCD = <18000>; + tWR = <15000>; + tRAS-min = <42000>; + tRRD = <10000>; + tWTR = <10000>; + tXP = <7500>; + tRTP = <7500>; + tCKESR = <15000>; + tDQSCK-max = <5500>; + tFAW = <50000>; + tZQCS = <90000>; + tZQCL = <360000>; + tZQinit = <1000000>; + tRAS-max-ns = <70000>; + }; + +} diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt new file mode 100644 index 00000000000..0604d42f38d --- /dev/null +++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt @@ -0,0 +1,30 @@ +* Samsung Exynos5 G-Scaler device + +G-Scaler is used for scaling and color space conversion on EXYNOS5 SoCs. + +Required properties: +- compatible: should be "samsung,exynos5-gsc" +- reg: should contain G-Scaler physical address location and length. +- interrupts: should contain G-Scaler interrupt number + +Example: + +gsc_0: gsc@0x13e00000 { + compatible = "samsung,exynos5-gsc"; + reg = <0x13e00000 0x1000>; + interrupts = <0 85 0>; +}; + +Aliases: +Each G-Scaler node should have a numbered alias in the aliases node, +in the form of gscN, N = 0...3. G-Scaler driver uses these aliases +to retrieve the device IDs using "of_alias_get_id()" call. + +Example: + +aliases { + gsc0 =&gsc_0; + gsc1 =&gsc_1; + gsc2 =&gsc_2; + gsc3 =&gsc_3; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt new file mode 100644 index 00000000000..938f8e1ba20 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt @@ -0,0 +1,55 @@ +* EMIF family of TI SDRAM controllers + +EMIF - External Memory Interface - is an SDRAM controller used in +TI SoCs. EMIF supports, based on the IP revision, one or more of +DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance +of the EMIF IP and memory parts attached to it. + +Required properties: +- compatible : Should be of the form "ti,emif-<ip-rev>" where <ip-rev> + is the IP revision of the specific EMIF instance. + +- phy-type : <u32> indicating the DDR phy type. Following are the + allowed values + <1> : Attila PHY + <2> : Intelli PHY + +- device-handle : phandle to a "lpddr2" node representing the memory part + +- ti,hwmods : For TI hwmods processing and omap device creation + the value shall be "emif<n>" where <n> is the number of the EMIF + instance with base 1. + +Optional properties: +- cs1-used : Have this property if CS1 of this EMIF + instance has a memory part attached to it. If there is a memory + part attached to CS1, it should be the same type as the one on CS0, + so there is no need to give the details of this memory part. + +- cal-resistor-per-cs : Have this property if the board has one + calibration resistor per chip-select. + +- hw-caps-read-idle-ctrl: Have this property if the controller + supports read idle window programming + +- hw-caps-dll-calib-ctrl: Have this property if the controller + supports dll calibration control + +- hw-caps-ll-interface : Have this property if the controller + has a low latency interface and corresponding interrupt events + +- hw-caps-temp-alert : Have this property if the controller + has capability for generating SDRAM temperature alerts + +Example: + +emif1: emif@0x4c000000 { + compatible = "ti,emif-4d"; + ti,hwmods = "emif2"; + phy-type = <1>; + device-handle = <&elpida_ECB240ABACN>; + cs1-used; + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; +}; diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt index 69e757a657a..ce83c8d3c00 100644 --- a/Documentation/devicetree/bindings/mfd/ab8500.txt +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -23,6 +23,7 @@ Device IRQ Names Supply Names Description ab8500-bm : : : Battery Manager ab8500-btemp : : : Battery Temperature ab8500-charger : : : Battery Charger +ab8500-codec : : : Audio Codec ab8500-fg : : : Fuel Gauge ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter SW_CONV_END : : @@ -52,6 +53,14 @@ Optional child device properties: supplied in the interrupts property - <supply_name>-supply : contains a phandle to the regulator supply node in Device Tree +Non-standard child device properties: + - Audio CODEC: + - stericsson,amic[1|2]-type-single-ended : Single-ended Analoge Mic (default: differential) + - stericsson,amic1a-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,amic1b-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,amic2-bias-vamic1 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,earpeice-cmv : Earpeice voltage (only: 950 | 1100 | 1270 | 1580) + ab8500@5 { compatible = "stericsson,ab8500"; reg = <5>; /* mailbox 5 is i2c */ @@ -110,6 +119,12 @@ ab8500@5 { compatible = "stericsson,ab8500-pwm"; }; + codec: ab8500-codec { + compatible = "stericsson,ab8500-codec"; + + stericsson,earpeice-cmv = <950>; /* Units in mV. */ + }; + ab8500-regulators { compatible = "stericsson,ab8500-regulator"; diff --git a/Documentation/devicetree/bindings/misc/at25.txt b/Documentation/devicetree/bindings/misc/at25.txt index ab3c327929d..1d3447165c3 100644 --- a/Documentation/devicetree/bindings/misc/at25.txt +++ b/Documentation/devicetree/bindings/misc/at25.txt @@ -1,21 +1,35 @@ -Atmel AT25 eeprom +EEPROMs (SPI) compatible with Atmel at25. Required properties: - compatible : "atmel,at25". - reg : chip select number - spi-max-frequency : max spi frequency to use +- pagesize : size of the eeprom page +- size : total eeprom size in bytes +- address-width : number of address bits (one of 8, 16, or 24) +Optional properties: +- spi-cpha : SPI shifted clock phase, as per spi-bus bindings. +- spi-cpol : SPI inverse clock polarity, as per spi-bus bindings. +- read-only : this parameter-less property disables writes to the eeprom + +Obsolete legacy properties are can be used in place of "size", "pagesize", +"address-width", and "read-only": - at25,byte-len : total eeprom size in bytes - at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h - at25,page-size : size of the eeprom page -Examples: -at25@0 { - compatible = "atmel,at25"; - reg = <0> - spi-max-frequency = <5000000>; +Additional compatible properties are also allowed. + +Example: + at25@0 { + compatible = "atmel,at25", "st,m95256"; + reg = <0> + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; - at25,byte-len = <0x8000>; - at25,addr-mode = <2>; - at25,page-size = <64>; -}; + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; diff --git a/Documentation/devicetree/bindings/misc/lis302.txt b/Documentation/devicetree/bindings/misc/lis302.txt new file mode 100644 index 00000000000..6def86f6b05 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/lis302.txt @@ -0,0 +1,112 @@ +LIS302 accelerometer devicetree bindings + +This device is matched via its bus drivers, and has a number of properties +that apply in on the generic device (independent from the bus). + + +Required properties for the SPI bindings: + - compatible: should be set to "st,lis3lv02d_spi" + - reg: the chipselect index + - spi-max-frequency: maximal bus speed, should be set to 1000000 unless + constrained by external circuitry + - interrupts: the interrupt generated by the device + +Required properties for the I2C bindings: + - compatible: should be set to "st,lis3lv02d" + - reg: i2c slave address + - Vdd-supply: The input supply for Vdd + - Vdd_IO-supply: The input supply for Vdd_IO + + +Optional properties for all bus drivers: + + - st,click-single-{x,y,z}: if present, tells the device to issue an + interrupt on single click events on the + x/y/z axis. + - st,click-double-{x,y,z}: if present, tells the device to issue an + interrupt on double click events on the + x/y/z axis. + - st,click-thresh-{x,y,z}: set the x/y/z axis threshold + - st,click-click-time-limit: click time limit, from 0 to 127.5msec + with step of 0.5 msec + - st,click-latency: click latency, from 0 to 255 msec with + step of 1 msec. + - st,click-window: click window, from 0 to 255 msec with + step of 1 msec. + - st,irq{1,2}-disable: disable IRQ 1/2 + - st,irq{1,2}-ff-wu-1: raise IRQ 1/2 on FF_WU_1 condition + - st,irq{1,2}-ff-wu-2: raise IRQ 1/2 on FF_WU_2 condition + - st,irq{1,2}-data-ready: raise IRQ 1/2 on data ready contition + - st,irq{1,2}-click: raise IRQ 1/2 on click condition + - st,irq-open-drain: consider IRQ lines open-drain + - st,irq-active-low: make IRQ lines active low + - st,wu-duration-1: duration register for Free-Fall/Wake-Up + interrupt 1 + - st,wu-duration-2: duration register for Free-Fall/Wake-Up + interrupt 2 + - st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for + upper/lower limit + - st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of + highpass cut-off frequency + - st,hipass{1,2}-disable: disable highpass 1/2. + - st,default-rate=: set the default rate + - st,axis-{x,y,z}=: set the axis to map to the three coordinates + - st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis + (used by self-test) + + +Example for a SPI device node: + + lis302@0 { + compatible = "st,lis302dl-spi"; + reg = <0>; + spi-max-frequency = <1000000>; + interrupt-parent = <&gpio>; + interrupts = <104 0>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + }; + +Example for a I2C device node: + + lis331dlh: lis331dlh@18 { + compatible = "st,lis331dlh", "st,lis3lv02d"; + reg = <0x18>; + Vdd-supply = <&lis3_reg>; + Vdd_IO-supply = <&lis3_reg>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + st,min-limit-x = <120>; + st,min-limit-y = <120>; + st,min-limit-z = <140>; + st,max-limit-x = <550>; + st,max-limit-y = <550>; + st,max-limit-z = <750>; + }; + diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 70cd49b1caa..1dd622546d0 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -10,8 +10,8 @@ Required properties: - compatible : Should be "fsl,<chip>-esdhc" Optional properties: -- fsl,cd-internal : Indicate to use controller internal card detection -- fsl,wp-internal : Indicate to use controller internal write protection +- fsl,cd-controller : Indicate to use controller internal card detection +- fsl,wp-controller : Indicate to use controller internal write protection Examples: @@ -19,8 +19,8 @@ esdhc@70004000 { compatible = "fsl,imx51-esdhc"; reg = <0x70004000 0x4000>; interrupts = <1>; - fsl,cd-internal; - fsl,wp-internal; + fsl,cd-controller; + fsl,wp-controller; }; esdhc@70008000 { diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt new file mode 100644 index 00000000000..f1421e2bbab --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt @@ -0,0 +1,31 @@ +PXA3xx NAND DT bindings + +Required properties: + + - compatible: Should be "marvell,pxa3xx-nand" + - reg: The register base for the controller + - interrupts: The interrupt to map + - #address-cells: Set to <1> if the node includes partitions + +Optional properties: + + - marvell,nand-enable-arbiter: Set to enable the bus arbiter + - marvell,nand-keep-config: Set to keep the NAND controller config as set + by the bootloader + - num-cs: Number of chipselect lines to usw + +Example: + + nand0: nand@43100000 { + compatible = "marvell,pxa3xx-nand"; + reg = <0x43100000 90>; + interrupts = <45>; + #address-cells = <1>; + + marvell,nand-enable-arbiter; + marvell,nand-keep-config; + num-cs = <1>; + + /* partitions (optional) */ + }; + diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt new file mode 100644 index 00000000000..8f1ae81228e --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/c_can.txt @@ -0,0 +1,49 @@ +Bosch C_CAN/D_CAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "bosch,c_can" for C_CAN controllers and + "bosch,d_can" for D_CAN controllers. +- reg : physical base address and size of the C_CAN/D_CAN + registers map +- interrupts : property with a value describing the interrupt + number + +Optional properties: +- ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the + instance number + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Example: + +Step1: SoC common .dtsi file + + dcan1: d_can@481d0000 { + compatible = "bosch,d_can"; + reg = <0x481d0000 0x2000>; + interrupts = <55>; + interrupt-parent = <&intc>; + status = "disabled"; + }; + +(or) + + dcan1: d_can@481d0000 { + compatible = "bosch,d_can"; + ti,hwmods = "d_can1"; + reg = <0x481d0000 0x2000>; + interrupts = <55>; + interrupt-parent = <&intc>; + status = "disabled"; + }; + +Step 2: board specific .dts file + + &dcan1 { + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt new file mode 100644 index 00000000000..dcaabe9fe86 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -0,0 +1,109 @@ +TI SoC Ethernet Switch Controller Device Tree Bindings +------------------------------------------------------ + +Required properties: +- compatible : Should be "ti,cpsw" +- reg : physical base address and size of the cpsw + registers map +- interrupts : property with a value describing the interrupt + number +- interrupt-parent : The parent interrupt controller +- cpdma_channels : Specifies number of channels in CPDMA +- host_port_no : Specifies host port shift +- cpdma_reg_ofs : Specifies CPDMA submodule register offset +- cpdma_sram_ofs : Specifies CPDMA SRAM offset +- ale_reg_ofs : Specifies ALE submodule register offset +- ale_entries : Specifies No of entries ALE can hold +- host_port_reg_ofs : Specifies host port register offset +- hw_stats_reg_ofs : Specifies hardware statistics register offset +- bd_ram_ofs : Specifies internal desciptor RAM offset +- bd_ram_size : Specifies internal descriptor RAM size +- rx_descs : Specifies number of Rx descriptors +- mac_control : Specifies Default MAC control register content + for the specific platform +- slaves : Specifies number for slaves +- slave_reg_ofs : Specifies slave register offset +- sliver_reg_ofs : Specifies slave sliver register offset +- phy_id : Specifies slave phy id +- mac-address : Specifies slave MAC address + +Optional properties: +- ti,hwmods : Must be "cpgmac0" +- no_bd_ram : Must be 0 or 1 + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples: + + mac: ethernet@4A100000 { + compatible = "ti,cpsw"; + reg = <0x4A100000 0x1000>; + interrupts = <55 0x4>; + interrupt-parent = <&intc>; + cpdma_channels = <8>; + host_port_no = <0>; + cpdma_reg_ofs = <0x800>; + cpdma_sram_ofs = <0xa00>; + ale_reg_ofs = <0xd00>; + ale_entries = <1024>; + host_port_reg_ofs = <0x108>; + hw_stats_reg_ofs = <0x900>; + bd_ram_ofs = <0x2000>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + cpsw_emac0: slave@0 { + slave_reg_ofs = <0x208>; + sliver_reg_ofs = <0xd80>; + phy_id = "davinci_mdio.16:00"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + cpsw_emac1: slave@1 { + slave_reg_ofs = <0x308>; + sliver_reg_ofs = <0xdc0>; + phy_id = "davinci_mdio.16:01"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; + +(or) + mac: ethernet@4A100000 { + compatible = "ti,cpsw"; + ti,hwmods = "cpgmac0"; + cpdma_channels = <8>; + host_port_no = <0>; + cpdma_reg_ofs = <0x800>; + cpdma_sram_ofs = <0xa00>; + ale_reg_ofs = <0xd00>; + ale_entries = <1024>; + host_port_reg_ofs = <0x108>; + hw_stats_reg_ofs = <0x900>; + bd_ram_ofs = <0x2000>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + cpsw_emac0: slave@0 { + slave_reg_ofs = <0x208>; + sliver_reg_ofs = <0xd80>; + phy_id = "davinci_mdio.16:00"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + cpsw_emac1: slave@1 { + slave_reg_ofs = <0x308>; + sliver_reg_ofs = <0xdc0>; + phy_id = "davinci_mdio.16:01"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt new file mode 100644 index 00000000000..72efaaf764f --- /dev/null +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -0,0 +1,33 @@ +TI SoC Davinci MDIO Controller Device Tree Bindings +--------------------------------------------------- + +Required properties: +- compatible : Should be "ti,davinci_mdio" +- reg : physical base address and size of the davinci mdio + registers map +- bus_freq : Mdio Bus frequency + +Optional properties: +- ti,hwmods : Must be "davinci_mdio" + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples: + + mdio: davinci_mdio@4A101000 { + compatible = "ti,cpsw"; + reg = <0x4A101000 0x1000>; + bus_freq = <1000000>; + }; + +(or) + + mdio: davinci_mdio@4A101000 { + compatible = "ti,cpsw"; + ti,hwmods = "davinci_mdio"; + bus_freq = <1000000>; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt new file mode 100644 index 00000000000..8516929c725 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt @@ -0,0 +1,75 @@ +Properties for an MDIO bus multiplexer controlled by a memory-mapped device + +This is a special case of a MDIO bus multiplexer. A memory-mapped device, +like an FPGA, is used to control which child bus is connected. The mdio-mux +node must be a child of the memory-mapped device. The driver currently only +supports devices with eight-bit registers. + +Required properties in addition to the generic multiplexer properties: + +- compatible : string, must contain "mdio-mux-mmioreg" + +- reg : integer, contains the offset of the register that controls the bus + multiplexer. The size field in the 'reg' property is the size of + register, and must therefore be 1. + +- mux-mask : integer, contains an eight-bit mask that specifies which + bits in the register control the actual bus multiplexer. The + 'reg' property of each child mdio-mux node must be constrained by + this mask. + +Example: + +The FPGA node defines a memory-mapped FPGA with a register space of 0x30 bytes. +For the "EMI2" MDIO bus, register 9 (BRDCFG1) controls the mux on that bus. +A bitmask of 0x6 means that bits 1 and 2 (bit 0 is lsb) are the bits on +BRDCFG1 that control the actual mux. + + /* The FPGA node */ + fpga: board-control@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; + ranges = <0 3 0 0x30>; + + mdio-mux-emi2 { + compatible = "mdio-mux-mmioreg", "mdio-mux"; + mdio-parent-bus = <&xmdio0>; + #address-cells = <1>; + #size-cells = <0>; + reg = <9 1>; // BRDCFG1 + mux-mask = <0x6>; // EMI2 + + emi2_slot1: mdio@0 { // Slot 1 XAUI (FM2) + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot1: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <4>; + }; + }; + + emi2_slot2: mdio@2 { // Slot 2 XAUI (FM1) + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot2: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + }; + }; + }; + }; + + /* The parent MDIO bus. */ + xmdio0: mdio@f1000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,fman-xmdio"; + reg = <0xf1000 0x1000>; + interrupts = <100 1 0 0>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt new file mode 100644 index 00000000000..03dee50532f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -0,0 +1,196 @@ +Samsung GPIO and Pin Mux/Config controller + +Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware +controller. It controls the input/output settings on the available pads/pins +and also provides ability to multiplex and configure the output of various +on-chip controllers onto these pads. + +Required Properties: +- compatible: should be one of the following. + - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller. + - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller. + +- reg: Base address of the pin controller hardware module and length of + the address space it occupies. + +- interrupts: interrupt specifier for the controller. The format and value of + the interrupt specifier depends on the interrupt parent for the controller. + +- Pin mux/config groups as child nodes: The pin mux (selecting pin function + mode) and pin config (pull up/down, driver strength) settings are represented + as child nodes of the pin-controller node. There should be atleast one + child node and there is no limit on the count of these child nodes. + + The child node should contain a list of pin(s) on which a particular pin + function selection or pin configuration (or both) have to applied. This + list of pins is specified using the property name "samsung,pins". There + should be atleast one pin specfied for this property and there is no upper + limit on the count of pins that can be specified. The pins are specified + using pin names which are derived from the hardware manual of the SoC. As + an example, the pins in GPA0 bank of the pin controller can be represented + as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case. + The format of the pin names should be (as per the hardware manual) + "[pin bank name]-[pin number within the bank]". + + The pin function selection that should be applied on the pins listed in the + child node is specified using the "samsung,pin-function" property. The value + of this property that should be applied to each of the pins listed in the + "samsung,pins" property should be picked from the hardware manual of the SoC + for the specified pin group. This property is optional in the child node if + no specific function selection is desired for the pins listed in the child + node. The value of this property is used as-is to program the pin-controller + function selector register of the pin-bank. + + The child node can also optionally specify one or more of the pin + configuration that should be applied on all the pins listed in the + "samsung,pins" property of the child node. The following pin configuration + properties are supported. + + - samsung,pin-pud: Pull up/down configuration. + - samsung,pin-drv: Drive strength configuration. + - samsung,pin-pud-pdn: Pull up/down configuration in power down mode. + - samsung,pin-drv-pdn: Drive strength configuration in power down mode. + + The values specified by these config properties should be derived from the + hardware manual and these values are programmed as-is into the pin + pull up/down and driver strength register of the pin-controller. + + Note: A child should include atleast a pin function selection property or + pin configuration property (one or more) or both. + + The client nodes that require a particular pin function selection and/or + pin configuration should use the bindings listed in the "pinctrl-bindings.txt" + file. + +External GPIO and Wakeup Interrupts: + +The controller supports two types of external interrupts over gpio. The first +is the external gpio interrupt and second is the external wakeup interrupts. +The difference between the two is that the external wakeup interrupts can be +used as system wakeup events. + +A. External GPIO Interrupts: For supporting external gpio interrupts, the + following properties should be specified in the pin-controller device node. + +- interrupt-controller: identifies the controller node as interrupt-parent. +- #interrupt-cells: the value of this property should be 2. + - First Cell: represents the external gpio interrupt number local to the + external gpio interrupt space of the controller. + - Second Cell: flags to identify the type of the interrupt + - 1 = rising edge triggered + - 2 = falling edge triggered + - 3 = rising and falling edge triggered + - 4 = high level triggered + - 8 = low level triggered + +B. External Wakeup Interrupts: For supporting external wakeup interrupts, a + child node representing the external wakeup interrupt controller should be + included in the pin-controller device node. This child node should include + the following properties. + + - compatible: identifies the type of the external wakeup interrupt controller + The possible values are: + - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller + found on Samsung Exynos4210 SoC. + - interrupt-parent: phandle of the interrupt parent to which the external + wakeup interrupts are forwarded to. + - interrupt-controller: identifies the node as interrupt-parent. + - #interrupt-cells: the value of this property should be 2 + - First Cell: represents the external wakeup interrupt number local to + the external wakeup interrupt space of the controller. + - Second Cell: flags to identify the type of the interrupt + - 1 = rising edge triggered + - 2 = falling edge triggered + - 3 = rising and falling edge triggered + - 4 = high level triggered + - 8 = low level triggered + +Aliases: + +All the pin controller nodes should be represented in the aliases node using +the following format 'pinctrl{n}' where n is a unique number for the alias. + +Example 1: A pin-controller node with pin groups. + + pinctrl_0: pinctrl@11400000 { + compatible = "samsung,pinctrl-exynos4210"; + reg = <0x11400000 0x1000>; + interrupts = <0 47 0>; + + uart0_data: uart0-data { + samsung,pins = "gpa0-0", "gpa0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + uart0_fctl: uart0-fctl { + samsung,pins = "gpa0-2", "gpa0-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + uart1_data: uart1-data { + samsung,pins = "gpa0-4", "gpa0-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + uart1_fctl: uart1-fctl { + samsung,pins = "gpa0-6", "gpa0-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + i2c2_bus: i2c2-bus { + samsung,pins = "gpa0-6", "gpa0-7"; + samsung,pin-function = <3>; + samsung,pin-pud = <3>; + samsung,pin-drv = <0>; + }; + }; + +Example 2: A pin-controller node with external wakeup interrupt controller node. + + pinctrl_1: pinctrl@11000000 { + compatible = "samsung,pinctrl-exynos4210"; + reg = <0x11000000 0x1000>; + interrupts = <0 46 0>; + interrupt-controller; + #interrupt-cells = <2>; + + wakup_eint: wakeup-interrupt-controller { + compatible = "samsung,exynos4210-wakeup-eint"; + interrupt-parent = <&gic>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>, + <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>, + <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>, + <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>, + <0 32 0>; + }; + }; + +Example 3: A uart client node that supports 'default' and 'flow-control' states. + + uart@13800000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x13800000 0x100>; + interrupts = <0 52 0>; + pinctrl-names = "default", "flow-control; + pinctrl-0 = <&uart0_data>; + pinctrl-1 = <&uart0_data &uart0_fctl>; + }; + +Example 4: Set up the default pin state for uart controller. + + static int s3c24xx_serial_probe(struct platform_device *pdev) { + struct pinctrl *pinctrl; + ... + ... + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); + } diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 66ece3f87bb..ecfc6ccd67e 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -11,10 +11,13 @@ Optional properties: - regulator-boot-on: bootloader/firmware enabled regulator - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) + +Deprecated properties: - regulator-compatible: If a regulator chip contains multiple regulators, and if the chip's binding contains a child node that describes each regulator, then this property indicates which regulator - this child node is intended to configure. + this child node is intended to configure. If this property is missing, + the node's name will be used instead. Example: diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index 0487e9675ba..d316fb895da 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -22,66 +22,49 @@ Example: compatible = "ti,tps65217"; regulators { - #address-cells = <1>; - #size-cells = <0>; - - dcdc1_reg: regulator@0 { - reg = <0>; - regulator-compatible = "dcdc1"; + dcdc1_reg: dcdc1 { regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; regulator-boot-on; regulator-always-on; }; - dcdc2_reg: regulator@1 { - reg = <1>; - regulator-compatible = "dcdc2"; + dcdc2_reg: dcdc2 { regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; - dcdc3_reg: regulator@2 { - reg = <2>; - regulator-compatible = "dcdc3"; + dcdc3_reg: dcc3 { regulator-min-microvolt = <900000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - ldo1_reg: regulator@3 { - reg = <3>; - regulator-compatible = "ldo1"; + ldo1_reg: ldo1 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; - ldo2_reg: regulator@4 { - reg = <4>; - regulator-compatible = "ldo2"; + ldo2_reg: ldo2 { regulator-min-microvolt = <900000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; - ldo3_reg: regulator@5 { - reg = <5>; - regulator-compatible = "ldo3"; + ldo3_reg: ldo3 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; - ldo4_reg: regulator@6 { - reg = <6>; - regulator-compatible = "ldo4"; + ldo4_reg: ldo4 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; diff --git a/Documentation/devicetree/bindings/regulator/tps6586x.txt b/Documentation/devicetree/bindings/regulator/tps6586x.txt index d156e1b5db1..07b9ef6e49d 100644 --- a/Documentation/devicetree/bindings/regulator/tps6586x.txt +++ b/Documentation/devicetree/bindings/regulator/tps6586x.txt @@ -6,12 +6,16 @@ Required properties: - interrupts: the interrupt outputs of the controller - #gpio-cells: number of cells to describe a GPIO - gpio-controller: mark the device as a GPIO controller -- regulators: list of regulators provided by this controller, must have - property "regulator-compatible" to match their hardware counterparts: - sm[0-2], ldo[0-9] and ldo_rtc -- sm0-supply: The input supply for the SM0. -- sm1-supply: The input supply for the SM1. -- sm2-supply: The input supply for the SM2. +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name (or the deprecated + regulator-compatible property if present), with valid values listed below. + The content of each sub-node is defined by the standard binding for + regulators; see regulator.txt. + sys, sm[0-2], ldo[0-9] and ldo_rtc +- sys-supply: The input supply for SYS. +- vin-sm0-supply: The input supply for the SM0. +- vin-sm1-supply: The input supply for the SM1. +- vin-sm2-supply: The input supply for the SM2. - vinldo01-supply: The input supply for the LDO1 and LDO2 - vinldo23-supply: The input supply for the LDO2 and LDO3 - vinldo4-supply: The input supply for the LDO4 @@ -20,6 +24,9 @@ Required properties: Each regulator is defined using the standard binding for regulators. +Note: LDO5 and LDO_RTC is supplied by SYS regulator internally and driver + take care of making proper parent child relationship. + Example: pmu: tps6586x@34 { @@ -30,9 +37,10 @@ Example: #gpio-cells = <2>; gpio-controller; - sm0-supply = <&some_reg>; - sm1-supply = <&some_reg>; - sm2-supply = <&some_reg>; + sys-supply = <&some_reg>; + vin-sm0-supply = <&some_reg>; + vin-sm1-supply = <&some_reg>; + vin-sm2-supply = <&some_reg>; vinldo01-supply = <...>; vinldo23-supply = <...>; vinldo4-supply = <...>; @@ -40,103 +48,80 @@ Example: vinldo9-supply = <...>; regulators { - #address-cells = <1>; - #size-cells = <0>; + sys_reg: sys { + regulator-name = "vdd_sys"; + regulator-boot-on; + regulator-always-on; + }; - sm0_reg: regulator@0 { - reg = <0>; - regulator-compatible = "sm0"; + sm0_reg: sm0 { regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm1_reg: regulator@1 { - reg = <1>; - regulator-compatible = "sm1"; + sm1_reg: sm1 { regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm2_reg: regulator@2 { - reg = <2>; - regulator-compatible = "sm2"; + sm2_reg: sm2 { regulator-min-microvolt = <3000000>; regulator-max-microvolt = <4550000>; regulator-boot-on; regulator-always-on; }; - ldo0_reg: regulator@3 { - reg = <3>; - regulator-compatible = "ldo0"; + ldo0_reg: ldo0 { regulator-name = "PCIE CLK"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; - ldo1_reg: regulator@4 { - reg = <4>; - regulator-compatible = "ldo1"; + ldo1_reg: ldo1 { regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo2_reg: regulator@5 { - reg = <5>; - regulator-compatible = "ldo2"; + ldo2_reg: ldo2 { regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo3_reg: regulator@6 { - reg = <6>; - regulator-compatible = "ldo3"; + ldo3_reg: ldo3 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo4_reg: regulator@7 { - reg = <7>; - regulator-compatible = "ldo4"; + ldo4_reg: ldo4 { regulator-min-microvolt = <1700000>; regulator-max-microvolt = <2475000>; }; - ldo5_reg: regulator@8 { - reg = <8>; - regulator-compatible = "ldo5"; + ldo5_reg: ldo5 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo6_reg: regulator@9 { - reg = <9>; - regulator-compatible = "ldo6"; + ldo6_reg: ldo6 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo7_reg: regulator@10 { - reg = <10>; - regulator-compatible = "ldo7"; + ldo7_reg: ldo7 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo8_reg: regulator@11 { - reg = <11>; - regulator-compatible = "ldo8"; + ldo8_reg: ldo8 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo9_reg: regulator@12 { - reg = <12>; - regulator-compatible = "ldo9"; + ldo9_reg: ldo9 { regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; diff --git a/Documentation/devicetree/bindings/rtc/pxa-rtc.txt b/Documentation/devicetree/bindings/rtc/pxa-rtc.txt new file mode 100644 index 00000000000..8c6672a1b7d --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/pxa-rtc.txt @@ -0,0 +1,14 @@ +* PXA RTC + +PXA specific RTC driver. + +Required properties: +- compatible : Should be "marvell,pxa-rtc" + +Examples: + +rtc@40900000 { + compatible = "marvell,pxa-rtc"; + reg = <0x40900000 0x3c>; + interrupts = <30 31>; +}; diff --git a/Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt b/Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt new file mode 100644 index 00000000000..3c0484c4958 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 Realtime Clock Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-rtc" +- reg : Should contain 1 register ranges(address and length) +- interrupts : alarm interrupt + +Example: + + rtc@d8100000 { + compatible = "via,vt8500-rtc"; + reg = <0xd8100000 0x10000>; + interrupts = <48>; + }; diff --git a/Documentation/devicetree/bindings/sound/ux500-mop500.txt b/Documentation/devicetree/bindings/sound/ux500-mop500.txt new file mode 100644 index 00000000000..48e071c96b4 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ux500-mop500.txt @@ -0,0 +1,39 @@ +* MOP500 Audio Machine Driver + +This node is responsible for linking together all ux500 Audio Driver components. + +Required properties: + - compatible : "stericsson,snd-soc-mop500" + +Non-standard properties: + - stericsson,cpu-dai : Phandle to the CPU-side DAI + - stericsson,audio-codec : Phandle to the Audio CODEC + - stericsson,card-name : Over-ride default card name + +Example: + + sound { + compatible = "stericsson,snd-soc-mop500"; + + stericsson,cpu-dai = <&msp1 &msp3>; + stericsson,audio-codec = <&codec>; + }; + + msp1: msp@80124000 { + compatible = "stericsson,ux500-msp-i2s"; + reg = <0x80124000 0x1000>; + interrupts = <0 62 0x4>; + v-ape-supply = <&db8500_vape_reg>; + }; + + msp3: msp@80125000 { + compatible = "stericsson,ux500-msp-i2s"; + reg = <0x80125000 0x1000>; + interrupts = <0 62 0x4>; + v-ape-supply = <&db8500_vape_reg>; + }; + + codec: ab8500-codec { + compatible = "stericsson,ab8500-codec"; + stericsson,earpeice-cmv = <950>; /* Units in mV. */ + }; diff --git a/Documentation/devicetree/bindings/sound/ux500-msp.txt b/Documentation/devicetree/bindings/sound/ux500-msp.txt new file mode 100644 index 00000000000..99acd9c774e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ux500-msp.txt @@ -0,0 +1,43 @@ +* ux500 MSP (CPU-side Digital Audio Interface) + +Required properties: + - compatible :"stericsson,ux500-msp-i2s" + - reg : Physical base address and length of the device's registers. + +Optional properties: + - interrupts : The interrupt output from the device. + - interrupt-parent : The parent interrupt controller. + - <name>-supply : Phandle to the regulator <name> supply + +Example: + + sound { + compatible = "stericsson,snd-soc-mop500"; + + stericsson,platform-pcm-dma = <&pcm>; + stericsson,cpu-dai = <&msp1 &msp3>; + stericsson,audio-codec = <&codec>; + }; + + pcm: ux500-pcm { + compatible = "stericsson,ux500-pcm"; + }; + + msp1: msp@80124000 { + compatible = "stericsson,ux500-msp-i2s"; + reg = <0x80124000 0x1000>; + interrupts = <0 62 0x4>; + v-ape-supply = <&db8500_vape_reg>; + }; + + msp3: msp@80125000 { + compatible = "stericsson,ux500-msp-i2s"; + reg = <0x80125000 0x1000>; + interrupts = <0 62 0x4>; + v-ape-supply = <&db8500_vape_reg>; + }; + + codec: ab8500-codec { + compatible = "stericsson,ab8500-codec"; + stericsson,earpeice-cmv = <950>; /* Units in mV. */ + }; diff --git a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt new file mode 100644 index 00000000000..801d58cb6d4 --- /dev/null +++ b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt @@ -0,0 +1,15 @@ +* Freescale i.MX28 LRADC device driver + +Required properties: +- compatible: Should be "fsl,imx28-lradc" +- reg: Address and length of the register set for the device +- interrupts: Should contain the LRADC interrupts + +Examples: + + lradc@80050000 { + compatible = "fsl,imx28-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <10 14 15 16 17 18 19 + 20 21 22 23 24 25>; + }; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt new file mode 100644 index 00000000000..07654f0338b --- /dev/null +++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt @@ -0,0 +1,41 @@ +Freescale i.MX IPUv3 +==================== + +Required properties: +- compatible: Should be "fsl,<chip>-ipu" +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain sync interrupt and error interrupt, + in this order. +- #crtc-cells: 1, See below + +example: + +ipu: ipu@18000000 { + #crtc-cells = <1>; + compatible = "fsl,imx53-ipu"; + reg = <0x18000000 0x080000000>; + interrupts = <11 10>; +}; + +Parallel display support +======================== + +Required properties: +- compatible: Should be "fsl,imx-parallel-display" +- crtc: the crtc this display is connected to, see below +Optional properties: +- interface_pix_fmt: How this display is connected to the + crtc. Currently supported types: "rgb24", "rgb565" +- edid: verbatim EDID data block describing attached display. +- ddc: phandle describing the i2c bus handling the display data + channel + +example: + +display@di0 { + compatible = "fsl,imx-parallel-display"; + edid = [edid-data]; + crtc = <&ipu 0>; + interface-pix-fmt = "rgb24"; +}; diff --git a/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt b/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt new file mode 100644 index 00000000000..2de21c2acf5 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt @@ -0,0 +1,22 @@ +BCM2835 System Timer + +The System Timer peripheral provides four 32-bit timer channels and a +single 64-bit free running counter. Each channel has an output compare +register, which is compared against the 32 least significant bits of the +free running counter values, and generates an interrupt. + +Required properties: + +- compatible : should be "brcm,bcm2835-system-timer.txt" +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 4 interrupt sinks; one per timer channel. +- clock-frequency : The frequency of the clock that drives the counter, in Hz. + +Example: + +timer { + compatible = "brcm,bcm2835-system-timer"; + reg = <0x7e003000 0x1000>; + interrupts = <1 0>, <1 1>, <1 2>, <1 3>; + clock-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt new file mode 100644 index 00000000000..0d439dfc1aa --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt @@ -0,0 +1,14 @@ +* NXP LPC32xx SoC High Speed UART + +Required properties: +- compatible: Should be "nxp,lpc3220-hsuart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt + +Example: + + uart1: serial@40014000 { + compatible = "nxp,lpc3220-hsuart"; + reg = <0x40014000 0x1000>; + interrupts = <26 0>; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt index 0847fdeee11..ba385f2e0dd 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -25,6 +25,8 @@ Optional properties: accesses to the UART (e.g. TI davinci). - used-by-rtas : set to indicate that the port is in use by the OpenFirmware RTAS and should not be registered. +- no-loopback-test: set to indicate that the port does not implements loopback + test mode Example: diff --git a/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt new file mode 100644 index 00000000000..5feef1ef167 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt @@ -0,0 +1,17 @@ +VIA/Wondermedia VT8500 UART Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-uart" +- reg : Should contain 1 register ranges(address and length) +- interrupts : UART interrupt +- clocks : phandle to the uart source clock (usually a 24Mhz fixed clock) + +Example: + + uart@d8210000 { + compatible = "via,vt8500-uart"; + reg = <0xd8210000 0x1040>; + interrupts = <47>; + clocks = <&ref24>; + }; diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt new file mode 100644 index 00000000000..ca8fa56e9f0 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -0,0 +1,14 @@ +AM33XX MUSB GLUE + - compatible : Should be "ti,musb-am33xx" + - ti,hwmods : must be "usb_otg_hs" + - multipoint : Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. + - num_eps : Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" + - ram_bits : Specifies the ram address size. Should be set to "12" + - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + represents PERIPHERAL. + - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2" + represents PERIPHERAL. + - power : Should be "250". This signifies the controller can supply upto + 500mA when operating in host mode. diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt index 2c290418bb2..5778b9c83bd 100644 --- a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt +++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt @@ -7,7 +7,10 @@ Required properties: Optional properties: - fsl,usbphy: phandler of usb phy that connects to the only one port +- fsl,usbmisc: phandler of non-core register device, with one argument + that indicate usb controller index - vbus-supply: regulator for vbus +- disable-over-current: disable over current detect Examples: usb@02184000 { /* USB OTG */ @@ -15,4 +18,6 @@ usb@02184000 { /* USB OTG */ reg = <0x02184000 0x200>; interrupts = <0 43 0x04>; fsl,usbphy = <&usbphy1>; + fsl,usbmisc = <&usbmisc 0>; + disable-over-current; }; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt new file mode 100644 index 00000000000..29a043ecda5 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -0,0 +1,33 @@ +OMAP GLUE + +OMAP MUSB GLUE + - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" + - ti,hwmods : must be "usb_otg_hs" + - multipoint : Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. + - num_eps : Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" + - ram_bits : Specifies the ram address size. Should be set to "12" + - interface_type : This is a board specific setting to describe the type of + interface between the controller and the phy. It should be "0" or "1" + specifying ULPI and UTMI respectively. + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + represents PERIPHERAL. + - power : Should be "50". This signifies the controller can supply upto + 100mA when operating in host mode. + +SOC specific device node entry +usb_otg_hs: usb_otg_hs@4a0ab000 { + compatible = "ti,omap4-musb"; + ti,hwmods = "usb_otg_hs"; + multipoint = <1>; + num_eps = <16>; + ram_bits = <12>; +}; + +Board specific device node entry +&usb_otg_hs { + interface_type = <1>; + mode = <3>; + power = <50>; +}; diff --git a/Documentation/devicetree/bindings/usb/platform-uhci.txt b/Documentation/devicetree/bindings/usb/platform-uhci.txt new file mode 100644 index 00000000000..a4fb0719d15 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/platform-uhci.txt @@ -0,0 +1,15 @@ +Generic Platform UHCI Controller +----------------------------------------------------- + +Required properties: +- compatible : "platform-uhci" +- reg : Should contain 1 register ranges(address and length) +- interrupts : UHCI controller interrupt + +Example: + + uhci@d8007b00 { + compatible = "platform-uhci"; + reg = <0xd8007b00 0x200>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/usb/pxa-usb.txt b/Documentation/devicetree/bindings/usb/pxa-usb.txt new file mode 100644 index 00000000000..79729a948d5 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/pxa-usb.txt @@ -0,0 +1,31 @@ +PXA USB controllers + +OHCI + +Required properties: + - compatible: Should be "marvell,pxa-ohci" for USB controllers + used in host mode. + +Optional properties: + - "marvell,enable-port1", "marvell,enable-port2", "marvell,enable-port3" + If present, enables the appropriate USB port of the controller. + - "marvell,port-mode" selects the mode of the ports: + 1 = PMM_NPS_MODE + 2 = PMM_GLOBAL_MODE + 3 = PMM_PERPORT_MODE + - "marvell,power-sense-low" - power sense pin is low-active. + - "marvell,power-control-low" - power control pin is low-active. + - "marvell,no-oc-protection" - disable over-current protection. + - "marvell,oc-mode-perport" - enable per-port over-current protection. + - "marvell,power_on_delay" Power On to Power Good time - in ms. + +Example: + + usb0: ohci@4c000000 { + compatible = "marvell,pxa-ohci", "usb-ohci"; + reg = <0x4c000000 0x100000>; + interrupts = <18>; + marvell,enable-port1; + marvell,port-mode = <2>; /* PMM_GLOBAL_MODE */ + }; + diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt new file mode 100644 index 00000000000..36b9aede3f4 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt @@ -0,0 +1,40 @@ +USB COMPARATOR OF TWL CHIPS + +TWL6030 USB COMPARATOR + - compatible : Should be "ti,twl6030-usb" + - interrupts : Two interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts when + the controller has to act as host and the second interrupt number is the + usb interrupt number that raises VBUS interrupts when the controller has to + act as device + - usb-supply : phandle to the regulator device tree node. It should be vusb + if it is twl6030 or ldousb if it is twl6025 subclass. + +twl6030-usb { + compatible = "ti,twl6030-usb"; + interrupts = < 4 10 >; +}; + +Board specific device node entry +&twl6030-usb { + usb-supply = <&vusb>; +}; + +TWL4030 USB PHY AND COMPARATOR + - compatible : Should be "ti,twl4030-usb" + - interrupts : The interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts + and VBUS interrupts. The second interrupt number is optional. + - <supply-name>-supply : phandle to the regulator device tree node. + <supply-name> should be vusb1v5, vusb1v8 and vusb3v1 + - usb_mode : The mode used by the phy to connect to the controller. "1" + specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode. + +twl4030-usb { + compatible = "ti,twl4030-usb"; + interrupts = < 10 4 >; + usb1v5-supply = <&vusb1v5>; + usb1v8-supply = <&vusb1v8>; + usb3v1-supply = <&vusb3v1>; + usb_mode = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt new file mode 100644 index 00000000000..80d4148cb66 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt @@ -0,0 +1,17 @@ +USB PHY + +OMAP USB2 PHY + +Required properties: + - compatible: Should be "ti,omap-usb2" + - reg : Address and length of the register set for the device. Also +add the address of control module dev conf register until a driver for +control module is added + +This is usually a subnode of ocp2scp to which it is connected. + +usb2phy@4a0ad080 { + compatible = "ti,omap-usb2"; + reg = <0x4a0ad080 0x58>, + <0x4a002300 0x4>; +}; diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt new file mode 100644 index 00000000000..97ce94e1a6c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt @@ -0,0 +1,14 @@ +* Freescale i.MX non-core registers + +Required properties: +- #index-cells: Cells used to descibe usb controller index. Should be <1> +- compatible: Should be one of below: + "fsl,imx6q-usbmisc" for imx6q +- reg: Should contain registers location and length + +Examples: +usbmisc@02184800 { + #index-cells = <1>; + compatible = "fsl,imx6q-usbmisc"; + reg = <0x02184800 0x200>; +}; diff --git a/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt b/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt new file mode 100644 index 00000000000..17b3ad1d97e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 EHCI Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-ehci" +- reg : Should contain 1 register ranges(address and length) +- interrupts : ehci controller interrupt + +Example: + + ehci@d8007900 { + compatible = "via,vt8500-ehci"; + reg = <0xd8007900 0x200>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/usb/vt8500-ehci.txt b/Documentation/devicetree/bindings/usb/vt8500-ehci.txt new file mode 100644 index 00000000000..5fb8fd6e250 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/vt8500-ehci.txt @@ -0,0 +1,12 @@ +VIA VT8500 and Wondermedia WM8xxx SoC USB controllers. + +Required properties: + - compatible: Should be "via,vt8500-ehci" or "wm,prizm-ehci". + - reg: Address range of the ehci registers. size should be 0x200 + - interrupts: Should contain the ehci interrupt. + +usb: ehci@D8007100 { + compatible = "wm,prizm-ehci", "usb-ehci"; + reg = <0xD8007100 0x200>; + interrupts = <1>; +}; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index db4d3af3643..9de2b9ff9d6 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -10,6 +10,7 @@ apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. atmel Atmel Corporation bosch Bosch Sensortec GmbH +brcm Broadcom Corporation cavium Cavium, Inc. chrp Common Hardware Reference Platform cortina Cortina Systems, Inc. @@ -47,5 +48,7 @@ sirf SiRF Technology, Inc. st STMicroelectronics stericsson ST-Ericsson ti Texas Instruments +via VIA Technologies, Inc. wlf Wolfson Microelectronics +wm Wondermedia Technologies, Inc. xlnx Xilinx diff --git a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt new file mode 100644 index 00000000000..c870b6478ec --- /dev/null +++ b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt @@ -0,0 +1,62 @@ +VIA VT8500 Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-fb" +- reg : Should contain 1 register ranges(address and length) +- interrupts : framebuffer controller interrupt +- display: a phandle pointing to the display node + +Required nodes: +- display: a display node is required to initialize the lcd panel + This should be in the board dts. +- default-mode: a videomode within the display with timing parameters + as specified below. + +Example: + + fb@d800e400 { + compatible = "via,vt8500-fb"; + reg = <0xd800e400 0x400>; + interrupts = <12>; + display = <&display>; + default-mode = <&mode0>; + }; + +VIA VT8500 Display +----------------------------------------------------- +Required properties (as per of_videomode_helper): + + - hactive, vactive: Display resolution + - hfront-porch, hback-porch, hsync-len: Horizontal Display timing parameters + in pixels + vfront-porch, vback-porch, vsync-len: Vertical display timing parameters in + lines + - clock: displayclock in Hz + - bpp: lcd panel bit-depth. + <16> for RGB565, <32> for RGB888 + +Optional properties (as per of_videomode_helper): + - width-mm, height-mm: Display dimensions in mm + - hsync-active-high (bool): Hsync pulse is active high + - vsync-active-high (bool): Vsync pulse is active high + - interlaced (bool): This is an interlaced mode + - doublescan (bool): This is a doublescan mode + +Example: + display: display@0 { + modes { + mode0: mode@0 { + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hfront-porch = <40>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; + clock = <0>; /* unused but required */ + bpp = <16>; /* non-standard but required */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt b/Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt new file mode 100644 index 00000000000..a850fa011f0 --- /dev/null +++ b/Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt @@ -0,0 +1,13 @@ +VIA/Wondermedia Graphics Engine Controller +----------------------------------------------------- + +Required properties: +- compatible : "wm,prizm-ge-rops" +- reg : Should contain 1 register ranges(address and length) + +Example: + + ge_rops@d8050400 { + compatible = "wm,prizm-ge-rops"; + reg = <0xd8050400 0x100>; + }; diff --git a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt new file mode 100644 index 00000000000..3d325e1d11e --- /dev/null +++ b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt @@ -0,0 +1,23 @@ +Wondermedia WM8505 Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : "wm,wm8505-fb" +- reg : Should contain 1 register ranges(address and length) +- via,display: a phandle pointing to the display node + +Required nodes: +- display: a display node is required to initialize the lcd panel + This should be in the board dts. See definition in + Documentation/devicetree/bindings/video/via,vt8500-fb.txt +- default-mode: a videomode node as specified in + Documentation/devicetree/bindings/video/via,vt8500-fb.txt + +Example: + + fb@d8050800 { + compatible = "wm,wm8505-fb"; + reg = <0xd8050800 0x200>; + display = <&display>; + default-mode = <&mode0>; + }; diff --git a/Documentation/devicetree/bindings/w1/w1-gpio.txt b/Documentation/devicetree/bindings/w1/w1-gpio.txt new file mode 100644 index 00000000000..6e09c35d9f1 --- /dev/null +++ b/Documentation/devicetree/bindings/w1/w1-gpio.txt @@ -0,0 +1,22 @@ +w1-gpio devicetree bindings + +Required properties: + + - compatible: "w1-gpio" + - gpios: one or two GPIO specs: + - the first one is used as data I/O pin + - the second one is optional. If specified, it is used as + enable pin for an external pin pullup. + +Optional properties: + + - linux,open-drain: if specified, the data pin is considered in + open-drain mode. + +Examples: + + onewire@0 { + compatible = "w1-gpio"; + gpios = <&gpio 126 0>, <&gpio 105 0>; + }; + |