diff options
Diffstat (limited to 'Documentation/devicetree')
131 files changed, 3459 insertions, 171 deletions
diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt index 926b4d6aae7..26799ef562d 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt @@ -1,20 +1,21 @@ Power Management Service Unit(PMSU) ----------------------------------- -Available on Marvell SOCs: Armada 370 and Armada XP +Available on Marvell SOCs: Armada 370, Armada 38x and Armada XP Required properties: -- compatible: "marvell,armada-370-xp-pmsu" +- compatible: should be one of: + - "marvell,armada-370-pmsu" for Armada 370 or Armada XP + - "marvell,armada-380-pmsu" for Armada 38x + - "marvell,armada-370-xp-pmsu" was used for Armada 370/XP but is now + deprecated and will be removed -- reg: Should contain PMSU registers location and length. First pair - for the per-CPU SW Reset Control registers, second pair for the - Power Management Service Unit. +- reg: Should contain PMSU registers location and length. Example: -armada-370-xp-pmsu@d0022000 { - compatible = "marvell,armada-370-xp-pmsu"; - reg = <0xd0022100 0x430>, - <0xd0020800 0x20>; +armada-370-xp-pmsu@22000 { + compatible = "marvell,armada-370-pmsu"; + reg = <0x22000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt b/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt new file mode 100644 index 00000000000..b63a7b6ab99 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-cpu-reset.txt @@ -0,0 +1,14 @@ +Marvell Armada CPU reset controller +=================================== + +Required properties: + +- compatible: Should be "marvell,armada-370-cpu-reset". + +- reg: should be register base and length as documented in the + datasheet for the CPU reset registers + +cpurst: cpurst@20800 { + compatible = "marvell,armada-370-cpu-reset"; + reg = <0x20800 0x20>; +}; diff --git a/Documentation/devicetree/bindings/arm/axxia.txt b/Documentation/devicetree/bindings/arm/axxia.txt new file mode 100644 index 00000000000..7b4ef9c0769 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/axxia.txt @@ -0,0 +1,12 @@ +Axxia AXM55xx device tree bindings + +Boards using the AXM55xx SoC need to have the following properties: + +Required root node property: + + - compatible = "lsi,axm5516" + +Boards: + + LSI AXM5516 Validation board (Amarillo) + compatible = "lsi,axm5516-amarillo", "lsi,axm5516" diff --git a/Documentation/devicetree/bindings/arm/coherency-fabric.txt b/Documentation/devicetree/bindings/arm/coherency-fabric.txt index 17d8cd10755..8dd46617c88 100644 --- a/Documentation/devicetree/bindings/arm/coherency-fabric.txt +++ b/Documentation/devicetree/bindings/arm/coherency-fabric.txt @@ -1,16 +1,33 @@ Coherency fabric ---------------- -Available on Marvell SOCs: Armada 370 and Armada XP +Available on Marvell SOCs: Armada 370, Armada 375, Armada 38x and Armada XP Required properties: -- compatible: "marvell,coherency-fabric" +- compatible: the possible values are: + + * "marvell,coherency-fabric", to be used for the coherency fabric of + the Armada 370 and Armada XP. + + * "marvell,armada-375-coherency-fabric", for the Armada 375 coherency + fabric. + + * "marvell,armada-380-coherency-fabric", for the Armada 38x coherency + fabric. - reg: Should contain coherency fabric registers location and - length. First pair for the coherency fabric registers, second pair - for the per-CPU fabric registers registers. + length. + + * For "marvell,coherency-fabric", the first pair for the coherency + fabric registers, second pair for the per-CPU fabric registers. -Example: + * For "marvell,armada-375-coherency-fabric", only one pair is needed + for the per-CPU fabric registers. + + * For "marvell,armada-380-coherency-fabric", only one pair is needed + for the per-CPU fabric registers. + +Examples: coherency-fabric@d0020200 { compatible = "marvell,coherency-fabric"; @@ -19,3 +36,8 @@ coherency-fabric@d0020200 { }; +coherency-fabric@21810 { + compatible = "marvell,armada-375-coherency-fabric"; + reg = <0x21810 0x1c>; +}; + diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 333f4aea302..1fe72a0778c 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -178,13 +178,19 @@ nodes to be present and contain the properties described below. Usage and definition depend on ARM architecture version. # On ARM v8 64-bit this property is required and must be one of: - "spin-table" "psci" + "spin-table" # On ARM 32-bit systems this property is optional and can be one of: + "allwinner,sun6i-a31" + "arm,psci" + "marvell,armada-375-smp" + "marvell,armada-380-smp" + "marvell,armada-xp-smp" "qcom,gcc-msm8660" "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" + "rockchip,rk3066-smp" - cpu-release-addr Usage: required for systems that have an "enable-method" diff --git a/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt b/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt new file mode 100644 index 00000000000..4a0a4f70a0c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt @@ -0,0 +1,38 @@ +Samsung Exynos SYSRAM for SMP bringup: +------------------------------------ + +Samsung SMP-capable Exynos SoCs use part of the SYSRAM for the bringup +of the secondary cores. Once the core gets powered up it executes the +code that is residing at some specific location of the SYSRAM. + +Therefore reserved section sub-nodes have to be added to the mmio-sram +declaration. These nodes are of two types depending upon secure or +non-secure execution environment. + +Required sub-node properties: +- compatible : depending upon boot mode, should be + "samsung,exynos4210-sysram" : for Secure SYSRAM + "samsung,exynos4210-sysram-ns" : for Non-secure SYSRAM + +The rest of the properties should follow the generic mmio-sram discription +found in ../../misc/sysram.txt + +Example: + + sysram@02020000 { + compatible = "mmio-sram"; + reg = <0x02020000 0x54000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x02020000 0x54000>; + + smp-sysram@0 { + compatible = "samsung,exynos4210-sysram"; + reg = <0x0 0x1000>; + }; + + smp-sysram@53000 { + compatible = "samsung,exynos4210-sysram-ns"; + reg = <0x53000 0x1000>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/global_timer.txt b/Documentation/devicetree/bindings/arm/global_timer.txt index 1e548981eda..bdae3a81879 100644 --- a/Documentation/devicetree/bindings/arm/global_timer.txt +++ b/Documentation/devicetree/bindings/arm/global_timer.txt @@ -4,8 +4,11 @@ ** Timer node required properties: -- compatible : Should be "arm,cortex-a9-global-timer" - Driver supports versions r2p0 and above. +- compatible : should contain + * "arm,cortex-a5-global-timer" for Cortex-A5 global timers. + * "arm,cortex-a9-global-timer" for Cortex-A9 global + timers or any compatible implementation. Note: driver + supports versions r2p0 and above. - interrupts : One interrupt to each core diff --git a/Documentation/devicetree/bindings/arm/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/marvell,berlin.txt index 737afa5f814..94013a9a876 100644 --- a/Documentation/devicetree/bindings/arm/marvell,berlin.txt +++ b/Documentation/devicetree/bindings/arm/marvell,berlin.txt @@ -12,6 +12,7 @@ SoC and board used. Currently known SoC compatibles are: "marvell,berlin2" for Marvell Armada 1500 (BG2, 88DE3100), "marvell,berlin2cd" for Marvell Armada 1500-mini (BG2CD, 88DE3005) "marvell,berlin2ct" for Marvell Armada ? (BG2CT, 88DE????) + "marvell,berlin2q" for Marvell Armada 1500-pro (BG2Q, 88DE3114) "marvell,berlin3" for Marvell Armada ? (BG3, 88DE????) * Example: @@ -22,3 +23,104 @@ SoC and board used. Currently known SoC compatibles are: ... } + +* Marvell Berlin2 chip control binding + +Marvell Berlin SoCs have a chip control register set providing several +individual registers dealing with pinmux, padmux, clock, reset, and secondary +CPU boot address. Unfortunately, the individual registers are spread among the +chip control registers, so there should be a single DT node only providing the +different functions which are described below. + +Required properties: +- compatible: shall be one of + "marvell,berlin2-chip-ctrl" for BG2 + "marvell,berlin2cd-chip-ctrl" for BG2CD + "marvell,berlin2q-chip-ctrl" for BG2Q +- reg: address and length of following register sets for + BG2/BG2CD: chip control register set + BG2Q: chip control register set and cpu pll registers + +* Marvell Berlin2 system control binding + +Marvell Berlin SoCs have a system control register set providing several +individual registers dealing with pinmux, padmux, and reset. + +Required properties: +- compatible: should be one of + "marvell,berlin2-system-ctrl" for BG2 + "marvell,berlin2cd-system-ctrl" for BG2CD + "marvell,berlin2q-system-ctrl" for BG2Q +- reg: address and length of the system control register set + +* Clock provider binding + +As clock related registers are spread among the chip control registers, the +chip control node also provides the clocks. Marvell Berlin2 (BG2, BG2CD, BG2Q) +SoCs share the same IP for PLLs and clocks, with some minor differences in +features and register layout. + +Required properties: +- #clock-cells: shall be set to 1 +- clocks: clock specifiers referencing the core clock input clocks +- clock-names: array of strings describing the input clock specifiers above. + Allowed clock-names for the reference clocks are + "refclk" for the SoCs osciallator input on all SoCs, + and SoC-specific input clocks for + BG2/BG2CD: "video_ext0" for the external video clock input + +Clocks provided by core clocks shall be referenced by a clock specifier +indexing one of the provided clocks. Refer to dt-bindings/clock/berlin<soc>.h +for the corresponding index mapping. + +* Pin controller binding + +Pin control registers are part of both register sets, chip control and system +control. The pins controlled are organized in groups, so no actual pin +information is needed. + +A pin-controller node should contain subnodes representing the pin group +configurations, one per function. Each subnode has the group name and the muxing +function used. + +Be aware the Marvell Berlin datasheets use the keyword 'mode' for what is called +a 'function' in the pin-controller subsystem. + +Required subnode-properties: +- groups: a list of strings describing the group names. +- function: a string describing the function used to mux the groups. + +Example: + +chip: chip-control@ea0000 { + compatible = "marvell,berlin2-chip-ctrl"; + #clock-cells = <1>; + reg = <0xea0000 0x400>; + clocks = <&refclk>, <&externaldev 0>; + clock-names = "refclk", "video_ext0"; + + spi1_pmux: spi1-pmux { + groups = "G0"; + function = "spi1"; + }; +}; + +sysctrl: system-controller@d000 { + compatible = "marvell,berlin2-system-ctrl"; + reg = <0xd000 0x100>; + + uart0_pmux: uart0-pmux { + groups = "GSM4"; + function = "uart0"; + }; + + uart1_pmux: uart1-pmux { + groups = "GSM5"; + function = "uart1"; + }; + + uart2_pmux: uart2-pmux { + groups = "GSM3"; + function = "uart2"; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt index c0105de55cb..974624ea68f 100644 --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -6,6 +6,8 @@ provided by Arteris. Required properties: - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family Should be "ti,omap4-l3-noc" for OMAP4 family + Should be "ti,dra7-l3-noc" for DRA7 family + Should be "ti,am4372-l3-noc" for AM43 family - reg: Contains L3 register address range for each noc domain. - ti,hwmods: "l3_main_1", ... One hwmod for each noc domain. diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 36ede19a163..d22b216f5d2 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -80,7 +80,10 @@ SoCs: compatible = "ti,omap5432", "ti,omap5" - DRA742 - compatible = "ti,dra7xx", "ti,dra7" + compatible = "ti,dra742", "ti,dra74", "ti,dra7" + +- DRA722 + compatible = "ti,dra722", "ti,dra72", "ti,dra7" - AM4372 compatible = "ti,am4372", "ti,am43" @@ -102,6 +105,12 @@ Boards: - OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4"; +- OMAP4 VAR-STK-OM44 : Commercial dev kit with VAR-OM44CustomBoard and VAR-SOM-OM44 w/WLAN + compatible = "variscite,var-stk-om44", "variscite,var-som-om44", "ti,omap4460", "ti,omap4"; + +- OMAP4 VAR-DVK-OM44 : Commercial dev kit with VAR-OM44CustomBoard, VAR-SOM-OM44 w/WLAN and LCD touchscreen + compatible = "variscite,var-dvk-om44", "variscite,var-som-om44", "ti,omap4460", "ti,omap4"; + - OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x compatible = "ti,omap3-evm", "ti,omap3" @@ -120,5 +129,8 @@ Boards: - AM437x GP EVM compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43" -- DRA7 EVM: Software Developement Board for DRA7XX - compatible = "ti,dra7-evm", "ti,dra7" +- DRA742 EVM: Software Development Board for DRA742 + compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" + +- DRA722 EVM: Software Development Board for DRA722 + compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index fe5cef8976c..75ef91d08f3 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -8,6 +8,7 @@ Required properties: - compatible : should be one of "arm,armv8-pmuv3" + "arm,cortex-a17-pmu" "arm,cortex-a15-pmu" "arm,cortex-a12-pmu" "arm,cortex-a9-pmu" diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt index 433afe9cb59..b4a58f39223 100644 --- a/Documentation/devicetree/bindings/arm/psci.txt +++ b/Documentation/devicetree/bindings/arm/psci.txt @@ -21,7 +21,15 @@ to #0. Main node required properties: - - compatible : Must be "arm,psci" + - compatible : should contain at least one of: + + * "arm,psci" : for implementations complying to PSCI versions prior to + 0.2. For these cases function IDs must be provided. + + * "arm,psci-0.2" : for implementations complying to PSCI 0.2. Function + IDs are not required and should be ignored by an OS with PSCI 0.2 + support, but are permitted to be present for compatibility with + existing software when "arm,psci" is later in the compatible list. - method : The method of calling the PSCI firmware. Permitted values are: @@ -45,6 +53,8 @@ Main node optional properties: Example: +Case 1: PSCI v0.1 only. + psci { compatible = "arm,psci"; method = "smc"; @@ -53,3 +63,28 @@ Example: cpu_on = <0x95c10002>; migrate = <0x95c10003>; }; + + +Case 2: PSCI v0.2 only + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + +Case 3: PSCI v0.2 and PSCI v0.1. + + A DTB may provide IDs for use by kernels without PSCI 0.2 support, + enabling firmware and hypervisors to support existing and new kernels. + These IDs will be ignored by kernels with PSCI 0.2 support, which will + use the standard PSCI 0.2 IDs exclusively. + + psci { + compatible = "arm,psci-0.2", "arm,psci"; + method = "hvc"; + + cpu_on = < arbitrary value >; + cpu_off = < arbitrary value >; + + ... + }; diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt new file mode 100644 index 00000000000..857f12636eb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -0,0 +1,10 @@ +Rockchip platforms device tree bindings +--------------------------------------- + +- bq Curie 2 tablet: + Required root node properties: + - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a"; + +- Radxa Rock board: + Required root node properties: + - compatible = "radxa,rock", "rockchip,rk3188"; diff --git a/Documentation/devicetree/bindings/arm/samsung/pmu.txt b/Documentation/devicetree/bindings/arm/samsung/pmu.txt index f1f155255f2..2a4ab046a8a 100644 --- a/Documentation/devicetree/bindings/arm/samsung/pmu.txt +++ b/Documentation/devicetree/bindings/arm/samsung/pmu.txt @@ -2,6 +2,10 @@ SAMSUNG Exynos SoC series PMU Registers Properties: - compatible : should contain two values. First value must be one from following list: + - "samsung,exynos3250-pmu" - for Exynos3250 SoC, + - "samsung,exynos4210-pmu" - for Exynos4210 SoC, + - "samsung,exynos4212-pmu" - for Exynos4212 SoC, + - "samsung,exynos4412-pmu" - for Exynos4412 SoC, - "samsung,exynos5250-pmu" - for Exynos5250 SoC, - "samsung,exynos5420-pmu" - for Exynos5420 SoC. second value must be always "syscon". diff --git a/Documentation/devicetree/bindings/arm/samsung/sysreg.txt b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt index 0ab3251a6ec..4fced6e9d5e 100644 --- a/Documentation/devicetree/bindings/arm/samsung/sysreg.txt +++ b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt @@ -1,8 +1,10 @@ SAMSUNG S5P/Exynos SoC series System Registers (SYSREG) Properties: - - compatible : should contain "samsung,<chip name>-sysreg", "syscon"; - For Exynos4 SoC series it should be "samsung,exynos4-sysreg", "syscon"; + - compatible : should contain two values. First value must be one from following list: + - "samsung,exynos4-sysreg" - for Exynos4 based SoCs, + - "samsung,exynos5-sysreg" - for Exynos5 based SoCs. + second value must be always "syscon". - reg : offset and length of the register set. Example: @@ -10,3 +12,8 @@ Example: compatible = "samsung,exynos4-sysreg", "syscon"; reg = <0x10010000 0x400>; }; + + syscon@10050000 { + compatible = "samsung,exynos5-sysreg", "syscon"; + reg = <0x10050000 0x5000>; + }; diff --git a/Documentation/devicetree/bindings/arm/sti.txt b/Documentation/devicetree/bindings/arm/sti.txt new file mode 100644 index 00000000000..92f16c78bb6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sti.txt @@ -0,0 +1,15 @@ +ST STi Platforms Device Tree Bindings +--------------------------------------- + +Boards with the ST STiH415 SoC shall have the following properties: +Required root node property: +compatible = "st,stih415"; + +Boards with the ST STiH416 SoC shall have the following properties: +Required root node property: +compatible = "st,stih416"; + +Boards with the ST STiH407 SoC shall have the following properties: +Required root node property: +compatible = "st,stih407"; + diff --git a/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt index 5580e9c4bd8..00318d083c9 100644 --- a/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt +++ b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt @@ -8,6 +8,8 @@ interrupt generation, MMC and NOR Flash control etc. Required node properties: - compatible value : = "arm,vexpress,sysreg"; - reg : physical base address and the size of the registers window + +Deprecated properties, replaced by GPIO subnodes (see below): - gpio-controller : specifies that the node is a GPIO controller - #gpio-cells : size of the GPIO specifier, should be 2: - first cell is the pseudo-GPIO line number: @@ -16,35 +18,86 @@ Required node properties: 2 - NOR FLASH WPn - second cell can take standard GPIO flags (currently ignored). +Control registers providing pseudo-GPIO lines must be represented +by subnodes, each of them requiring the following properties: +- compatible value : one of + "arm,vexpress-sysreg,sys_led" + "arm,vexpress-sysreg,sys_mci" + "arm,vexpress-sysreg,sys_flash" +- gpio-controller : makes the node a GPIO controller +- #gpio-cells : size of the GPIO specifier, must be 2: + - first cell is the function number: + - for sys_led : 0..7 = LED 0..7 + - for sys_mci : 0 = MMC CARDIN, 1 = MMC WPROT + - for sys_flash : 0 = NOR FLASH WPn + - second cell can take standard GPIO flags (currently ignored). + Example: v2m_sysreg: sysreg@10000000 { compatible = "arm,vexpress-sysreg"; reg = <0x10000000 0x1000>; - gpio-controller; - #gpio-cells = <2>; + + v2m_led_gpios: sys_led@08 { + compatible = "arm,vexpress-sysreg,sys_led"; + gpio-controller; + #gpio-cells = <2>; + }; + + v2m_mmc_gpios: sys_mci@48 { + compatible = "arm,vexpress-sysreg,sys_mci"; + gpio-controller; + #gpio-cells = <2>; + }; + + v2m_flash_gpios: sys_flash@4c { + compatible = "arm,vexpress-sysreg,sys_flash"; + gpio-controller; + #gpio-cells = <2>; + }; }; This block also can also act a bridge to the platform's configuration bus via "system control" interface, addressing devices with site number, position in the board stack, config controller, function and device -numbers - see motherboard's TRM for more details. - -The node describing a config device must refer to the sysreg node via -"arm,vexpress,config-bridge" phandle (can be also defined in the node's -parent) and relies on the board topology properties - see main vexpress -node documentation for more details. It must also define the following -property: -- arm,vexpress-sysreg,func : must contain two cells: - - first cell defines function number (eg. 1 for clock generator, - 2 for voltage regulators etc.) - - device number (eg. osc 0, osc 1 etc.) +numbers - see motherboard's TRM for more details. All configuration +controller accessible via this interface must reference the sysreg +node via "arm,vexpress,config-bridge" phandle and define appropriate +topology properties - see main vexpress node documentation for more +details. Each child of such node describes one function and must +define the following properties: +- compatible value : must be one of (corresponding to the TRM): + "arm,vexpress-amp" + "arm,vexpress-dvimode" + "arm,vexpress-energy" + "arm,vexpress-muxfpga" + "arm,vexpress-osc" + "arm,vexpress-power" + "arm,vexpress-reboot" + "arm,vexpress-reset" + "arm,vexpress-scc" + "arm,vexpress-shutdown" + "arm,vexpress-temp" + "arm,vexpress-volt" +- arm,vexpress-sysreg,func : must contain a set of two cells long groups: + - first cell of each group defines the function number + (eg. 1 for clock generator, 2 for voltage regulators etc.) + - second cell of each group defines device number (eg. osc 0, + osc 1 etc.) + - some functions (eg. energy meter, with its 64 bit long counter) + are using more than one function/device number pair Example: mcc { + compatible = "arm,vexpress,config-bus"; arm,vexpress,config-bridge = <&v2m_sysreg>; osc@0 { compatible = "arm,vexpress-osc"; arm,vexpress-sysreg,func = <1 0>; }; + + energy@0 { + compatible = "arm,vexpress-energy"; + arm,vexpress-sysreg,func = <13 0>, <13 1>; + }; }; diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt index ae49161e478..39844cd0bcc 100644 --- a/Documentation/devicetree/bindings/arm/vexpress.txt +++ b/Documentation/devicetree/bindings/arm/vexpress.txt @@ -80,12 +80,17 @@ but also control clock generators, voltage regulators, gather environmental data like temperature, power consumption etc. Even the video output switch (FPGA) is controlled that way. -Nodes describing devices controlled by this infrastructure should -point at the bridge device node: +The controllers are not mapped into normal memory address space +and must be accessed through bridges - other devices capable +of generating transactions on the configuration bus. + +The nodes describing configuration controllers must define +the following properties: +- compatible value: + compatible = "arm,vexpress,config-bus"; - bridge phandle: arm,vexpress,config-bridge = <phandle>; -This property can be also defined in a parent node (eg. for a DCC) -and is effective for all children. +and children describing available functions. Platform topology @@ -197,7 +202,7 @@ Example of a VE tile description (simplified) }; dcc { - compatible = "simple-bus"; + compatible = "arm,vexpress,config-bus"; arm,vexpress,config-bridge = <&v2m_sysreg>; osc@0 { diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt new file mode 100644 index 00000000000..e2d501d20c9 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt @@ -0,0 +1,30 @@ +Broadcom GISB bus Arbiter controller + +Required properties: + +- compatible: should be "brcm,gisb-arb" +- reg: specifies the base physical address and size of the registers +- interrupt-parent: specifies the phandle to the parent interrupt controller + this arbiter gets interrupt line from +- interrupts: specifies the two interrupts (timeout and TEA) to be used from + the parent interrupt controller + +Optional properties: + +- brcm,gisb-arb-master-mask: 32-bits wide bitmask used to specify which GISB + masters are valid at the system level +- brcm,gisb-arb-master-names: string list of the litteral name of the GISB + masters. Should match the number of bits set in brcm,gisb-master-mask and + the order in which they appear + +Example: + +gisb-arb@f0400000 { + compatible = "brcm,gisb-arb"; + reg = <0xf0400000 0x800>; + interrupts = <0>, <2>; + interrupt-parent = <&sun_l2_intc>; + + brcm,gisb-arb-master-mask = <0x7>; + brcm,gisb-arb-master-names = "bsp_0", "scpu_0", "cpu_0"; +}; diff --git a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt index 7586fb68c07..5fa44f52a0b 100644 --- a/Documentation/devicetree/bindings/bus/mvebu-mbus.txt +++ b/Documentation/devicetree/bindings/bus/mvebu-mbus.txt @@ -197,7 +197,7 @@ to be set by the operating system and that are guaranteed to be free of overlaps with one another or with the system memory ranges. Each entry in the property refers to exactly one window. If the operating system -choses to use a different set of mbus windows, it must ensure that any address +chooses to use a different set of mbus windows, it must ensure that any address translations performed from downstream devices are adapted accordingly. The operating system may insert additional mbus windows that do not conflict diff --git a/Documentation/devicetree/bindings/clock/altr_socfpga.txt b/Documentation/devicetree/bindings/clock/altr_socfpga.txt index 5dfd145d3cc..f72e80e0dad 100644 --- a/Documentation/devicetree/bindings/clock/altr_socfpga.txt +++ b/Documentation/devicetree/bindings/clock/altr_socfpga.txt @@ -21,8 +21,8 @@ Optional properties: - fixed-divider : If clocks have a fixed divider value, use this property. - clk-gate : For "socfpga-gate-clk", clk-gate contains the gating register and the bit index. -- div-reg : For "socfpga-gate-clk", div-reg contains the divider register, bit shift, - and width. +- div-reg : For "socfpga-gate-clk" and "socfpga-periph-clock", div-reg contains + the divider register, bit shift, and width. - clk-phase : For the sdmmc_clk, contains the value of the clock phase that controls the SDMMC CIU clock. The first value is the clk_sample(smpsel), and the second value is the cclk_in_drv(drvsel). The clk-phase is used to enable the correct diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index 6794cdc96d8..b3d544ca522 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -6,6 +6,16 @@ This binding uses the common clock binding[1]. Required properties: - compatible : shall be one of the following: + "atmel,at91sam9x5-sckc": + at91 SCKC (Slow Clock Controller) + This node contains the slow clock definitions. + + "atmel,at91sam9x5-clk-slow-osc": + at91 slow oscillator + + "atmel,at91sam9x5-clk-slow-rc-osc": + at91 internal slow RC oscillator + "atmel,at91rm9200-pmc" or "atmel,at91sam9g45-pmc" or "atmel,at91sam9n12-pmc" or @@ -15,8 +25,18 @@ Required properties: All at91 specific clocks (clocks defined below) must be child node of the PMC node. + "atmel,at91sam9x5-clk-slow" (under sckc node) + or + "atmel,at91sam9260-clk-slow" (under pmc node): + at91 slow clk + + "atmel,at91rm9200-clk-main-osc" + "atmel,at91sam9x5-clk-main-rc-osc" + at91 main clk sources + + "atmel,at91sam9x5-clk-main" "atmel,at91rm9200-clk-main": - at91 main oscillator + at91 main clock "atmel,at91rm9200-clk-master" or "atmel,at91sam9x5-clk-master": @@ -54,6 +74,63 @@ Required properties: "atmel,at91sam9x5-clk-utmi": at91 utmi clock +Required properties for SCKC node: +- reg : defines the IO memory reserved for the SCKC. +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). + + +For example: + sckc: sckc@fffffe50 { + compatible = "atmel,sama5d3-pmc"; + reg = <0xfffffe50 0x4> + #size-cells = <0>; + #address-cells = <1>; + + /* put at91 slow clocks here */ + }; + + +Required properties for internal slow RC oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + slow_rc_osc: slow_rc_osc { + compatible = "atmel,at91sam9x5-clk-slow-rc-osc"; + clock-frequency = <32768>; + clock-accuracy = <50000000>; + }; + +Required properties for slow oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Set this when a clock signal is directly + provided on XIN. + +For example: + slow_osc: slow_osc { + compatible = "atmel,at91rm9200-clk-slow-osc"; + #clock-cells = <0>; + clocks = <&slow_xtal>; + }; + +Required properties for slow clock: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the slow clk sources (see atmel datasheet). + +For example: + clk32k: slck { + compatible = "atmel,at91sam9x5-clk-slow"; + #clock-cells = <0>; + clocks = <&slow_rc_osc &slow_osc>; + }; + Required properties for PMC node: - reg : defines the IO memory reserved for the PMC. - #size-cells : shall be 0 (reg is used to encode clk id). @@ -85,24 +162,57 @@ For example: /* put at91 clocks here */ }; +Required properties for main clock internal RC oscillator: +- interrupt-parent : must reference the PMC node. +- interrupts : shall be set to "<0>". +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + main_rc_osc: main_rc_osc { + compatible = "atmel,at91sam9x5-clk-main-rc-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + clock-frequency = <12000000>; + clock-accuracy = <50000000>; + }; + +Required properties for main clock oscillator: +- interrupt-parent : must reference the PMC node. +- interrupts : shall be set to "<0>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Specified if a clock signal is provided + on XIN. + + clock signal is directly provided on XIN pin. + +For example: + main_osc: main_osc { + compatible = "atmel,at91rm9200-clk-main-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + #clock-cells = <0>; + clocks = <&main_xtal>; + }; + Required properties for main clock: - interrupt-parent : must reference the PMC node. - interrupts : shall be set to "<0>". - #clock-cells : from common clock binding; shall be set to 0. -- clocks (optional if clock-frequency is provided) : shall be the slow clock - phandle. This clock is used to calculate the main clock rate if - "clock-frequency" is not provided. -- clock-frequency : the main oscillator frequency.Prefer the use of - "clock-frequency" over automatic clock rate calculation. +- clocks : shall encode the main clk sources (see atmel datasheet). For example: main: mainck { - compatible = "atmel,at91rm9200-clk-main"; + compatible = "atmel,at91sam9x5-clk-main"; interrupt-parent = <&pmc>; interrupts = <0>; #clock-cells = <0>; - clocks = <&ck32k>; - clock-frequency = <18432000>; + clocks = <&main_rc_osc &main_osc>; }; Required properties for master clock: diff --git a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt new file mode 100644 index 00000000000..aadc9c59e2d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt @@ -0,0 +1,41 @@ +* Samsung Exynos3250 Clock Controller + +The Exynos3250 clock controller generates and supplies clock to various +controllers within the Exynos3250 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos3250-cmu" - controller compatible with Exynos3250 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos3250.h header and can be used in device +tree sources. + +Example 1: An example of a clock controller node is listed below. + + cmu: clock-controller@10030000 { + compatible = "samsung,exynos3250-cmu"; + reg = <0x10030000 0x20000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@13800000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x13800000 0x100>; + interrupts = <0 109 0>; + clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos5260-clock.txt b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt new file mode 100644 index 00000000000..5496b2fac48 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt @@ -0,0 +1,190 @@ +* Samsung Exynos5260 Clock Controller + +Exynos5260 has 13 clock controllers which are instantiated +independently from the device-tree. These clock controllers +generate and supply clocks to various hardware blocks within +the SoC. + +Each clock is assigned an identifier and client nodes can use +this identifier to specify the clock which they consume. All +available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5260-clk.h header and can be used in +device tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It +is expected that they are defined using standard clock bindings +with following clock-output-names: + + - "fin_pll" - PLL input clock from XXTI + - "xrtcxti" - input clock from XRTCXTI + - "ioclk_pcm_extclk" - pcm external operation clock + - "ioclk_spdif_extclk" - spdif external operation clock + - "ioclk_i2s_cdclk" - i2s0 codec clock + +Phy clocks: + +There are several clocks which are generated by specific PHYs. +These clocks are fed into the clock controller and then routed to +the hardware blocks. These clocks are defined as fixed clocks in the +driver with following names: + + - "phyclk_dptx_phy_ch3_txd_clk" - dp phy clock for channel 3 + - "phyclk_dptx_phy_ch2_txd_clk" - dp phy clock for channel 2 + - "phyclk_dptx_phy_ch1_txd_clk" - dp phy clock for channel 1 + - "phyclk_dptx_phy_ch0_txd_clk" - dp phy clock for channel 0 + - "phyclk_hdmi_phy_tmds_clko" - hdmi phy tmds clock + - "phyclk_hdmi_phy_pixel_clko" - hdmi phy pixel clock + - "phyclk_hdmi_link_o_tmds_clkhi" - hdmi phy for hdmi link + - "phyclk_dptx_phy_o_ref_clk_24m" - dp phy reference clock + - "phyclk_dptx_phy_clk_div2" + - "phyclk_mipi_dphy_4l_m_rxclkesc0" + - "phyclk_usbhost20_phy_phyclock" - usb 2.0 phy clock + - "phyclk_usbhost20_phy_freeclk" + - "phyclk_usbhost20_phy_clk48mohci" + - "phyclk_usbdrd30_udrd30_pipe_pclk" + - "phyclk_usbdrd30_udrd30_phyclock" - usb 3.0 phy clock + +Required Properties for Clock Controller: + + - compatible: should be one of the following. + 1) "samsung,exynos5260-clock-top" + 2) "samsung,exynos5260-clock-peri" + 3) "samsung,exynos5260-clock-egl" + 4) "samsung,exynos5260-clock-kfc" + 5) "samsung,exynos5260-clock-g2d" + 6) "samsung,exynos5260-clock-mif" + 7) "samsung,exynos5260-clock-mfc" + 8) "samsung,exynos5260-clock-g3d" + 9) "samsung,exynos5260-clock-fsys" + 10) "samsung,exynos5260-clock-aud" + 11) "samsung,exynos5260-clock-isp" + 12) "samsung,exynos5260-clock-gscl" + 13) "samsung,exynos5260-clock-disp" + + - reg: physical base address of the controller and the length of + memory mapped region. + + - #clock-cells: should be 1. + + - clocks: list of clock identifiers which are fed as the input to + the given clock controller. Please refer the next section to find + the input clocks for a given controller. + + - clock-names: list of names of clocks which are fed as the input + to the given clock controller. + +Input clocks for top clock controller: + - fin_pll + - dout_mem_pll + - dout_bus_pll + - dout_media_pll + +Input clocks for peri clock controller: + - fin_pll + - ioclk_pcm_extclk + - ioclk_i2s_cdclk + - ioclk_spdif_extclk + - phyclk_hdmi_phy_ref_cko + - dout_aclk_peri_66 + - dout_sclk_peri_uart0 + - dout_sclk_peri_uart1 + - dout_sclk_peri_uart2 + - dout_sclk_peri_spi0_b + - dout_sclk_peri_spi1_b + - dout_sclk_peri_spi2_b + - dout_aclk_peri_aud + - dout_sclk_peri_spi0_b + +Input clocks for egl clock controller: + - fin_pll + - dout_bus_pll + +Input clocks for kfc clock controller: + - fin_pll + - dout_media_pll + +Input clocks for g2d clock controller: + - fin_pll + - dout_aclk_g2d_333 + +Input clocks for mif clock controller: + - fin_pll + +Input clocks for mfc clock controller: + - fin_pll + - dout_aclk_mfc_333 + +Input clocks for g3d clock controller: + - fin_pll + +Input clocks for fsys clock controller: + - fin_pll + - phyclk_usbhost20_phy_phyclock + - phyclk_usbhost20_phy_freeclk + - phyclk_usbhost20_phy_clk48mohci + - phyclk_usbdrd30_udrd30_pipe_pclk + - phyclk_usbdrd30_udrd30_phyclock + - dout_aclk_fsys_200 + +Input clocks for aud clock controller: + - fin_pll + - fout_aud_pll + - ioclk_i2s_cdclk + - ioclk_pcm_extclk + +Input clocks for isp clock controller: + - fin_pll + - dout_aclk_isp1_266 + - dout_aclk_isp1_400 + - mout_aclk_isp1_266 + +Input clocks for gscl clock controller: + - fin_pll + - dout_aclk_gscl_400 + - dout_aclk_gscl_333 + +Input clocks for disp clock controller: + - fin_pll + - phyclk_dptx_phy_ch3_txd_clk + - phyclk_dptx_phy_ch2_txd_clk + - phyclk_dptx_phy_ch1_txd_clk + - phyclk_dptx_phy_ch0_txd_clk + - phyclk_hdmi_phy_tmds_clko + - phyclk_hdmi_phy_ref_clko + - phyclk_hdmi_phy_pixel_clko + - phyclk_hdmi_link_o_tmds_clkhi + - phyclk_mipi_dphy_4l_m_txbyte_clkhs + - phyclk_dptx_phy_o_ref_clk_24m + - phyclk_dptx_phy_clk_div2 + - phyclk_mipi_dphy_4l_m_rxclkesc0 + - phyclk_hdmi_phy_ref_cko + - ioclk_spdif_extclk + - dout_aclk_peri_aud + - dout_aclk_disp_222 + - dout_sclk_disp_pixel + - dout_aclk_disp_333 + +Example 1: An example of a clock controller node is listed below. + + clock_mfc: clock-controller@11090000 { + compatible = "samsung,exynos5260-clock-mfc"; + clock = <&fin_pll>, <&clock_top TOP_DOUT_ACLK_MFC_333>; + clock-names = "fin_pll", "dout_aclk_mfc_333"; + reg = <0x11090000 0x10000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the + peri clock controller. Refer to the standard clock bindings for + information about 'clocks' and 'clock-names' property. + + serial@12C00000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 146 0>; + clocks = <&clock_peri PERI_PCLK_UART0>, <&clock_peri PERI_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; + diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt new file mode 100644 index 00000000000..aeab635b07b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt @@ -0,0 +1,45 @@ +* Samsung Exynos5410 Clock Controller + +The Exynos5410 clock controller generates and supplies clock to various +controllers within the Exynos5410 SoC. + +Required Properties: + +- compatible: should be "samsung,exynos5410-clock" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5410.h header and can be used in device +tree sources. + +External clock: + +There is clock that is generated outside the SoC. It +is expected that it is defined using standard clock bindings +with following clock-output-name: + + - "fin_pll" - PLL input clock from XXTI + +Example 1: An example of a clock controller node is listed below. + + clock: clock-controller@0x10010000 { + compatible = "samsung,exynos5410-clock"; + reg = <0x10010000 0x30000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@12C20000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 51 0>; + clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt index ca88c97a856..d54f42cf044 100644 --- a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt @@ -1,12 +1,13 @@ * Samsung Exynos5420 Clock Controller The Exynos5420 clock controller generates and supplies clock to various -controllers within the Exynos5420 SoC. +controllers within the Exynos5420 SoC and for the Exynos5800 SoC. Required Properties: - compatible: should be one of the following. - "samsung,exynos5420-clock" - controller compatible with Exynos5420 SoC. + - "samsung,exynos5800-clock" - controller compatible with Exynos5800 SoC. - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt index db4f2f05c4d..ba6b312ff8a 100644 --- a/Documentation/devicetree/bindings/clock/imx25-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt @@ -139,6 +139,9 @@ clocks and IDs. uart5_ipg 124 reserved 125 wdt_ipg 126 + cko_div 127 + cko_sel 128 + cko 129 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx27-clock.txt b/Documentation/devicetree/bindings/clock/imx27-clock.txt index 7a207039373..6bc9fd2c663 100644 --- a/Documentation/devicetree/bindings/clock/imx27-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx27-clock.txt @@ -98,7 +98,12 @@ clocks and IDs. fpm 83 mpll_osc_sel 84 mpll_sel 85 - spll_gate 86 + spll_gate 86 + mshc_div 87 + rtic_ipg_gate 88 + mshc_ipg_gate 89 + rtic_ahb_gate 90 + mshc_baud_gate 91 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index 6aab72bf67e..90ec91fe5ce 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -220,6 +220,7 @@ clocks and IDs. lvds2_sel 205 lvds1_gate 206 lvds2_gate 207 + esai_ahb 208 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx6sx-clock.txt b/Documentation/devicetree/bindings/clock/imx6sx-clock.txt new file mode 100644 index 00000000000..22362b9b7ba --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6sx-clock.txt @@ -0,0 +1,13 @@ +* Clock bindings for Freescale i.MX6 SoloX + +Required properties: +- compatible: Should be "fsl,imx6sx-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6sx-clock.h +for the full list of i.MX6 SoloX clock IDs. diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt index 02a25d99ca6..6c3c0847e4f 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -10,6 +10,7 @@ index in the group, from 0 to 31. Required Properties: - compatible: Must be one of the following + - "renesas,r7s72100-mstp-clocks" for R7S72100 (RZ) MSTP gate clocks - "renesas,r8a7790-mstp-clocks" for R8A7790 (R-Car H2) MSTP gate clocks - "renesas,r8a7791-mstp-clocks" for R8A7791 (R-Car M2) MSTP gate clocks - "renesas,cpg-mstp-clock" for generic MSTP gate clocks diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt new file mode 100644 index 00000000000..822505e715a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt @@ -0,0 +1,50 @@ +* Samsung S3C2410 Clock Controller + +The S3C2410 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to the s3c2410, +s3c2440 and s3c2442 SoCs in the s3c24x family. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c2410-clock" - controller compatible with S3C2410 SoC. + - "samsung,s3c2440-clock" - controller compatible with S3C2440 SoC. + - "samsung,s3c2442-clock" - controller compatible with S3C2442 SoC. +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2410.h header and can be used in device +tree sources. + +External clocks: + +The xti clock used as input for the plls is generated outside the SoC. It is +expected that is are defined using standard clock bindings with a +clock-output-names value of "xti". + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2410-clock"; + reg = <0x4c000000 0x20>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2440-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt new file mode 100644 index 00000000000..2b430960ba4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt @@ -0,0 +1,50 @@ +* Samsung S3C2412 Clock Controller + +The S3C2412 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to the s3c2412 +and s3c2413 SoCs in the s3c24x family. + +Required Properties: + +- compatible: should be "samsung,s3c2412-clock" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2412.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xti" - crystal input - required, + - "ext" - external clock source - optional, + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2412-clock"; + reg = <0x4c000000 0x20>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2412-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2", "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt new file mode 100644 index 00000000000..e67bb05478a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt @@ -0,0 +1,56 @@ +* Samsung S3C2443 Clock Controller + +The S3C2443 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to all SoCs in +the s3c24x family starting with the s3c2443. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c2416-clock" - controller compatible with S3C2416 SoC. + - "samsung,s3c2443-clock" - controller compatible with S3C2443 SoC. + - "samsung,s3c2450-clock" - controller compatible with S3C2450 SoC. +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2443.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xti" - crystal input - required, + - "ext" - external clock source - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_uart" - external uart clock - optional, + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2416-clock"; + reg = <0x4c000000 0x40>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2440-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt new file mode 100644 index 00000000000..3e6a81e9980 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt @@ -0,0 +1,20 @@ +* Device tree bindings for Texas Instruments keystone pll controller + +The main pll controller used to drive theC66x CorePacs, the switch fabric, +and a majority of the peripheral clocks (all but the ARM CorePacs, DDR3 and +the NETCP modules) requires a PLL Controller to manage the various clock +divisions, gating, and synchronization. + +Required properties: + +- compatible: "ti,keystone-pllctrl", "syscon" + +- reg: contains offset/length value for pll controller + registers space. + +Example: + +pllctrl: pll-controller@0x02310000 { + compatible = "ti,keystone-pllctrl", "syscon"; + reg = <0x02310000 0x200>; +}; diff --git a/Documentation/devicetree/bindings/dma/dma.txt b/Documentation/devicetree/bindings/dma/dma.txt index 8f504e6bae1..82104271e75 100644 --- a/Documentation/devicetree/bindings/dma/dma.txt +++ b/Documentation/devicetree/bindings/dma/dma.txt @@ -14,7 +14,7 @@ Required property: Optional properties: - dma-channels: Number of DMA channels supported by the controller. -- dma-requests: Number of DMA requests signals supported by the +- dma-requests: Number of DMA request signals supported by the controller. Example: @@ -44,7 +44,7 @@ Required property: #dma-cells property in the node referenced by phandle containing DMA controller specific information. This typically contains a DMA request line number or a - channel number, but can contain any data that is used + channel number, but can contain any data that is required for configuring a channel. - dma-names: Contains one identifier string for each DMA specifier in the dmas property. The specific strings that can be used diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index ee9be996152..e577196a12c 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -8,7 +8,7 @@ Required properties: "fsl,imx51-sdma" "fsl,imx53-sdma" "fsl,imx6q-sdma" - The -to variants should be preferred since they allow to determnine the + The -to variants should be preferred since they allow to determine the correct ROM script addresses needed for the driver to work without additional firmware. - reg : Should contain SDMA registers location and length diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt index 68ff2137bae..5ba525a1003 100644 --- a/Documentation/devicetree/bindings/dma/ti-edma.txt +++ b/Documentation/devicetree/bindings/dma/ti-edma.txt @@ -2,11 +2,8 @@ TI EDMA Required properties: - compatible : "ti,edma3" -- ti,edma-regions: Number of regions -- ti,edma-slots: Number of slots - #dma-cells: Should be set to <1> Clients should use a single channel number per DMA request. -- dma-channels: Specify total DMA channels per CC - reg: Memory map for accessing module - interrupt-parent: Interrupt controller the interrupt is routed through - interrupts: Exactly 3 interrupts need to be specified in the order: @@ -17,6 +14,13 @@ Optional properties: - ti,hwmods: Name of the hwmods associated to the EDMA - ti,edma-xbar-event-map: Crossbar event to channel map +Deprecated properties: +Listed here in case one wants to boot an old kernel with new DTB. These +properties might need to be added to the new DTS files. +- ti,edma-regions: Number of regions +- ti,edma-slots: Number of slots +- dma-channels: Specify total DMA channels per CC + Example: edma: edma@49000000 { @@ -26,9 +30,6 @@ edma: edma@49000000 { compatible = "ti,edma3"; ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; #dma-cells = <1>; - dma-channels = <64>; - ti,edma-regions = <4>; - ti,edma-slots = <256>; ti,edma-xbar-event-map = /bits/ 16 <1 12 2 13>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt index 3ddc7ccfe5f..c306a2d0f2b 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt @@ -54,7 +54,7 @@ Optional device specific properties: IO 8-15 are bank 2. These chips have two different interrupt outputs: One for bank 1 and another for bank 2. If irq-mirror is set, both interrupts are generated regardless of the bank that an input change - occured on. If it is not set, the interrupt are only generated for the + occurred on. If it is not set, the interrupt are only generated for the bank they belong to. On devices with only one interrupt output this property is useless. diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index f61cef74a21..941a26aa432 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -21,6 +21,12 @@ Required Properties: GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - gpio-ranges: Range of pins managed by the GPIO controller. +Optional properties: + + - clocks: Must contain a reference to the functional clock. The property is + mandatory if the hardware implements a controllable functional clock for + the GPIO instance. + Please refer to gpio.txt in this directory for details of gpio-ranges property and the common GPIO bindings used by client devices. diff --git a/Documentation/devicetree/bindings/hsi/client-devices.txt b/Documentation/devicetree/bindings/hsi/client-devices.txt new file mode 100644 index 00000000000..104c9a3e57a --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/client-devices.txt @@ -0,0 +1,44 @@ +Each HSI port is supposed to have one child node, which +symbols the remote device connected to the HSI port. The +following properties are standardized for HSI clients: + +Required HSI configuration properties: + +- hsi-channel-ids: A list of channel ids + +- hsi-rx-mode: Receiver Bit transmission mode ("stream" or "frame") +- hsi-tx-mode: Transmitter Bit transmission mode ("stream" or "frame") +- hsi-mode: May be used instead hsi-rx-mode and hsi-tx-mode if + the transmission mode is the same for receiver and + transmitter +- hsi-speed-kbps: Max bit transmission speed in kbit/s +- hsi-flow: RX flow type ("synchronized" or "pipeline") +- hsi-arb-mode: Arbitration mode for TX frame ("round-robin", "priority") + +Optional HSI configuration properties: + +- hsi-channel-names: A list with one name per channel specified in the + hsi-channel-ids property + + +Device Tree node example for an HSI client: + +hsi-controller { + hsi-port { + modem: hsi-client { + compatible = "nokia,n900-modem"; + + hsi-channel-ids = <0>, <1>, <2>, <3>; + hsi-channel-names = "mcsaab-control", + "speech-control", + "speech-data", + "mcsaab-data"; + hsi-speed-kbps = <55000>; + hsi-mode = "frame"; + hsi-flow = "synchronized"; + hsi-arb-mode = "round-robin"; + + /* more client specific properties */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/nokia-modem.txt b/Documentation/devicetree/bindings/hsi/nokia-modem.txt new file mode 100644 index 00000000000..8a979780452 --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/nokia-modem.txt @@ -0,0 +1,57 @@ +Nokia modem client bindings + +The Nokia modem HSI client follows the common HSI client binding +and inherits all required properties. The following additional +properties are needed by the Nokia modem HSI client: + +Required properties: +- compatible: Should be one of + "nokia,n900-modem" +- hsi-channel-names: Should contain the following strings + "mcsaab-control" + "speech-control" + "speech-data" + "mcsaab-data" +- gpios: Should provide a GPIO handler for each GPIO listed in + gpio-names +- gpio-names: Should contain the following strings + "cmt_apeslpx" + "cmt_rst_rq" + "cmt_en" + "cmt_rst" + "cmt_bsi" +- interrupts: Should be IRQ handle for modem's reset indication + +Example: + +&ssi_port { + modem: hsi-client { + compatible = "nokia,n900-modem"; + + pinctrl-names = "default"; + pinctrl-0 = <&modem_pins>; + + hsi-channel-ids = <0>, <1>, <2>, <3>; + hsi-channel-names = "mcsaab-control", + "speech-control", + "speech-data", + "mcsaab-data"; + hsi-speed-kbps = <55000>; + hsi-mode = "frame"; + hsi-flow = "synchronized"; + hsi-arb-mode = "round-robin"; + + interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */ + + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */ + <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */ + <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */ + <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */ + <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */ + gpio-names = "cmt_apeslpx", + "cmt_rst_rq", + "cmt_en", + "cmt_rst", + "cmt_bsi"; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/omap-ssi.txt b/Documentation/devicetree/bindings/hsi/omap-ssi.txt new file mode 100644 index 00000000000..f26625e4269 --- /dev/null +++ b/Documentation/devicetree/bindings/hsi/omap-ssi.txt @@ -0,0 +1,97 @@ +OMAP SSI controller bindings + +OMAP Synchronous Serial Interface (SSI) controller implements a legacy +variant of MIPI's High Speed Synchronous Serial Interface (HSI). + +Required properties: +- compatible: Should include "ti,omap3-ssi". +- reg-names: Contains the values "sys" and "gdd" (in this order). +- reg: Contains a matching register specifier for each entry + in reg-names. +- interrupt-names: Contains the value "gdd_mpu". +- interrupts: Contains matching interrupt information for each entry + in interrupt-names. +- ranges: Represents the bus address mapping between the main + controller node and the child nodes below. +- clock-names: Must include the following entries: + "ssi_ssr_fck": The OMAP clock of that name + "ssi_sst_fck": The OMAP clock of that name + "ssi_ick": The OMAP clock of that name +- clocks: Contains a matching clock specifier for each entry in + clock-names. +- #address-cells: Should be set to <1> +- #size-cells: Should be set to <1> + +Each port is represented as a sub-node of the ti,omap3-ssi device. + +Required Port sub-node properties: +- compatible: Should be set to the following value + ti,omap3-ssi-port (applicable to OMAP34xx devices) +- reg-names: Contains the values "tx" and "rx" (in this order). +- reg: Contains a matching register specifier for each entry + in reg-names. +- interrupt-parent Should be a phandle for the interrupt controller +- interrupts: Should contain interrupt specifiers for mpu interrupts + 0 and 1 (in this order). +- ti,ssi-cawake-gpio: Defines which GPIO pin is used to signify CAWAKE + events for the port. This is an optional board-specific + property. If it's missing the port will not be + enabled. + +Example for Nokia N900: + +ssi-controller@48058000 { + compatible = "ti,omap3-ssi"; + + /* needed until hwmod is updated to use the compatible string */ + ti,hwmods = "ssi"; + + reg = <0x48058000 0x1000>, + <0x48059000 0x1000>; + reg-names = "sys", + "gdd"; + + interrupts = <55>; + interrupt-names = "gdd_mpu"; + + clocks = <&ssi_ssr_fck>, + <&ssi_sst_fck>, + <&ssi_ick>; + clock-names = "ssi_ssr_fck", + "ssi_sst_fck", + "ssi_ick"; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ssi-port@4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805a000 0x800>, + <0x4805a800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <67>, + <68>; + + ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */ + } + + ssi-port@4805a000 { + compatible = "ti,omap3-ssi-port"; + + reg = <0x4805b000 0x800>, + <0x4805b800 0x800>; + reg-names = "tx", + "rx"; + + interrupt-parent = <&intc>; + interrupts = <69>, + <70>; + + status = "disabled"; /* second port is not used on N900 */ + } +} diff --git a/Documentation/devicetree/bindings/iio/proximity/as3935.txt b/Documentation/devicetree/bindings/iio/proximity/as3935.txt new file mode 100644 index 00000000000..ae23dd8da73 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/as3935.txt @@ -0,0 +1,28 @@ +Austrian Microsystems AS3935 Franklin lightning sensor device driver + +Required properties: + - compatible: must be "ams,as3935" + - reg: SPI chip select number for the device + - spi-cpha: SPI Mode 1. Refer to spi/spi-bus.txt for generic SPI + slave node bindings. + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic + interrupt client node bindings. + +Optional properties: + - ams,tuning-capacitor-pf: Calibration tuning capacitor stepping + value 0 - 120pF. This will require using the calibration data from + the manufacturer. + +Example: + +as3935@0 { + compatible = "ams,as3935"; + reg = <0>; + spi-cpha; + interrupt-parent = <&gpio1>; + interrupts = <16 1>; + ams,tuning-capacitor-pf = <80>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt new file mode 100644 index 00000000000..448273a30a1 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt @@ -0,0 +1,29 @@ +Broadcom Generic Level 2 Interrupt Controller + +Required properties: + +- compatible: should be "brcm,l2-intc" +- reg: specifies the base physical address and size of the registers +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. Should be 1. +- interrupt-parent: specifies the phandle to the parent interrupt controller + this controller is cacaded from +- interrupts: specifies the interrupt line in the interrupt-parent irq space + to be used for cascading + +Optional properties: + +- brcm,irq-can-wake: If present, this means the L2 controller can be used as a + wakeup source for system suspend/resume. + +Example: + +hif_intr2_intc: interrupt-controller@f0441000 { + compatible = "brcm,l2-intc"; + reg = <0xf0441000 0x30>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&intc>; + interrupts = <0x0 0x20 0x0>; +}; diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-370-xp-mpic.txt index 5fc03134a99..5fc03134a99 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-370-xp-mpic.txt diff --git a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt new file mode 100644 index 00000000000..6fa4c737af2 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt @@ -0,0 +1,70 @@ +Samsung Exynos IOMMU H/W, System MMU (System Memory Management Unit) + +Samsung's Exynos architecture contains System MMUs that enables scattered +physical memory chunks visible as a contiguous region to DMA-capable peripheral +devices like MFC, FIMC, FIMD, GScaler, FIMC-IS and so forth. + +System MMU is an IOMMU and supports identical translation table format to +ARMv7 translation tables with minimum set of page properties including access +permissions, shareability and security protection. In addition, System MMU has +another capabilities like L2 TLB or block-fetch buffers to minimize translation +latency. + +System MMUs are in many to one relation with peripheral devices, i.e. single +peripheral device might have multiple System MMUs (usually one for each bus +master), but one System MMU can handle transactions from only one peripheral +device. The relation between a System MMU and the peripheral device needs to be +defined in device node of the peripheral device. + +MFC in all Exynos SoCs and FIMD, M2M Scalers and G2D in Exynos5420 has 2 System +MMUs. +* MFC has one System MMU on its left and right bus. +* FIMD in Exynos5420 has one System MMU for window 0 and 4, the other system MMU + for window 1, 2 and 3. +* M2M Scalers and G2D in Exynos5420 has one System MMU on the read channel and + the other System MMU on the write channel. +The drivers must consider how to handle those System MMUs. One of the idea is +to implement child devices or sub-devices which are the client devices of the +System MMU. + +Note: +The current DT binding for the Exynos System MMU is incomplete. +The following properties can be removed or changed, if found incompatible with +the "Generic IOMMU Binding" support for attaching devices to the IOMMU. + +Required properties: +- compatible: Should be "samsung,exynos-sysmmu" +- reg: A tuple of base address and size of System MMU registers. +- interrupt-parent: The phandle of the interrupt controller of System MMU +- interrupts: An interrupt specifier for interrupt signal of System MMU, + according to the format defined by a particular interrupt + controller. +- clock-names: Should be "sysmmu" if the System MMU is needed to gate its clock. + Optional "master" if the clock to the System MMU is gated by + another gate clock other than "sysmmu". + Exynos4 SoCs, there needs no "master" clock. + Exynos5 SoCs, some System MMUs must have "master" clocks. +- clocks: Required if the System MMU is needed to gate its clock. +- samsung,power-domain: Required if the System MMU is needed to gate its power. + Please refer to the following document: + Documentation/devicetree/bindings/arm/exynos/power_domain.txt + +Examples: + gsc_0: gsc@13e00000 { + compatible = "samsung,exynos5-gsc"; + reg = <0x13e00000 0x1000>; + interrupts = <0 85 0>; + samsung,power-domain = <&pd_gsc>; + clocks = <&clock CLK_GSCL0>; + clock-names = "gscl"; + }; + + sysmmu_gsc0: sysmmu@13E80000 { + compatible = "samsung,exynos-sysmmu"; + reg = <0x13E80000 0x1000>; + interrupt-parent = <&combiner>; + interrupts = <2 0>; + clock-names = "sysmmu", "master"; + clocks = <&clock CLK_SMMU_GSCL0>, <&clock CLK_GSCL0>; + samsung,power-domain = <&pd_gsc>; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt new file mode 100644 index 00000000000..87fe08abf36 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -0,0 +1,43 @@ +* Renesas VSP1 Video Processing Engine + +The VSP1 is a video processing engine that supports up-/down-scaling, alpha +blending, color space conversion and various other image processing features. +It can be found in the Renesas R-Car second generation SoCs. + +Required properties: + + - compatible: Must contain "renesas,vsp1" + + - reg: Base address and length of the registers block for the VSP1. + - interrupts: VSP1 interrupt specifier. + - clocks: A phandle + clock-specifier pair for the VSP1 functional clock. + + - renesas,#rpf: Number of Read Pixel Formatter (RPF) modules in the VSP1. + - renesas,#uds: Number of Up Down Scaler (UDS) modules in the VSP1. + - renesas,#wpf: Number of Write Pixel Formatter (WPF) modules in the VSP1. + + +Optional properties: + + - renesas,has-lif: Boolean, indicates that the LCD Interface (LIF) module is + available. + - renesas,has-lut: Boolean, indicates that the Look Up Table (LUT) module is + available. + - renesas,has-sru: Boolean, indicates that the Super Resolution Unit (SRU) + module is available. + + +Example: R8A7790 (R-Car H2) VSP1-S node + + vsp1@fe928000 { + compatible = "renesas,vsp1"; + reg = <0 0xfe928000 0 0x8000>; + interrupts = <0 267 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>; + + renesas,has-lut; + renesas,has-sru; + renesas,#rpf = <5>; + renesas,#uds = <3>; + renesas,#wpf = <4>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt index 653c90c34a7..1ee3bc09f31 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt @@ -6,10 +6,11 @@ The actual devices are instantiated from the child nodes of a Device Bus node. Required properties: - - compatible: Currently only Armada 370/XP SoC are supported, - with this compatible string: + - compatible: Armada 370/XP SoC are supported using the + "marvell,mvebu-devbus" compatible string. - marvell,mvebu-devbus + Orion5x SoC are supported using the + "marvell,orion-devbus" compatible string. - reg: A resource specifier for the register space. This is the base address of a chip select within @@ -22,7 +23,14 @@ Required properties: integer values for each chip-select line in use: 0 <physical address of mapping> <size> -Mandatory timing properties for child nodes: +Optional properties: + + - devbus,keep-config This property can optionally be used to keep + using the timing parameters set by the + bootloader. It makes all the timing properties + described below unused. + +Timing properties for child nodes: Read parameters: @@ -30,21 +38,26 @@ Read parameters: drive the AD bus after the completion of a device read. This prevents contentions on the Device Bus after a read cycle from a slow device. + Mandatory, except if devbus,keep-config is used. - - devbus,bus-width: Defines the bus width (e.g. <16>) + - devbus,bus-width: Defines the bus width, in bits (e.g. <16>). + Mandatory, except if devbus,keep-config is used. - devbus,badr-skew-ps: Defines the time delay from from A[2:0] toggle, to read data sample. This parameter is useful for synchronous pipelined devices, where the address precedes the read data by one or two cycles. + Mandatory, except if devbus,keep-config is used. - devbus,acc-first-ps: Defines the time delay from the negation of ALE[0] to the cycle that the first read data is sampled by the controller. + Mandatory, except if devbus,keep-config is used. - devbus,acc-next-ps: Defines the time delay between the cycle that samples data N and the cycle that samples data N+1 (in burst accesses). + Mandatory, except if devbus,keep-config is used. - devbus,rd-setup-ps: Defines the time delay between DEV_CSn assertion to DEV_OEn assertion. If set to 0 (default), @@ -52,6 +65,8 @@ Read parameters: This parameter has no affect on <acc-first-ps> parameter (no affect on first data sample). Set <rd-setup-ps> to a value smaller than <acc-first-ps>. + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. - devbus,rd-hold-ps: Defines the time between the last data sample to the de-assertion of DEV_CSn. If set to 0 (default), @@ -62,16 +77,20 @@ Read parameters: last data sampled. Also this parameter has no affect on <turn-off-ps> parameter. Set <rd-hold-ps> to a value smaller than <turn-off-ps>. + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. Write parameters: - devbus,ale-wr-ps: Defines the time delay from the ALE[0] negation cycle to the DEV_WEn assertion. + Mandatory. - devbus,wr-low-ps: Defines the time during which DEV_WEn is active. A[2:0] and Data are kept valid as long as DEV_WEn is active. This parameter defines the setup time of address and data to DEV_WEn rise. + Mandatory. - devbus,wr-high-ps: Defines the time during which DEV_WEn is kept inactive (high) between data beats of a burst write. @@ -79,10 +98,13 @@ Write parameters: <wr-high-ps> - <tick> ps. This parameter defines the hold time of address and data after DEV_WEn rise. + Mandatory. - devbus,sync-enable: Synchronous device enable. 1: True 0: False + Mandatory for "marvell,mvebu-devbus" compatible string, + except if devbus,keep-config is used. An example for an Armada XP GP board, with a 16 MiB NOR device as child is showed below. Note that the Device Bus driver is in charge of allocating diff --git a/Documentation/devicetree/bindings/mfd/bcm590xx.txt b/Documentation/devicetree/bindings/mfd/bcm590xx.txt index 1fe30e2b10d..be51a15e05f 100644 --- a/Documentation/devicetree/bindings/mfd/bcm590xx.txt +++ b/Documentation/devicetree/bindings/mfd/bcm590xx.txt @@ -19,7 +19,9 @@ Optional child nodes: The valid regulator node names for BCM59056 are: rfldo, camldo1, camldo2, simldo1, simldo2, sdldo, sdxldo, mmcldo1, mmcldo2, audldo, micldo, usbldo, vibldo, - csr, iosr1, iosr2, msr, sdsr1, sdsr2, vsr + csr, iosr1, iosr2, msr, sdsr1, sdsr2, vsr, + gpldo1, gpldo2, gpldo3, gpldo4, gpldo5, gpldo6, + vbus Example: pmu: bcm59056@8 { diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index 1413f39912d..8aba48821a8 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -10,6 +10,9 @@ Optional properties: - fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used Sub-nodes: +- codec: Contain the Audio Codec node. + - adc-port: Contain PMIC SSI port number used for ADC. + - dac-port: Contain PMIC SSI port number used for DAC. - leds : Contain the led nodes and initial register values in property "led-control". Number of register depends of used IC, for MC13783 is 6, for MC13892 is 4, for MC34708 is 1. See datasheet for bits definitions of diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 802e839b082..d81ba30c0d8 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -56,6 +56,20 @@ for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6], BUCK[3, 4], and BUCK[7, 8, 10] +On S2MPS14 the LDO10, LDO11 and LDO12 can be configured to external control +over GPIO. To turn this feature on this property must be added to the regulator +sub-node: + - samsung,ext-control-gpios: GPIO specifier for one GPIO + controlling this regulator (enable/disable); +Example: + LDO12 { + regulator-name = "V_EMMC_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + The regulator constraints inside the regulator nodes use the standard regulator bindings which are documented elsewhere. diff --git a/Documentation/devicetree/bindings/misc/arm-charlcd.txt b/Documentation/devicetree/bindings/misc/arm-charlcd.txt new file mode 100644 index 00000000000..e28e2aac47f --- /dev/null +++ b/Documentation/devicetree/bindings/misc/arm-charlcd.txt @@ -0,0 +1,18 @@ +ARM Versatile Character LCD +----------------------------------------------------- +This binding defines the character LCD interface found on ARM Versatile AB +and PB reference platforms. + +Required properties: +- compatible : "arm,versatile-clcd" +- reg : Location and size of character LCD registers + +Optional properties: +- interrupts - single interrupt for character LCD. The character LCD can + operate in polled mode without an interrupt. + +Example: + lcd@10008000 { + compatible = "arm,versatile-lcd"; + reg = <0x10008000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt index b8653ea9795..e5bc49f764d 100644 --- a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt @@ -12,7 +12,7 @@ extensions to the Synopsys Designware Mobile Storage Host Controller. Required Properties: * compatible: should be one of the following. - - "hisilicon,hi4511-dw-mshc": for controllers with hi4511 specific extentions. + - "hisilicon,hi4511-dw-mshc": for controllers with hi4511 specific extensions. Example: diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 2b584cae352..03796cf2d3e 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -4,12 +4,58 @@ The ARM PrimeCell MMCI PL180 and PL181 provides an interface for reading and writing to MultiMedia and SD cards alike. This file documents differences between the core properties described -by mmc.txt and the properties used by the mmci driver. +by mmc.txt and the properties used by the mmci driver. Using "st" as +the prefix for a property, indicates support by the ST Micro variant. Required properties: - compatible : contains "arm,pl18x", "arm,primecell". -- arm,primecell-periphid : contains the PrimeCell Peripheral ID. +- vmmc-supply : phandle to the regulator device tree node, mentioned + as the VCC/VDD supply in the eMMC/SD specs. Optional properties: -- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable -- mmc-cap-sd-highspeed : indicates whether SD is high speed capable +- arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides + the ID provided by the HW +- vqmmc-supply : phandle to the regulator device tree node, mentioned + as the VCCQ/VDD_IO supply in the eMMC/SD specs. +- st,sig-dir-dat0 : bus signal direction pin used for DAT[0]. +- st,sig-dir-dat2 : bus signal direction pin used for DAT[2]. +- st,sig-dir-dat31 : bus signal direction pin used for DAT[3] and DAT[1]. +- st,sig-dir-dat74 : bus signal direction pin used for DAT[4] to DAT[7]. +- st,sig-dir-cmd : cmd signal direction pin used for CMD. +- st,sig-pin-fbclk : feedback clock signal pin used. + +Deprecated properties: +- mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable. +- mmc-cap-sd-highspeed : indicates whether SD is high speed capable. + +Example: + +sdi0_per1@80126000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x80126000 0x1000>; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + + dmas = <&dma 29 0 0x2>, /* Logical - DevToMem */ + <&dma 29 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "tx"; + + clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>; + clock-names = "sdi", "apb_pclk"; + + max-frequency = <100000000>; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + cd-gpios = <&gpio2 31 0x4>; // 95 + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-cmd; + st,sig-pin-fbclk; + + vmmc-supply = <&ab8500_ldo_aux3_reg>; + vqmmc-supply = <&vmmci>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdi0_default_mode>; + pinctrl-1 = <&sdi0_sleep_mode>; +}; diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 328e990d254..42e0a9afa10 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -3,7 +3,7 @@ Samsung's SDHCI controller is used as a connectivity interface with external MMC, SD and eMMC storage mediums. This file documents differences between the core mmc properties described by mmc.txt and the properties used by the -Samsung implmentation of the SDHCI controller. +Samsung implementation of the SDHCI controller. Required SoC Specific Properties: - compatible: should be one of the following diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 5e1f31b5ff7..eb05255b678 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -43,7 +43,7 @@ Optional properties: ELM hardware engines should specify this device node in .dtsi Using ELM for ECC error correction frees some CPU cycles. -For inline partiton table parsing (optional): +For inline partition table parsing (optional): - #address-cells: should be set to 1 - #size-cells: should be set to 1 diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt index 420b3ab1889..4828c17bb78 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt @@ -30,7 +30,7 @@ Optional properties: - gpmc,XXX Additional GPMC timings and settings parameters. See Documentation/devicetree/bindings/bus/ti-gpmc.txt -Optional properties for partiton table parsing: +Optional properties for partition table parsing: - #address-cells: should be set to 1 - #size-cells: should be set to 1 diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt index b7529424ac8..5d8fa527c49 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt @@ -17,7 +17,7 @@ Optional properties: - dma-channel: DMA Channel index -For inline partiton table parsing (optional): +For inline partition table parsing (optional): - #address-cells: should be set to 1 - #size-cells: should be set to 1 diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt index c79bab02536..8dbcf8295c6 100644 --- a/Documentation/devicetree/bindings/net/mdio-gpio.txt +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -14,7 +14,7 @@ node. Example: aliases { - mdio-gpio0 = <&mdio0>; + mdio-gpio0 = &mdio0; }; mdio0: mdio { diff --git a/Documentation/devicetree/bindings/pci/host-generic-pci.txt b/Documentation/devicetree/bindings/pci/host-generic-pci.txt new file mode 100644 index 00000000000..f0b0436807b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/host-generic-pci.txt @@ -0,0 +1,100 @@ +* Generic PCI host controller + +Firmware-initialised PCI host controllers and PCI emulations, such as the +virtio-pci implementations found in kvmtool and other para-virtualised +systems, do not require driver support for complexities such as regulator +and clock management. In fact, the controller may not even require the +configuration of a control interface by the operating system, instead +presenting a set of fixed windows describing a subset of IO, Memory and +Configuration Spaces. + +Such a controller can be described purely in terms of the standardized device +tree bindings communicated in pci.txt: + + +Properties of the host controller node: + +- compatible : Must be "pci-host-cam-generic" or "pci-host-ecam-generic" + depending on the layout of configuration space (CAM vs + ECAM respectively). + +- device_type : Must be "pci". + +- ranges : As described in IEEE Std 1275-1994, but must provide + at least a definition of non-prefetchable memory. One + or both of prefetchable Memory and IO Space may also + be provided. + +- bus-range : Optional property (also described in IEEE Std 1275-1994) + to indicate the range of bus numbers for this controller. + If absent, defaults to <0 255> (i.e. all buses). + +- #address-cells : Must be 3. + +- #size-cells : Must be 2. + +- reg : The Configuration Space base address and size, as accessed + from the parent bus. + + +Properties of the /chosen node: + +- linux,pci-probe-only + : Optional property which takes a single-cell argument. + If '0', then Linux will assign devices in its usual manner, + otherwise it will not try to assign devices and instead use + them as they are configured already. + +Configuration Space is assumed to be memory-mapped (as opposed to being +accessed via an ioport) and laid out with a direct correspondence to the +geography of a PCI bus address by concatenating the various components to +form an offset. + +For CAM, this 24-bit offset is: + + cfg_offset(bus, device, function, register) = + bus << 16 | device << 11 | function << 8 | register + +Whilst ECAM extends this by 4 bits to accomodate 4k of function space: + + cfg_offset(bus, device, function, register) = + bus << 20 | device << 15 | function << 12 | register + +Interrupt mapping is exactly as described in `Open Firmware Recommended +Practice: Interrupt Mapping' and requires the following properties: + +- #interrupt-cells : Must be 1 + +- interrupt-map : <see aforementioned specification> + +- interrupt-map-mask : <see aforementioned specification> + + +Example: + +pci { + compatible = "pci-host-cam-generic" + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0x1>; + + // CPU_PHYSICAL(2) SIZE(2) + reg = <0x0 0x40000000 0x0 0x1000000>; + + // BUS_ADDRESS(3) CPU_PHYSICAL(2) SIZE(2) + ranges = <0x01000000 0x0 0x01000000 0x0 0x01000000 0x0 0x00010000>, + <0x02000000 0x0 0x41000000 0x0 0x41000000 0x0 0x3f000000>; + + + #interrupt-cells = <0x1>; + + // PCI_DEVICE(3) INT#(1) CONTROLLER(PHANDLE) CONTROLLER_DATA(3) + interrupt-map = < 0x0 0x0 0x0 0x1 &gic 0x0 0x4 0x1 + 0x800 0x0 0x0 0x1 &gic 0x0 0x5 0x1 + 0x1000 0x0 0x0 0x1 &gic 0x0 0x6 0x1 + 0x1800 0x0 0x0 0x1 &gic 0x0 0x7 0x1>; + + // PCI_DEVICE(3) INT#(1) + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; +} diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt new file mode 100644 index 00000000000..d8ef5bf50f1 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -0,0 +1,66 @@ +Renesas AHB to PCI bridge +------------------------- + +This is the bridge used internally to connect the USB controllers to the +AHB. There is one bridge instance per USB port connected to the internal +OHCI and EHCI controllers. + +Required properties: +- compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; + "renesas,pci-r8a7791" for the R8A7791 SoC. +- reg: A list of physical regions to access the device: the first is + the operational registers for the OHCI/EHCI controllers and the + second is for the bridge configuration and control registers. +- interrupts: interrupt for the device. +- clocks: The reference to the device clock. +- bus-range: The PCI bus number range; as this is a single bus, the range + should be specified as the same value twice. +- #address-cells: must be 3. +- #size-cells: must be 2. +- #interrupt-cells: must be 1. +- interrupt-map: standard property used to define the mapping of the PCI + interrupts to the GIC interrupts. +- interrupt-map-mask: standard property that helps to define the interrupt + mapping. + +Example SoC configuration: + + pci0: pci@ee090000 { + compatible = "renesas,pci-r8a7790"; + clocks = <&mstp7_clks R8A7790_CLK_EHCI>; + reg = <0x0 0xee090000 0x0 0xc00>, + <0x0 0xee080000 0x0 0x1100>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + + bus-range = <0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xff00 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; + + pci@0,1 { + reg = <0x800 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + + pci@0,2 { + reg = <0x1000 0 0 0 0>; + device_type = "pci"; + phys = <&usbphy 0 0>; + phy-names = "usb"; + }; + }; + +Example board setup: + +&pci0 { + status = "okay"; + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; +}; diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt new file mode 100644 index 00000000000..29d3b989d3b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -0,0 +1,47 @@ +* Renesas RCar PCIe interface + +Required properties: +- compatible: should contain one of the following + "renesas,pcie-r8a7779", "renesas,pcie-r8a7790", "renesas,pcie-r8a7791" +- reg: base address and length of the pcie controller registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- bus-range: PCI bus numbers covered +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- interrupts: two interrupt sources for MSI interrupts, followed by interrupt + source for hardware related interrupts (e.g. link speed change). +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: clock specifiers for the PCIe controller + and PCIe bus clocks. +- clock-names: from common clock binding: should be "pcie" and "pcie_bus". + +Example: + +SoC specific DT Entry: + + pcie: pcie@fe000000 { + compatible = "renesas,pcie-r8a7791"; + reg = <0 0xfe000000 0 0x80000>; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x00 0xff>; + device_type = "pci"; + ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000 + 0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000 + 0x02000000 0 0x30000000 0 0x30000000 0 0x08000000 + 0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>; + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000 + 0x42000000 2 0x00000000 2 0x00000000 0 0x40000000>; + interrupts = <0 116 4>, <0 117 4>, <0 118 4>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 116 4>; + clocks = <&mstp3_clks R8A7791_CLK_PCIE>, <&pcie_bus_clk>; + clock-names = "pcie", "pcie_bus"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index b422e38946d..2049261d8c3 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -114,3 +114,50 @@ Example: compatible = "samsung,exynos-sataphy-i2c"; reg = <0x38>; }; + +Samsung Exynos5 SoC series USB DRD PHY controller +-------------------------------------------------- + +Required properties: +- compatible : Should be set to one of the following supported values: + - "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC, + - "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC. +- reg : Register offset and length of USB DRD PHY register set; +- clocks: Clock IDs array as required by the controller +- clock-names: names of clocks correseponding to IDs in the clock property; + Required clocks: + - phy: main PHY clock (same as USB DRD controller i.e. DWC3 IP clock), + used for register access. + - ref: PHY's reference clock (usually crystal clock), used for + PHY operations, associated by phy name. It is used to + determine bit values for clock settings register. + For Exynos5420 this is given as 'sclk_usbphy30' in CMU. +- samsung,pmu-syscon: phandle for PMU system controller interface, used to + control pmu registers for power isolation. +- #phy-cells : from the generic PHY bindings, must be 1; + +For "samsung,exynos5250-usbdrd-phy" and "samsung,exynos5420-usbdrd-phy" +compatible PHYs, the second cell in the PHY specifier identifies the +PHY id, which is interpreted as follows: + 0 - UTMI+ type phy, + 1 - PIPE3 type phy, + +Example: + usbdrd_phy: usbphy@12100000 { + compatible = "samsung,exynos5250-usbdrd-phy"; + reg = <0x12100000 0x100>; + clocks = <&clock 286>, <&clock 1>; + clock-names = "phy", "ref"; + samsung,pmu-syscon = <&pmu_system_controller>; + #phy-cells = <1>; + }; + +- aliases: For SoCs like Exynos5420 having multiple USB 3.0 DRD PHY controllers, + 'usbdrd_phy' nodes should have numbered alias in the aliases node, + in the form of usbdrdphyN, N = 0, 1... (depending on number of + controllers). +Example: + aliases { + usbdrdphy0 = &usb3_phy0; + usbdrdphy1 = &usb3_phy1; + }; diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index a82361b6201..16528b9eb56 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -2,15 +2,26 @@ Allwinner sun4i USB PHY ----------------------- Required properties: -- compatible : should be one of "allwinner,sun4i-a10-usb-phy", - "allwinner,sun5i-a13-usb-phy" or "allwinner,sun7i-a20-usb-phy" +- compatible : should be one of + * allwinner,sun4i-a10-usb-phy + * allwinner,sun5i-a13-usb-phy + * allwinner,sun6i-a31-usb-phy + * allwinner,sun7i-a20-usb-phy - reg : a list of offset + length pairs -- reg-names : "phy_ctrl", "pmu1" and for sun4i or sun7i "pmu2" +- reg-names : + * "phy_ctrl" + * "pmu1" + * "pmu2" for sun4i, sun6i or sun7i - #phy-cells : from the generic phy bindings, must be 1 -- clocks : phandle + clock specifier for the phy clock -- clock-names : "usb_phy" +- clocks : phandle + clock specifier for the phy clocks +- clock-names : + * "usb_phy" for sun4i, sun5i or sun7i + * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i - resets : a list of phandle + reset specifier pairs -- reset-names : "usb0_reset", "usb1_reset" and for sun4i or sun7i "usb2_reset" +- reset-names : + * "usb0_reset" + * "usb1_reset" + * "usb2_reset" for sun4i, sun6i or sun7i Example: usbphy: phy@0x01c13400 { diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index 788fb0fa376..9ce458f3294 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -32,6 +32,11 @@ Required properties: - reg : Address and length of the register set for the device. - #phy-cells: determine the number of cells that should be given in the phandle while referencing this phy. + - clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + - clock-names: should include: + * "wkupclk" - wakeup clock. + * "refclk" - reference clock (optional). Optional properties: - ctrl-module : phandle of the control module used by PHY driver to power on @@ -44,6 +49,8 @@ usb2phy@4a0ad080 { reg = <0x4a0ad080 0x58>; ctrl-module = <&omap_control_usb>; #phy-cells = <0>; + clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>; + clock-names = "wkupclk", "refclk"; }; TI PIPE3 PHY diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index dff0e5f995e..d8d065608ec 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -6,8 +6,13 @@ the first two functions being GPIO in and out. The configuration on the pins includes drive strength and pull-up. Required properties: -- compatible: "allwinner,<soc>-pinctrl". Supported SoCs for now are: - sun5i-a13. +- compatible: Should be one of the followings (depending on you SoC): + "allwinner,sun4i-a10-pinctrl" + "allwinner,sun5i-a10s-pinctrl" + "allwinner,sun5i-a13-pinctrl" + "allwinner,sun6i-a31-pinctrl" + "allwinner,sun6i-a31-r-pinctrl" + "allwinner,sun7i-a20-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt index 67a5db95f18..4eaae32821a 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt @@ -73,9 +73,9 @@ Optional Properties (for standard pins): Otherwise: 0: fast slew rate 1: normal slew rate -- input-enable: No arguements. Enable input (does not affect +- input-enable: No arguments. Enable input (does not affect output.) -- input-disable: No arguements. Disable input (does not affect +- input-disable: No arguments. Disable input (does not affect output.) - drive-strength: Integer. Drive strength in mA. Valid values are 2, 4, 6, 8, 10, 12, 14, 16 mA. @@ -99,9 +99,9 @@ Optional Properties (for I2C pins): Otherwise: 0: fast slew rate 1: normal slew rate -- input-enable: No arguements. Enable input (does not affect +- input-enable: No arguments. Enable input (does not affect output.) -- input-disable: No arguements. Disable input (does not affect +- input-disable: No arguments. Disable input (does not affect output.) Optional Properties (for HDMI pins): @@ -111,9 +111,9 @@ Optional Properties (for HDMI pins): - slew-rate: Integer. Controls slew rate. 0: Standard(100kbps)& Fast(400kbps) mode 1: Highspeed (3.4Mbps) mode -- input-enable: No arguements. Enable input (does not affect +- input-enable: No arguments. Enable input (does not affect output.) -- input-disable: No arguements. Disable input (does not affect +- input-disable: No arguments. Disable input (does not affect output.) Example: diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt new file mode 100644 index 00000000000..b1b595220f1 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt @@ -0,0 +1,36 @@ +* Freescale i.MX6 SoloX IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: "fsl,imx6sx-iomuxc" +- fsl,pins: each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val + input_val> are specified using a PIN_FUNC_ID macro, which can be found in + imx6sx-pinfunc.h under device tree source folder. The last integer CONFIG is + the pad setting value like pull-up on this pin. Please refer to i.MX6 SoloX + Reference Manual for detailed CONFIG settings. + +CONFIG bits definition: +PAD_CTL_HYS (1 << 16) +PAD_CTL_PUS_100K_DOWN (0 << 14) +PAD_CTL_PUS_47K_UP (1 << 14) +PAD_CTL_PUS_100K_UP (2 << 14) +PAD_CTL_PUS_22K_UP (3 << 14) +PAD_CTL_PUE (1 << 13) +PAD_CTL_PKE (1 << 12) +PAD_CTL_ODE (1 << 11) +PAD_CTL_SPEED_LOW (0 << 6) +PAD_CTL_SPEED_MED (1 << 6) +PAD_CTL_SPEED_HIGH (3 << 6) +PAD_CTL_DSE_DISABLE (0 << 3) +PAD_CTL_DSE_260ohm (1 << 3) +PAD_CTL_DSE_130ohm (2 << 3) +PAD_CTL_DSE_87ohm (3 << 3) +PAD_CTL_DSE_65ohm (4 << 3) +PAD_CTL_DSE_52ohm (5 << 3) +PAD_CTL_DSE_43ohm (6 << 3) +PAD_CTL_DSE_37ohm (7 << 3) +PAD_CTL_SRE_FAST (1 << 0) +PAD_CTL_SRE_SLOW (0 << 0) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt new file mode 100644 index 00000000000..27570a3a174 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt @@ -0,0 +1,91 @@ +* Marvell Orion SoC pinctrl driver for mpp + +Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding +part and usage. + +Required properties: +- compatible: "marvell,88f5181l-pinctrl", "marvell,88f5182-pinctrl", + "marvell,88f5281-pinctrl" + +- reg: two register areas, the first one describing the first two + contiguous MPP registers, and the second one describing the single + final MPP register, separated from the previous one. + +Available mpp pins/groups and functions: +Note: brackets (x) are not part of the mpp name for marvell,function and given +only for more detailed description in this document. + +* Marvell Orion 88f5181l + +name pins functions +================================================================================ +mpp0 0 pcie(rstout), pci(req2), gpio +mpp1 1 gpio, pci(gnt2) +mpp2 2 gpio, pci(req3), pci-1(pme) +mpp3 3 gpio, pci(gnt3) +mpp4 4 gpio, pci(req4) +mpp5 5 gpio, pci(gnt4) +mpp6 6 gpio, pci(req5), pci-1(clk) +mpp7 7 gpio, pci(gnt5), pci-1(clk) +mpp8 8 gpio, ge(col) +mpp9 9 gpio, ge(rxerr) +mpp10 10 gpio, ge(crs) +mpp11 11 gpio, ge(txerr) +mpp12 12 gpio, ge(txd4) +mpp13 13 gpio, ge(txd5) +mpp14 14 gpio, ge(txd6) +mpp15 15 gpio, ge(txd7) +mpp16 16 ge(rxd4) +mpp17 17 ge(rxd5) +mpp18 18 ge(rxd6) +mpp19 19 ge(rxd7) + +* Marvell Orion 88f5182 + +name pins functions +================================================================================ +mpp0 0 pcie(rstout), pci(req2), gpio +mpp1 1 gpio, pci(gnt2) +mpp2 2 gpio, pci(req3), pci-1(pme) +mpp3 3 gpio, pci(gnt3) +mpp4 4 gpio, pci(req4), bootnand(re), sata0(prsnt) +mpp5 5 gpio, pci(gnt4), bootnand(we), sata1(prsnt) +mpp6 6 gpio, pci(req5), nand(re0), sata0(act) +mpp7 7 gpio, pci(gnt5), nand(we0), sata1(act) +mpp8 8 gpio, ge(col) +mpp9 9 gpio, ge(rxerr) +mpp10 10 gpio, ge(crs) +mpp11 11 gpio, ge(txerr) +mpp12 12 gpio, ge(txd4), nand(re1), sata0(ledprsnt) +mpp13 13 gpio, ge(txd5), nand(we1), sata1(ledprsnt) +mpp14 14 gpio, ge(txd6), nand(re2), sata0(ledact) +mpp15 15 gpio, ge(txd7), nand(we2), sata1(ledact) +mpp16 16 uart1(rxd), ge(rxd4), gpio +mpp17 17 uart1(txd), ge(rxd5), gpio +mpp18 18 uart1(cts), ge(rxd6), gpio +mpp19 19 uart1(rts), ge(rxd7), gpio + +* Marvell Orion 88f5281 + +name pins functions +================================================================================ +mpp0 0 pcie(rstout), pci(req2), gpio +mpp1 1 gpio, pci(gnt2) +mpp2 2 gpio, pci(req3), pci(pme) +mpp3 3 gpio, pci(gnt3) +mpp4 4 gpio, pci(req4), bootnand(re) +mpp5 5 gpio, pci(gnt4), bootnand(we) +mpp6 6 gpio, pci(req5), nand(re0) +mpp7 7 gpio, pci(gnt5), nand(we0) +mpp8 8 gpio, ge(col) +mpp9 9 gpio, ge(rxerr) +mpp10 10 gpio, ge(crs) +mpp11 11 gpio, ge(txerr) +mpp12 12 gpio, ge(txd4), nand(re1) +mpp13 13 gpio, ge(txd5), nand(we1) +mpp14 14 gpio, ge(txd6), nand(re2) +mpp15 15 gpio, ge(txd7), nand(we2) +mpp16 16 uart1(rxd), ge(rxd4) +mpp17 17 uart1(txd), ge(rxd5) +mpp18 18 uart1(cts), ge(rxd6) +mpp19 19 uart1(rts), ge(rxd7) diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index 4414163e76d..fa40a177164 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -156,6 +156,7 @@ input-disable - disable input on pin (no effect on output) input-schmitt-enable - enable schmitt-trigger mode input-schmitt-disable - disable schmitt-trigger mode input-debounce - debounce mode with debound time X +power-source - select between different power supplies low-power-enable - enable low power mode low-power-disable - disable low power mode output-low - set the pin to output mode with low level diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt new file mode 100644 index 00000000000..7181f925aca --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt @@ -0,0 +1,88 @@ +Qualcomm APQ8064 TLMM block + +Required properties: +- compatible: "qcom,apq8064-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Qualcomm's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength, + output-low, output-high. + +Non-empty subnodes must specify the 'pins' property. + +Valid values for pins are: + gpio0-gpio89 + +Valid values for function are: + cam_mclk, codec_mic_i2s, codec_spkr_i2s, gsbi1, gsbi2, gsbi3, gsbi4, + gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, + gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1, + gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm, + riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, + +Example: + + msmgpio: pinctrl@800000 { + compatible = "qcom,apq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 32 0x4>; + + pinctrl-names = "default"; + pinctrl-0 = <&gsbi5_uart_default>; + + gsbi5_uart_default: gsbi5_uart_default { + mux { + pins = "gpio51", "gpio52"; + function = "gsbi5"; + }; + + tx { + pins = "gpio51"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio52"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt new file mode 100644 index 00000000000..e0d35a40981 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt @@ -0,0 +1,95 @@ +Qualcomm IPQ8064 TLMM block + +Required properties: +- compatible: "qcom,ipq8064-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Qualcomm's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength, + output-low, output-high. + +Non-empty subnodes must specify the 'pins' property. + +Valid values for qcom,pins are: + gpio0-gpio68 + Supports mux, bias, and drive-strength + + sdc3_clk, sdc3_cmd, sdc3_data + Supports bias and drive-strength + + +Valid values for function are: + mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gsbi1, gsbi2, gsbi4, gsbi5, + gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1, + spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata, + pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt, + pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren, + pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n, + pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold + +Example: + + pinmux: pinctrl@800000 { + compatible = "qcom,ipq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 32 0x4>; + + pinctrl-names = "default"; + pinctrl-0 = <&gsbi5_uart_default>; + + gsbi5_uart_default: gsbi5_uart_default { + mux { + pins = "gpio18", "gpio19"; + function = "gsbi5"; + }; + + tx { + pins = "gpio18"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio19"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt index 9fb89e3f61e..73262b575df 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -50,7 +50,27 @@ Valid values for pins are: Supports bias and drive-strength Valid values for function are: - blsp_i2c2, blsp_i2c6, blsp_i2c11, blsp_spi1, blsp_uart2, blsp_uart8, slimbus + cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm, + blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1, + blsp_uim2, blsp_uart2, blsp_i2c2, blsp_spi2, + blsp_uim3, blsp_uart3, blsp_i2c3, blsp_spi3, + blsp_uim4, blsp_uart4, blsp_i2c4, blsp_spi4, + blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5, + blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6, + blsp_uim7, blsp_uart7, blsp_i2c7, blsp_spi7, + blsp_uim8, blsp_uart8, blsp_i2c8, blsp_spi8, + blsp_uim9, blsp_uart9, blsp_i2c9, blsp_spi9, + blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10, + blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11, + blsp_uim12, blsp_uart12, blsp_i2c12, blsp_spi12, + blsp_spi1_cs1, blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2 + blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3, + sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0, cci_timer1, + cci_timer2, cci_timer3, cci_async_in0, cci_async_in1, cci_async_in2, + cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc, + hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk, + gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s, + ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus (Note that this is not yet the complete list of functions) diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index f378d342aae..cefef741a40 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -21,13 +21,23 @@ defined as gpio sub-nodes of the pinmux controller. Required properties for iomux controller: - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" + - rockchip,grf: phandle referencing a syscon providing the + "general register files" + +Optional properties for iomux controller: + - rockchip,pmu: phandle referencing a syscon providing the pmu registers + as some SoCs carry parts of the iomux controller registers there. + Required for at least rk3188 and rk3288. + +Deprecated properties for iomux controller: - reg: first element is the general register space of the iomux controller - second element is the separate pull register space of the rk3188 + It should be large enough to contain also separate pull registers. + second element is the separate pull register space of the rk3188. + Use rockchip,grf and rockchip,pmu described above instead. Required properties for gpio sub nodes: - compatible: "rockchip,gpio-bank", "rockchip,rk3188-gpio-bank0" - reg: register of the gpio bank (different than the iomux registerset) - second element: separate pull register for rk3188 bank0 - interrupts: base interrupt of the gpio bank in the interrupt controller - clocks: clock that drives this bank - gpio-controller: identifies the node as a gpio controller and pin bank. @@ -39,6 +49,10 @@ Required properties for gpio sub nodes: cells should use the standard two-cell scheme described in bindings/interrupt-controller/interrupts.txt +Deprecated properties for gpio sub nodes: + - reg: second element: separate pull register for rk3188 bank0, use + rockchip,pmu described above instead + Required properties for pin configuration node: - rockchip,pins: 3 integers array, represents a group of pins mux and config setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>. @@ -54,7 +68,8 @@ Examples: pinctrl@20008000 { compatible = "rockchip,rk3066a-pinctrl"; - reg = <0x20008000 0x150>; + rockchip,grf = <&grf>; + #address-cells = <1>; #size-cells = <1>; ranges; @@ -103,16 +118,15 @@ Example for rk3188: pinctrl@20008000 { compatible = "rockchip,rk3188-pinctrl"; - reg = <0x20008000 0xa0>, - <0x20008164 0x1a0>; + rockchip,grf = <&grf>; + rockchip,pmu = <&pmu>; #address-cells = <1>; #size-cells = <1>; ranges; gpio0: gpio0@0x2000a000 { compatible = "rockchip,rk3188-gpio-bank0"; - reg = <0x2000a000 0x100>, - <0x20004064 0x8>; + reg = <0x2000a000 0x100>; interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk_gates8 9>; diff --git a/Documentation/devicetree/bindings/power/reset/keystone-reset.txt b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt new file mode 100644 index 00000000000..c82f12e2d85 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt @@ -0,0 +1,67 @@ +* Device tree bindings for Texas Instruments keystone reset + +This node is intended to allow SoC reset in case of software reset +of selected watchdogs. + +The Keystone SoCs can contain up to 4 watchdog timers to reset +SoC. Each watchdog timer event input is connected to the Reset Mux +block. The Reset Mux block can be configured to cause reset or not. + +Additionally soft or hard reset can be configured. + +Required properties: + +- compatible: ti,keystone-reset + +- ti,syscon-pll: phandle/offset pair. The phandle to syscon used to + access pll controller registers and the offset to use + reset control registers. + +- ti,syscon-dev: phandle/offset pair. The phandle to syscon used to + access device state control registers and the offset + in order to use mux block registers for all watchdogs. + +Optional properties: + +- ti,soft-reset: Boolean option indicating soft reset. + By default hard reset is used. + +- ti,wdt-list: WDT list that can cause SoC reset. It's not related + to WDT driver, it's just needed to enable a SoC related + reset that's triggered by one of WDTs. The list is + in format: <0>, <2>; It can be in random order and + begins from 0 to 3, as keystone can contain up to 4 SoC + reset watchdogs and can be in random order. + +Example 1: +Setup keystone reset so that in case software reset or +WDT0 is triggered it issues hard reset for SoC. + +pllctrl: pll-controller@02310000 { + compatible = "ti,keystone-pllctrl", "syscon"; + reg = <0x02310000 0x200>; +}; + +devctrl: device-state-control@02620000 { + compatible = "ti,keystone-devctrl", "syscon"; + reg = <0x02620000 0x1000>; +}; + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl 0xe4>; + ti,syscon-dev = <&devctrl 0x328>; + ti,wdt-list = <0>; +}; + +Example 2: +Setup keystone reset so that in case of software reset or +WDT0 or WDT2 is triggered it issues soft reset for SoC. + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl 0xe4>; + ti,syscon-dev = <&devctrl 0x328>; + ti,wdt-list = <0>, <2>; + ti,soft-reset; +}; diff --git a/Documentation/devicetree/bindings/power_supply/axxia-reset.txt b/Documentation/devicetree/bindings/power_supply/axxia-reset.txt new file mode 100644 index 00000000000..47e720d249d --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/axxia-reset.txt @@ -0,0 +1,20 @@ +Axxia Restart Driver + +This driver can do reset of the Axxia SoC. It uses the registers in the syscon +block to initiate a chip reset. + +Required Properties: + -compatible: "lsi,axm55xx-reset" + -syscon: phandle to the syscon node. + +Example: + + syscon: syscon@2010030000 { + compatible = "lsi,axxia-syscon", "syscon"; + reg = <0x20 0x10030000 0 0x2000>; + }; + + reset: reset@2010031000 { + compatible = "lsi,axm55xx-reset"; + syscon = <&syscon>; + }; diff --git a/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt index d7217260589..5bc63551319 100644 --- a/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt +++ b/Documentation/devicetree/bindings/powerpc/4xx/reboot.txt @@ -1,7 +1,7 @@ Reboot property to control system reboot on PPC4xx systems: By setting "reset_type" to one of the following values, the default -software reset mechanism may be overidden. Here the possible values of +software reset mechanism may be overridden. Here the possible values of "reset_type": 1 - PPC4xx core reset diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt index 9d54eb5a295..18a88100af9 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/dcsr.txt @@ -82,7 +82,7 @@ PROPERTIES Which event source asserted the interrupt is captured in an EPU Interrupt Status Register (EPISR0,EPISR1). - Interrupt numbers are lised in order (perfmon, event0, event1). + Interrupt numbers are listed in order (perfmon, event0, event1). - interrupt-parent Usage: required diff --git a/Documentation/devicetree/bindings/regulator/ltc3589.txt b/Documentation/devicetree/bindings/regulator/ltc3589.txt new file mode 100644 index 00000000000..80105303614 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/ltc3589.txt @@ -0,0 +1,99 @@ +Linear Technology LTC3589, LTC3589-1, and LTC3589-2 8-output regulators + +Required properties: +- compatible: "lltc,ltc3589", "lltc,ltc3589-1" or "lltc,ltc3589-2" +- reg: I2C slave address + +Required child node: +- regulators: Contains eight regulator child nodes sw1, sw2, sw3, bb-out, + ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as + documented in Documentation/devicetree/bindings/regulator/regulator.txt. + +Each regulator is defined using the standard binding for regulators. The +nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify +the resistor values of their external feedback voltage dividers: + +Required properties (not on ldo3, ldo4): +- lltc,fb-voltage-divider: An array of two integers containing the resistor + values R1 and R2 of the feedback voltage divider in ohms. + +Regulators sw1, sw2, sw3, and ldo2 can regulate the feedback reference from +0.3625 V to 0.75 V in 12.5 mV steps. The output voltage thus ranges between +0.3625 * (1 + R1/R2) V and 0.75 * (1 + R1/R2) V. Regulators bb-out and ldo1 +have a fixed 0.8 V reference and thus output 0.8 * (1 + R1/R2) V. The ldo3 +regulator is fixed to 1.8 V on LTC3589 and to 2.8 V on LTC3589-1,2. The ldo4 +regulator can output between 1.8 V and 3.3 V on LTC3589 and between 1.2 V +and 3.2 V on LTC3589-1,2 in four steps. The ldo1 standby regulator can not +be disabled and thus should have the regulator-always-on property set. + +Example: + + ltc3589: pmic@34 { + compatible = "lltc,ltc3589-1"; + reg = <0x34>; + + regulators { + sw1_reg: sw1 { + regulator-min-microvolt = <591930>; + regulator-max-microvolt = <1224671>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456803>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-min-microvolt = <1341250>; + regulator-max-microvolt = <2775000>; + lltc,fb-voltage-divider = <270000 100000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + bb_out_reg: bb-out { + regulator-min-microvolt = <3387341>; + regulator-max-microvolt = <3387341>; + lltc,fb-voltage-divider = <511000 158000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + regulator-min-microvolt = <1306329>; + regulator-max-microvolt = <1306329>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456806>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3200000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index e2c7f1e7251..86074334e34 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -12,7 +12,7 @@ Optional properties: - regulator-allow-bypass: allow the regulator to go into bypass mode - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) - For hardwares which support disabling ramp rate, it should be explicitly + For hardware which supports disabling ramp rate, it should be explicitly intialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. - regulator-enable-ramp-delay: The time taken, in microseconds, for the supply rail to reach the target voltage, plus/minus whatever tolerance the board diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt index 313a60ba61d..340980239ea 100644 --- a/Documentation/devicetree/bindings/regulator/tps65090.txt +++ b/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -21,6 +21,10 @@ Optional properties: number should be provided. If it is externally controlled and no GPIO entry then driver will just configure this rails as external control and will not provide any enable/disable APIs. +- ti,overcurrent-wait: This is applicable to FET registers, which have a + poorly defined "overcurrent wait" field. If this property is present it + should be between 0 - 3. If this property isn't present we won't touch the + "overcurrent wait" field and we'll leave it to the BIOS/EC to deal with. Each regulator is defined using the standard binding for regulators. diff --git a/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt b/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt new file mode 100644 index 00000000000..c8f77571488 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/allwinner,sunxi-clock-reset.txt @@ -0,0 +1,21 @@ +Allwinner sunxi Peripheral Reset Controller +=========================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be one of the following: + "allwinner,sun6i-a31-ahb1-reset" + "allwinner,sun6i-a31-clock-reset" +- reg: should be register base and length as documented in the + datasheet +- #reset-cells: 1, see below + +example: + +ahb1_rst: reset@01c202c0 { + #reset-cells = <1>; + compatible = "allwinner,sun6i-a31-ahb1-reset"; + reg = <0x01c202c0 0xc>; +}; diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt b/Documentation/devicetree/bindings/reset/socfpga-reset.txt index ecdb57d69db..32c1c8bfd5d 100644 --- a/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt +++ b/Documentation/devicetree/bindings/reset/socfpga-reset.txt @@ -3,9 +3,11 @@ Altera SOCFPGA Reset Manager Required properties: - compatible : "altr,rst-mgr" - reg : Should contain 1 register ranges(address and length) +- #reset-cells: 1 Example: rstmgr@ffd05000 { + #reset-cells = <1>; compatible = "altr,rst-mgr"; reg = <0xffd05000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt index 17c1042b2df..a6391e70a8f 100644 --- a/Documentation/devicetree/bindings/serial/atmel-usart.txt +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt @@ -13,8 +13,9 @@ Required properties: Optional properties: - atmel,use-dma-rx: use of PDC or DMA for receiving data - atmel,use-dma-tx: use of PDC or DMA for transmitting data -- rts-gpios: specify a GPIO for RTS line. It will use specified PIO instead of the peripheral - function pin for the USART RTS feature. If unsure, don't specify this property. +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively. + It will use specified PIO instead of the peripheral function pin for the USART feature. + If unsure, don't specify this property. - add dma bindings for dma transfer: - dmas: DMA specifier, consisting of a phandle to DMA controller node, memory peripheral interface and USART DMA channel ID, FIFO configuration. @@ -35,7 +36,12 @@ Example: clock-names = "usart"; atmel,use-dma-rx; atmel,use-dma-tx; - rts-gpios = <&pioD 15 0>; + rts-gpios = <&pioD 15 GPIO_ACTIVE_LOW>; + cts-gpios = <&pioD 16 GPIO_ACTIVE_LOW>; + dtr-gpios = <&pioD 17 GPIO_ACTIVE_LOW>; + dsr-gpios = <&pioD 18 GPIO_ACTIVE_LOW>; + dcd-gpios = <&pioD 20 GPIO_ACTIVE_LOW>; + rng-gpios = <&pioD 19 GPIO_ACTIVE_LOW>; }; - use DMA: diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt new file mode 100644 index 00000000000..246c795668d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt @@ -0,0 +1,33 @@ +* NXP SC16IS7xx advanced Universal Asynchronous Receiver-Transmitter (UART) + +Required properties: +- compatible: Should be one of the following: + - "nxp,sc16is740" for NXP SC16IS740, + - "nxp,sc16is741" for NXP SC16IS741, + - "nxp,sc16is750" for NXP SC16IS750, + - "nxp,sc16is752" for NXP SC16IS752, + - "nxp,sc16is760" for NXP SC16IS760, + - "nxp,sc16is762" for NXP SC16IS762. +- reg: I2C address of the SC16IS7xx device. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this IC. +- interrupts: Should contain the UART interrupt +- clocks: Reference to the IC source clock. + +Optional properties: +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be two. The first cell is the GPIO number and + the second cell is used to specify the GPIO polarity: + 0 = active high, + 1 = active low. + +Example: + sc16is750: sc16is750@51 { + compatible = "nxp,sc16is750"; + reg = <0x51>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt index 1928a3e83cd..77054772a8f 100644 --- a/Documentation/devicetree/bindings/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/serial/of-serial.txt @@ -37,6 +37,7 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. +- has-hw-flow-control: the hardware has flow control capability. Example: diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 53e6c175db6..64fd7dec1bb 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Must contain one of the following: + - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. - "renesas,scifb-r8a7790" for R8A7790 (R-Car H2) SCIFB compatible UART. diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt new file mode 100644 index 00000000000..4ce24d425bf --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt @@ -0,0 +1,78 @@ +QCOM GSBI (General Serial Bus Interface) Driver + +The GSBI controller is modeled as a node with zero or more child nodes, each +representing a serial sub-node device that is mux'd as part of the GSBI +configuration settings. The mode setting will govern the input/output mode of +the 4 GSBI IOs. + +Required properties: +- compatible: must contain "qcom,gsbi-v1.0.0" for APQ8064/IPQ8064 +- reg: Address range for GSBI registers +- clocks: required clock +- clock-names: must contain "iface" entry +- qcom,mode : indicates MUX value for configuration of the serial interface. + Please reference dt-bindings/soc/qcom,gsbi.h for valid mux values. + +Optional properties: +- qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference + dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values. + +Required properties if child node exists: +- #address-cells: Must be 1 +- #size-cells: Must be 1 +- ranges: Must be present + +Properties for children: + +A GSBI controller node can contain 0 or more child nodes representing serial +devices. These serial devices can be a QCOM UART, I2C controller, spi +controller, or some combination of aforementioned devices. + +See the following for child node definitions: +Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt +Documentation/devicetree/bindings/spi/qcom,spi-qup.txt +Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt + +Example for APQ8064: + +#include <dt-bindings/soc/qcom,gsbi.h> + + gsbi4@16300000 { + compatible = "qcom,gsbi-v1.0.0"; + reg = <0x16300000 0x100>; + clocks = <&gcc GSBI4_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + qcom,mode = <GSBI_PROT_I2C_UART>; + qcom,crci = <GSBI_CRCI_QUP>; + + /* child nodes go under here */ + + i2c_qup4: i2c@16380000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x16380000 0x1000>; + interrupts = <0 153 0>; + + clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; + + clock-frequency = <200000>; + + #address-cells = <1>; + #size-cells = <0>; + + }; + + uart4: serial@16340000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x16340000 0x1000>, + <0x16300000 0x1000>; + interrupts = <0 152 0x0>; + clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; + status = "ok"; + }; + }; + diff --git a/Documentation/devicetree/bindings/sound/ak4104.txt b/Documentation/devicetree/bindings/sound/ak4104.txt index b902ee39cf8..deca5e18f30 100644 --- a/Documentation/devicetree/bindings/sound/ak4104.txt +++ b/Documentation/devicetree/bindings/sound/ak4104.txt @@ -8,6 +8,8 @@ Required properties: - reg : The chip select number on the SPI bus + - vdd-supply : A regulator node, providing 2.7V - 3.6V + Optional properties: - reset-gpio : a GPIO spec for the reset pin. If specified, it will be @@ -19,4 +21,5 @@ spdif: ak4104@0 { compatible = "asahi-kasei,ak4104"; reg = <0>; spi-max-frequency = <5000000>; + vdd-supply = <&vdd_3v3_reg>; }; diff --git a/Documentation/devicetree/bindings/sound/alc5623.txt b/Documentation/devicetree/bindings/sound/alc5623.txt new file mode 100644 index 00000000000..26c86c98d67 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/alc5623.txt @@ -0,0 +1,25 @@ +ALC5621/ALC5622/ALC5623 audio Codec + +Required properties: + + - compatible: "realtek,alc5623" + - reg: the I2C address of the device. + +Optional properties: + + - add-ctrl: Default register value for Reg-40h, Additional Control + Register. If absent or has the value of 0, the + register is untouched. + + - jack-det-ctrl: Default register value for Reg-5Ah, Jack Detect + Control Register. If absent or has value 0, the + register is untouched. + +Example: + + alc5621: alc5621@1a { + compatible = "alc5621"; + reg = <0x1a>; + add-ctrl = <0x3700>; + jack-det-ctrl = <0x4810>; + }; diff --git a/Documentation/devicetree/bindings/sound/cs42l56.txt b/Documentation/devicetree/bindings/sound/cs42l56.txt new file mode 100644 index 00000000000..4feb0eb27ea --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l56.txt @@ -0,0 +1,63 @@ +CS42L52 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l56" + + - reg : the I2C address of the device for I2C + + - VA-supply, VCP-supply, VLDO-supply : power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - cirrus,gpio-nreset : GPIO controller's phandle and the number + of the GPIO used to reset the codec. + + - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency. + Allowable values of 0x00 through 0x0F. These are raw values written to the + register, not the actual frequency. The frequency is determined by the following. + Frequency = MCLK / 4 * (N+2) + N = chgfreq_val + MCLK = Where MCLK is the frequency of the mclk signal after the MCLKDIV2 circuit. + + - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured + as a pseudo-differential input referenced to AIN1REF/AIN3A. + + - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured + as a pseudo-differential input referenced to AIN2REF/AIN3B. + + - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin. + 0 = 0.5 x VA + 1 = 0.6 x VA + 2 = 0.7 x VA + 3 = 0.8 x VA + 4 = 0.83 x VA + 5 = 0.91 x VA + + - cirrus,adaptive-pwr-cfg : Configures how the power to the Headphone and Lineout + Amplifiers adapt to the output signal levels. + 0 = Adapt to Volume Mode. Voltage level determined by the sum of the relevant volume settings. + 1 = Fixed - Headphone and Line Amp supply = + or - VCP/2. + 2 = Fixed - Headphone and Line Amp supply = + or - VCP. + 3 = Adapted to Signal; Voltage level is dynamically determined by the output signal. + + - cirrus,hpf-left-freq, hpf-right-freq : Sets the corner frequency (-3dB point) for the internal High-Pass + Filter. + 0 = 1.8Hz + 1 = 119Hz + 2 = 236Hz + 3 = 464Hz + + +Example: + +codec: codec@4b { + compatible = "cirrus,cs42l56"; + reg = <0x4b>; + gpio-reset = <&gpio 10 0>; + cirrus,chgfreq-divisor = <0x05>; + cirrus.ain1_ref_cfg; + cirrus,micbias-lvl = <5>; + VA-supply = <®_audio>; +}; diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 98611a6761c..0f4e2382819 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -7,10 +7,11 @@ codec/DSP interfaces. Required properties: -- compatible: Compatible list, contains "fsl,vf610-sai". +- compatible: Compatible list, contains "fsl,vf610-sai" or "fsl,imx6sx-sai". - reg: Offset and length of the register set for the device. - clocks: Must contain an entry for each entry in clock-names. -- clock-names : Must include the "sai" entry. +- clock-names : Must include the "bus" for register access and "mclk1" "mclk2" + "mclk3" for bit clock and frame clock providing. - dmas : Generic dma devicetree binding as described in Documentation/devicetree/bindings/dma/dma.txt. - dma-names : Two dmas have to be defined, "tx" and "rx". @@ -30,8 +31,10 @@ sai2: sai@40031000 { reg = <0x40031000 0x1000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sai2_1>; - clocks = <&clks VF610_CLK_SAI2>; - clock-names = "sai"; + clocks = <&clks VF610_CLK_PLATFORM_BUS>, + <&clks VF610_CLK_SAI2>, + <&clks 0>, <&clks 0>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 0 VF610_EDMA_MUXID0_SAI2_TX>, <&edma0 0 VF610_EDMA_MUXID0_SAI2_RX>; diff --git a/Documentation/devicetree/bindings/sound/max98090.txt b/Documentation/devicetree/bindings/sound/max98090.txt index e4c8b36dcf8..a5e63fa47dc 100644 --- a/Documentation/devicetree/bindings/sound/max98090.txt +++ b/Documentation/devicetree/bindings/sound/max98090.txt @@ -10,6 +10,12 @@ Required properties: - interrupts : The CODEC's interrupt output. +Optional properties: + +- clocks: The phandle of the master clock to the CODEC + +- clock-names: Should be "mclk" + Pins on the device (for linking into audio routes): * MIC1 diff --git a/Documentation/devicetree/bindings/sound/max98095.txt b/Documentation/devicetree/bindings/sound/max98095.txt new file mode 100644 index 00000000000..318a4c82f17 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98095.txt @@ -0,0 +1,22 @@ +MAX98095 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "maxim,max98095". + +- reg : The I2C address of the device. + +Optional properties: + +- clocks: The phandle of the master clock to the CODEC + +- clock-names: Should be "mclk" + +Example: + +max98095: codec@11 { + compatible = "maxim,max98095"; + reg = <0x11>; +}; diff --git a/Documentation/devicetree/bindings/sound/nokia,rx51.txt b/Documentation/devicetree/bindings/sound/nokia,rx51.txt new file mode 100644 index 00000000000..72f93d99627 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nokia,rx51.txt @@ -0,0 +1,27 @@ +* Nokia N900 audio setup + +Required properties: +- compatible: Should contain "nokia,n900-audio" +- nokia,cpu-dai: phandle for the McBSP node +- nokia,audio-codec: phandles for the main TLV320AIC3X node and the + auxiliary TLV320AIC3X node (in this order) +- nokia,headphone-amplifier: phandle for the TPA6130A2 node +- tvout-selection-gpios: GPIO for tvout selection +- jack-detection-gpios: GPIO for jack detection +- eci-switch-gpios: GPIO for ECI (Enhancement Control Interface) switch +- speaker-amplifier-gpios: GPIO for speaker amplifier + +Example: + +sound { + compatible = "nokia,n900-audio"; + + nokia,cpu-dai = <&mcbsp2>; + nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>; + nokia,headphone-amplifier = <&tpa6130a2>; + + tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */ + jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */ + eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */ + speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt new file mode 100644 index 00000000000..b4730c2822b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt @@ -0,0 +1,28 @@ +NVIDIA Tegra30 HDA controller + +Required properties: +- compatible : "nvidia,tegra30-hda" +- reg : Should contain the HDA registers location and length. +- interrupts : The interrupt from the HDA controller. +- clocks : Must contain an entry for each required entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi + +Example: + +hda@0,70030000 { + compatible = "nvidia,tegra124-hda", "nvidia,tegra30-hda"; + reg = <0x0 0x70030000 0x0 0x10000>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_HDA>, + <&tegra_car TEGRA124_CLK_HDA2HDMI>, + <&tegra_car TEGRA124_CLK_HDA2CODEC_2X>; + clock-names = "hda", "hda2hdmi", "hda2codec_2x"; + resets = <&tegra_car 125>, /* hda */ + <&tegra_car 128>; /* hda2hdmi */ + <&tegra_car 111>, /* hda2codec_2x */ + reset-names = "hda", "hda2hdmi", "hda2codec_2x"; +}; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index a44e9179faf..8346cab046c 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -20,6 +20,7 @@ Required properties: SSI subnode properties: - interrupts : Should contain SSI interrupt for PIO transfer - shared-pin : if shared clock pin +- pio-transfer : use PIO transfer mode SRC subnode properties: no properties at this point diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt index 068a1141b06..bac4d9ac1ed 100644 --- a/Documentation/devicetree/bindings/sound/rt5640.txt +++ b/Documentation/devicetree/bindings/sound/rt5640.txt @@ -1,10 +1,10 @@ -RT5640 audio CODEC +RT5640/RT5639 audio CODEC This device supports I2C only. Required properties: -- compatible : "realtek,rt5640". +- compatible : One of "realtek,rt5640" or "realtek,rt5639". - reg : The I2C address of the device. @@ -18,7 +18,7 @@ Optional properties: - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. -Pins on the device (for linking into audio routes): +Pins on the device (for linking into audio routes) for RT5639/RT5640: * DMIC1 * DMIC2 @@ -31,13 +31,16 @@ Pins on the device (for linking into audio routes): * HPOR * LOUTL * LOUTR - * MONOP - * MONON * SPOLP * SPOLN * SPORP * SPORN +Additional pins on the device for RT5640: + + * MONOP + * MONON + Example: rt5640 { diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index 131aa2ad7f1..c2e9841dfce 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -1,6 +1,6 @@ Simple-Card: -Simple-Card specifies audio DAI connection of SoC <-> codec. +Simple-Card specifies audio DAI connections of SoC <-> codec. Required properties: @@ -10,26 +10,54 @@ Optional properties: - simple-audio-card,name : User specified audio sound card name, one string property. -- simple-audio-card,format : CPU/CODEC common audio format. - "i2s", "right_j", "left_j" , "dsp_a" - "dsp_b", "ac97", "pdm", "msb", "lsb" - simple-audio-card,widgets : Please refer to widgets.txt. - simple-audio-card,routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, the second being the connection's source. -- dai-tdm-slot-num : Please refer to tdm-slot.txt. -- dai-tdm-slot-width : Please refer to tdm-slot.txt. +- simple-audio-card,mclk-fs : Multiplication factor between stream rate and codec + mclk. + +Optional subnodes: + +- simple-audio-card,dai-link : Container for dai-link level + properties and the CPU and CODEC + sub-nodes. This container may be + omitted when the card has only one + DAI link. See the examples and the + section bellow. + +Dai-link subnode properties and subnodes: + +If dai-link subnode is omitted and the subnode properties are directly +under "sound"-node the subnode property and subnode names have to be +prefixed with "simple-audio-card,"-prefix. -Required subnodes: +Required dai-link subnodes: -- simple-audio-card,dai-link : container for the CPU and CODEC sub-nodes - This container may be omitted when the - card has only one DAI link. - See the examples. +- cpu : CPU sub-node +- codec : CODEC sub-node -- simple-audio-card,cpu : CPU sub-node -- simple-audio-card,codec : CODEC sub-node +Optional dai-link subnode properties: + +- format : CPU/CODEC common audio format. + "i2s", "right_j", "left_j" , "dsp_a" + "dsp_b", "ac97", "pdm", "msb", "lsb" +- frame-master : Indicates dai-link frame master. + phandle to a cpu or codec subnode. +- bitclock-master : Indicates dai-link bit clock master. + phandle to a cpu or codec subnode. +- bitclock-inversion : bool property. Add this if the + dai-link uses bit clock inversion. +- frame-inversion : bool property. Add this if the + dai-link uses frame clock inversion. + +For backward compatibility the frame-master and bitclock-master +properties can be used as booleans in codec subnode to indicate if the +codec is the dai-link frame or bit clock master. In this case there +should be no dai-link node, the same properties should not be present +at sound-node level, and the bitclock-inversion and frame-inversion +properties should also be placed in the codec node if needed. Required CPU/CODEC subnodes properties: @@ -37,29 +65,21 @@ Required CPU/CODEC subnodes properties: Optional CPU/CODEC subnodes properties: -- format : CPU/CODEC specific audio format if needed. - see simple-audio-card,format -- frame-master : bool property. add this if subnode is frame master -- bitclock-master : bool property. add this if subnode is bitclock master -- bitclock-inversion : bool property. add this if subnode has clock inversion -- frame-inversion : bool property. add this if subnode has frame inversion +- dai-tdm-slot-num : Please refer to tdm-slot.txt. +- dai-tdm-slot-width : Please refer to tdm-slot.txt. - clocks / system-clock-frequency : specify subnode's clock if needed. it can be specified via "clocks" if system has clock node (= common clock), or "system-clock-frequency" (if system doens't support common clock) -Note: - * For 'format', 'frame-master', 'bitclock-master', 'bitclock-inversion' and - 'frame-inversion', the simple card will use the settings of CODEC for both - CPU and CODEC sides as we need to keep the settings identical for both ends - of the link. - Example 1 - single DAI link: sound { compatible = "simple-audio-card"; simple-audio-card,name = "VF610-Tower-Sound-Card"; simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&dailink0_master>; + simple-audio-card,frame-master = <&dailink0_master>; simple-audio-card,widgets = "Microphone", "Microphone Jack", "Headphone", "Headphone Jack", @@ -69,17 +89,12 @@ sound { "Headphone Jack", "HP_OUT", "External Speaker", "LINE_OUT"; - dai-tdm-slot-num = <2>; - dai-tdm-slot-width = <8>; - simple-audio-card,cpu { sound-dai = <&sh_fsi2 0>; }; - simple-audio-card,codec { + dailink0_master: simple-audio-card,codec { sound-dai = <&ak4648>; - bitclock-master; - frame-master; clocks = <&osc>; }; }; @@ -105,31 +120,31 @@ Example 2 - many DAI links: sound { compatible = "simple-audio-card"; simple-audio-card,name = "Cubox Audio"; - simple-audio-card,format = "i2s"; simple-audio-card,dai-link@0 { /* I2S - HDMI */ - simple-audio-card,cpu { + format = "i2s"; + cpu { sound-dai = <&audio1 0>; }; - simple-audio-card,codec { + codec { sound-dai = <&tda998x 0>; }; }; simple-audio-card,dai-link@1 { /* S/PDIF - HDMI */ - simple-audio-card,cpu { + cpu { sound-dai = <&audio1 1>; }; - simple-audio-card,codec { + codec { sound-dai = <&tda998x 1>; }; }; simple-audio-card,dai-link@2 { /* S/PDIF - S/PDIF */ - simple-audio-card,cpu { + cpu { sound-dai = <&audio1 1>; }; - simple-audio-card,codec { + codec { sound-dai = <&spdif_codec>; }; }; diff --git a/Documentation/devicetree/bindings/sound/snow.txt b/Documentation/devicetree/bindings/sound/snow.txt new file mode 100644 index 00000000000..678b191c37b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/snow.txt @@ -0,0 +1,17 @@ +Audio Binding for Snow boards + +Required properties: +- compatible : Can be one of the following, + "google,snow-audio-max98090" or + "google,snow-audio-max98095" +- samsung,i2s-controller: The phandle of the Samsung I2S controller +- samsung,audio-codec: The phandle of the audio codec + +Example: + +sound { + compatible = "google,snow-audio-max98095"; + + samsung,i2s-controller = <&i2s0>; + samsung,audio-codec = <&max98095>; +}; diff --git a/Documentation/devicetree/bindings/sound/st,sta350.txt b/Documentation/devicetree/bindings/sound/st,sta350.txt new file mode 100644 index 00000000000..b7e71bf5caf --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sta350.txt @@ -0,0 +1,131 @@ +STA350 audio CODEC + +The driver for this device only supports I2C. + +Required properties: + + - compatible: "st,sta350" + - reg: the I2C address of the device for I2C + - reset-gpios: a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - power-down-gpios: a GPIO spec for the power down pin. If specified, + it will be deasserted before communication to the codec + starts. + + - vdd-dig-supply: regulator spec, providing 3.3V + - vdd-pll-supply: regulator spec, providing 3.3V + - vcc-supply: regulator spec, providing 5V - 26V + +Optional properties: + + - st,output-conf: number, Selects the output configuration: + 0: 2-channel (full-bridge) power, 2-channel data-out + 1: 2 (half-bridge). 1 (full-bridge) on-board power + 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX + 3: 1 Channel Mono-Parallel + If parameter is missing, mode 0 will be enabled. + This property has to be specified as '/bits/ 8' value. + + - st,ch1-output-mapping: Channel 1 output mapping + - st,ch2-output-mapping: Channel 2 output mapping + - st,ch3-output-mapping: Channel 3 output mapping + 0: Channel 1 + 1: Channel 2 + 2: Channel 3 + If parameter is missing, channel 1 is choosen. + This properties have to be specified as '/bits/ 8' values. + + - st,thermal-warning-recover: + If present, thermal warning recovery is enabled. + + - st,thermal-warning-adjustment: + If present, thermal warning adjustment is enabled. + + - st,fault-detect-recovery: + If present, then fault recovery will be enabled. + + - st,ffx-power-output-mode: string + The FFX power output mode selects how the FFX output timing is + configured. Must be one of these values: + - "drop-compensation" + - "tapered-compensation" + - "full-power-mode" + - "variable-drop-compensation" (default) + + - st,drop-compensation-ns: number + Only required for "st,ffx-power-output-mode" == + "variable-drop-compensation". + Specifies the drop compensation in nanoseconds. + The value must be in the range of 0..300, and only + multiples of 20 are allowed. Default is 140ns. + + - st,overcurrent-warning-adjustment: + If present, overcurrent warning adjustment is enabled. + + - st,max-power-use-mpcc: + If present, then MPCC bits are used for MPC coefficients, + otherwise standard MPC coefficients are used. + + - st,max-power-corr: + If present, power bridge correction for THD reduction near maximum + power output is enabled. + + - st,am-reduction-mode: + If present, FFX mode runs in AM reduction mode, otherwise normal + FFX mode is used. + + - st,odd-pwm-speed-mode: + If present, PWM speed mode run on odd speed mode (341.3 kHz) on all + channels. If not present, normal PWM spped mode (384 kHz) will be used. + + - st,distortion-compensation: + If present, distortion compensation variable uses DCC coefficient. + If not present, preset DC coefficient is used. + + - st,invalid-input-detect-mute: + If present, automatic invalid input detect mute is enabled. + + - st,activate-mute-output: + If present, a mute output will be activated in ase the volume will + reach a value lower than -76 dBFS. + + - st,bridge-immediate-off: + If present, the bridge will be switched off immediately after the + power-down-gpio goes low. Otherwise, the bridge will wait for 13 + million clock cycles to pass before shutting down. + + - st,noise-shape-dc-cut: + If present, the noise-shaping technique on the DC cutoff filter are + enabled. + + - st,powerdown-master-volume: + If present, the power-down pin and I2C power-down functions will + act on the master volume. Otherwise, the functions will act on the + mute commands. + + - st,powerdown-delay-divider: + If present, the bridge power-down time will be divided by the provided + value. If not specified, a divider of 1 will be used. Allowed values + are 1, 2, 4, 8, 16, 32, 64 and 128. + This property has to be specified as '/bits/ 8' value. + +Example: + +codec: sta350@38 { + compatible = "st,sta350"; + reg = <0x1c>; + reset-gpios = <&gpio1 19 0>; + power-down-gpios = <&gpio1 16 0>; + st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel + // (full-bridge) power, + // 2-channel data-out + st,ch1-output-mapping = /bits/ 8 <0>; // set channel 1 output ch 1 + st,ch2-output-mapping = /bits/ 8 <0>; // set channel 2 output ch 1 + st,ch3-output-mapping = /bits/ 8 <0>; // set channel 3 output ch 1 + st,max-power-correction; // enables power bridge + // correction for THD reduction + // near maximum power output + st,invalid-input-detect-mute; // mute if no valid digital + // audio signal is provided. +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt index b032dd76e9d..a2331372068 100644 --- a/Documentation/devicetree/bindings/spi/fsl-spi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -42,6 +42,10 @@ Required properties: - interrupts : should contain eSPI interrupt, the device has one interrupt. - fsl,espi-num-chipselects : the number of the chipselect signals. +Optional properties: +- fsl,csbef: chip select assertion time in bits before frame starts +- fsl,csaft: chip select negation time in bits after frame ends + Example: spi@110000 { #address-cells = <1>; @@ -51,4 +55,6 @@ Example: interrupts = <53 0x2>; interrupt-parent = <&mpic>; fsl,espi-num-chipselects = <4>; + fsl,csbef = <1>; + fsl,csaft = <1>; }; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index e5a4d1b4acf..bbaa857dd68 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -55,13 +55,15 @@ contain the following properties. chip select active high - spi-3wire - (optional) Empty property indicating device requires 3-wire mode. +- spi-lsb-first - (optional) Empty property indicating device requires + LSB first mode. - spi-tx-bus-width - (optional) The bus width(number of data wires) that used for MOSI. Defaults to 1 if not present. - spi-rx-bus-width - (optional) The bus width(number of data wires) that used for MISO. Defaults to 1 if not present. Some SPI controllers and devices support Dual and Quad SPI transfer mode. -It allows data in SPI system transfered in 2 wires(DUAL) or 4 wires(QUAD). +It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD). Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is only 1(SINGLE), 2(DUAL) and 4(QUAD). Dual/Quad mode is not allowed when 3-wire mode is used. diff --git a/Documentation/devicetree/bindings/spi/spi-cadence.txt b/Documentation/devicetree/bindings/spi/spi-cadence.txt new file mode 100644 index 00000000000..94f09141a4f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-cadence.txt @@ -0,0 +1,31 @@ +Cadence SPI controller Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Should be "cdns,spi-r1p6" or "xlnx,zynq-spi-r1p6". +- reg : Physical base address and size of SPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller +- clock-names : List of input clock names - "ref_clk", "pclk" + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). + +Optional properties: +- num-cs : Number of chip selects used. + If a decoder is used, this will be the number of + chip selects after the decoder. +- is-decoded-cs : Flag to indicate whether decoder is used or not. + +Example: + + spi@e0007000 { + compatible = "xlnx,zynq-spi-r1p6"; + clock-names = "ref_clk", "pclk"; + clocks = <&clkc 26>, <&clkc 35>; + interrupt-parent = <&intc>; + interrupts = <0 49 4>; + num-cs = <4>; + is-decoded-cs = <0>; + reg = <0xe0007000 0x1000>; + } ; diff --git a/Documentation/devicetree/bindings/spi/spi-dw.txt b/Documentation/devicetree/bindings/spi/spi-dw.txt new file mode 100644 index 00000000000..7b63ed60199 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-dw.txt @@ -0,0 +1,24 @@ +Synopsys DesignWare SPI master + +Required properties: +- compatible: should be "snps,designware-spi" +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- reg: address and length of the spi master registers +- interrupts: should contain one interrupt +- clocks: spi clock phandle +- num-cs: see spi-bus.txt + +Optional properties: +- cs-gpios: see spi-bus.txt + +Example: + +spi: spi@4020a000 { + compatible = "snps,designware-spi"; + interrupts = <11 1>; + reg = <0x4020a000 0x1000>; + clocks = <&pclk>; + num-cs = <2>; + cs-gpios = <&banka 0 0>; +}; diff --git a/Documentation/devicetree/bindings/spmi/spmi.txt b/Documentation/devicetree/bindings/spmi/spmi.txt index 462a42fb3a1..4bb10d161a2 100644 --- a/Documentation/devicetree/bindings/spmi/spmi.txt +++ b/Documentation/devicetree/bindings/spmi/spmi.txt @@ -26,7 +26,7 @@ Each child node must have one and only one 'reg' entry of type SPMI_USID. reg = <...>; #address-cells = <2>; - #size-cells <0>; + #size-cells = <0>; child@0 { compatible = "..."; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt index 3be5ce7a965..e75f0e549ff 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt @@ -61,6 +61,7 @@ Required properties: Optional properties: - interface_pix_fmt: How this display is connected to the display interface. Currently supported types: "rgb24", "rgb565", "bgr666" + and "lvds666". - edid: verbatim EDID data block describing attached display. - ddc: phandle describing the i2c bus handling the display data channel diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt index 7c26154b8bb..27cfc7d7ccd 100644 --- a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt +++ b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt @@ -9,6 +9,9 @@ Required properties: one) - clocks: phandle to the source clock (usually the AHB clock) +Optionnal properties: +- resets: phandle to a reset controller asserting the timer + Example: timer@01c60000 { @@ -19,4 +22,5 @@ timer@01c60000 { <0 53 1>, <0 54 1>; clocks = <&ahb1_gates 19>; + resets = <&ahb1rst 19>; }; diff --git a/Documentation/devicetree/bindings/timer/efm32,timer.txt b/Documentation/devicetree/bindings/timer/energymicro,efm32-timer.txt index 97a568f696c..e502c11b221 100644 --- a/Documentation/devicetree/bindings/timer/efm32,timer.txt +++ b/Documentation/devicetree/bindings/timer/energymicro,efm32-timer.txt @@ -6,7 +6,7 @@ channels and can be used as PWM or Quadrature Decoder. Available clock sources are the cpu's HFPERCLK (with a 10-bit prescaler) or an external pin. Required properties: -- compatible : Should be efm32,timer +- compatible : Should be "energymicro,efm32-timer" - reg : Address and length of the register set - clocks : Should contain a reference to the HFPERCLK @@ -16,7 +16,7 @@ Optional properties: Example: timer@40010c00 { - compatible = "efm32,timer"; + compatible = "energymicro,efm32-timer"; reg = <0x40010c00 0x400>; interrupts = <14>; clocks = <&cmu clk_HFPERCLKTIMER3>; diff --git a/Documentation/devicetree/bindings/timer/fsl,ftm-timer.txt b/Documentation/devicetree/bindings/timer/fsl,ftm-timer.txt new file mode 100644 index 00000000000..aa8c40230e5 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/fsl,ftm-timer.txt @@ -0,0 +1,31 @@ +Freescale FlexTimer Module (FTM) Timer + +Required properties: + +- compatible : should be "fsl,ftm-timer" +- reg : Specifies base physical address and size of the register sets for the + clock event device and clock source device. +- interrupts : Should be the clock event device interrupt. +- clocks : The clocks provided by the SoC to drive the timer, must contain an + entry for each entry in clock-names. +- clock-names : Must include the following entries: + o "ftm-evt" + o "ftm-src" + o "ftm-evt-counter-en" + o "ftm-src-counter-en" +- big-endian: One boolean property, the big endian mode will be in use if it is + present, or the little endian mode will be in use for all the device registers. + +Example: +ftm: ftm@400b8000 { + compatible = "fsl,ftm-timer"; + reg = <0x400b8000 0x1000 0x400b9000 0x1000>; + interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "ftm-evt", "ftm-src", + "ftm-evt-counter-en", "ftm-src-counter-en"; + clocks = <&clks VF610_CLK_FTM2>, + <&clks VF610_CLK_FTM3>, + <&clks VF610_CLK_FTM2_EXT_FIX_EN>, + <&clks VF610_CLK_FTM3_EXT_FIX_EN>; + big-endian; +}; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt new file mode 100644 index 00000000000..f2899b55093 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt @@ -0,0 +1,17 @@ +Qualcomm CI13xxx (Chipidea) USB controllers + +Required properties: +- compatible: should contain "qcom,ci-hdrc" +- reg: offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the controller interrupt. +- usb-phy: phandle for the PHY device +- dr_mode: Should be "peripheral" + +Examples: + gadget@f9a55000 { + compatible = "qcom,ci-hdrc"; + reg = <0xf9a55000 0x400>; + dr_mode = "peripheral"; + interrupts = <0 134 0>; + usb-phy = <&usbphy0>; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index b8b6871f116..467ddd15d40 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -13,7 +13,7 @@ Refer to clk/clock-bindings.txt for generic clock consumer properties Optional properties: - phys: phy provider specifier -- phy-names: shall be "device" +- phy-names: shall be "usb2-phy" Refer to phy/phy-bindings.txt for generic phy consumer properties Example: diff --git a/Documentation/devicetree/bindings/usb/ehci-orion.txt b/Documentation/devicetree/bindings/usb/ehci-orion.txt index 6bc09ec14c4..17c3bc858b8 100644 --- a/Documentation/devicetree/bindings/usb/ehci-orion.txt +++ b/Documentation/devicetree/bindings/usb/ehci-orion.txt @@ -6,6 +6,11 @@ Required properties: region. - interrupts: The EHCI interrupt +Optional properties: +- clocks: reference to the clock +- phys: reference to the USB PHY +- phy-names: name of the USB PHY, should be "usb" + Example: ehci@50000 { diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index d967ba16de6..a3b5990d0f2 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -12,6 +12,13 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are EHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on EHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings; specifying phy used by port. Optional properties: - samsung,vbus-gpio: if present, specifies the GPIO that @@ -27,6 +34,14 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + status = "disabled"; + }; }; OHCI @@ -38,6 +53,13 @@ Required properties: - interrupts: interrupt number to the cpu. - clocks: from common clock binding: handle to usb clock. - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are OHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on OHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings, specifying phy used by port. Example: usb@12120000 { @@ -47,6 +69,15 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + status = "disabled"; + }; + }; DWC3 diff --git a/Documentation/devicetree/bindings/usb/gr-udc.txt b/Documentation/devicetree/bindings/usb/gr-udc.txt index 0c5118f7a91..e9445224fab 100644 --- a/Documentation/devicetree/bindings/usb/gr-udc.txt +++ b/Documentation/devicetree/bindings/usb/gr-udc.txt @@ -12,17 +12,23 @@ Required properties: - reg : Address and length of the register set for the device -- interrupts : Interrupt numbers for this device +- interrupts : Interrupt numbers for this device. Either one interrupt number + for all interrupts, or one for status related interrupts, one for IN + endpoint related interrupts and one for OUT endpoint related interrupts. Optional properties: -- epobufsizes : An array of buffer sizes for OUT endpoints. If the property is - not present, or for endpoints outside of the array, 1024 is assumed by - the driver. - -- epibufsizes : An array of buffer sizes for IN endpoints. If the property is - not present, or for endpoints outside of the array, 1024 is assumed by - the driver. +- epobufsizes : Array of buffer sizes for OUT endpoints when they differ + from the default size of 1024. The array is indexed by the OUT endpoint + number. If the property is present it typically contains one entry for + each OUT endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. + +- epibufsizes : Array of buffer sizes for IN endpoints when they differ + from the default size of 1024. The array is indexed by the IN endpoint + number. If the property is present it typically contains one entry for + each IN endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. For further information look in the documentation for the GLIB IP core library: http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt index 5ea26c631e3..2826f2af503 100644 --- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -15,3 +15,81 @@ Example EHCI controller device node: usb-phy = <&usb_otg>; }; +USB PHY with optional OTG: + +Required properties: +- compatible: Should contain: + "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY + "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY + +- regs: Offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the OTG interrupt. + +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "phy" USB PHY reference clock + "core" Protocol engine clock + "iface" Interface bus clock + "alt_core" Protocol engine clock for targets with asynchronous + reset methodology. (optional) + +- vdccx-supply: phandle to the regulator for the vdd supply for + digital circuit operation. +- v1p8-supply: phandle to the regulator for the 1.8V supply +- v3p3-supply: phandle to the regulator for the 3.3V supply + +- resets: A list of phandle + reset-specifier pairs for the + resets listed in reset-names +- reset-names: Should contain the following: + "phy" USB PHY controller reset + "link" USB LINK controller reset + +- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of + 1 - PHY control + 2 - PMIC control + +Optional properties: +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device + Mode Eye Diagram test. Start address at which these values will be + written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as + "do not overwrite default value at this address". + For example: qcom,phy-init-sequence = < -1 0x63 >; + Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. + +- qcom,phy-num: Select number of pyco-phy to use, can be one of + 0 - PHY one, default + 1 - Second PHY + Some platforms may have configuration to allow USB + controller work with any of the two HSPHYs present. + +- qcom,vdd-levels: This property must be a list of three integer values + (no, min, max) where each value represents either a voltage + in microvolts or a value corresponding to voltage corner. + +Example HSUSB OTG controller device node: + + usb@f9a55000 { + compatible = "qcom,usb-otg-snps"; + reg = <0xf9a55000 0x400>; + interrupts = <0 134 0>; + dr_mode = "peripheral"; + + clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>, + <&gcc GCC_USB_HS_AHB_CLK>; + + clock-names = "phy", "core", "iface"; + + vddcx-supply = <&pm8841_s2_corner>; + v1p8-supply = <&pm8941_l6>; + v3p3-supply = <&pm8941_l24>; + + resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>; + reset-names = "phy", "link"; + + qcom,otg-control = <1>; + qcom,phy-init-sequence = < -1 0x63 >; + qcom,vdd-levels = <1 5 7>; + }; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 38b2faec419..38d9bb8507c 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -44,7 +44,9 @@ Board specific device node entry }; OMAP DWC3 GLUE - - compatible : Should be "ti,dwc3" + - compatible : Should be + * "ti,dwc3" for OMAP5 and DRA7 + * "ti,am437x-dwc3" for AM437x - ti,hwmods : Should be "usb_otg_ss" - reg : Address and length of the register set for the device. - interrupts : The irq number of this device that is used to interrupt the diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt index ff151ec084c..43c1a4e0676 100644 --- a/Documentation/devicetree/bindings/usb/usb-ehci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -15,6 +15,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" + - resets : phandle + reset specifier pair Example (Sequoia 440EPx): ehci@e0000300 { diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index 45f67d91e88..b968a1aea99 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -12,6 +12,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" +- resets : phandle + reset specifier pair Example: diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 90f8f607d12..5a79377c6a9 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -1,11 +1,17 @@ USB xHCI controllers Required properties: - - compatible: should be "generic-xhci" (deprecated: "xhci-platform"). + - compatible: should be one of "generic-xhci", + "marvell,armada-375-xhci", "marvell,armada-380-xhci", + "renesas,xhci-r8a7790", "renesas,xhci-r8a7791" (deprecated: + "xhci-platform"). - reg: should contain address and length of the standard XHCI register set for the device. - interrupts: one XHCI interrupt should be described here. +Optional property: + - clocks: reference to a clock + Example: usb@f0931000 { compatible = "generic-xhci"; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index a018da4a7ad..221ac0dbc67 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -15,6 +15,14 @@ Optional properties: - reset-gpios: Should specify GPIO for reset. - initial-mode: Should specify initial mode. (1 for HUB mode, 2 for STANDBY mode) +- refclk: Clock used for driving REFCLK signal (optional, if not provided + the driver assumes that clock signal is always available, its + rate is specified by REF_SEL pins and a value from the primary + reference clock frequencies table is used) +- refclk-frequency: Frequency of the REFCLK signal as defined by REF_SEL + pins (optional, if not provided, driver will not set rate of the + REFCLK signal and assume that a value from the primary reference + clock frequencies table is used) Examples: usb3503@08 { diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index abc308083ac..5261271046c 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -13,6 +13,7 @@ allwinner Allwinner Technology Co., Ltd. altr Altera Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amd Advanced Micro Devices (AMD), Inc. +ams AMS AG amstaos AMS-Taos Inc. apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. @@ -73,12 +74,15 @@ lantiq Lantiq Semiconductor lg LG Corporation linux Linux-specific binding lsi LSI Corp. (LSI Logic) +lltc Linear Technology Corporation marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products +micrel Micrel Inc. microchip Microchip Technology Inc. mosaixtech Mosaix Technologies, Inc. moxa Moxa mpl MPL AG +mundoreader Mundo Reader S.L. mxicy Macronix International Co., Ltd. national National Semiconductor neonode Neonode Inc. @@ -98,6 +102,7 @@ powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc qnap QNAP Systems, Inc. +radxa Radxa raidsonic RaidSonic Technology GmbH ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International @@ -123,10 +128,12 @@ stericsson ST-Ericsson synology Synology, Inc. ti Texas Instruments tlm Trusted Logic Mobility +toradex Toradex AG toshiba Toshiba Corporation toumaz Toumaz usi Universal Scientifc Industrial Co., Ltd. v3 V3 Semiconductor +variscite Variscite Ltd. via VIA Technologies, Inc. voipac Voipac Technologies s.r.o. winbond Winbond Electronics corp. diff --git a/Documentation/devicetree/bindings/video/hdmi-connector.txt b/Documentation/devicetree/bindings/video/hdmi-connector.txt index ccccc19e257..acd5668b1ce 100644 --- a/Documentation/devicetree/bindings/video/hdmi-connector.txt +++ b/Documentation/devicetree/bindings/video/hdmi-connector.txt @@ -7,6 +7,7 @@ Required properties: Optional properties: - label: a symbolic name for the connector +- hpd-gpios: HPD GPIO number Required nodes: - Video port for HDMI input diff --git a/Documentation/devicetree/bindings/video/lgphilips,lb035q02.txt b/Documentation/devicetree/bindings/video/lgphilips,lb035q02.txt new file mode 100644 index 00000000000..1a1e653e540 --- /dev/null +++ b/Documentation/devicetree/bindings/video/lgphilips,lb035q02.txt @@ -0,0 +1,33 @@ +LG.Philips LB035Q02 Panel +========================= + +Required properties: +- compatible: "lgphilips,lb035q02" +- enable-gpios: panel enable gpio + +Optional properties: +- label: a symbolic name for the panel + +Required nodes: +- Video port for DPI input + +Example +------- + +lcd-panel: panel@0 { + compatible = "lgphilips,lb035q02"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + + enable-gpios = <&gpio7 7 0>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/panel-dpi.txt b/Documentation/devicetree/bindings/video/panel-dpi.txt new file mode 100644 index 00000000000..a40180b05ba --- /dev/null +++ b/Documentation/devicetree/bindings/video/panel-dpi.txt @@ -0,0 +1,45 @@ +Generic MIPI DPI Panel +====================== + +Required properties: +- compatible: "panel-dpi" + +Optional properties: +- label: a symbolic name for the panel +- enable-gpios: panel enable gpio + +Required nodes: +- "panel-timing" containing video timings + (Documentation/devicetree/bindings/video/display-timing.txt) +- Video port for DPI input + +Example +------- + +lcd0: display@0 { + compatible = "samsung,lte430wq-f0c", "panel-dpi"; + label = "lcd"; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + panel-timing { + clock-frequency = <9200000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <8>; + hback-porch = <4>; + hsync-len = <41>; + vback-porch = <2>; + vfront-porch = <4>; + vsync-len = <10>; + + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/video/sharp,ls037v7dw01.txt b/Documentation/devicetree/bindings/video/sharp,ls037v7dw01.txt new file mode 100644 index 00000000000..0cc8981e9d4 --- /dev/null +++ b/Documentation/devicetree/bindings/video/sharp,ls037v7dw01.txt @@ -0,0 +1,43 @@ +SHARP LS037V7DW01 TFT-LCD panel +=================================== + +Required properties: +- compatible: "sharp,ls037v7dw01" + +Optional properties: +- label: a symbolic name for the panel +- enable-gpios: a GPIO spec for the optional enable pin. + This pin is the INI pin as specified in the LS037V7DW01.pdf file. +- reset-gpios: a GPIO spec for the optional reset pin. + This pin is the RESB pin as specified in the LS037V7DW01.pdf file. +- mode-gpios: a GPIO + ordered MO, LR, and UD as specified in the LS037V7DW01.pdf file. + +Required nodes: +- Video port for DPI input + +This panel can have zero to five GPIOs to configure to change configuration +between QVGA and VGA mode and the scan direction. As these pins can be also +configured with external pulls, all the GPIOs are considered optional with holes +in the array. + +Example +------- + +Example when connected to a omap2+ based device: + +lcd0: display { + compatible = "sharp,ls037v7dw01"; + power-supply = <&lcd_3v3>; + enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */ + reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */ + mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */ + &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */ + &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */ + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/video/ti,omap4-dss.txt b/Documentation/devicetree/bindings/video/ti,omap4-dss.txt index f85d6fcfa70..b8c29fbd1fb 100644 --- a/Documentation/devicetree/bindings/video/ti,omap4-dss.txt +++ b/Documentation/devicetree/bindings/video/ti,omap4-dss.txt @@ -109,3 +109,7 @@ Required properties: Optional nodes: - Video port for HDMI output + +HDMI Endpoint optional properties: +- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-, + D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7) diff --git a/Documentation/devicetree/bindings/video/ti,omap5-dss.txt b/Documentation/devicetree/bindings/video/ti,omap5-dss.txt new file mode 100644 index 00000000000..38ffc8fcd81 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ti,omap5-dss.txt @@ -0,0 +1,96 @@ +Texas Instruments OMAP5 Display Subsystem +========================================= + +See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic +description about OMAP Display Subsystem bindings. + +DSS Core +-------- + +Required properties: +- compatible: "ti,omap5-dss" +- reg: address and length of the register space +- ti,hwmods: "dss_core" +- clocks: handle to fclk +- clock-names: "fck" + +Required nodes: +- DISPC + +Optional nodes: +- DSS Submodules: RFBI, DSI, HDMI +- Video port for DPI output + +DPI Endpoint required properties: +- data-lines: number of lines used + + +DISPC +----- + +Required properties: +- compatible: "ti,omap5-dispc" +- reg: address and length of the register space +- ti,hwmods: "dss_dispc" +- interrupts: the DISPC interrupt +- clocks: handle to fclk +- clock-names: "fck" + + +RFBI +---- + +Required properties: +- compatible: "ti,omap5-rfbi" +- reg: address and length of the register space +- ti,hwmods: "dss_rfbi" +- clocks: handles to fclk and iclk +- clock-names: "fck", "ick" + +Optional nodes: +- Video port for RFBI output +- RFBI controlled peripherals + + +DSI +--- + +Required properties: +- compatible: "ti,omap5-dsi" +- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll' +- reg-names: "proto", "phy", "pll" +- interrupts: the DSI interrupt line +- ti,hwmods: "dss_dsi1" or "dss_dsi2" +- vdd-supply: power supply for DSI +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for DSI output +- DSI controlled peripherals + +DSI Endpoint required properties: +- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-, + DATA1+, DATA1-, ... + + +HDMI +---- + +Required properties: +- compatible: "ti,omap5-hdmi" +- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy', + 'core' +- reg-names: "wp", "pll", "phy", "core" +- interrupts: the HDMI interrupt line +- ti,hwmods: "dss_hdmi" +- vdda-supply: vdda power supply +- clocks: handles to fclk and pll clock +- clock-names: "fck", "sys_clk" + +Optional nodes: +- Video port for HDMI output + +HDMI Endpoint optional properties: +- lanes: list of 8 pin numbers for the HDMI lanes: CLK+, CLK-, D0+, D0-, + D1+, D1-, D2+, D2-. (default: 0,1,2,3,4,5,6,7) diff --git a/Documentation/devicetree/bindings/video/toppoly,td028ttec1.txt b/Documentation/devicetree/bindings/video/toppoly,td028ttec1.txt new file mode 100644 index 00000000000..7175dc3740a --- /dev/null +++ b/Documentation/devicetree/bindings/video/toppoly,td028ttec1.txt @@ -0,0 +1,30 @@ +Toppoly TD028TTEC1 Panel +======================== + +Required properties: +- compatible: "toppoly,td028ttec1" + +Optional properties: +- label: a symbolic name for the panel + +Required nodes: +- Video port for DPI input + +Example +------- + +lcd-panel: td028ttec1@0 { + compatible = "toppoly,td028ttec1"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; + diff --git a/Documentation/devicetree/bindings/video/tpo,td043mtea1.txt b/Documentation/devicetree/bindings/video/tpo,td043mtea1.txt new file mode 100644 index 00000000000..ec6d6297516 --- /dev/null +++ b/Documentation/devicetree/bindings/video/tpo,td043mtea1.txt @@ -0,0 +1,33 @@ +TPO TD043MTEA1 Panel +==================== + +Required properties: +- compatible: "tpo,td043mtea1" +- reset-gpios: panel reset gpio + +Optional properties: +- label: a symbolic name for the panel + +Required nodes: +- Video port for DPI input + +Example +------- + +lcd-panel: panel@0 { + compatible = "tpo,td043mtea1"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + + reset-gpios = <&gpio7 7 0>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; |