diff options
Diffstat (limited to 'Documentation/devicetree')
18 files changed, 308 insertions, 610 deletions
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index f8288ea1b53..6d498c758b4 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -56,3 +56,6 @@ Boards: - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" + +- AM43x EPOS EVM + compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43" diff --git a/Documentation/devicetree/bindings/arm/ste-nomadik.txt b/Documentation/devicetree/bindings/arm/ste-nomadik.txt index 19bca04b81c..6256ec31666 100644 --- a/Documentation/devicetree/bindings/arm/ste-nomadik.txt +++ b/Documentation/devicetree/bindings/arm/ste-nomadik.txt @@ -3,6 +3,11 @@ ST-Ericsson Nomadik Device Tree Bindings For various board the "board" node may contain specific properties that pertain to this particular board, such as board-specific GPIOs. +Required root node property: src +- Nomadik System and reset controller used for basic chip control, clock + and reset line control. +- compatible: must be "stericsson,nomadik,src" + Boards with the Nomadik SoC include: S8815 "MiniKit" manufactured by Calao Systems: diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt new file mode 100644 index 00000000000..cedc2a9c478 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/imx-weim.txt @@ -0,0 +1,49 @@ +Device tree bindings for i.MX Wireless External Interface Module (WEIM) + +The term "wireless" does not imply that the WEIM is literally an interface +without wires. It simply means that this module was originally designed for +wireless and mobile applications that use low-power technology. + +The actual devices are instantiated from the child nodes of a WEIM node. + +Required properties: + + - compatible: Should be set to "fsl,imx6q-weim" + - reg: A resource specifier for the register space + (see the example below) + - clocks: the clock, see the example below. + - #address-cells: Must be set to 2 to allow memory address translation + - #size-cells: Must be set to 1 to allow CS address passing + - ranges: Must be set up to reflect the memory layout with four + integer values for each chip-select line in use: + + <cs-number> 0 <physical address of mapping> <size> + +Timing property for child nodes. It is mandatory, not optional. + + - fsl,weim-cs-timing: The timing array, contains 6 timing values for the + child node. We can get the CS index from the child + node's "reg" property. This property contains the values + for the registers EIM_CSnGCR1, EIM_CSnGCR2, EIM_CSnRCR1, + EIM_CSnRCR2, EIM_CSnWCR1, EIM_CSnWCR2 in this order. + +Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM: + + weim: weim@021b8000 { + compatible = "fsl,imx6q-weim"; + reg = <0x021b8000 0x4000>; + clocks = <&clks 196>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x08000000>; + + nor@0,0 { + compatible = "cfi-flash"; + reg = <0 0 0x02000000>; + #address-cells = <1>; + #size-cells = <1>; + bank-width = <2>; + fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000 + 0x0000c000 0x1404a38e 0x00000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/altr_socfpga.txt b/Documentation/devicetree/bindings/clock/altr_socfpga.txt index bd0c8416a5c..0045433eae1 100644 --- a/Documentation/devicetree/bindings/clock/altr_socfpga.txt +++ b/Documentation/devicetree/bindings/clock/altr_socfpga.txt @@ -9,6 +9,9 @@ Required properties: "altr,socfpga-pll-clock" - for a PLL clock "altr,socfpga-perip-clock" - The peripheral clock divided from the PLL clock. + "altr,socfpga-gate-clk" - Clocks that directly feed peripherals and + can get gated. + - reg : shall be the control register offset from CLOCK_MANAGER's base for the clock. - clocks : shall be the input parent clock phandle for the clock. This is either an oscillator or a pll output. @@ -16,3 +19,7 @@ Required properties: Optional properties: - fixed-divider : If clocks have a fixed divider value, use this property. +- clk-gate : For "socfpga-gate-clk", clk-gate contains the gating register + and the bit index. +- div-reg : For "socfpga-gate-clk", div-reg contains the divider register, bit shift, + and width. diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt index ea5e26f16ae..14d5c2af26f 100644 --- a/Documentation/devicetree/bindings/clock/exynos4-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos4-clock.txt @@ -102,6 +102,7 @@ Exynos4 SoC and this is specified where applicable. sclk_spi0_isp 174 Exynos4x12 sclk_spi1_isp 175 Exynos4x12 sclk_uart_isp 176 Exynos4x12 + sclk_fimg2d 177 [Peripheral Clock Gates] @@ -129,7 +130,7 @@ Exynos4 SoC and this is specified where applicable. smmu_mfcl 274 smmu_mfcr 275 g3d 276 - g2d 277 Exynos4210 + g2d 277 rotator 278 Exynos4210 mdma 279 Exynos4210 smmu_g2d 280 Exynos4210 diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt index d6cb083b90a..0c80c267710 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt @@ -12,253 +12,9 @@ Required properties : - clocks : Should contain phandle and clock specifiers for two clocks: the 32 KHz "32k_in", and the board-specific oscillator "osc". - #clock-cells : Should be 1. - In clock consumers, this cell represents the clock ID exposed by the CAR. - - The first 160 clocks are numbered to match the bits in the CAR's CLK_OUT_ENB - registers. These IDs often match those in the CAR's RST_DEVICES registers, - but not in all cases. Some bits in CLK_OUT_ENB affect multiple clocks. In - this case, those clocks are assigned IDs above 160 in order to highlight - this issue. Implementations that interpret these clock IDs as bit values - within the CLK_OUT_ENB or RST_DEVICES registers should be careful to - explicitly handle these special cases. - - The balance of the clocks controlled by the CAR are assigned IDs of 160 and - above. - - 0 unassigned - 1 unassigned - 2 unassigned - 3 unassigned - 4 rtc - 5 timer - 6 uarta - 7 unassigned (register bit affects uartb and vfir) - 8 unassigned - 9 sdmmc2 - 10 unassigned (register bit affects spdif_in and spdif_out) - 11 i2s1 - 12 i2c1 - 13 ndflash - 14 sdmmc1 - 15 sdmmc4 - 16 unassigned - 17 pwm - 18 i2s2 - 19 epp - 20 unassigned (register bit affects vi and vi_sensor) - 21 2d - 22 usbd - 23 isp - 24 3d - 25 unassigned - 26 disp2 - 27 disp1 - 28 host1x - 29 vcp - 30 i2s0 - 31 unassigned - - 32 unassigned - 33 unassigned - 34 apbdma - 35 unassigned - 36 kbc - 37 unassigned - 38 unassigned - 39 unassigned (register bit affects fuse and fuse_burn) - 40 kfuse - 41 sbc1 - 42 nor - 43 unassigned - 44 sbc2 - 45 unassigned - 46 sbc3 - 47 i2c5 - 48 dsia - 49 unassigned - 50 mipi - 51 hdmi - 52 csi - 53 unassigned - 54 i2c2 - 55 uartc - 56 mipi-cal - 57 emc - 58 usb2 - 59 usb3 - 60 msenc - 61 vde - 62 bsea - 63 bsev - - 64 unassigned - 65 uartd - 66 unassigned - 67 i2c3 - 68 sbc4 - 69 sdmmc3 - 70 unassigned - 71 owr - 72 afi - 73 csite - 74 unassigned - 75 unassigned - 76 la - 77 trace - 78 soc_therm - 79 dtv - 80 ndspeed - 81 i2cslow - 82 dsib - 83 tsec - 84 unassigned - 85 unassigned - 86 unassigned - 87 unassigned - 88 unassigned - 89 xusb_host - 90 unassigned - 91 msenc - 92 csus - 93 unassigned - 94 unassigned - 95 unassigned (bit affects xusb_dev and xusb_dev_src) - - 96 unassigned - 97 unassigned - 98 unassigned - 99 mselect - 100 tsensor - 101 i2s3 - 102 i2s4 - 103 i2c4 - 104 sbc5 - 105 sbc6 - 106 d_audio - 107 apbif - 108 dam0 - 109 dam1 - 110 dam2 - 111 hda2codec_2x - 112 unassigned - 113 audio0_2x - 114 audio1_2x - 115 audio2_2x - 116 audio3_2x - 117 audio4_2x - 118 spdif_2x - 119 actmon - 120 extern1 - 121 extern2 - 122 extern3 - 123 unassigned - 124 unassigned - 125 hda - 126 unassigned - 127 se - - 128 hda2hdmi - 129 unassigned - 130 unassigned - 131 unassigned - 132 unassigned - 133 unassigned - 134 unassigned - 135 unassigned - 136 unassigned - 137 unassigned - 138 unassigned - 139 unassigned - 140 unassigned - 141 unassigned - 142 unassigned - 143 unassigned (bit affects xusb_falcon_src, xusb_fs_src, - xusb_host_src and xusb_ss_src) - 144 cilab - 145 cilcd - 146 cile - 147 dsialp - 148 dsiblp - 149 unassigned - 150 dds - 151 unassigned - 152 dp2 - 153 amx - 154 adx - 155 unassigned (bit affects dfll_ref and dfll_soc) - 156 xusb_ss - - 192 uartb - 193 vfir - 194 spdif_in - 195 spdif_out - 196 vi - 197 vi_sensor - 198 fuse - 199 fuse_burn - 200 clk_32k - 201 clk_m - 202 clk_m_div2 - 203 clk_m_div4 - 204 pll_ref - 205 pll_c - 206 pll_c_out1 - 207 pll_c2 - 208 pll_c3 - 209 pll_m - 210 pll_m_out1 - 211 pll_p - 212 pll_p_out1 - 213 pll_p_out2 - 214 pll_p_out3 - 215 pll_p_out4 - 216 pll_a - 217 pll_a_out0 - 218 pll_d - 219 pll_d_out0 - 220 pll_d2 - 221 pll_d2_out0 - 222 pll_u - 223 pll_u_480M - 224 pll_u_60M - 225 pll_u_48M - 226 pll_u_12M - 227 pll_x - 228 pll_x_out0 - 229 pll_re_vco - 230 pll_re_out - 231 pll_e_out0 - 232 spdif_in_sync - 233 i2s0_sync - 234 i2s1_sync - 235 i2s2_sync - 236 i2s3_sync - 237 i2s4_sync - 238 vimclk_sync - 239 audio0 - 240 audio1 - 241 audio2 - 242 audio3 - 243 audio4 - 244 spdif - 245 clk_out_1 - 246 clk_out_2 - 247 clk_out_3 - 248 blink - 252 xusb_host_src - 253 xusb_falcon_src - 254 xusb_fs_src - 255 xusb_ss_src - 256 xusb_dev_src - 257 xusb_dev - 258 xusb_hs_src - 259 sclk - 260 hclk - 261 pclk - 262 cclk_g - 263 cclk_lp - 264 dfll_ref - 265 dfll_soc + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in header file + <dt-bindings/clock/tegra114-car.h>. Example SoC include file: @@ -270,7 +26,7 @@ Example SoC include file: }; usb@c5004000 { - clocks = <&tegra_car 58>; /* usb2 */ + clocks = <&tegra_car TEGRA114_CLK_USB2>; }; }; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt index e885680f6b4..fcfed5bf73f 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt @@ -12,155 +12,9 @@ Required properties : - clocks : Should contain phandle and clock specifiers for two clocks: the 32 KHz "32k_in", and the board-specific oscillator "osc". - #clock-cells : Should be 1. - In clock consumers, this cell represents the clock ID exposed by the CAR. - - The first 96 clocks are numbered to match the bits in the CAR's CLK_OUT_ENB - registers. These IDs often match those in the CAR's RST_DEVICES registers, - but not in all cases. Some bits in CLK_OUT_ENB affect multiple clocks. In - this case, those clocks are assigned IDs above 95 in order to highlight - this issue. Implementations that interpret these clock IDs as bit values - within the CLK_OUT_ENB or RST_DEVICES registers should be careful to - explicitly handle these special cases. - - The balance of the clocks controlled by the CAR are assigned IDs of 96 and - above. - - 0 cpu - 1 unassigned - 2 unassigned - 3 ac97 - 4 rtc - 5 tmr - 6 uart1 - 7 unassigned (register bit affects uart2 and vfir) - 8 gpio - 9 sdmmc2 - 10 unassigned (register bit affects spdif_in and spdif_out) - 11 i2s1 - 12 i2c1 - 13 ndflash - 14 sdmmc1 - 15 sdmmc4 - 16 twc - 17 pwm - 18 i2s2 - 19 epp - 20 unassigned (register bit affects vi and vi_sensor) - 21 2d - 22 usbd - 23 isp - 24 3d - 25 ide - 26 disp2 - 27 disp1 - 28 host1x - 29 vcp - 30 unassigned - 31 cache2 - - 32 mem - 33 ahbdma - 34 apbdma - 35 unassigned - 36 kbc - 37 stat_mon - 38 pmc - 39 fuse - 40 kfuse - 41 sbc1 - 42 snor - 43 spi1 - 44 sbc2 - 45 xio - 46 sbc3 - 47 dvc - 48 dsi - 49 unassigned (register bit affects tvo and cve) - 50 mipi - 51 hdmi - 52 csi - 53 tvdac - 54 i2c2 - 55 uart3 - 56 unassigned - 57 emc - 58 usb2 - 59 usb3 - 60 mpe - 61 vde - 62 bsea - 63 bsev - - 64 speedo - 65 uart4 - 66 uart5 - 67 i2c3 - 68 sbc4 - 69 sdmmc3 - 70 pcie - 71 owr - 72 afi - 73 csite - 74 unassigned - 75 avpucq - 76 la - 77 unassigned - 78 unassigned - 79 unassigned - 80 unassigned - 81 unassigned - 82 unassigned - 83 unassigned - 84 irama - 85 iramb - 86 iramc - 87 iramd - 88 cram2 - 89 audio_2x a/k/a audio_2x_sync_clk - 90 clk_d - 91 unassigned - 92 sus - 93 cdev2 - 94 cdev1 - 95 unassigned - - 96 uart2 - 97 vfir - 98 spdif_in - 99 spdif_out - 100 vi - 101 vi_sensor - 102 tvo - 103 cve - 104 osc - 105 clk_32k a/k/a clk_s - 106 clk_m - 107 sclk - 108 cclk - 109 hclk - 110 pclk - 111 blink - 112 pll_a - 113 pll_a_out0 - 114 pll_c - 115 pll_c_out1 - 116 pll_d - 117 pll_d_out0 - 118 pll_e - 119 pll_m - 120 pll_m_out1 - 121 pll_p - 122 pll_p_out1 - 123 pll_p_out2 - 124 pll_p_out3 - 125 pll_p_out4 - 126 pll_s - 127 pll_u - 128 pll_x - 129 cop a/k/a avp - 130 audio a/k/a audio_sync_clk - 131 pll_ref - 132 twd + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in header file + <dt-bindings/clock/tegra20-car.h>. Example SoC include file: @@ -172,7 +26,7 @@ Example SoC include file: }; usb@c5004000 { - clocks = <&tegra_car 58>; /* usb2 */ + clocks = <&tegra_car TEGRA20_CLK_USB2>; }; }; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt index f3da3be5fca..0f714081e98 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt @@ -12,212 +12,9 @@ Required properties : - clocks : Should contain phandle and clock specifiers for two clocks: the 32 KHz "32k_in", and the board-specific oscillator "osc". - #clock-cells : Should be 1. - In clock consumers, this cell represents the clock ID exposed by the CAR. - - The first 130 clocks are numbered to match the bits in the CAR's CLK_OUT_ENB - registers. These IDs often match those in the CAR's RST_DEVICES registers, - but not in all cases. Some bits in CLK_OUT_ENB affect multiple clocks. In - this case, those clocks are assigned IDs above 160 in order to highlight - this issue. Implementations that interpret these clock IDs as bit values - within the CLK_OUT_ENB or RST_DEVICES registers should be careful to - explicitly handle these special cases. - - The balance of the clocks controlled by the CAR are assigned IDs of 160 and - above. - - 0 cpu - 1 unassigned - 2 unassigned - 3 unassigned - 4 rtc - 5 timer - 6 uarta - 7 unassigned (register bit affects uartb and vfir) - 8 gpio - 9 sdmmc2 - 10 unassigned (register bit affects spdif_in and spdif_out) - 11 i2s1 - 12 i2c1 - 13 ndflash - 14 sdmmc1 - 15 sdmmc4 - 16 unassigned - 17 pwm - 18 i2s2 - 19 epp - 20 unassigned (register bit affects vi and vi_sensor) - 21 2d - 22 usbd - 23 isp - 24 3d - 25 unassigned - 26 disp2 - 27 disp1 - 28 host1x - 29 vcp - 30 i2s0 - 31 cop_cache - - 32 mc - 33 ahbdma - 34 apbdma - 35 unassigned - 36 kbc - 37 statmon - 38 pmc - 39 unassigned (register bit affects fuse and fuse_burn) - 40 kfuse - 41 sbc1 - 42 nor - 43 unassigned - 44 sbc2 - 45 unassigned - 46 sbc3 - 47 i2c5 - 48 dsia - 49 unassigned (register bit affects cve and tvo) - 50 mipi - 51 hdmi - 52 csi - 53 tvdac - 54 i2c2 - 55 uartc - 56 unassigned - 57 emc - 58 usb2 - 59 usb3 - 60 mpe - 61 vde - 62 bsea - 63 bsev - - 64 speedo - 65 uartd - 66 uarte - 67 i2c3 - 68 sbc4 - 69 sdmmc3 - 70 pcie - 71 owr - 72 afi - 73 csite - 74 pciex - 75 avpucq - 76 la - 77 unassigned - 78 unassigned - 79 dtv - 80 ndspeed - 81 i2cslow - 82 dsib - 83 unassigned - 84 irama - 85 iramb - 86 iramc - 87 iramd - 88 cram2 - 89 unassigned - 90 audio_2x a/k/a audio_2x_sync_clk - 91 unassigned - 92 csus - 93 cdev2 - 94 cdev1 - 95 unassigned - - 96 cpu_g - 97 cpu_lp - 98 3d2 - 99 mselect - 100 tsensor - 101 i2s3 - 102 i2s4 - 103 i2c4 - 104 sbc5 - 105 sbc6 - 106 d_audio - 107 apbif - 108 dam0 - 109 dam1 - 110 dam2 - 111 hda2codec_2x - 112 atomics - 113 audio0_2x - 114 audio1_2x - 115 audio2_2x - 116 audio3_2x - 117 audio4_2x - 118 audio5_2x - 119 actmon - 120 extern1 - 121 extern2 - 122 extern3 - 123 sata_oob - 124 sata - 125 hda - 127 se - 128 hda2hdmi - 129 sata_cold - - 160 uartb - 161 vfir - 162 spdif_in - 163 spdif_out - 164 vi - 165 vi_sensor - 166 fuse - 167 fuse_burn - 168 cve - 169 tvo - - 170 clk_32k - 171 clk_m - 172 clk_m_div2 - 173 clk_m_div4 - 174 pll_ref - 175 pll_c - 176 pll_c_out1 - 177 pll_m - 178 pll_m_out1 - 179 pll_p - 180 pll_p_out1 - 181 pll_p_out2 - 182 pll_p_out3 - 183 pll_p_out4 - 184 pll_a - 185 pll_a_out0 - 186 pll_d - 187 pll_d_out0 - 188 pll_d2 - 189 pll_d2_out0 - 190 pll_u - 191 pll_x - 192 pll_x_out0 - 193 pll_e - 194 spdif_in_sync - 195 i2s0_sync - 196 i2s1_sync - 197 i2s2_sync - 198 i2s3_sync - 199 i2s4_sync - 200 vimclk - 201 audio0 - 202 audio1 - 203 audio2 - 204 audio3 - 205 audio4 - 206 audio5 - 207 clk_out_1 (extern1) - 208 clk_out_2 (extern2) - 209 clk_out_3 (extern3) - 210 sclk - 211 blink - 212 cclk_g - 213 cclk_lp - 214 twd - 215 cml0 - 216 cml1 - 217 hclk - 218 pclk + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in header file + <dt-bindings/clock/tegra30-car.h>. Example SoC include file: @@ -229,7 +26,7 @@ Example SoC include file: }; usb@c5004000 { - clocks = <&tegra_car 58>; /* usb2 */ + clocks = <&tegra_car TEGRA30_CLK_USB2>; }; }; diff --git a/Documentation/devicetree/bindings/clock/st,nomadik.txt b/Documentation/devicetree/bindings/clock/st,nomadik.txt new file mode 100644 index 00000000000..7fc09773de4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,nomadik.txt @@ -0,0 +1,104 @@ +ST Microelectronics Nomadik SRC System Reset and Control + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The Nomadik SRC controller is responsible of controlling chrystals, +PLLs and clock gates. + +Required properties for the SRC node: +- compatible: must be "stericsson,nomadik-src" +- reg: must contain the SRC register base and size + +Optional properties for the SRC node: +- disable-sxtalo: if present this will disable the SXTALO + i.e. the driver output for the slow 32kHz chrystal, if the + board has its own circuitry for providing this oscillator +- disable-mxtal: if present this will disable the MXTALO, + i.e. the driver output for the main (~19.2 MHz) chrystal, + if the board has its own circuitry for providing this + osciallator + + +PLL nodes: these nodes represent the two PLLs on the system, +which should both have the main chrystal, represented as a +fixed frequency clock, as parent. + +Required properties for the two PLL nodes: +- compatible: must be "st,nomadik-pll-clock" +- clock-cells: must be 0 +- clock-id: must be 1 or 2 for PLL1 and PLL2 respectively +- clocks: this clock will have main chrystal as parent + + +HCLK nodes: these represent the clock gates on individual +lines from the HCLK clock tree and the gate for individual +lines from the PCLK clock tree. + +Requires properties for the HCLK nodes: +- compatible: must be "st,nomadik-hclk-clock" +- clock-cells: must be 0 +- clock-id: must be the clock ID from 0 to 63 according to + this table: + + 0: HCLKDMA0 + 1: HCLKSMC + 2: HCLKSDRAM + 3: HCLKDMA1 + 4: HCLKCLCD + 5: PCLKIRDA + 6: PCLKSSP + 7: PCLKUART0 + 8: PCLKSDI + 9: PCLKI2C0 + 10: PCLKI2C1 + 11: PCLKUART1 + 12: PCLMSP0 + 13: HCLKUSB + 14: HCLKDIF + 15: HCLKSAA + 16: HCLKSVA + 17: PCLKHSI + 18: PCLKXTI + 19: PCLKUART2 + 20: PCLKMSP1 + 21: PCLKMSP2 + 22: PCLKOWM + 23: HCLKHPI + 24: PCLKSKE + 25: PCLKHSEM + 26: HCLK3D + 27: HCLKHASH + 28: HCLKCRYP + 29: PCLKMSHC + 30: HCLKUSBM + 31: HCLKRNG + (32, 33, 34, 35 RESERVED) + 36: CLDCLK + 37: IRDACLK + 38: SSPICLK + 39: UART0CLK + 40: SDICLK + 41: I2C0CLK + 42: I2C1CLK + 43: UART1CLK + 44: MSPCLK0 + 45: USBCLK + 46: DIFCLK + 47: IPI2CCLK + 48: IPBMCCLK + 49: HSICLKRX + 50: HSICLKTX + 51: UART2CLK + 52: MSPCLK1 + 53: MSPCLK2 + 54: OWMCLK + (55 RESERVED) + 56: SKECLK + (57 RESERVED) + 58: 3DCLK + 59: PCLKMSP3 + 60: MSPCLK3 + 61: MSHCCLK + 62: USBMCLK + 63: RNGCCLK diff --git a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt index 2b14a940eb7..3f454ffc654 100644 --- a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt +++ b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt @@ -10,11 +10,16 @@ Required properties: mapped region. - interrupts : G2D interrupt number to the CPU. + - clocks : from common clock binding: handle to G2D clocks. + - clock-names : from common clock binding: must contain "sclk_fimg2d" and + "fimg2d", corresponding to entries in the clocks property. Example: g2d@12800000 { compatible = "samsung,s5pv210-g2d"; reg = <0x12800000 0x1000>; interrupts = <0 89 0>; + clocks = <&clock 177>, <&clock 277>; + clock-names = "sclk_fimg2d", "fimg2d"; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt new file mode 100644 index 00000000000..1f8b0c507c2 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt @@ -0,0 +1,16 @@ +DT bindings for the R-/SH-Mobile irqpin controller + +Required properties: + +- compatible: has to be "renesas,intc-irqpin" +- #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in + interrupts.txt in this directory + +Optional properties: + +- any properties, listed in interrupts.txt, and any standard resource allocation + properties +- sense-bitfield-width: width of a single sense bitfield in the SENSE register, + if different from the default 4 bits +- control-parent: disable and enable interrupts on the parent interrupt + controller, needed for some broken implementations diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt index bf0182d8da2..df37b0230c7 100644 --- a/Documentation/devicetree/bindings/media/s5p-mfc.txt +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -15,6 +15,9 @@ Required properties: mapped region. - interrupts : MFC interrupt number to the CPU. + - clocks : from common clock binding: handle to mfc clocks. + - clock-names : from common clock binding: must contain "sclk_mfc" and "mfc", + corresponding to entries in the clocks property. - samsung,mfc-r : Base address of the first memory bank used by MFC for DMA contiguous memory allocation and its size. @@ -34,6 +37,8 @@ mfc: codec@13400000 { reg = <0x13400000 0x10000>; interrupts = <0 94 0>; samsung,power-domain = <&pd_mfc>; + clocks = <&clock 170>, <&clock 273>; + clock-names = "sclk_mfc", "mfc"; }; Board specific DT entry: diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt index c3a14e0ad0a..cd9e90c5d17 100644 --- a/Documentation/devicetree/bindings/mfd/ab8500.txt +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -120,7 +120,7 @@ ab8500 { "USB_LINK_STATUS", "USB_ADP_PROBE_PLUG", "USB_ADP_PROBE_UNPLUG"; - vddulpivio18-supply = <&ab8500_ldo_initcore_reg>; + vddulpivio18-supply = <&ab8500_ldo_intcore_reg>; v-ape-supply = <&db8500_vape_reg>; musb_1v8-supply = <&db8500_vsmps2_reg>; }; diff --git a/Documentation/devicetree/bindings/mmc/bcm,kona-sdhci.txt b/Documentation/devicetree/bindings/mmc/bcm,kona-sdhci.txt new file mode 100644 index 00000000000..094ae010f2f --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/bcm,kona-sdhci.txt @@ -0,0 +1,16 @@ +Broadcom BCM281xx SDHCI + +This file documents differences between the core properties in mmc.txt +and the properties present in the bcm281xx SDHCI + +Required properties: +- compatible : Should be "bcm,kona-sdhci" + +Example: + +sdio2: sdio@0x3f1a0000 { + compatible = "bcm,kona-sdhci"; + reg = <0x3f1a0000 0x10000>; + interrupts = <0x0 74 0x4>; +}; + diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt index bcfdab5d442..3a7caf7a744 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt @@ -58,7 +58,7 @@ Some requirements for using fsl,imx-pinctrl binding: Examples: usdhc@0219c000 { /* uSDHC4 */ - fsl,card-wired; + non-removable; vmmc-supply = <®_3p3v>; status = "okay"; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index c70fca146e9..e15cfc4bb39 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -21,8 +21,18 @@ Required Properties: - gpio-controller: identifies the node as a gpio controller and pin bank. - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO - binding is used, the amount of cells must be specified as 2. See generic - GPIO binding documentation for description of particular cells. + binding is used, the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + + Eg: <&gpx2 6 0> + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [flags]> + + Values for gpio specifier: + - Pin number: is a value between 0 to 7. + - Flags: 0 - Active High + 1 - Active Low - Pin mux/config groups as child nodes: The pin mux (selecting pin function mode) and pin config (pull up/down, driver strength) settings are represented @@ -266,3 +276,33 @@ Example 4: Set up the default pin state for uart controller. pinctrl = devm_pinctrl_get_select_default(&pdev->dev); } + +Example 5: A display port client node that supports 'default' pinctrl state + and gpio binding. + + display-port-controller { + /* ... */ + + samsung,hpd-gpio = <&gpx2 6 0>; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hpd>; + }; + +Example 6: Request the gpio for display port controller + + static int exynos_dp_probe(struct platform_device *pdev) + { + int hpd_gpio, ret; + struct device *dev = &pdev->dev; + struct device_node *dp_node = dev->of_node; + + /* ... */ + + hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0); + + /* ... */ + + ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN, + "hpd_gpio"); + /* ... */ + } diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index b3abde73601..d967ba16de6 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -48,3 +48,37 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; }; + +DWC3 +Required properties: + - compatible: should be "samsung,exynos5250-dwusb3" for USB 3.0 DWC3 + controller. + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property. + - ranges: allows valid 1:1 translation between child's address space and + parent's address space + - clocks: Clock IDs array as required by the controller. + - clock-names: names of clocks correseponding to IDs in the clock property + +Sub-nodes: +The dwc3 core should be added as subnode to Exynos dwc3 glue. +- dwc3 : + The binding details of dwc3 can be found in: + Documentation/devicetree/bindings/usb/dwc3.txt + +Example: + usb@12000000 { + compatible = "samsung,exynos5250-dwusb3"; + clocks = <&clock 286>; + clock-names = "usbdrd30"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dwc3 { + compatible = "synopsys,dwc3"; + reg = <0x12000000 0x10000>; + interrupts = <0 72 0>; + usb-phy = <&usb2_phy &usb3_phy>; + }; + }; diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt index c60da67a5d7..84f10c16cb3 100644 --- a/Documentation/devicetree/bindings/video/exynos_dp.txt +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt @@ -21,6 +21,10 @@ Required properties for dp-controller: of memory mapped region. -interrupts: interrupt combiner values. + -clocks: + from common clock binding: handle to dp clock. + -clock-names: + from common clock binding: Shall be "dp". -interrupt-parent: phandle to Interrupt combiner node. -samsung,color-space: @@ -61,6 +65,8 @@ SOC specific portion: reg = <0x145b0000 0x10000>; interrupts = <10 3>; interrupt-parent = <&combiner>; + clocks = <&clock 342>; + clock-names = "dp"; dptx-phy { reg = <0x10040720>; |