diff options
Diffstat (limited to 'Documentation/devicetree')
73 files changed, 2449 insertions, 50 deletions
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt index 07c65e3cdcb..f4d04a06728 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt @@ -3,9 +3,11 @@ Altera SOCFPGA System Manager Required properties: - compatible : "altr,sys-mgr" - reg : Should contain 1 register ranges(address and length) +- cpu1-start-addr : CPU1 start address in hex. Example: sysmgr@ffd08000 { compatible = "altr,sys-mgr"; reg = <0xffd08000 0x1000>; + cpu1-start-addr = <0xffd080c4>; }; diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index 52478c83d0c..20746e5abe6 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -1,13 +1,14 @@ * ARM architected timer -ARM Cortex-A7 and Cortex-A15 have a per-core architected timer, which -provides per-cpu timers. +ARM cores may have a per-core architected timer, which provides per-cpu timers. The timer is attached to a GIC to deliver its per-processor interrupts. ** Timer node properties: -- compatible : Should at least contain "arm,armv7-timer". +- compatible : Should at least contain one of + "arm,armv7-timer" + "arm,armv8-timer" - interrupts : Interrupt list for secure, non-secure, virtual and hypervisor timers, in that order. diff --git a/Documentation/devicetree/bindings/arm/armadeus.txt b/Documentation/devicetree/bindings/arm/armadeus.txt new file mode 100644 index 00000000000..9821283ff51 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armadeus.txt @@ -0,0 +1,6 @@ +Armadeus i.MX Platforms Device Tree Bindings +----------------------------------------------- + +APF51: i.MX51 based module. +Required root node properties: + - compatible = "armadeus,imx51-apf51", "fsl,imx51"; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index f79818711e8..e935d7d4ac4 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -5,6 +5,14 @@ i.MX23 Evaluation Kit Required root node properties: - compatible = "fsl,imx23-evk", "fsl,imx23"; +i.MX25 Product Development Kit +Required root node properties: + - compatible = "fsl,imx25-pdk", "fsl,imx25"; + +i.MX27 Product Development Kit +Required root node properties: + - compatible = "fsl,imx27-pdk", "fsl,imx27"; + i.MX28 Evaluation Kit Required root node properties: - compatible = "fsl,imx28-evk", "fsl,imx28"; diff --git a/Documentation/devicetree/bindings/arm/sirf.txt b/Documentation/devicetree/bindings/arm/sirf.txt index 1881e1c6dda..c6ba6d3c747 100644 --- a/Documentation/devicetree/bindings/arm/sirf.txt +++ b/Documentation/devicetree/bindings/arm/sirf.txt @@ -1,3 +1,9 @@ -prima2 "cb" evaluation board +CSR SiRFprimaII and SiRFmarco device tree bindings. +======================================== + Required root node properties: - - compatible = "sirf,prima2-cb", "sirf,prima2"; + - compatible: + - "sirf,prima2-cb" : prima2 "cb" evaluation board + - "sirf,marco-cb" : marco "cb" evaluation board + - "sirf,prima2" : prima2 device based board + - "sirf,marco" : marco device based board diff --git a/Documentation/devicetree/bindings/arm/ste-nomadik.txt b/Documentation/devicetree/bindings/arm/ste-nomadik.txt new file mode 100644 index 00000000000..19bca04b81c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/ste-nomadik.txt @@ -0,0 +1,27 @@ +ST-Ericsson Nomadik Device Tree Bindings + +For various board the "board" node may contain specific properties +that pertain to this particular board, such as board-specific GPIOs. + +Boards with the Nomadik SoC include: + +S8815 "MiniKit" manufactured by Calao Systems: + +Required root node property: + +compatible="calaosystems,usb-s8815"; + +Required node: usb-s8815 + +Example: + +usb-s8815 { + ethernet-gpio { + gpios = <&gpio3 19 0x1>; + interrupts = <19 0x1>; + interrupt-parent = <&gpio3>; + }; + mmcsd-gpio { + gpios = <&gpio3 16 0x1>; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt index 6e69d2e5e76..ed9c8533443 100644 --- a/Documentation/devicetree/bindings/arm/tegra.txt +++ b/Documentation/devicetree/bindings/arm/tegra.txt @@ -1,14 +1,34 @@ NVIDIA Tegra device tree bindings ------------------------------------------- -Boards with the tegra20 SoC shall have the following properties: +SoCs +------------------------------------------- -Required root node property: +Each device tree must specify which Tegra SoC it uses, using one of the +following compatible values: -compatible = "nvidia,tegra20"; + nvidia,tegra20 + nvidia,tegra30 -Boards with the tegra30 SoC shall have the following properties: +Boards +------------------------------------------- -Required root node property: +Each device tree must specify which one or more of the following +board-specific compatible values: -compatible = "nvidia,tegra30"; + ad,medcom-wide + ad,plutux + ad,tamonten + ad,tec + compal,paz00 + compulab,trimslice + nvidia,beaver + nvidia,cardhu + nvidia,cardhu-a02 + nvidia,cardhu-a04 + nvidia,harmony + nvidia,seaboard + nvidia,ventana + nvidia,whistler + toradex,colibri_t20-512 + toradex,iris diff --git a/Documentation/devicetree/bindings/arm/vt8500.txt b/Documentation/devicetree/bindings/arm/vt8500.txt index d657832c681..87dc1ddf477 100644 --- a/Documentation/devicetree/bindings/arm/vt8500.txt +++ b/Documentation/devicetree/bindings/arm/vt8500.txt @@ -12,3 +12,11 @@ compatible = "wm,wm8505"; Boards with the Wondermedia WM8650 SoC shall have the following properties: Required root node property: compatible = "wm,wm8650"; + +Boards with the Wondermedia WM8750 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8750"; + +Boards with the Wondermedia WM8850 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8850"; diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt new file mode 100644 index 00000000000..5ddb2e9efaa --- /dev/null +++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt @@ -0,0 +1,84 @@ +Device tree bindings for OMAP general purpose memory controllers (GPMC) + +The actual devices are instantiated from the child nodes of a GPMC node. + +Required properties: + + - compatible: Should be set to one of the following: + + ti,omap2420-gpmc (omap2420) + ti,omap2430-gpmc (omap2430) + ti,omap3430-gpmc (omap3430 & omap3630) + ti,omap4430-gpmc (omap4430 & omap4460 & omap543x) + ti,am3352-gpmc (am335x devices) + + - reg: A resource specifier for the register space + (see the example below) + - ti,hwmods: Should be set to "ti,gpmc" until the DT transition is + completed. + - #address-cells: Must be set to 2 to allow memory address translation + - #size-cells: Must be set to 1 to allow CS address passing + - gpmc,num-cs: The maximum number of chip-select lines that controller + can support. + - gpmc,num-waitpins: The maximum number of wait pins that controller can + support. + - ranges: Must be set up to reflect the memory layout with four + integer values for each chip-select line in use: + + <cs-number> 0 <physical address of mapping> <size> + + Currently, calculated values derived from the contents + of the per-CS register GPMC_CONFIG7 (as set up by the + bootloader) are used for the physical address decoding. + As this will change in the future, filling correct + values here is a requirement. + +Timing properties for child nodes. All are optional and default to 0. + + - gpmc,sync-clk: Minimum clock period for synchronous mode, in picoseconds + + Chip-select signal timings corresponding to GPMC_CONFIG2: + - gpmc,cs-on: Assertion time + - gpmc,cs-rd-off: Read deassertion time + - gpmc,cs-wr-off: Write deassertion time + + ADV signal timings corresponding to GPMC_CONFIG3: + - gpmc,adv-on: Assertion time + - gpmc,adv-rd-off: Read deassertion time + - gpmc,adv-wr-off: Write deassertion time + + WE signals timings corresponding to GPMC_CONFIG4: + - gpmc,we-on: Assertion time + - gpmc,we-off: Deassertion time + + OE signals timings corresponding to GPMC_CONFIG4: + - gpmc,oe-on: Assertion time + - gpmc,oe-off: Deassertion time + + Access time and cycle time timings corresponding to GPMC_CONFIG5: + - gpmc,page-burst-access: Multiple access word delay + - gpmc,access: Start-cycle to first data valid delay + - gpmc,rd-cycle: Total read cycle time + - gpmc,wr-cycle: Total write cycle time + +The following are only applicable to OMAP3+ and AM335x: + - gpmc,wr-access + - gpmc,wr-data-mux-bus + + +Example for an AM33xx board: + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x50000000 0x2000>; + interrupts = <100>; + + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ + + /* child nodes go here */ + }; diff --git a/Documentation/devicetree/bindings/clock/imx31-clock.txt b/Documentation/devicetree/bindings/clock/imx31-clock.txt new file mode 100644 index 00000000000..19df842c694 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx31-clock.txt @@ -0,0 +1,91 @@ +* Clock bindings for Freescale i.MX31 + +Required properties: +- compatible: Should be "fsl,imx31-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX31 +clocks and IDs. + + Clock ID + ----------------------- + dummy 0 + ckih 1 + ckil 2 + mpll 3 + spll 4 + upll 5 + mcu_main 6 + hsp 7 + ahb 8 + nfc 9 + ipg 10 + per_div 11 + per 12 + csi_sel 13 + fir_sel 14 + csi_div 15 + usb_div_pre 16 + usb_div_post 17 + fir_div_pre 18 + fir_div_post 19 + sdhc1_gate 20 + sdhc2_gate 21 + gpt_gate 22 + epit1_gate 23 + epit2_gate 24 + iim_gate 25 + ata_gate 26 + sdma_gate 27 + cspi3_gate 28 + rng_gate 29 + uart1_gate 30 + uart2_gate 31 + ssi1_gate 32 + i2c1_gate 33 + i2c2_gate 34 + i2c3_gate 35 + hantro_gate 36 + mstick1_gate 37 + mstick2_gate 38 + csi_gate 39 + rtc_gate 40 + wdog_gate 41 + pwm_gate 42 + sim_gate 43 + ect_gate 44 + usb_gate 45 + kpp_gate 46 + ipu_gate 47 + uart3_gate 48 + uart4_gate 49 + uart5_gate 50 + owire_gate 51 + ssi2_gate 52 + cspi1_gate 53 + cspi2_gate 54 + gacc_gate 55 + emi_gate 56 + rtic_gate 57 + firi_gate 58 + +Examples: + +clks: ccm@53f80000{ + compatible = "fsl,imx31-ccm"; + reg = <0x53f80000 0x4000>; + interrupts = <0 31 0x04 0 53 0x04>; + #clock-cells = <1>; +}; + +uart1: serial@43f90000 { + compatible = "fsl,imx31-uart", "fsl,imx21-uart"; + reg = <0x43f90000 0x4000>; + interrupts = <45>; + clocks = <&clks 10>, <&clks 30>; + clock-names = "ipg", "per"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt index 04ad47876be..2a0c904c46a 100644 --- a/Documentation/devicetree/bindings/clock/imx5-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx5-clock.txt @@ -171,6 +171,7 @@ clocks and IDs. can_sel 156 can1_serial_gate 157 can1_ipg_gate 158 + owire_gate 159 Examples (for mx53): diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index f73fdf59556..969b38e06ad 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -203,6 +203,8 @@ clocks and IDs. pcie_ref 188 pcie_ref_125m 189 enet_ref 190 + usbphy1_gate 191 + usbphy2_gate 192 Examples: diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt index 7337005ef5e..cffc93d97f5 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -89,7 +89,7 @@ ID Clock Peripheral 16 xor1 XOR DMA 1 17 crypto CESA engine 18 pex1 PCIe Cntrl 1 -19 ge1 Gigabit Ethernet 0 +19 ge1 Gigabit Ethernet 1 20 tdm Time Division Mplx Required properties: diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt new file mode 100644 index 00000000000..0921fac7352 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt @@ -0,0 +1,205 @@ +NVIDIA Tegra20 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra20-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the CAR. + + The first 96 clocks are numbered to match the bits in the CAR's CLK_OUT_ENB + registers. These IDs often match those in the CAR's RST_DEVICES registers, + but not in all cases. Some bits in CLK_OUT_ENB affect multiple clocks. In + this case, those clocks are assigned IDs above 95 in order to highlight + this issue. Implementations that interpret these clock IDs as bit values + within the CLK_OUT_ENB or RST_DEVICES registers should be careful to + explicitly handle these special cases. + + The balance of the clocks controlled by the CAR are assigned IDs of 96 and + above. + + 0 cpu + 1 unassigned + 2 unassigned + 3 ac97 + 4 rtc + 5 tmr + 6 uart1 + 7 unassigned (register bit affects uart2 and vfir) + 8 gpio + 9 sdmmc2 + 10 unassigned (register bit affects spdif_in and spdif_out) + 11 i2s1 + 12 i2c1 + 13 ndflash + 14 sdmmc1 + 15 sdmmc4 + 16 twc + 17 pwm + 18 i2s2 + 19 epp + 20 unassigned (register bit affects vi and vi_sensor) + 21 2d + 22 usbd + 23 isp + 24 3d + 25 ide + 26 disp2 + 27 disp1 + 28 host1x + 29 vcp + 30 unassigned + 31 cache2 + + 32 mem + 33 ahbdma + 34 apbdma + 35 unassigned + 36 kbc + 37 stat_mon + 38 pmc + 39 fuse + 40 kfuse + 41 sbc1 + 42 snor + 43 spi1 + 44 sbc2 + 45 xio + 46 sbc3 + 47 dvc + 48 dsi + 49 unassigned (register bit affects tvo and cve) + 50 mipi + 51 hdmi + 52 csi + 53 tvdac + 54 i2c2 + 55 uart3 + 56 unassigned + 57 emc + 58 usb2 + 59 usb3 + 60 mpe + 61 vde + 62 bsea + 63 bsev + + 64 speedo + 65 uart4 + 66 uart5 + 67 i2c3 + 68 sbc4 + 69 sdmmc3 + 70 pcie + 71 owr + 72 afi + 73 csite + 74 unassigned + 75 avpucq + 76 la + 77 unassigned + 78 unassigned + 79 unassigned + 80 unassigned + 81 unassigned + 82 unassigned + 83 unassigned + 84 irama + 85 iramb + 86 iramc + 87 iramd + 88 cram2 + 89 audio_2x a/k/a audio_2x_sync_clk + 90 clk_d + 91 unassigned + 92 sus + 93 cdev1 + 94 cdev2 + 95 unassigned + + 96 uart2 + 97 vfir + 98 spdif_in + 99 spdif_out + 100 vi + 101 vi_sensor + 102 tvo + 103 cve + 104 osc + 105 clk_32k a/k/a clk_s + 106 clk_m + 107 sclk + 108 cclk + 109 hclk + 110 pclk + 111 blink + 112 pll_a + 113 pll_a_out0 + 114 pll_c + 115 pll_c_out1 + 116 pll_d + 117 pll_d_out0 + 118 pll_e + 119 pll_m + 120 pll_m_out1 + 121 pll_p + 122 pll_p_out1 + 123 pll_p_out2 + 124 pll_p_out3 + 125 pll_p_out4 + 126 pll_s + 127 pll_u + 128 pll_x + 129 cop a/k/a avp + 130 audio a/k/a audio_sync_clk + 131 pll_ref + 132 twd + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra20-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car 58>; /* usb2 */ + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + osc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt new file mode 100644 index 00000000000..f3da3be5fca --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt @@ -0,0 +1,262 @@ +NVIDIA Tegra30 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra30-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the CAR. + + The first 130 clocks are numbered to match the bits in the CAR's CLK_OUT_ENB + registers. These IDs often match those in the CAR's RST_DEVICES registers, + but not in all cases. Some bits in CLK_OUT_ENB affect multiple clocks. In + this case, those clocks are assigned IDs above 160 in order to highlight + this issue. Implementations that interpret these clock IDs as bit values + within the CLK_OUT_ENB or RST_DEVICES registers should be careful to + explicitly handle these special cases. + + The balance of the clocks controlled by the CAR are assigned IDs of 160 and + above. + + 0 cpu + 1 unassigned + 2 unassigned + 3 unassigned + 4 rtc + 5 timer + 6 uarta + 7 unassigned (register bit affects uartb and vfir) + 8 gpio + 9 sdmmc2 + 10 unassigned (register bit affects spdif_in and spdif_out) + 11 i2s1 + 12 i2c1 + 13 ndflash + 14 sdmmc1 + 15 sdmmc4 + 16 unassigned + 17 pwm + 18 i2s2 + 19 epp + 20 unassigned (register bit affects vi and vi_sensor) + 21 2d + 22 usbd + 23 isp + 24 3d + 25 unassigned + 26 disp2 + 27 disp1 + 28 host1x + 29 vcp + 30 i2s0 + 31 cop_cache + + 32 mc + 33 ahbdma + 34 apbdma + 35 unassigned + 36 kbc + 37 statmon + 38 pmc + 39 unassigned (register bit affects fuse and fuse_burn) + 40 kfuse + 41 sbc1 + 42 nor + 43 unassigned + 44 sbc2 + 45 unassigned + 46 sbc3 + 47 i2c5 + 48 dsia + 49 unassigned (register bit affects cve and tvo) + 50 mipi + 51 hdmi + 52 csi + 53 tvdac + 54 i2c2 + 55 uartc + 56 unassigned + 57 emc + 58 usb2 + 59 usb3 + 60 mpe + 61 vde + 62 bsea + 63 bsev + + 64 speedo + 65 uartd + 66 uarte + 67 i2c3 + 68 sbc4 + 69 sdmmc3 + 70 pcie + 71 owr + 72 afi + 73 csite + 74 pciex + 75 avpucq + 76 la + 77 unassigned + 78 unassigned + 79 dtv + 80 ndspeed + 81 i2cslow + 82 dsib + 83 unassigned + 84 irama + 85 iramb + 86 iramc + 87 iramd + 88 cram2 + 89 unassigned + 90 audio_2x a/k/a audio_2x_sync_clk + 91 unassigned + 92 csus + 93 cdev2 + 94 cdev1 + 95 unassigned + + 96 cpu_g + 97 cpu_lp + 98 3d2 + 99 mselect + 100 tsensor + 101 i2s3 + 102 i2s4 + 103 i2c4 + 104 sbc5 + 105 sbc6 + 106 d_audio + 107 apbif + 108 dam0 + 109 dam1 + 110 dam2 + 111 hda2codec_2x + 112 atomics + 113 audio0_2x + 114 audio1_2x + 115 audio2_2x + 116 audio3_2x + 117 audio4_2x + 118 audio5_2x + 119 actmon + 120 extern1 + 121 extern2 + 122 extern3 + 123 sata_oob + 124 sata + 125 hda + 127 se + 128 hda2hdmi + 129 sata_cold + + 160 uartb + 161 vfir + 162 spdif_in + 163 spdif_out + 164 vi + 165 vi_sensor + 166 fuse + 167 fuse_burn + 168 cve + 169 tvo + + 170 clk_32k + 171 clk_m + 172 clk_m_div2 + 173 clk_m_div4 + 174 pll_ref + 175 pll_c + 176 pll_c_out1 + 177 pll_m + 178 pll_m_out1 + 179 pll_p + 180 pll_p_out1 + 181 pll_p_out2 + 182 pll_p_out3 + 183 pll_p_out4 + 184 pll_a + 185 pll_a_out0 + 186 pll_d + 187 pll_d_out0 + 188 pll_d2 + 189 pll_d2_out0 + 190 pll_u + 191 pll_x + 192 pll_x_out0 + 193 pll_e + 194 spdif_in_sync + 195 i2s0_sync + 196 i2s1_sync + 197 i2s2_sync + 198 i2s3_sync + 199 i2s4_sync + 200 vimclk + 201 audio0 + 202 audio1 + 203 audio2 + 204 audio3 + 205 audio4 + 206 audio5 + 207 clk_out_1 (extern1) + 208 clk_out_2 (extern2) + 209 clk_out_3 (extern3) + 210 sclk + 211 blink + 212 cclk_g + 213 cclk_lp + 214 twd + 215 cml0 + 216 cml1 + 217 hclk + 218 pclk + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra30-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car 58>; /* usb2 */ + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + osc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; +}; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index fc9ce6f1688..e4022776ac6 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -54,8 +54,13 @@ PROPERTIES - compatible Usage: required Value type: <string> - Definition: Must include "fsl,sec-v4.0". Also includes SEC - ERA versions (optional) with which the device is compatible. + Definition: Must include "fsl,sec-v4.0" + + - fsl,sec-era + Usage: optional + Value type: <u32> + Definition: A standard property. Define the 'ERA' of the SEC + device. - #address-cells Usage: required @@ -107,7 +112,8 @@ PROPERTIES EXAMPLE crypto@300000 { - compatible = "fsl,sec-v4.0", "fsl,sec-era-v2.0"; + compatible = "fsl,sec-v4.0"; + fsl,sec-era = <2>; #address-cells = <1>; #size-cells = <1>; reg = <0x300000 0x10000>; diff --git a/Documentation/devicetree/bindings/dma/arm-pl330.txt b/Documentation/devicetree/bindings/dma/arm-pl330.txt index 36e27d54260..267565894db 100644 --- a/Documentation/devicetree/bindings/dma/arm-pl330.txt +++ b/Documentation/devicetree/bindings/dma/arm-pl330.txt @@ -10,7 +10,11 @@ Required properties: - interrupts: interrupt number to the cpu. Optional properties: -- dma-coherent : Present if dma operations are coherent + - dma-coherent : Present if dma operations are coherent + - #dma-cells: must be <1>. used to represent the number of integer + cells in the dmas property of client device. + - dma-channels: contains the total number of DMA channels supported by the DMAC + - dma-requests: contains the total number of DMA requests supported by the DMAC Example: @@ -18,16 +22,23 @@ Example: compatible = "arm,pl330", "arm,primecell"; reg = <0x12680000 0x1000>; interrupts = <99>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; Client drivers (device nodes requiring dma transfers from dev-to-mem or -mem-to-dev) should specify the DMA channel numbers using a two-value pair +mem-to-dev) should specify the DMA channel numbers and dma channel names as shown below. [property name] = <[phandle of the dma controller] [dma request id]>; + [property name] = <[dma channel name]> where 'dma request id' is the dma request number which is connected - to the client controller. The 'property name' is recommended to be - of the form <name>-dma-channel. + to the client controller. The 'property name' 'dmas' and 'dma-names' + as required by the generic dma device tree binding helpers. The dma + names correspond 1:1 with the dma request ids in the dmas property. - Example: tx-dma-channel = <&pdma0 12>; + Example: dmas = <&pdma0 12 + &pdma1 11>; + dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/dma/dma.txt b/Documentation/devicetree/bindings/dma/dma.txt new file mode 100644 index 00000000000..8f504e6bae1 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/dma.txt @@ -0,0 +1,81 @@ +* Generic DMA Controller and DMA request bindings + +Generic binding to provide a way for a driver using DMA Engine to retrieve the +DMA request or channel information that goes from a hardware device to a DMA +controller. + + +* DMA controller + +Required property: +- #dma-cells: Must be at least 1. Used to provide DMA controller + specific information. See DMA client binding below for + more details. + +Optional properties: +- dma-channels: Number of DMA channels supported by the controller. +- dma-requests: Number of DMA requests signals supported by the + controller. + +Example: + + dma: dma@48000000 { + compatible = "ti,omap-sdma"; + reg = <0x48000000 0x1000>; + interrupts = <0 12 0x4 + 0 13 0x4 + 0 14 0x4 + 0 15 0x4>; + #dma-cells = <1>; + dma-channels = <32>; + dma-requests = <127>; + }; + + +* DMA client + +Client drivers should specify the DMA property using a phandle to the controller +followed by DMA controller specific data. + +Required property: +- dmas: List of one or more DMA specifiers, each consisting of + - A phandle pointing to DMA controller node + - A number of integer cells, as determined by the + #dma-cells property in the node referenced by phandle + containing DMA controller specific information. This + typically contains a DMA request line number or a + channel number, but can contain any data that is used + required for configuring a channel. +- dma-names: Contains one identifier string for each DMA specifier in + the dmas property. The specific strings that can be used + are defined in the binding of the DMA client device. + Multiple DMA specifiers can be used to represent + alternatives and in this case the dma-names for those + DMA specifiers must be identical (see examples). + +Examples: + +1. A device with one DMA read channel, one DMA write channel: + + i2c1: i2c@1 { + ... + dmas = <&dma 2 /* read channel */ + &dma 3>; /* write channel */ + dma-names = "rx", "tx"; + ... + }; + +2. A single read-write channel with three alternative DMA controllers: + + dmas = <&dma1 5 + &dma2 7 + &dma3 2>; + dma-names = "rx-tx", "rx-tx", "rx-tx"; + +3. A device with three channels, one of which has two alternatives: + + dmas = <&dma1 2 /* read channel */ + &dma1 3 /* write channel */ + &dma2 0 /* error read */ + &dma3 0>; /* alternative error read */ + dma-names = "rx", "tx", "error", "error"; diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index c0d85dbcada..5bb3dfb6f1d 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -6,6 +6,26 @@ Required properties: - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - interrupt: Should contain the DMAC interrupt number +- nr_channels: Number of channels supported by hardware +- is_private: The device channels should be marked as private and not for by the + general purpose DMA channel allocator. False if not passed. +- chan_allocation_order: order of allocation of channel, 0 (default): ascending, + 1: descending +- chan_priority: priority of channels. 0 (default): increase from chan 0->n, 1: + increase from chan n->0 +- block_size: Maximum block size supported by the controller +- nr_masters: Number of AHB masters supported by the controller +- data_width: Maximum data width supported by hardware per AHB master + (0 - 8bits, 1 - 16bits, ..., 5 - 256bits) +- slave_info: + - bus_id: name of this device channel, not just a device name since + devices may have more than one channel e.g. "foo_tx". For using the + dw_generic_filter(), slave drivers must pass exactly this string as + param to filter function. + - cfg_hi: Platform-specific initializer for the CFG_HI register + - cfg_lo: Platform-specific initializer for the CFG_LO register + - src_master: src master for transfers on allocated channel. + - dst_master: dest master for transfers on allocated channel. Example: @@ -14,4 +34,28 @@ Example: reg = <0xfc000000 0x1000>; interrupt-parent = <&vic1>; interrupts = <12>; + + nr_channels = <8>; + chan_allocation_order = <1>; + chan_priority = <1>; + block_size = <0xfff>; + nr_masters = <2>; + data_width = <3 3 0 0>; + + slave_info { + uart0-tx { + bus_id = "uart0-tx"; + cfg_hi = <0x4000>; /* 0x8 << 11 */ + cfg_lo = <0>; + src_master = <0>; + dst_master = <1>; + }; + spi0-tx { + bus_id = "spi0-tx"; + cfg_hi = <0x2000>; /* 0x4 << 11 */ + cfg_lo = <0>; + src_master = <0>; + dst_master = <0>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt new file mode 100644 index 00000000000..9301c330d1a --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt @@ -0,0 +1,59 @@ +Device-Tree bindings for tilcdc DRM generic panel output driver + +Required properties: + - compatible: value should be "ti,tilcdc,panel". + - panel-info: configuration info to configure LCDC correctly for the panel + - ac-bias: AC Bias Pin Frequency + - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt + - dma-burst-sz: DMA burst size + - bpp: Bits per pixel + - fdd: FIFO DMA Request Delay + - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling + - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore + - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most + - fifo-th: DMA FIFO threshold + - display-timings: typical videomode of lcd panel. Multiple video modes + can be listed if the panel supports multiple timings, but the 'native-mode' + should be the preferred/default resolution. Refer to + Documentation/devicetree/bindings/video/display-timing.txt for display + timing binding details. + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + /* Settings for CDTech_S035Q01 / LCD3 cape: */ + lcd3 { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <16>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + display-timings { + native-mode = <&timing0>; + timing0: 320x240 { + hactive = <320>; + vactive = <240>; + hback-porch = <21>; + hfront-porch = <58>; + hsync-len = <47>; + vback-porch = <11>; + vfront-porch = <23>; + vsync-len = <2>; + clock-frequency = <8000000>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/slave.txt b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt new file mode 100644 index 00000000000..3d2c52460dc --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt @@ -0,0 +1,18 @@ +Device-Tree bindings for tilcdc DRM encoder slave output driver + +Required properties: + - compatible: value should be "ti,tilcdc,slave". + - i2c: the phandle for the i2c device the encoder slave is connected to + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + hdmi { + compatible = "ti,tilcdc,slave"; + i2c = <&i2c0>; + pinctrl-names = "default"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt new file mode 100644 index 00000000000..a58ae7756fc --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt @@ -0,0 +1,21 @@ +Device-Tree bindings for tilcdc DRM TFP410 output driver + +Required properties: + - compatible: value should be "ti,tilcdc,tfp410". + - i2c: the phandle for the i2c device to use for DDC + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + - powerdn-gpio: the powerdown GPIO, pulled low to power down the + TFP410 device (for DPMS_OFF) + +Example: + + dvicape { + compatible = "ti,tilcdc,tfp410"; + i2c = <&i2c2>; + pinctrl-names = "default"; + pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>; + powerdn-gpio = <&gpio2 31 0>; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt new file mode 100644 index 00000000000..e5f130159ae --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt @@ -0,0 +1,21 @@ +Device-Tree bindings for tilcdc DRM driver + +Required properties: + - compatible: value should be "ti,am33xx-tilcdc". + - interrupts: the interrupt number + - reg: base address and size of the LCDC device + +Recommended properties: + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + - ti,hwmods: Name of the hwmod associated to the LCDC + +Example: + + fb: fb@4830e000 { + compatible = "ti,am33xx-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + }; diff --git a/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt new file mode 100644 index 00000000000..e9de3756752 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt @@ -0,0 +1,20 @@ +Broadcom BCM2835 I2C controller + +Required properties: +- compatible : Should be "brcm,bcm2835-i2c". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks : The clock feeding the I2C controller. + +Recommended properties: +- clock-frequency : desired I2C bus clock frequency in Hz. + +Example: + +i2c@20205000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e205000 0x1000>; + interrupts = <2 21>; + clocks = <&clk_i2c>; + clock-frequency = <100000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index e9611ace879..f98d4c5b5cc 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -8,6 +8,8 @@ Required properties: (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used inside HDMIPHY block found on several samsung SoCs + (d) "samsung, exynos5440-i2c", for s3c2440-like i2c used + on EXYNOS5440 which does not need GPIO configuration. - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. diff --git a/Documentation/devicetree/bindings/leds/leds-pwm.txt b/Documentation/devicetree/bindings/leds/leds-pwm.txt new file mode 100644 index 00000000000..7297107cf83 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-pwm.txt @@ -0,0 +1,48 @@ +LED connected to PWM + +Required properties: +- compatible : should be "pwm-leds". + +Each LED is represented as a sub-node of the pwm-leds device. Each +node's name represents the name of the corresponding LED. + +LED sub-node properties: +- pwms : PWM property to point to the PWM device (phandle)/port (id) and to + specify the period time to be used: <&phandle id period_ns>; +- pwm-names : (optional) Name to be used by the PWM subsystem for the PWM device + For the pwms and pwm-names property please refer to: + Documentation/devicetree/bindings/pwm/pwm.txt +- max-brightness : Maximum brightness possible for the LED +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +twl_pwm: pwm { + /* provides two PWMs (id 0, 1 for PWM1 and PWM2) */ + compatible = "ti,twl6030-pwm"; + #pwm-cells = <2>; +}; + +twl_pwmled: pwmled { + /* provides one PWM (id 0 for Charing indicator LED) */ + compatible = "ti,twl6030-pwmled"; + #pwm-cells = <2>; +}; + +pwmleds { + compatible = "pwm-leds"; + kpad { + label = "omap4::keypad"; + pwms = <&twl_pwm 0 7812500>; + max-brightness = <127>; + }; + + charging { + label = "omap4:green:chrg"; + pwms = <&twl_pwmled 0 7812500>; + max-brightness = <255>; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/tca6507.txt b/Documentation/devicetree/bindings/leds/tca6507.txt new file mode 100644 index 00000000000..2b6693b972f --- /dev/null +++ b/Documentation/devicetree/bindings/leds/tca6507.txt @@ -0,0 +1,33 @@ +LEDs conected to tca6507 + +Required properties: +- compatible : should be : "ti,tca6507". + +Each led is represented as a sub-node of the ti,tca6507 device. + +LED sub-node properties: +- label : (optional) see Documentation/devicetree/bindings/leds/common.txt +- reg : number of LED line (could be from 0 to 6) +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + +Examples: + +tca6507@45 { + compatible = "ti,tca6507"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x45>; + + led0: red-aux@0 { + label = "red:aux"; + reg = <0x0>; + }; + + led1: green-aux@1 { + label = "green:aux"; + reg = <0x5>; + linux,default-trigger = "default-on"; + }; +}; + diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt new file mode 100644 index 00000000000..56e726ef4bf --- /dev/null +++ b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt @@ -0,0 +1,16 @@ +Device-Tree bindings for GPIO IR receiver + +Required properties: + - compatible: should be "gpio-ir-receiver". + - gpios: specifies GPIO used for IR signal reception. + +Optional properties: + - linux,rc-map-name: Linux specific remote control map name. + +Example node: + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio0 19 1>; + linux,rc-map-name = "rc-rc6-mce"; + }; diff --git a/Documentation/devicetree/bindings/mfd/max8925.txt b/Documentation/devicetree/bindings/mfd/max8925.txt new file mode 100644 index 00000000000..4f0dc6638e5 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8925.txt @@ -0,0 +1,64 @@ +* Maxim max8925 Power Management IC + +Required parent device properties: +- compatible : "maxim,max8925" +- reg : the I2C slave address for the max8925 chip +- interrupts : IRQ line for the max8925 chip +- interrupt-controller: describes the max8925 as an interrupt + controller (has its own domain) +- #interrupt-cells : should be 1. + - The cell is the max8925 local IRQ number + +Optional parent device properties: +- maxim,tsc-irq: there are 2 IRQ lines for max8925, one is indicated in + interrupts property, the other is indicated here. + +max8925 consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +max8925-onkey : : On key +max8925-rtc : : RTC +max8925-regulator : : Regulators +max8925-backlight : : Backlight +max8925-touch : : Touchscreen +max8925-power : : Charger + +Example: + + pmic: max8925@3c { + compatible = "maxim,max8925"; + reg = <0x3c>; + interrupts = <1>; + interrupt-parent = <&intcmux4>; + interrupt-controller; + #interrupt-cells = <1>; + maxim,tsc-irq = <0>; + + regulators { + SDV1 { + regulator-min-microvolt = <637500>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO1 { + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <3900000>; + regulator-boot-on; + regulator-always-on; + }; + + }; + backlight { + maxim,max8925-dual-string = <0>; + }; + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt new file mode 100644 index 00000000000..59476fbdbfa --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt @@ -0,0 +1,18 @@ +Broadcom BCM2835 SDHCI controller + +This file documents differences between the core properties described +by mmc.txt and the properties that represent the BCM2835 controller. + +Required properties: +- compatible : Should be "brcm,bcm2835-sdhci". +- clocks : The clock feeding the SDHCI controller. + +Example: + +sdhci: sdhci { + compatible = "brcm,bcm2835-sdhci"; + reg = <0x7e300000 0x100>; + interrupts = <2 30>; + clocks = <&clk_mmc>; + bus-width = <4>; +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index a591c6741d7..85aada2263d 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -6,23 +6,45 @@ Interpreted by the OF core: - reg: Registers location and length. - interrupts: Interrupts used by the MMC controller. -Required properties: -- bus-width: Number of data lines, can be <1>, <4>, or <8> - Card detection: -If no property below is supplied, standard SDHCI card detect is used. +If no property below is supplied, host native card detect is used. Only one of the properties in this section should be supplied: - broken-cd: There is no card detection available; polling must be used. - cd-gpios: Specify GPIOs for card detection, see gpio binding - non-removable: non-removable slot (like eMMC); assume always present. Optional properties: +- bus-width: Number of data lines, can be <1>, <4>, or <8>. The default + will be <1> if the property is absent. - wp-gpios: Specify GPIOs for write protection, see gpio binding -- cd-inverted: when present, polarity on the cd gpio line is inverted -- wp-inverted: when present, polarity on the wp gpio line is inverted +- cd-inverted: when present, polarity on the CD line is inverted. See the note + below for the case, when a GPIO is used for the CD line +- wp-inverted: when present, polarity on the WP line is inverted. See the note + below for the case, when a GPIO is used for the WP line - max-frequency: maximum operating clock frequency - no-1-8-v: when present, denotes that 1.8v card voltage is not supported on this system, even if the controller claims it is. +- cap-sd-highspeed: SD high-speed timing is supported +- cap-mmc-highspeed: MMC high-speed timing is supported +- cap-power-off-card: powering off the card is safe +- cap-sdio-irq: enable SDIO IRQ signalling on this interface + +*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line +polarity properties, we have to fix the meaning of the "normal" and "inverted" +line levels. We choose to follow the SDHCI standard, which specifies both those +lines as "active low." Therefore, using the "cd-inverted" property means, that +the CD line is active high, i.e. it is high, when a card is inserted. Similar +logic applies to the "wp-inverted" property. + +CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs, +specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of +dedicated pins can be specified, using *-inverted properties. GPIO polarity can +also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity +in the latter case. We choose to use the XOR logic for GPIO CD and WP lines. +This means, the two properties are "superimposed," for example leaving the +OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted +property results in a double-inversion and actually means the "normal" line +polarity is in effect. Optional SDIO properties: - keep-power-in-suspend: Preserves card power during a suspend/resume cycle diff --git a/Documentation/devicetree/bindings/mmc/orion-sdio.txt b/Documentation/devicetree/bindings/mmc/orion-sdio.txt new file mode 100644 index 00000000000..84f0ebd67a1 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/orion-sdio.txt @@ -0,0 +1,17 @@ +* Marvell orion-sdio controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the orion-sdio driver. + +- compatible: Should be "marvell,orion-sdio" +- clocks: reference to the clock of the SDIO interface + +Example: + + mvsdio@d00d4000 { + compatible = "marvell,orion-sdio"; + reg = <0xd00d4000 0x200>; + interrupts = <54>; + clocks = <&gateclk 17>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index 06cd32d0805..726fd2122a1 100644 --- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt @@ -26,8 +26,16 @@ Required Properties: * bus-width: as documented in mmc core bindings. * wp-gpios: specifies the write protect gpio line. The format of the - gpio specifier depends on the gpio controller. If the write-protect - line is not available, this property is optional. + gpio specifier depends on the gpio controller. If a GPIO is not used + for write-protect, this property is optional. + + * disable-wp: If the wp-gpios property isn't present then (by default) + we'd assume that the write protect is hooked up directly to the + controller's special purpose write protect line (accessible via + the WRTPRT register). However, it's possible that we simply don't + want write protect. In that case specify 'disable-wp'. + NOTE: This property is not required for slots known to always + connect to eMMC or SDIO cards. Optional properties: diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt new file mode 100644 index 00000000000..df204e18e03 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -0,0 +1,20 @@ +* Toshiba Mobile IO SD/MMC controller + +The tmio-mmc driver doesn't probe its devices actively, instead its binding to +devices is managed by either MFD drivers or by the sh_mobile_sdhi platform +driver. Those drivers supply the tmio-mmc driver with platform data, that either +describe hardware capabilities, known to them, or are obtained by them from +their own platform data or from their DT information. In the latter case all +compulsory and any optional properties, common to all SD/MMC drivers, as +described in mmc.txt, can be used. Additionally the following tmio_mmc-specific +optional bindings can be used. + +Optional properties: +- toshiba,mmc-wrprotect-disable: write-protect detection is unavailable + +When used with Renesas SDHI hardware, the following compatibility strings +configure various model-specific properties: + +"renesas,sh7372-sdhi": (default) compatible with SH7372 +"renesas,r8a7740-sdhi": compatible with R8A7740: certain MMC/SD commands have to + wait for the interface to become idle. diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index e3ea32e7de3..2240ac09f6b 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -1,7 +1,7 @@ * FSMC NAND Required properties: -- compatible : "st,spear600-fsmc-nand" +- compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand" - reg : Address range of the mtd chip - reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd" diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt new file mode 100644 index 00000000000..e7f8d7ed47e --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -0,0 +1,80 @@ +Device tree bindings for GPMC connected NANDs + +GPMC connected NAND (found on OMAP boards) are represented as child nodes of +the GPMC controller with a name of "nand". + +All timing relevant properties as well as generic gpmc child properties are +explained in a separate documents - please refer to +Documentation/devicetree/bindings/bus/ti-gpmc.txt + +For NAND specific properties such as ECC modes or bus width, please refer to +Documentation/devicetree/bindings/mtd/nand.txt + + +Required properties: + + - reg: The CS line the peripheral is connected to + +Optional properties: + + - nand-bus-width: Set this numeric value to 16 if the hardware + is wired that way. If not specified, a bus + width of 8 is assumed. + + - ti,nand-ecc-opt: A string setting the ECC layout to use. One of: + + "sw" Software method (default) + "hw" Hardware method + "hw-romcode" gpmc hamming mode method & romcode layout + "bch4" 4-bit BCH ecc code + "bch8" 8-bit BCH ecc code + + - elm_id: Specifies elm device node. This is required to support BCH + error correction using ELM module. + +For inline partiton table parsing (optional): + + - #address-cells: should be set to 1 + - #size-cells: should be set to 1 + +Example for an AM33xx board: + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x50000000 0x1000000>; + interrupts = <100>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */ + elm_id = <&elm>; + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + + gpmc,sync-clk = <0>; + gpmc,cs-on = <0>; + gpmc,cs-rd-off = <44>; + gpmc,cs-wr-off = <44>; + gpmc,adv-on = <6>; + gpmc,adv-rd-off = <34>; + gpmc,adv-wr-off = <44>; + gpmc,we-off = <40>; + gpmc,oe-off = <54>; + gpmc,access = <64>; + gpmc,rd-cycle = <82>; + gpmc,wr-cycle = <82>; + gpmc,wr-access = <40>; + gpmc,wr-data-mux-bus = <0>; + + #address-cells = <1>; + #size-cells = <1>; + + /* partitions go here */ + }; + }; + diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt new file mode 100644 index 00000000000..deec9da224a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt @@ -0,0 +1,43 @@ +Device tree bindings for GPMC connected OneNANDs + +GPMC connected OneNAND (found on OMAP boards) are represented as child nodes of +the GPMC controller with a name of "onenand". + +All timing relevant properties as well as generic gpmc child properties are +explained in a separate documents - please refer to +Documentation/devicetree/bindings/bus/ti-gpmc.txt + +Required properties: + + - reg: The CS line the peripheral is connected to + +Optional properties: + + - dma-channel: DMA Channel index + +For inline partiton table parsing (optional): + + - #address-cells: should be set to 1 + - #size-cells: should be set to 1 + +Example for an OMAP3430 board: + + gpmc: gpmc@6e000000 { + compatible = "ti,omap3430-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x6e000000 0x1000000>; + interrupts = <20>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + #address-cells = <2>; + #size-cells = <1>; + + onenand@0 { + reg = <0 0 0>; /* CS0, offset 0 */ + + #address-cells = <1>; + #size-cells = <1>; + + /* partitions go here */ + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index e97a27856b2..4598a47aa0c 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -7,9 +7,9 @@ on-chip controllers onto these pads. Required Properties: - compatible: should be one of the following. - - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller. - - "samsung,pinctrl-exynos4x12": for Exynos4x12 compatible pin-controller. - - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller. + - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. + - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. + - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller. - reg: Base address of the pin controller hardware module and length of the address space it occupies. @@ -142,7 +142,7 @@ the following format 'pinctrl{n}' where n is a unique number for the alias. Example: A pin-controller node with pin banks: pinctrl_0: pinctrl@11400000 { - compatible = "samsung,pinctrl-exynos4210"; + compatible = "samsung,exynos4210-pinctrl"; reg = <0x11400000 0x1000>; interrupts = <0 47 0>; @@ -185,7 +185,7 @@ Example: A pin-controller node with pin banks: Example 1: A pin-controller node with pin groups. pinctrl_0: pinctrl@11400000 { - compatible = "samsung,pinctrl-exynos4210"; + compatible = "samsung,exynos4210-pinctrl"; reg = <0x11400000 0x1000>; interrupts = <0 47 0>; @@ -230,7 +230,7 @@ Example 1: A pin-controller node with pin groups. Example 2: A pin-controller node with external wakeup interrupt controller node. pinctrl_1: pinctrl@11000000 { - compatible = "samsung,pinctrl-exynos4210"; + compatible = "samsung,exynos4210-pinctrl"; reg = <0x11000000 0x1000>; interrupts = <0 46 0> diff --git a/Documentation/devicetree/bindings/power_supply/max8925_batter.txt b/Documentation/devicetree/bindings/power_supply/max8925_batter.txt new file mode 100644 index 00000000000..d7e3e0c0f71 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/max8925_batter.txt @@ -0,0 +1,18 @@ +max8925-battery bindings +~~~~~~~~~~~~~~~~ + +Optional properties : + - batt-detect: whether support battery detect + - topoff-threshold: set charging current in topoff mode + - fast-charge: set charging current in fast mode + - no-temp-support: whether support temperature protection detect + - no-insert-detect: whether support insert detect + +Example: + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt index 9e7a2417dac..7f150b5012c 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/guts.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/guts.txt @@ -17,9 +17,20 @@ Recommended properties: contains a functioning "reset control register" (i.e. the board is wired to reset upon setting the HRESET_REQ bit in this register). -Example: + - fsl,liodn-bits : Indicates the number of defined bits in the LIODN + registers, for those SOCs that have a PAMU device. + +Examples: global-utilities@e0000 { /* global utilities block */ compatible = "fsl,mpc8548-guts"; reg = <e0000 1000>; fsl,has-rstcr; }; + + guts: global-utilities@e0000 { + compatible = "fsl,qoriq-device-config-1.0"; + reg = <0xe0000 0xe00>; + fsl,has-rstcr; + #sleep-cells = <1>; + fsl,liodn-bits = <12>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt b/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt new file mode 100644 index 00000000000..1f5e329f756 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/pamu.txt @@ -0,0 +1,140 @@ +Freescale Peripheral Management Access Unit (PAMU) Device Tree Binding + +DESCRIPTION + +The PAMU is an I/O MMU that provides device-to-memory access control and +address translation capabilities. + +Required properties: + +- compatible : <string> + First entry is a version-specific string, such as + "fsl,pamu-v1.0". The second is "fsl,pamu". +- ranges : <prop-encoded-array> + A standard property. Utilized to describe the memory mapped + I/O space utilized by the controller. The size should + be set to the total size of the register space of all + physically present PAMU controllers. For example, for + PAMU v1.0, on an SOC that has five PAMU devices, the size + is 0x5000. +- interrupts : <prop-encoded-array> + Interrupt mappings. The first tuple is the normal PAMU + interrupt, used for reporting access violations. The second + is for PAMU hardware errors, such as PAMU operation errors + and ECC errors. +- #address-cells: <u32> + A standard property. +- #size-cells : <u32> + A standard property. + +Optional properties: +- reg : <prop-encoded-array> + A standard property. It represents the CCSR registers of + all child PAMUs combined. Include it to provide support + for legacy drivers. +- interrupt-parent : <phandle> + Phandle to interrupt controller + +Child nodes: + +Each child node represents one PAMU controller. Each SOC device that is +connected to a specific PAMU device should have a "fsl,pamu-phandle" property +that links to the corresponding specific child PAMU controller. + +- reg : <prop-encoded-array> + A standard property. Specifies the physical address and + length (relative to the parent 'ranges' property) of this + PAMU controller's configuration registers. The size should + be set to the size of this PAMU controllers's register space. + For PAMU v1.0, this size is 0x1000. +- fsl,primary-cache-geometry + : <prop-encoded-array> + Two cells that specify the geometry of the primary PAMU + cache. The first is the number of cache lines, and the + second is the number of "ways". For direct-mapped caches, + specify a value of 1. +- fsl,secondary-cache-geometry + : <prop-encoded-array> + Two cells that specify the geometry of the secondary PAMU + cache. The first is the number of cache lines, and the + second is the number of "ways". For direct-mapped caches, + specify a value of 1. + +Device nodes: + +Devices that have LIODNs need to specify links to the parent PAMU controller +(the actual PAMU controller that this device is connected to) and a pointer to +the LIODN register, if applicable. + +- fsl,iommu-parent + : <phandle> + Phandle to the single, specific PAMU controller node to which + this device is connect. The PAMU topology is represented in + the device tree to assist code that dynamically determines the + best LIODN values to minimize PAMU cache thrashing. + +- fsl,liodn-reg : <prop-encoded-array> + Two cells that specify the location of the LIODN register + for this device. Required for devices that have a single + LIODN. The first cell is a phandle to a node that contains + the registers where the LIODN is to be set. The second is + the offset from the first "reg" resource of the node where + the specific LIODN register is located. + + +Example: + + iommu@20000 { + compatible = "fsl,pamu-v1.0", "fsl,pamu"; + reg = <0x20000 0x5000>; + ranges = <0 0x20000 0x5000>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = < + 24 2 0 0 + 16 2 1 30>; + + pamu0: pamu@0 { + reg = <0 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu1: pamu@1000 { + reg = <0x1000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu2: pamu@2000 { + reg = <0x2000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu3: pamu@3000 { + reg = <0x3000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + + pamu4: pamu@4000 { + reg = <0x4000 0x1000>; + fsl,primary-cache-geometry = <32 1>; + fsl,secondary-cache-geometry = <128 2>; + }; + }; + + guts: global-utilities@e0000 { + compatible = "fsl,qoriq-device-config-1.0"; + reg = <0xe0000 0xe00>; + fsl,has-rstcr; + #sleep-cells = <1>; + fsl,liodn-bits = <12>; + }; + +/include/ "qoriq-dma-0.dtsi" + dma@100300 { + fsl,iommu-parent = <&pamu0>; + fsl,liodn-reg = <&guts 0x584>; /* DMA2LIODNR */ + }; diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt new file mode 100644 index 00000000000..de0eaed8665 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt @@ -0,0 +1,18 @@ +Atmel TCB PWM controller + +Required properties: +- compatible: should be "atmel,tcb-pwm" +- #pwm-cells: Should be 3. The first cell specifies the per-chip index + of the PWM to use, the second cell is the period in nanoseconds and + bit 0 in the third cell is used to encode the polarity of PWM output. + Set bit 0 of the third cell in PWM specifier to 1 for inverse polarity & + set to 0 for normal polarity. +- tc-block: The Timer Counter block to use as a PWM chip. + +Example: + +pwm { + compatible = "atmel,tcb-pwm"; + #pwm-cells = <3>; + tc-block = <1>; +}; diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt index bcc63678a9a..d21d82d2985 100644 --- a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -3,14 +3,17 @@ VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller Required properties: - compatible: should be "via,vt8500-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: should be 2. The first cell specifies the per-chip index - of the PWM to use and the second cell is the period in nanoseconds. +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. - clocks: phandle to the PWM source clock Example: pwm1: pwm@d8220000 { - #pwm-cells = <2>; + #pwm-cells = <3>; compatible = "via,vt8500-pwm"; reg = <0xd8220000 0x1000>; clocks = <&clkpwm>; diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt new file mode 100644 index 00000000000..313a60ba61d --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -0,0 +1,122 @@ +TPS65090 regulators + +Required properties: +- compatible: "ti,tps65090" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + dcdc[1-3], fet[1-7] and ldo[1-2] respectively. +- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively. +- infet[1-7]-supply: The input supply for FET[1-7] respectively. +- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively. + +Optional properties: +- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled then this property should be there. +- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3. + If DCDCs are externally controlled and if it is from GPIO then GPIO + number should be provided. If it is externally controlled and no GPIO + entry then driver will just configure this rails as external control + and will not provide any enable/disable APIs. + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps65090@48 { + compatible = "ti,tps65090"; + reg = <0x48>; + interrupts = <0 88 0x4>; + + vsys1-supply = <&some_reg>; + vsys2-supply = <&some_reg>; + vsys3-supply = <&some_reg>; + infet1-supply = <&some_reg>; + infet2-supply = <&some_reg>; + infet3-supply = <&some_reg>; + infet4-supply = <&some_reg>; + infet5-supply = <&some_reg>; + infet6-supply = <&some_reg>; + infet7-supply = <&some_reg>; + vsys_l1-supply = <&some_reg>; + vsys_l2-supply = <&some_reg>; + + regulators { + dcdc1 { + regulator-name = "dcdc1"; + regulator-boot-on; + regulator-always-on; + ti,enable-ext-control; + dcdc-ext-control-gpios = <&gpio 10 0>; + }; + + dcdc2 { + regulator-name = "dcdc2"; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3 { + regulator-name = "dcdc3"; + regulator-boot-on; + regulator-always-on; + }; + + fet1 { + regulator-name = "fet1"; + regulator-boot-on; + regulator-always-on; + }; + + fet2 { + regulator-name = "fet2"; + regulator-boot-on; + regulator-always-on; + }; + + fet3 { + regulator-name = "fet3"; + regulator-boot-on; + regulator-always-on; + }; + + fet4 { + regulator-name = "fet4"; + regulator-boot-on; + regulator-always-on; + }; + + fet5 { + regulator-name = "fet5"; + regulator-boot-on; + regulator-always-on; + }; + + fet6 { + regulator-name = "fet6"; + regulator-boot-on; + regulator-always-on; + }; + + fet7 { + regulator-name = "fet7"; + regulator-boot-on; + regulator-always-on; + }; + + ldo1 { + regulator-name = "ldo1"; + regulator-boot-on; + regulator-always-on; + }; + + ldo2 { + regulator-name = "ldo2"; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt new file mode 100644 index 00000000000..392a4493eeb --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt @@ -0,0 +1,24 @@ +NVIDIA Tegra20/Tegra30 high speed (DMA based) UART controller driver. + +Required properties: +- compatible : should be "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart". +- reg: Should contain UART controller registers location and length. +- interrupts: Should contain UART controller interrupts. +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this UART controller. + +Optional properties: +- nvidia,enable-modem-interrupt: Enable modem interrupts. Should be enable + only if all 8 lines of UART controller are pinmuxed. + +Example: + +serial@70006000 { + compatible = "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart"; + reg = <0x70006000 0x40>; + reg-shift = <2>; + interrupts = <0 36 0x04>; + nvidia,dma-request-selector = <&apbdma 8>; + nvidia,enable-modem-interrupt; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/sound/ak4642.txt b/Documentation/devicetree/bindings/sound/ak4642.txt new file mode 100644 index 00000000000..623d4e70ae1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ak4642.txt @@ -0,0 +1,17 @@ +AK4642 I2C transmitter + +This device supports I2C mode only. + +Required properties: + + - compatible : "asahi-kasei,ak4642" or "asahi-kasei,ak4643" or "asahi-kasei,ak4648" + - reg : The chip select number on the I2C bus + +Example: + +&i2c { + ak4648: ak4648@0x12 { + compatible = "asahi-kasei,ak4642"; + reg = <0x12>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index a850fb9c88e..e2cd1d7539e 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -20,6 +20,18 @@ Optional properties: !RESET pin - cirrus,amuteb-eq-bmutec: When given, the Codec's AMUTEB=BMUTEC flag is enabled. + - cirrus,enable-soft-reset: + The CS4271 requires its LRCLK and MCLK to be stable before its RESET + line is de-asserted. That also means that clocks cannot be changed + without putting the chip back into hardware reset, which also requires + a complete re-initialization of all registers. + + One (undocumented) workaround is to assert and de-assert the PDN bit + in the MODE2 register. This workaround can be enabled with this DT + property. + + Note that this is not needed in case the clocks are stable + throughout the entire runtime of the codec. Examples: diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt new file mode 100644 index 00000000000..be35d34e8b2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt @@ -0,0 +1,51 @@ +NVIDIA Tegra audio complex + +Required properties: +- compatible : "nvidia,tegra-audio-wm9712" +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the WM9712's pins, and the jacks on the board: + + WM9712 pins: + + * MONOOUT + * HPOUTL + * HPOUTR + * LOUT2 + * ROUT2 + * OUT3 + * LINEINL + * LINEINR + * PHONE + * PCBEEP + * MIC1 + * MIC2 + * Mic Bias + + Board connectors: + + * Headphone + * LineIn + * Mic + +- nvidia,ac97-controller : The phandle of the Tegra AC97 controller + + +Example: + +sound { + compatible = "nvidia,tegra-audio-wm9712-colibri_t20", + "nvidia,tegra-audio-wm9712"; + nvidia,model = "Toradex Colibri T20"; + + nvidia,audio-routing = + "Headphone", "HPOUTL", + "Headphone", "HPOUTR", + "LineIn", "LINEINL", + "LineIn", "LINEINR", + "Mic", "MIC1"; + + nvidia,ac97-controller = <&ac97>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt new file mode 100644 index 00000000000..c1454979c1e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt @@ -0,0 +1,22 @@ +NVIDIA Tegra 20 AC97 controller + +Required properties: +- compatible : "nvidia,tegra20-ac97" +- reg : Should contain AC97 controller registers location and length +- interrupts : Should contain AC97 interrupt +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for the AC97 controller +- nvidia,codec-reset-gpio : The Tegra GPIO controller's phandle and the number + of the GPIO used to reset the external AC97 codec +- nvidia,codec-sync-gpio : The Tegra GPIO controller's phandle and the number + of the GPIO corresponding with the AC97 DAP _FS line +Example: + +ac97@70002000 { + compatible = "nvidia,tegra20-ac97"; + reg = <0x70002000 0x200>; + interrupts = <0 81 0x04>; + nvidia,dma-request-selector = <&apbdma 12>; + nvidia,codec-reset-gpio = <&gpio 170 0>; + nvidia,codec-sync-gpio = <&gpio 120 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-twl4030.txt b/Documentation/devicetree/bindings/sound/omap-twl4030.txt index 6fae51c7f76..1ab6bc8404d 100644 --- a/Documentation/devicetree/bindings/sound/omap-twl4030.txt +++ b/Documentation/devicetree/bindings/sound/omap-twl4030.txt @@ -6,6 +6,52 @@ Required properties: - ti,mcbsp: phandle for the McBSP node - ti,codec: phandle for the twl4030 audio node +Optional properties: +- ti,mcbsp-voice: phandle for the McBSP node connected to the voice port of twl +- ti, jack-det-gpio: Jack detect GPIO +- ti,audio-routing: List of connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. + If the routing is not provided all possible connection will be available + +Available audio endpoints for the audio-routing table: + +Board connectors: + * Headset Stereophone + * Earpiece Spk + * Handsfree Spk + * Ext Spk + * Main Mic + * Sub Mic + * Headset Mic + * Carkit Mic + * Digital0 Mic + * Digital1 Mic + * Line In + +twl4030 pins: + * HSOL + * HSOR + * EARPIECE + * HFL + * HFR + * PREDRIVEL + * PREDRIVER + * CARKITL + * CARKITR + * MAINMIC + * SUBMIC + * HSMIC + * DIGIMIC0 + * DIGIMIC1 + * CARKITMIC + * AUXL + * AUXR + + * Headset Mic Bias + * Mic Bias 1 /* Used for Main Mic or Digimic0 */ + * Mic Bias 2 /* Used for Sub Mic or Digimic1 */ + Example: sound { diff --git a/Documentation/devicetree/bindings/sound/renesas,fsi.txt b/Documentation/devicetree/bindings/sound/renesas,fsi.txt new file mode 100644 index 00000000000..c5be003f413 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/renesas,fsi.txt @@ -0,0 +1,26 @@ +Renesas FSI + +Required properties: +- compatible : "renesas,sh_fsi2" or "renesas,sh_fsi" +- reg : Should contain the register physical address and length +- interrupts : Should contain FSI interrupt + +- fsia,spdif-connection : FSI is connected by S/PDFI +- fsia,stream-mode-support : FSI supports 16bit stream mode. +- fsia,use-internal-clock : FSI uses internal clock when master mode. + +- fsib,spdif-connection : same as fsia +- fsib,stream-mode-support : same as fsia +- fsib,use-internal-clock : same as fsia + +Example: + +sh_fsi2: sh_fsi2@0xec230000 { + compatible = "renesas,sh_fsi2"; + reg = <0xec230000 0x400>; + interrupts = <0 146 0x4>; + + fsia,spdif-connection; + fsia,stream-mode-support; + fsia,use-internal-clock; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt b/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt new file mode 100644 index 00000000000..4686646fb12 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt @@ -0,0 +1,14 @@ +Samsung SMDK audio complex + +Required properties: +- compatible : "samsung,smdk-wm8994" +- samsung,i2s-controller: The phandle of the Samsung I2S0 controller +- samsung,audio-codec: The phandle of the WM8994 audio codec +Example: + +sound { + compatible = "samsung,smdk-wm8994"; + + samsung,i2s-controller = <&i2s0>; + samsung,audio-codec = <&wm8994>; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt new file mode 100644 index 00000000000..3070046da2e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt @@ -0,0 +1,63 @@ +* Samsung I2S controller + +Required SoC Specific Properties: + +- compatible : "samsung,i2s-v5" +- reg: physical base address of the controller and length of memory mapped + region. +- dmas: list of DMA controller phandle and DMA request line ordered pairs. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. + +Optional SoC Specific Properties: + +- samsung,supports-6ch: If the I2S Primary sound source has 5.1 Channel + support, this flag is enabled. +- samsung,supports-rstclr: This flag should be set if I2S software reset bit + control is required. When this flag is set I2S software reset bit will be + enabled or disabled based on need. +- samsung,supports-secdai:If I2S block has a secondary FIFO and internal DMA, + then this flag is enabled. +- samsung,idma-addr: Internal DMA register base address of the audio + sub system(used in secondary sound source). + +Required Board Specific Properties: + +- gpios: The gpio specifier for data out,data in, LRCLK, CDCLK and SCLK + interface lines. The format of the gpio specifier depends on the gpio + controller. + The syntax of samsung gpio specifier is + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + [drive strength]> + +Example: + +- SoC Specific Portion: + +i2s@03830000 { + compatible = "samsung,i2s-v5"; + reg = <0x03830000 0x100>; + dmas = <&pdma0 10 + &pdma0 9 + &pdma0 8>; + dma-names = "tx", "rx", "tx-sec"; + samsung,supports-6ch; + samsung,supports-rstclr; + samsung,supports-secdai; + samsung,idma-addr = <0x03000000>; +}; + +- Board Specific Portion: + +i2s@03830000 { + gpios = <&gpz 0 2 0 0>, /* I2S_0_SCLK */ + <&gpz 1 2 0 0>, /* I2S_0_CDCLK */ + <&gpz 2 2 0 0>, /* I2S_0_LRCK */ + <&gpz 3 2 0 0>, /* I2S_0_SDI */ + <&gpz 4 2 0 0>, /* I2S_0_SDO[1] */ + <&gpz 5 2 0 0>, /* I2S_0_SDO[2] */ + <&gpz 6 2 0 0>; /* I2S_0_SDO[3] */ +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index e7b98f41fa5..f47c3f589fd 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -11,6 +11,12 @@ Optional properties: - gpio-reset - gpio pin number used for codec reset - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality +- ai3x-micbias-vg - MicBias Voltage required. + 1 - MICBIAS output is powered to 2.0V, + 2 - MICBIAS output is powered to 2.5V, + 3 - MICBIAS output is connected to AVDD, + If this node is not mentioned or if the value is incorrect, then MicBias + is powered down. Example: diff --git a/Documentation/devicetree/bindings/sound/wm8962.txt b/Documentation/devicetree/bindings/sound/wm8962.txt new file mode 100644 index 00000000000..dceb3b1c2bb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8962.txt @@ -0,0 +1,16 @@ +WM8962 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8962" + + - reg : the I2C address of the device. + +Example: + +codec: wm8962@1a { + compatible = "wlf,wm8962"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt index 801d58cb6d4..46882058b59 100644 --- a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt +++ b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt @@ -5,6 +5,12 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain the LRADC interrupts +Optional properties: +- fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen + to LRADC. Valid value is either 4 or 5. If this + property is not present, then the touchscreen is + disabled. + Examples: lradc@80050000 { diff --git a/Documentation/devicetree/bindings/thermal/dove-thermal.txt b/Documentation/devicetree/bindings/thermal/dove-thermal.txt new file mode 100644 index 00000000000..6f474677d47 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/dove-thermal.txt @@ -0,0 +1,18 @@ +* Dove Thermal + +This driver is for Dove SoCs which contain a thermal sensor. + +Required properties: +- compatible : "marvell,dove-thermal" +- reg : Address range of the thermal registers + +The reg properties should contain two ranges. The first is for the +three Thermal Manager registers, while the second range contains the +Thermal Diode Control Registers. + +Example: + + thermal@10078 { + compatible = "marvell,dove-thermal"; + reg = <0xd001c 0x0c>, <0xd005c 0x08>; + }; diff --git a/Documentation/devicetree/bindings/thermal/kirkwood-thermal.txt b/Documentation/devicetree/bindings/thermal/kirkwood-thermal.txt new file mode 100644 index 00000000000..8c0f5eb86da --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/kirkwood-thermal.txt @@ -0,0 +1,15 @@ +* Kirkwood Thermal + +This version is for Kirkwood 88F8262 & 88F6283 SoCs. Other kirkwoods +don't contain a thermal sensor. + +Required properties: +- compatible : "marvell,kirkwood-thermal" +- reg : Address range of the thermal registers + +Example: + + thermal@10078 { + compatible = "marvell,kirkwood-thermal"; + reg = <0x10078 0x4>; + }; diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt new file mode 100644 index 00000000000..28ef498a66e --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -0,0 +1,29 @@ +* Renesas R-Car Thermal + +Required properties: +- compatible : "renesas,rcar-thermal" +- reg : Address range of the thermal registers. + The 1st reg will be recognized as common register + if it has "interrupts". + +Option properties: + +- interrupts : use interrupt + +Example (non interrupt support): + +thermal@e61f0100 { + compatible = "renesas,rcar-thermal"; + reg = <0xe61f0100 0x38>; +}; + +Example (interrupt support): + +thermal@e61f0000 { + compatible = "renesas,rcar-thermal"; + reg = <0xe61f0000 0x14 + 0xe61f0100 0x38 + 0xe61f0200 0x38 + 0xe61f0300 0x38>; + interrupts = <0 69 4>; +}; diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt b/Documentation/devicetree/bindings/timer/marvell,armada-370-xp-timer.txt index 64830118b01..36381129d14 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt +++ b/Documentation/devicetree/bindings/timer/marvell,armada-370-xp-timer.txt @@ -1,10 +1,13 @@ -Marvell Armada 370 and Armada XP Global Timers ----------------------------------------------- +Marvell Armada 370 and Armada XP Timers +--------------------------------------- Required properties: - compatible: Should be "marvell,armada-370-xp-timer" -- interrupts: Should contain the list of Global Timer interrupts -- reg: Should contain the base address of the Global Timer registers +- interrupts: Should contain the list of Global Timer interrupts and + then local timer interrupts +- reg: Should contain location and length for timers register. First + pair for the Global Timer registers, second pair for the + local/private timers. - clocks: clock driving the timer hardware Optional properties: diff --git a/Documentation/devicetree/bindings/tty/serial/arc-uart.txt b/Documentation/devicetree/bindings/tty/serial/arc-uart.txt new file mode 100644 index 00000000000..5cae2eb686f --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/arc-uart.txt @@ -0,0 +1,26 @@ +* Synopsys ARC UART : Non standard UART used in some of the ARC FPGA boards + +Required properties: +- compatible : "snps,arc-uart" +- reg : offset and length of the register set for the device. +- interrupts : device interrupt +- clock-frequency : the input clock frequency for the UART +- current-speed : baud rate for UART + +e.g. + +arcuart0: serial@c0fc1000 { + compatible = "snps,arc-uart"; + reg = <0xc0fc1000 0x100>; + interrupts = <5>; + clock-frequency = <80000000>; + current-speed = <115200>; + status = "okay"; +}; + +Note: Each port should have an alias correctly numbered in "aliases" node. + +e.g. +aliases { + serial0 = &arcuart0; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt index 6588b6950a7..8e080b893b4 100644 --- a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt +++ b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt @@ -5,10 +5,16 @@ Required properties: - reg : Address and length of the register set - interrupts : Should contain uart interrupt +Optional properties: +- location : Decides the location of the USART I/O pins. + Allowed range : [0 .. 5] + Default: 0 + Example: uart@0x4000c400 { compatible = "efm32,uart"; reg = <0x4000c400 0x400>; interrupts = <15>; + location = <0>; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt new file mode 100644 index 00000000000..7a95c651ceb --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -0,0 +1,22 @@ +synopsys DWC3 CORE + +DWC3- USB3 CONTROLLER + +Required properties: + - compatible: must be "synopsys,dwc3" + - reg : Address and length of the register set for the device + - interrupts: Interrupts used by the dwc3 controller. + - usb-phy : array of phandle for the PHY device + +Optional properties: + - tx-fifo-resize: determines if the FIFO *has* to be reallocated. + +This is usually a subnode to DWC3 glue to which it is connected. + +dwc3@4a030000 { + compatible = "synopsys,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + tx-fifo-resize; +}; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt index e9b005dc762..34c95288327 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt @@ -11,6 +11,7 @@ Required properties : - phy_type : Should be one of "ulpi" or "utmi". - nvidia,vbus-gpio : If present, specifies a gpio that needs to be activated for the bus to be powered. + - nvidia,phy : phandle of the PHY instance, the controller is connected to. Required properties for phy_type == ulpi: - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. @@ -27,3 +28,5 @@ Optional properties: registers are accessed through the APB_MISC base address instead of the USB controller. Since this is a legacy issue it probably does not warrant a compatible string of its own. + - nvidia,needs-double-reset : boolean is to be set for some of the Tegra2 + USB ports, which need reset twice due to hardware issues. diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt new file mode 100644 index 00000000000..6bdaba2f0aa --- /dev/null +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt @@ -0,0 +1,17 @@ +Tegra SOC USB PHY + +The device node for Tegra SOC USB PHY: + +Required properties : + - compatible : Should be "nvidia,tegra20-usb-phy". + - reg : Address and length of the register set for the USB PHY interface. + - phy_type : Should be one of "ulpi" or "utmi". + +Required properties for phy_type == ulpi: + - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. + +Optional properties: + - nvidia,has-legacy-mode : boolean indicates whether this controller can + operate in legacy mode (as APX 2500 / 2600). In legacy mode some + registers are accessed through the APB_MISC base address instead of + the USB controller.
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 29a043ecda5..1ef0ce71f8f 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -1,8 +1,11 @@ -OMAP GLUE +OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS OMAP MUSB GLUE - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" - ti,hwmods : must be "usb_otg_hs" + - ti,has-mailbox : to specify that omap uses an external mailbox + (in control module) to communicate with the musb core during device connect + and disconnect. - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - num_eps : Specifies the number of endpoints. This is also a @@ -16,13 +19,19 @@ OMAP MUSB GLUE - power : Should be "50". This signifies the controller can supply upto 100mA when operating in host mode. +Optional properties: + - ctrl-module : phandle of the control module this glue uses to write to + mailbox + SOC specific device node entry usb_otg_hs: usb_otg_hs@4a0ab000 { compatible = "ti,omap4-musb"; ti,hwmods = "usb_otg_hs"; + ti,has-mailbox; multipoint = <1>; num_eps = <16>; ram_bits = <12>; + ctrl-module = <&omap_control_usb>; }; Board specific device node entry @@ -31,3 +40,26 @@ Board specific device node entry mode = <3>; power = <50>; }; + +OMAP CONTROL USB + +Required properties: + - compatible: Should be "ti,omap-control-usb" + - reg : Address and length of the register set for the device. It contains + the address of "control_dev_conf" and "otghs_control" or "phy_power_usb" + depending upon omap4 or omap5. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + - ti,type: This is used to differentiate whether the control module has + usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to + notify events to the musb core and omap5 has usb3 phy power register to + power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3 + phy power. + +omap_control_usb: omap-control-usb@4a002300 { + compatible = "ti,omap-control-usb"; + reg = <0x4a002300 0x4>, + <0x4a00233c 0x4>; + reg-names = "control_dev_conf", "otghs_control"; + ti,type = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt new file mode 100644 index 00000000000..033194934f6 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt @@ -0,0 +1,55 @@ +* Samsung's usb phy transceiver + +The Samsung's phy transceiver is used for controlling usb phy for +s3c-hsotg as well as ehci-s5p and ohci-exynos usb controllers +across Samsung SOCs. +TODO: Adding the PHY binding with controller(s) according to the under +developement generic PHY driver. + +Required properties: + +Exynos4210: +- compatible : should be "samsung,exynos4210-usbphy" +- reg : base physical address of the phy registers and length of memory mapped + region. + +Exynos5250: +- compatible : should be "samsung,exynos5250-usbphy" +- reg : base physical address of the phy registers and length of memory mapped + region. + +Optional properties: +- #address-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- #size-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- ranges: allows valid translation between child's address space and parent's + address space. + +- The child node 'usbphy-sys' to the node 'usbphy' is for the system controller + interface for usb-phy. It should provide the following information required by + usb-phy controller to control phy. + - reg : base physical address of PHY_CONTROL registers. + The size of this register is the total sum of size of all PHY_CONTROL + registers that the SoC has. For example, the size will be + '0x4' in case we have only one PHY_CONTROL register (e.g. + OTHERS register in S3C64XX or USB_PHY_CONTROL register in S5PV210) + and, '0x8' in case we have two PHY_CONTROL registers (e.g. + USBDEVICE_PHY_CONTROL and USBHOST_PHY_CONTROL registers in exynos4x). + and so on. + +Example: + - Exynos4210 + + usbphy@125B0000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,exynos4210-usbphy"; + reg = <0x125B0000 0x100>; + ranges; + + usbphy-sys { + /* USB device and host PHY_CONTROL registers */ + reg = <0x10020704 0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt index 80d4148cb66..61496f5cb09 100644 --- a/Documentation/devicetree/bindings/usb/usb-phy.txt +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt @@ -4,14 +4,39 @@ OMAP USB2 PHY Required properties: - compatible: Should be "ti,omap-usb2" - - reg : Address and length of the register set for the device. Also -add the address of control module dev conf register until a driver for -control module is added + - reg : Address and length of the register set for the device. + +Optional properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. This is usually a subnode of ocp2scp to which it is connected. usb2phy@4a0ad080 { compatible = "ti,omap-usb2"; - reg = <0x4a0ad080 0x58>, - <0x4a002300 0x4>; + reg = <0x4a0ad080 0x58>; + ctrl-module = <&omap_control_usb>; +}; + +OMAP USB3 PHY + +Required properties: + - compatible: Should be "ti,omap-usb3" + - reg : Address and length of the register set for the device. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + +Optional properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +This is usually a subnode of ocp2scp to which it is connected. + +usb3phy@4a084400 { + compatible = "ti,omap-usb3"; + reg = <0x4a084400 0x80>, + <0x4a084800 0x64>, + <0x4a084c00 0x40>; + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_usb>; }; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt new file mode 100644 index 00000000000..6813a715fc7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -0,0 +1,20 @@ +SMSC USB3503 High-Speed Hub Controller + +Required properties: +- compatible: Should be "smsc,usb3503". +- reg: Specifies the i2c slave address, it should be 0x08. +- connect-gpios: Should specify GPIO for connect. +- intn-gpios: Should specify GPIO for interrupt. +- reset-gpios: Should specify GPIO for reset. +- initial-mode: Should specify initial mode. + (1 for HUB mode, 2 for STANDBY mode) + +Examples: + usb3503@08 { + compatible = "smsc,usb3503"; + reg = <0x08>; + connect-gpios = <&gpx3 0 1>; + intn-gpios = <&gpx3 4 1>; + reset-gpios = <&gpx3 5 1>; + initial-mode = <1>; + }; diff --git a/Documentation/devicetree/bindings/video/backlight/max8925-backlight.txt b/Documentation/devicetree/bindings/video/backlight/max8925-backlight.txt new file mode 100644 index 00000000000..b4cffdaa413 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/max8925-backlight.txt @@ -0,0 +1,10 @@ +88pm860x-backlight bindings + +Optional properties: + - maxim,max8925-dual-string: whether support dual string + +Example: + + backlights { + maxim,max8925-dual-string = <0>; + }; diff --git a/Documentation/devicetree/bindings/video/display-timing.txt b/Documentation/devicetree/bindings/video/display-timing.txt new file mode 100644 index 00000000000..150038552bc --- /dev/null +++ b/Documentation/devicetree/bindings/video/display-timing.txt @@ -0,0 +1,109 @@ +display-timing bindings +======================= + +display-timings node +-------------------- + +required properties: + - none + +optional properties: + - native-mode: The native mode for the display, in case multiple modes are + provided. When omitted, assume the first node is the native. + +timing subnode +-------------- + +required properties: + - hactive, vactive: display resolution + - hfront-porch, hback-porch, hsync-len: horizontal display timing parameters + in pixels + vfront-porch, vback-porch, vsync-len: vertical display timing parameters in + lines + - clock-frequency: display clock in Hz + +optional properties: + - hsync-active: hsync pulse is active low/high/ignored + - vsync-active: vsync pulse is active low/high/ignored + - de-active: data-enable pulse is active low/high/ignored + - pixelclk-active: with + - active high = drive pixel data on rising edge/ + sample data on falling edge + - active low = drive pixel data on falling edge/ + sample data on rising edge + - ignored = ignored + - interlaced (bool): boolean to enable interlaced mode + - doublescan (bool): boolean to enable doublescan mode + +All the optional properties that are not bool follow the following logic: + <1>: high active + <0>: low active + omitted: not used on hardware + +There are different ways of describing the capabilities of a display. The +devicetree representation corresponds to the one commonly found in datasheets +for displays. If a display supports multiple signal timings, the native-mode +can be specified. + +The parameters are defined as: + + +----------+-------------------------------------+----------+-------+ + | | ↑ | | | + | | |vback_porch | | | + | | ↓ | | | + +----------#######################################----------+-------+ + | # ↑ # | | + | # | # | | + | hback # | # hfront | hsync | + | porch # | hactive # porch | len | + |<-------->#<-------+--------------------------->#<-------->|<----->| + | # | # | | + | # |vactive # | | + | # | # | | + | # ↓ # | | + +----------#######################################----------+-------+ + | | ↑ | | | + | | |vfront_porch | | | + | | ↓ | | | + +----------+-------------------------------------+----------+-------+ + | | ↑ | | | + | | |vsync_len | | | + | | ↓ | | | + +----------+-------------------------------------+----------+-------+ + +Example: + + display-timings { + native-mode = <&timing0>; + timing0: 1080p24 { + /* 1920x1080p24 */ + clock-frequency = <52000000>; + hactive = <1920>; + vactive = <1080>; + hfront-porch = <25>; + hback-porch = <25>; + hsync-len = <25>; + vback-porch = <2>; + vfront-porch = <2>; + vsync-len = <2>; + hsync-active = <1>; + }; + }; + +Every required property also supports the use of ranges, so the commonly used +datasheet description with minimum, typical and maximum values can be used. + +Example: + + timing1: timing { + /* 1920x1080p24 */ + clock-frequency = <148500000>; + hactive = <1920>; + vactive = <1080>; + hsync-len = <0 44 60>; + hfront-porch = <80 88 95>; + hback-porch = <100 148 160>; + vfront-porch = <0 4 6>; + vback-porch = <0 36 50>; + vsync-len = <0 5 6>; + }; diff --git a/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt b/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt new file mode 100644 index 00000000000..ecf42c07684 --- /dev/null +++ b/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt @@ -0,0 +1,19 @@ +* Freescale i.MX One wire bus master controller + +Required properties: +- compatible : should be "fsl,imx21-owire" +- reg : Address and length of the register set for the device + +Optional properties: +- clocks : phandle of clock that supplies the module (required if platform + clock bindings use device tree) + +Example: + +- From imx53.dtsi: +owire: owire@63fa4000 { + compatible = "fsl,imx53-owire", "fsl,imx21-owire"; + reg = <0x63fa4000 0x4000>; + clocks = <&clks 159>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index d4d66757354..b2fb2f5e192 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -1228,7 +1228,7 @@ hierarchy and routing of interrupts in the hardware. The interrupt tree model is fully described in the document "Open Firmware Recommended Practice: Interrupt Mapping Version 0.9". The document is available at: -<http://playground.sun.com/1275/practice>. +<http://www.openfirmware.org/ofwg/practice/> 1) interrupts property ---------------------- |