diff options
Diffstat (limited to 'Documentation/devicetree')
58 files changed, 1963 insertions, 86 deletions
diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/arm/atmel-adc.txt index c63097d6afe..16769d9cedd 100644 --- a/Documentation/devicetree/bindings/arm/atmel-adc.txt +++ b/Documentation/devicetree/bindings/arm/atmel-adc.txt @@ -14,9 +14,19 @@ Required properties: - atmel,adc-status-register: Offset of the Interrupt Status Register - atmel,adc-trigger-register: Offset of the Trigger Register - atmel,adc-vref: Reference voltage in millivolts for the conversions + - atmel,adc-res: List of resolution in bits supported by the ADC. List size + must be two at least. + - atmel,adc-res-names: Contains one identifier string for each resolution + in atmel,adc-res property. "lowres" and "highres" + identifiers are required. Optional properties: - atmel,adc-use-external: Boolean to enable of external triggers + - atmel,adc-use-res: String corresponding to an identifier from + atmel,adc-res-names property. If not specified, the highest + resolution will be used. + - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion + - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds Optional trigger Nodes: - Required properties: @@ -40,6 +50,9 @@ adc0: adc@fffb0000 { atmel,adc-trigger-register = <0x08>; atmel,adc-use-external; atmel,adc-vref = <3300>; + atmel,adc-res = <8 10>; + atmel,adc-res-names = "lowres", "highres"; + atmel,adc-use-res = "lowres"; trigger@0 { trigger-name = "external-rising"; diff --git a/Documentation/devicetree/bindings/arm/msm/ssbi.txt b/Documentation/devicetree/bindings/arm/msm/ssbi.txt new file mode 100644 index 00000000000..54fd5ced340 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/ssbi.txt @@ -0,0 +1,18 @@ +* Qualcomm SSBI + +Some Qualcomm MSM devices contain a point-to-point serial bus used to +communicate with a limited range of devices (mostly power management +chips). + +These require the following properties: + +- compatible: "qcom,ssbi" + +- qcom,controller-type + indicates the SSBI bus variant the controller should use to talk + with the slave device. This should be one of "ssbi", "ssbi2", or + "pmic-arbiter". The type chosen is determined by the attached + slave. + +The slave device should be the single child node of the ssbi device +with a compatible field. diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt new file mode 100644 index 00000000000..47ada1dff21 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt @@ -0,0 +1,60 @@ +Samsung Exynos Analog to Digital Converter bindings + +The devicetree bindings are for the new ADC driver written for +Exynos4 and upward SoCs from Samsung. + +New driver handles the following +1. Supports ADC IF found on EXYNOS4412/EXYNOS5250 + and future SoCs from Samsung +2. Add ADC driver under iio/adc framework +3. Also adds the Documentation for device tree bindings + +Required properties: +- compatible: Must be "samsung,exynos-adc-v1" + for exynos4412/5250 controllers. + Must be "samsung,exynos-adc-v2" for + future controllers. +- reg: Contains ADC register address range (base address and + length) and the address of the phy enable register. +- interrupts: Contains the interrupt information for the timer. The + format is being dependent on which interrupt controller + the Samsung device uses. +- #io-channel-cells = <1>; As ADC has multiple outputs +- clocks From common clock binding: handle to adc clock. +- clock-names From common clock binding: Shall be "adc". +- vdd-supply VDD input supply. + +Note: child nodes can be added for auto probing from device tree. + +Example: adding device info in dtsi file + +adc: adc@12D10000 { + compatible = "samsung,exynos-adc-v1"; + reg = <0x12D10000 0x100>, <0x10040718 0x4>; + interrupts = <0 106 0>; + #io-channel-cells = <1>; + io-channel-ranges; + + clocks = <&clock 303>; + clock-names = "adc"; + + vdd-supply = <&buck5_reg>; +}; + + +Example: Adding child nodes in dts file + +adc@12D10000 { + + /* NTC thermistor is a hwmon device */ + ncp15wb473@0 { + compatible = "ntc,ncp15wb473"; + pullup-uV = <1800000>; + pullup-ohm = <47000>; + pulldown-ohm = <0>; + io-channels = <&adc 4>; + }; +}; + +Note: Does not apply to ADC driver under arch/arm/plat-samsung/ +Note: The child node can be added under the adc node or separately. diff --git a/Documentation/devicetree/bindings/ata/imx-pata.txt b/Documentation/devicetree/bindings/ata/imx-pata.txt new file mode 100644 index 00000000000..e38d73414b0 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/imx-pata.txt @@ -0,0 +1,17 @@ +* Freescale i.MX PATA Controller + +Required properties: +- compatible: "fsl,imx27-pata" +- reg: Address range of the PATA Controller +- interrupts: The interrupt of the PATA Controller +- clocks: the clocks for the PATA Controller + +Example: + + pata: pata@83fe0000 { + compatible = "fsl,imx51-pata", "fsl,imx27-pata"; + reg = <0x83fe0000 0x4000>; + interrupts = <70>; + clocks = <&clks 161>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/axi-clkgen.txt b/Documentation/devicetree/bindings/clock/axi-clkgen.txt new file mode 100644 index 00000000000..028b493e97f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/axi-clkgen.txt @@ -0,0 +1,22 @@ +Binding for the axi-clkgen clock generator + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "adi,axi-clkgen". +- #clock-cells : from common clock binding; Should always be set to 0. +- reg : Address and length of the axi-clkgen register set. +- clocks : Phandle and clock specifier for the parent clock. + +Optional properties: +- clock-output-names : From common clock binding. + +Example: + clock@0xff000000 { + compatible = "adi,axi-clkgen"; + #clock-cells = <0>; + reg = <0xff000000 0x1000>; + clocks = <&osc 1>; + }; diff --git a/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt b/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt new file mode 100644 index 00000000000..5757f9abfc2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt @@ -0,0 +1,24 @@ +Binding for simple fixed factor rate clock sources. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "fixed-factor-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- clock-div: fixed divider. +- clock-mult: fixed multiplier. +- clocks: parent clock. + +Optional properties: +- clock-output-names : From common clock binding. + +Example: + clock { + compatible = "fixed-factor-clock"; + clocks = <&parentclk>; + #clock-cells = <0>; + div = <2>; + mult = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt new file mode 100644 index 00000000000..cc374651662 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt @@ -0,0 +1,114 @@ +Binding for Silicon Labs Si5351a/b/c programmable i2c clock generator. + +Reference +[1] Si5351A/B/C Data Sheet + http://www.silabs.com/Support%20Documents/TechnicalDocs/Si5351.pdf + +The Si5351a/b/c are programmable i2c clock generators with upto 8 output +clocks. Si5351a also has a reduced pin-count package (MSOP10) where only +3 output clocks are accessible. The internal structure of the clock +generators can be found in [1]. + +==I2C device node== + +Required properties: +- compatible: shall be one of "silabs,si5351{a,a-msop,b,c}". +- reg: i2c device address, shall be 0x60 or 0x61. +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: from common clock binding; list of parent clock + handles, shall be xtal reference clock or xtal and clkin for + si5351c only. +- #address-cells: shall be set to 1. +- #size-cells: shall be set to 0. + +Optional properties: +- silabs,pll-source: pair of (number, source) for each pll. Allows + to overwrite clock source of pll A (number=0) or B (number=1). + +==Child nodes== + +Each of the clock outputs can be overwritten individually by +using a child node to the I2C device node. If a child node for a clock +output is not set, the eeprom configuration is not overwritten. + +Required child node properties: +- reg: number of clock output. + +Optional child node properties: +- silabs,clock-source: source clock of the output divider stage N, shall be + 0 = multisynth N + 1 = multisynth 0 for output clocks 0-3, else multisynth4 + 2 = xtal + 3 = clkin (si5351c only) +- silabs,drive-strength: output drive strength in mA, shall be one of {2,4,6,8}. +- silabs,multisynth-source: source pll A(0) or B(1) of corresponding multisynth + divider. +- silabs,pll-master: boolean, multisynth can change pll frequency. + +==Example== + +/* 25MHz reference crystal */ +ref25: ref25M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; +}; + +i2c-master-node { + + /* Si5351a msop10 i2c clock generator */ + si5351a: clock-generator@60 { + compatible = "silabs,si5351a-msop"; + reg = <0x60>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + + /* connect xtal input to 25MHz reference */ + clocks = <&ref25>; + + /* connect xtal input as source of pll0 and pll1 */ + silabs,pll-source = <0 0>, <1 0>; + + /* + * overwrite clkout0 configuration with: + * - 8mA output drive strength + * - pll0 as clock source of multisynth0 + * - multisynth0 as clock source of output divider + * - multisynth0 can change pll0 + * - set initial clock frequency of 74.25MHz + */ + clkout0 { + reg = <0>; + silabs,drive-strength = <8>; + silabs,multisynth-source = <0>; + silabs,clock-source = <0>; + silabs,pll-master; + clock-frequency = <74250000>; + }; + + /* + * overwrite clkout1 configuration with: + * - 4mA output drive strength + * - pll1 as clock source of multisynth1 + * - multisynth1 as clock source of output divider + * - multisynth1 can change pll1 + */ + clkout1 { + reg = <1>; + silabs,drive-strength = <4>; + silabs,multisynth-source = <1>; + silabs,clock-source = <0>; + pll-master; + }; + + /* + * overwrite clkout2 configuration with: + * - xtal as clock source of output divider + */ + clkout2 { + reg = <2>; + silabs,clock-source = <2>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt new file mode 100644 index 00000000000..729f52426fe --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -0,0 +1,151 @@ +Device Tree Clock bindings for arch-sunxi + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "allwinner,sun4i-osc-clk" - for a gatable oscillator + "allwinner,sun4i-pll1-clk" - for the main PLL clock + "allwinner,sun4i-cpu-clk" - for the CPU multiplexer clock + "allwinner,sun4i-axi-clk" - for the AXI clock + "allwinner,sun4i-axi-gates-clk" - for the AXI gates + "allwinner,sun4i-ahb-clk" - for the AHB clock + "allwinner,sun4i-ahb-gates-clk" - for the AHB gates + "allwinner,sun4i-apb0-clk" - for the APB0 clock + "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates + "allwinner,sun4i-apb1-clk" - for the APB1 clock + "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing + "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates + +Required properties for all clocks: +- reg : shall be the control register address for the clock. +- clocks : shall be the input parent clock(s) phandle for the clock +- #clock-cells : from common clock binding; shall be set to 0 except for + "allwinner,sun4i-*-gates-clk" where it shall be set to 1 + +Additionally, "allwinner,sun4i-*-gates-clk" clocks require: +- clock-output-names : the corresponding gate names that the clock controls + +For example: + +osc24M: osc24M@01c20050 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-osc-clk"; + reg = <0x01c20050 0x4>; + clocks = <&osc24M_fixed>; +}; + +pll1: pll1@01c20000 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-pll1-clk"; + reg = <0x01c20000 0x4>; + clocks = <&osc24M>; +}; + +cpu: cpu@01c20054 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-cpu-clk"; + reg = <0x01c20054 0x4>; + clocks = <&osc32k>, <&osc24M>, <&pll1>; +}; + + + +Gate clock outputs + +The "allwinner,sun4i-*-gates-clk" clocks provide several gatable outputs; +their corresponding offsets as present on sun4i are listed below. Note that +some of these gates are not present on sun5i. + + * AXI gates ("allwinner,sun4i-axi-gates-clk") + + DRAM 0 + + * AHB gates ("allwinner,sun4i-ahb-gates-clk") + + USB0 0 + EHCI0 1 + OHCI0 2* + EHCI1 3 + OHCI1 4* + SS 5 + DMA 6 + BIST 7 + MMC0 8 + MMC1 9 + MMC2 10 + MMC3 11 + MS 12** + NAND 13 + SDRAM 14 + + ACE 16 + EMAC 17 + TS 18 + + SPI0 20 + SPI1 21 + SPI2 22 + SPI3 23 + PATA 24 + SATA 25** + GPS 26* + + VE 32 + TVD 33 + TVE0 34 + TVE1 35 + LCD0 36 + LCD1 37 + + CSI0 40 + CSI1 41 + + HDMI 43 + DE_BE0 44 + DE_BE1 45 + DE_FE0 46 + DE_FE1 47 + + MP 50 + + MALI400 52 + + * APB0 gates ("allwinner,sun4i-apb0-gates-clk") + + CODEC 0 + SPDIF 1* + AC97 2 + IIS 3 + + PIO 5 + IR0 6 + IR1 7 + + KEYPAD 10 + + * APB1 gates ("allwinner,sun4i-apb1-gates-clk") + + I2C0 0 + I2C1 1 + I2C2 2 + + CAN 4 + SCR 5 + PS20 6 + PS21 7 + + UART0 16 + UART1 17 + UART2 18 + UART3 19 + UART4 20 + UART5 21 + UART6 22 + UART7 23 + +Notation: + [*]: The datasheet didn't mention these, but they are present on AW code + [**]: The datasheet had this marked as "NC" but they are used on AW code diff --git a/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt b/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt new file mode 100644 index 00000000000..0715695e94a --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt @@ -0,0 +1,65 @@ +Generic ARM big LITTLE cpufreq driver's DT glue +----------------------------------------------- + +This is DT specific glue layer for generic cpufreq driver for big LITTLE +systems. + +Both required and optional properties listed below must be defined +under node /cpus/cpu@x. Where x is the first cpu inside a cluster. + +FIXME: Cpus should boot in the order specified in DT and all cpus for a cluster +must be present contiguously. Generic DT driver will check only node 'x' for +cpu:x. + +Required properties: +- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt + for details + +Optional properties: +- clock-latency: Specify the possible maximum transition latency for clock, + in unit of nanoseconds. + +Examples: + +cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a15"; + reg = <0>; + next-level-cache = <&L2>; + operating-points = < + /* kHz uV */ + 792000 1100000 + 396000 950000 + 198000 850000 + >; + clock-latency = <61036>; /* two CLK32 periods */ + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + reg = <1>; + next-level-cache = <&L2>; + }; + + cpu@100 { + compatible = "arm,cortex-a7"; + reg = <100>; + next-level-cache = <&L2>; + operating-points = < + /* kHz uV */ + 792000 950000 + 396000 750000 + 198000 450000 + >; + clock-latency = <61036>; /* two CLK32 periods */ + }; + + cpu@101 { + compatible = "arm,cortex-a7"; + reg = <101>; + next-level-cache = <&L2>; + }; +}; diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt index 4416ccc3347..051f764bedb 100644 --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt @@ -32,7 +32,7 @@ cpus { 396000 950000 198000 850000 >; - transition-latency = <61036>; /* two CLK32 periods */ + clock-latency = <61036>; /* two CLK32 periods */ }; cpu@1 { diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-exynos5440.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-exynos5440.txt new file mode 100644 index 00000000000..caff1a57436 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-exynos5440.txt @@ -0,0 +1,28 @@ + +Exynos5440 cpufreq driver +------------------- + +Exynos5440 SoC cpufreq driver for CPU frequency scaling. + +Required properties: +- interrupts: Interrupt to know the completion of cpu frequency change. +- operating-points: Table of frequencies and voltage CPU could be transitioned into, + in the decreasing order. Frequency should be in KHz units and voltage + should be in microvolts. + +Optional properties: +- clock-latency: Clock monitor latency in microsecond. + +All the required listed above must be defined under node cpufreq. + +Example: +-------- + cpufreq@160000 { + compatible = "samsung,exynos5440-cpufreq"; + reg = <0x160000 0x1000>; + interrupts = <0 57 0>; + operating-points = < + 1000000 975000 + 800000 925000>; + clock-latency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index a33628759d3..d933af37069 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -98,7 +98,7 @@ announce the pinrange to the pin ctrl subsystem. For example, compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; reg = <0x1460 0x18>; gpio-controller; - gpio-ranges = <&pinctrl1 20 10>, <&pinctrl2 50 20>; + gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>; } @@ -107,8 +107,8 @@ where, Next values specify the base pin and number of pins for the range handled by 'qe_pio_e' gpio. In the given example from base pin 20 to - pin 29 under pinctrl1 and pin 50 to pin 69 under pinctrl2 is handled - by this gpio controller. + pin 29 under pinctrl1 with gpio offset 0 and pin 50 to pin 69 under + pinctrl2 with gpio offset 10 is handled by this gpio controller. The pinctrl node must have "#gpio-range-cells" property to show number of arguments to pass with phandle from gpio controllers node. diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt new file mode 100644 index 00000000000..c6f66674f19 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -0,0 +1,29 @@ +NTC Thermistor hwmon sensors +------------------------------- + +Requires node properties: +- "compatible" value : one of + "ntc,ncp15wb473" + "ntc,ncp18wb473" + "ntc,ncp21wb473" + "ntc,ncp03wb473" + "ntc,ncp15wl333" +- "pullup-uv" Pull up voltage in micro volts +- "pullup-ohm" Pull up resistor value in ohms +- "pulldown-ohm" Pull down resistor value in ohms +- "connected-positive" Always ON, If not specified. + Status change is possible. +- "io-channels" Channel node of ADC to be used for + conversion. + +Read more about iio bindings at + Documentation/devicetree/bindings/iio/iio-bindings.txt + +Example: + ncp15wb473@0 { + compatible = "ntc,ncp15wb473"; + pullup-uv = <1800000>; + pullup-ohm = <47000>; + pulldown-ohm = <0>; + io-channels = <&adc 3>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index f98d4c5b5cc..296eb453612 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -26,7 +26,7 @@ Required for all cases except "samsung,s3c2440-hdmiphy-i2c": - pinctrl-names: Should contain only one value - "default". Optional properties: - - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not + - samsung,i2c-slave-addr: Slave address in multi-master environment. If not specified, default value is 0. - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not specified, the default value in Hz is 100000. diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 446859fcdca..ad6a73852f0 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -35,6 +35,8 @@ fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec +infineon,slb9635tt Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz) +infineon,slb9645tt Infineon SLB9645 I2C TPM (new protocol, max 400khz) maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface diff --git a/Documentation/devicetree/bindings/iio/iio-bindings.txt b/Documentation/devicetree/bindings/iio/iio-bindings.txt new file mode 100644 index 00000000000..0b447d9ad19 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/iio-bindings.txt @@ -0,0 +1,97 @@ +This binding is derived from clock bindings, and based on suggestions +from Lars-Peter Clausen [1]. + +Sources of IIO channels can be represented by any node in the device +tree. Those nodes are designated as IIO providers. IIO consumer +nodes use a phandle and IIO specifier pair to connect IIO provider +outputs to IIO inputs. Similar to the gpio specifiers, an IIO +specifier is an array of one or more cells identifying the IIO +output on a device. The length of an IIO specifier is defined by the +value of a #io-channel-cells property in the IIO provider node. + +[1] http://marc.info/?l=linux-iio&m=135902119507483&w=2 + +==IIO providers== + +Required properties: +#io-channel-cells: Number of cells in an IIO specifier; Typically 0 for nodes + with a single IIO output and 1 for nodes with multiple + IIO outputs. + +Example for a simple configuration with no trigger: + + adc: voltage-sensor@35 { + compatible = "maxim,max1139"; + reg = <0x35>; + #io-channel-cells = <1>; + }; + +Example for a configuration with trigger: + + adc@35 { + compatible = "some-vendor,some-adc"; + reg = <0x35>; + + adc1: iio-device@0 { + #io-channel-cells = <1>; + /* other properties */ + }; + adc2: iio-device@1 { + #io-channel-cells = <1>; + /* other properties */ + }; + }; + +==IIO consumers== + +Required properties: +io-channels: List of phandle and IIO specifier pairs, one pair + for each IIO input to the device. Note: if the + IIO provider specifies '0' for #io-channel-cells, + then only the phandle portion of the pair will appear. + +Optional properties: +io-channel-names: + List of IIO input name strings sorted in the same + order as the io-channels property. Consumers drivers + will use io-channel-names to match IIO input names + with IIO specifiers. +io-channel-ranges: + Empty property indicating that child nodes can inherit named + IIO channels from this node. Useful for bus nodes to provide + and IIO channel to their children. + +For example: + + device { + io-channels = <&adc 1>, <&ref 0>; + io-channel-names = "vcc", "vdd"; + }; + +This represents a device with two IIO inputs, named "vcc" and "vdd". +The vcc channel is connected to output 1 of the &adc device, and the +vdd channel is connected to output 0 of the &ref device. + +==Example== + + adc: max1139@35 { + compatible = "maxim,max1139"; + reg = <0x35>; + #io-channel-cells = <1>; + }; + + ... + + iio_hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, + <&adc 3>, <&adc 4>, <&adc 5>, + <&adc 6>, <&adc 7>, <&adc 8>, + <&adc 9>; + }; + + some_consumer { + compatible = "some-consumer"; + io-channels = <&adc 10>, <&adc 11>; + io-channel-names = "adc1", "adc2"; + }; diff --git a/Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt b/Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt new file mode 100644 index 00000000000..3029c5694cf --- /dev/null +++ b/Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt @@ -0,0 +1,16 @@ +Aeroflex Gaisler APBPS2 PS/2 Core, supporting Keyboard or Mouse. + +The APBPS2 PS/2 core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the APBPS2 core, a LEON SPARC system, +these properties are built from information in the AMBA plug&play and from +bootloader settings. + +Required properties: + +- name : Should be "GAISLER_APBPS2" or "01_060" +- reg : Address and length of the register set for the device +- interrupts : Interrupt numbers for this device + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt new file mode 100644 index 00000000000..f40f21c642b --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt @@ -0,0 +1,30 @@ +* AUO in-cell touchscreen controller using Pixcir sensors + +Required properties: +- compatible: must be "auo,auo_pixcir_ts" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- gpios: gpios the chip is connected to + first one is the interrupt gpio and second one the reset gpio +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Example: + + i2c@00000000 { + /* ... */ + + auo_pixcir_ts@5c { + compatible = "auo,auo_pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + + gpios = <&gpf 2 0 2>, /* INT */ + <&gpf 5 1 0>; /* RST */ + + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt new file mode 100644 index 00000000000..64ad48b824a --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt @@ -0,0 +1,24 @@ +* Sitronix st1232 touchscreen controller + +Required properties: +- compatible: must be "sitronix,st1232" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected + +Optional properties: +- gpios: a phandle to the reset GPIO + +Example: + + i2c@00000000 { + /* ... */ + + touchscreen@55 { + compatible = "sitronix,st1232"; + reg = <0x55>; + interrupts = <2 0>; + gpios = <&gpio1 166 0>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/leds/tca6507.txt b/Documentation/devicetree/bindings/leds/tca6507.txt index 2b6693b972f..80ff3dfb1f3 100644 --- a/Documentation/devicetree/bindings/leds/tca6507.txt +++ b/Documentation/devicetree/bindings/leds/tca6507.txt @@ -1,4 +1,4 @@ -LEDs conected to tca6507 +LEDs connected to tca6507 Required properties: - compatible : should be : "ti,tca6507". diff --git a/Documentation/devicetree/bindings/media/coda.txt b/Documentation/devicetree/bindings/media/coda.txt new file mode 100644 index 00000000000..2865d04e403 --- /dev/null +++ b/Documentation/devicetree/bindings/media/coda.txt @@ -0,0 +1,30 @@ +Chips&Media Coda multi-standard codec IP +======================================== + +Coda codec IPs are present in i.MX SoCs in various versions, +called VPU (Video Processing Unit). + +Required properties: +- compatible : should be "fsl,<chip>-src" for i.MX SoCs: + (a) "fsl,imx27-vpu" for CodaDx6 present in i.MX27 + (b) "fsl,imx53-vpu" for CODA7541 present in i.MX53 + (c) "fsl,imx6q-vpu" for CODA960 present in i.MX6q +- reg: should be register base and length as documented in the + SoC reference manual +- interrupts : Should contain the VPU interrupt. For CODA960, + a second interrupt is needed for the MJPEG unit. +- clocks : Should contain the ahb and per clocks, in the order + determined by the clock-names property. +- clock-names : Should be "ahb", "per" +- iram : phandle pointing to the SRAM device node + +Example: + +vpu: vpu@63ff4000 { + compatible = "fsl,imx53-vpu"; + reg = <0x63ff4000 0x1000>; + interrupts = <9>; + clocks = <&clks 63>, <&clks 63>; + clock-names = "ahb", "per"; + iram = <&ocram>; +}; diff --git a/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt new file mode 100644 index 00000000000..3f62adfb3e0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt @@ -0,0 +1,14 @@ +Exynos4x12/Exynos5 SoC series camera host interface (FIMC-LITE) + +Required properties: + +- compatible : should be "samsung,exynos4212-fimc" for Exynos4212 and + Exynos4412 SoCs; +- reg : physical base address and size of the device memory mapped + registers; +- interrupts : should contain FIMC-LITE interrupt; +- clocks : FIMC LITE gate clock should be specified in this property. +- clock-names : should contain "flite" entry. + +Each FIMC device should have an alias in the aliases node, in the form of +fimc-lite<n>, where <n> is an integer specifying the IP block instance. diff --git a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt new file mode 100644 index 00000000000..55c9ad6f959 --- /dev/null +++ b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt @@ -0,0 +1,49 @@ +Exynos4x12 SoC series Imaging Subsystem (FIMC-IS) + +The FIMC-IS is a subsystem for processing image signal from an image sensor. +The Exynos4x12 SoC series FIMC-IS V1.5 comprises of a dedicated ARM Cortex-A5 +processor, ISP, DRC and FD IP blocks and peripheral devices such as UART, I2C +and SPI bus controllers, PWM and ADC. + +fimc-is node +------------ + +Required properties: +- compatible : should be "samsung,exynos4212-fimc-is" for Exynos4212 and + Exynos4412 SoCs; +- reg : physical base address and length of the registers set; +- interrupts : must contain two FIMC-IS interrupts, in order: ISP0, ISP1; +- clocks : list of clock specifiers, corresponding to entries in + clock-names property; +- clock-names : must contain "ppmuispx", "ppmuispx", "lite0", "lite1" + "mpll", "sysreg", "isp", "drc", "fd", "mcuisp", "uart", + "ispdiv0", "ispdiv1", "mcuispdiv0", "mcuispdiv1", "aclk200", + "div_aclk200", "aclk400mcuisp", "div_aclk400mcuisp" entries, + matching entries in the clocks property. +pmu subnode +----------- + +Required properties: + - reg : must contain PMU physical base address and size of the register set. + +The following are the FIMC-IS peripheral device nodes and can be specified +either standalone or as the fimc-is node child nodes. + +i2c-isp (ISP I2C bus controller) nodes +------------------------------------------ + +Required properties: + +- compatible : should be "samsung,exynos4212-i2c-isp" for Exynos4212 and + Exynos4412 SoCs; +- reg : physical base address and length of the registers set; +- clocks : must contain gate clock specifier for this controller; +- clock-names : must contain "i2c_isp" entry. + +For the above nodes it is required to specify a pinctrl state named "default", +according to the pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt. + +Device tree nodes of the image sensors' controlled directly by the FIMC-IS +firmware must be child nodes of their corresponding ISP I2C bus controller node. +The data link of these image sensors must be specified using the common video +interfaces bindings, defined in video-interfaces.txt. diff --git a/Documentation/devicetree/bindings/media/samsung-fimc.txt b/Documentation/devicetree/bindings/media/samsung-fimc.txt new file mode 100644 index 00000000000..51c776b7f7a --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-fimc.txt @@ -0,0 +1,197 @@ +Samsung S5P/EXYNOS SoC Camera Subsystem (FIMC) +---------------------------------------------- + +The S5P/Exynos SoC Camera subsystem comprises of multiple sub-devices +represented by separate device tree nodes. Currently this includes: FIMC (in +the S5P SoCs series known as CAMIF), MIPI CSIS, FIMC-LITE and FIMC-IS (ISP). + +The sub-subdevices are defined as child nodes of the common 'camera' node which +also includes common properties of the whole subsystem not really specific to +any single sub-device, like common camera port pins or the CAMCLK clock outputs +for external image sensors attached to an SoC. + +Common 'camera' node +-------------------- + +Required properties: + +- compatible : must be "samsung,fimc", "simple-bus" +- clocks : list of clock specifiers, corresponding to entries in + the clock-names property; +- clock-names : must contain "sclk_cam0", "sclk_cam1", "pxl_async0", + "pxl_async1" entries, matching entries in the clocks property. + +The pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt must be used +to define a required pinctrl state named "default" and optional pinctrl states: +"idle", "active-a", active-b". These optional states can be used to switch the +camera port pinmux at runtime. The "idle" state should configure both the camera +ports A and B into high impedance state, especially the CAMCLK clock output +should be inactive. For the "active-a" state the camera port A must be activated +and the port B deactivated and for the state "active-b" it should be the other +way around. + +The 'camera' node must include at least one 'fimc' child node. + +'fimc' device nodes +------------------- + +Required properties: + +- compatible: "samsung,s5pv210-fimc" for S5PV210, "samsung,exynos4210-fimc" + for Exynos4210 and "samsung,exynos4212-fimc" for Exynos4x12 SoCs; +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain FIMC interrupt; +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names; +- clock-names: must contain "fimc", "sclk_fimc" entries. +- samsung,pix-limits: an array of maximum supported image sizes in pixels, for + details refer to Table 2-1 in the S5PV210 SoC User Manual; The meaning of + each cell is as follows: + 0 - scaler input horizontal size, + 1 - input horizontal size for the scaler bypassed, + 2 - REAL_WIDTH without input rotation, + 3 - REAL_HEIGHT with input rotation, +- samsung,sysreg: a phandle to the SYSREG node. + +Each FIMC device should have an alias in the aliases node, in the form of +fimc<n>, where <n> is an integer specifying the IP block instance. + +Optional properties: + +- clock-frequency: maximum FIMC local clock (LCLK) frequency; +- samsung,min-pix-sizes: an array specyfing minimum image size in pixels at + the FIMC input and output DMA, in the first and second cell respectively. + Default value when this property is not present is <16 16>; +- samsung,min-pix-alignment: minimum supported image height alignment (first + cell) and the horizontal image offset (second cell). The values are in pixels + and default to <2 1> when this property is not present; +- samsung,mainscaler-ext: a boolean property indicating whether the FIMC IP + supports extended image size and has CIEXTEN register; +- samsung,rotators: a bitmask specifying whether this IP has the input and + the output rotator. Bits 4 and 0 correspond to input and output rotator + respectively. If a rotator is present its corresponding bit should be set. + Default value when this property is not specified is 0x11. +- samsung,cam-if: a bolean property indicating whether the IP block includes + the camera input interface. +- samsung,isp-wb: this property must be present if the IP block has the ISP + writeback input. +- samsung,lcd-wb: this property must be present if the IP block has the LCD + writeback input. + + +'parallel-ports' node +--------------------- + +This node should contain child 'port' nodes specifying active parallel video +input ports. It includes camera A and camera B inputs. 'reg' property in the +port nodes specifies data input - 0, 1 indicates input A, B respectively. + +Optional properties + +- samsung,camclk-out : specifies clock output for remote sensor, + 0 - CAM_A_CLKOUT, 1 - CAM_B_CLKOUT; + +Image sensor nodes +------------------ + +The sensor device nodes should be added to their control bus controller (e.g. +I2C0) nodes and linked to a port node in the csis or the parallel-ports node, +using the common video interfaces bindings, defined in video-interfaces.txt. +The implementation of this bindings requires clock-frequency property to be +present in the sensor device nodes. + +Example: + + aliases { + fimc0 = &fimc_0; + }; + + /* Parallel bus IF sensor */ + i2c_0: i2c@13860000 { + s5k6aa: sensor@3c { + compatible = "samsung,s5k6aafx"; + reg = <0x3c>; + vddio-supply = <...>; + + clock-frequency = <24000000>; + clocks = <...>; + clock-names = "mclk"; + + port { + s5k6aa_ep: endpoint { + remote-endpoint = <&fimc0_ep>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <1>; + pclk-sample = <1>; + }; + }; + }; + }; + + /* MIPI CSI-2 bus IF sensor */ + s5c73m3: sensor@0x1a { + compatible = "samsung,s5c73m3"; + reg = <0x1a>; + vddio-supply = <...>; + + clock-frequency = <24000000>; + clocks = <...>; + clock-names = "mclk"; + + port { + s5c73m3_1: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&csis0_ep>; + }; + }; + }; + + camera { + compatible = "samsung,fimc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cam_port_a_clk_active>; + + /* parallel camera ports */ + parallel-ports { + /* camera A input */ + port@0 { + reg = <0>; + fimc0_ep: endpoint { + remote-endpoint = <&s5k6aa_ep>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <1>; + pclk-sample = <1>; + }; + }; + }; + + fimc_0: fimc@11800000 { + compatible = "samsung,exynos4210-fimc"; + reg = <0x11800000 0x1000>; + interrupts = <0 85 0>; + status = "okay"; + }; + + csis_0: csis@11880000 { + compatible = "samsung,exynos4210-csis"; + reg = <0x11880000 0x1000>; + interrupts = <0 78 0>; + /* camera C input */ + port@3 { + reg = <3>; + csis0_ep: endpoint { + remote-endpoint = <&s5c73m3_ep>; + data-lanes = <1 2 3 4>; + samsung,csis-hs-settle = <12>; + }; + }; + }; + }; + +The MIPI-CSIS device binding is defined in samsung-mipi-csis.txt. diff --git a/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt b/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt new file mode 100644 index 00000000000..5f8e28e2484 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt @@ -0,0 +1,81 @@ +Samsung S5P/EXYNOS SoC series MIPI CSI-2 receiver (MIPI CSIS) +------------------------------------------------------------- + +Required properties: + +- compatible : "samsung,s5pv210-csis" for S5PV210 (S5PC110), + "samsung,exynos4210-csis" for Exynos4210 (S5PC210), + "samsung,exynos4212-csis" for Exynos4212/Exynos4412 + SoC series; +- reg : offset and length of the register set for the device; +- interrupts : should contain MIPI CSIS interrupt; the format of the + interrupt specifier depends on the interrupt controller; +- bus-width : maximum number of data lanes supported (SoC specific); +- vddio-supply : MIPI CSIS I/O and PLL voltage supply (e.g. 1.8V); +- vddcore-supply : MIPI CSIS Core voltage supply (e.g. 1.1V); +- clocks : list of clock specifiers, corresponding to entries in + clock-names property; +- clock-names : must contain "csis", "sclk_csis" entries, matching entries + in the clocks property. + +Optional properties: + +- clock-frequency : The IP's main (system bus) clock frequency in Hz, default + value when this property is not specified is 166 MHz; +- samsung,csis-wclk : CSI-2 wrapper clock selection. If this property is present + external clock from CMU will be used, or the bus clock if + if it's not specified. + +The device node should contain one 'port' child node with one child 'endpoint' +node, according to the bindings defined in Documentation/devicetree/bindings/ +media/video-interfaces.txt. The following are properties specific to those nodes. + +port node +--------- + +- reg : (required) must be 3 for camera C input (CSIS0) or 4 for + camera D input (CSIS1); + +endpoint node +------------- + +- data-lanes : (required) an array specifying active physical MIPI-CSI2 + data input lanes and their mapping to logical lanes; the + array's content is unused, only its length is meaningful; + +- samsung,csis-hs-settle : (optional) differential receiver (HS-RX) settle time; + + +Example: + + reg0: regulator@0 { + }; + + reg1: regulator@1 { + }; + +/* SoC properties */ + + csis_0: csis@11880000 { + compatible = "samsung,exynos4210-csis"; + reg = <0x11880000 0x1000>; + interrupts = <0 78 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + +/* Board properties */ + + csis_0: csis@11880000 { + clock-frequency = <166000000>; + vddio-supply = <®0>; + vddcore-supply = <®1>; + port { + reg = <3>; /* 3 - CSIS0, 4 - CSIS1 */ + csis0_ep: endpoint { + remote-endpoint = <...>; + data-lanes = <1>, <2>; + samsung,csis-hs-settle = <12>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt new file mode 100644 index 00000000000..e022d2dc496 --- /dev/null +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -0,0 +1,228 @@ +Common bindings for video receiver and transmitter interfaces + +General concept +--------------- + +Video data pipelines usually consist of external devices, e.g. camera sensors, +controlled over an I2C, SPI or UART bus, and SoC internal IP blocks, including +video DMA engines and video data processors. + +SoC internal blocks are described by DT nodes, placed similarly to other SoC +blocks. External devices are represented as child nodes of their respective +bus controller nodes, e.g. I2C. + +Data interfaces on all video devices are described by their child 'port' nodes. +Configuration of a port depends on other devices participating in the data +transfer and is described by 'endpoint' subnodes. + +device { + ... + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + ... + endpoint@0 { ... }; + endpoint@1 { ... }; + }; + port@1 { ... }; + }; +}; + +If a port can be configured to work with more than one remote device on the same +bus, an 'endpoint' child node must be provided for each of them. If more than +one port is present in a device node or there is more than one endpoint at a +port, or port node needs to be associated with a selected hardware interface, +a common scheme using '#address-cells', '#size-cells' and 'reg' properties is +used. + +All 'port' nodes can be grouped under optional 'ports' node, which allows to +specify #address-cells, #size-cells properties independently for the 'port' +and 'endpoint' nodes and any child device nodes a device might have. + +Two 'endpoint' nodes are linked with each other through their 'remote-endpoint' +phandles. An endpoint subnode of a device contains all properties needed for +configuration of this device for data exchange with other device. In most +cases properties at the peer 'endpoint' nodes will be identical, however they +might need to be different when there is any signal modifications on the bus +between two devices, e.g. there are logic signal inverters on the lines. + +It is allowed for multiple endpoints at a port to be active simultaneously, +where supported by a device. For example, in case where a data interface of +a device is partitioned into multiple data busses, e.g. 16-bit input port +divided into two separate ITU-R BT.656 8-bit busses. In such case bus-width +and data-shift properties can be used to assign physical data lines to each +endpoint node (logical bus). + + +Required properties +------------------- + +If there is more than one 'port' or more than one 'endpoint' node or 'reg' +property is present in port and/or endpoint nodes the following properties +are required in a relevant parent node: + + - #address-cells : number of cells required to define port/endpoint + identifier, should be 1. + - #size-cells : should be zero. + +Optional endpoint properties +---------------------------- + +- remote-endpoint: phandle to an 'endpoint' subnode of a remote device node. +- slave-mode: a boolean property indicating that the link is run in slave mode. + The default when this property is not specified is master mode. In the slave + mode horizontal and vertical synchronization signals are provided to the + slave device (data source) by the master device (data sink). In the master + mode the data source device is also the source of the synchronization signals. +- bus-width: number of data lines actively used, valid for the parallel busses. +- data-shift: on the parallel data busses, if bus-width is used to specify the + number of data lines, data-shift can be used to specify which data lines are + used, e.g. "bus-width=<8>; data-shift=<2>;" means, that lines 9:2 are used. +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. + Note, that if HSYNC and VSYNC polarities are not specified, embedded + synchronization may be required, where supported. +- data-active: similar to HSYNC and VSYNC, specifies data line polarity. +- field-even-active: field signal level during the even field data transmission. +- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock + signal. +- data-lanes: an array of physical data lane indexes. Position of an entry + determines the logical lane number, while the value of an entry indicates + physical lane, e.g. for 2-lane MIPI CSI-2 bus we could have + "data-lanes = <1 2>;", assuming the clock lane is on hardware lane 0. + This property is valid for serial busses only (e.g. MIPI CSI-2). +- clock-lanes: an array of physical clock lane indexes. Position of an entry + determines the logical lane number, while the value of an entry indicates + physical lane, e.g. for a MIPI CSI-2 bus we could have "clock-lanes = <0>;", + which places the clock lane on hardware lane 0. This property is valid for + serial busses only (e.g. MIPI CSI-2). Note that for the MIPI CSI-2 bus this + array contains only one entry. +- clock-noncontinuous: a boolean property to allow MIPI CSI-2 non-continuous + clock mode. + + +Example +------- + +The example snippet below describes two data pipelines. ov772x and imx074 are +camera sensors with a parallel and serial (MIPI CSI-2) video bus respectively. +Both sensors are on the I2C control bus corresponding to the i2c0 controller +node. ov772x sensor is linked directly to the ceu0 video host interface. +imx074 is linked to ceu0 through the MIPI CSI-2 receiver (csi2). ceu0 has a +(single) DMA engine writing captured data to memory. ceu0 node has a single +'port' node which may indicate that at any time only one of the following data +pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. + + ceu0: ceu@0xfe910000 { + compatible = "renesas,sh-mobile-ceu"; + reg = <0xfe910000 0xa0>; + interrupts = <0x880>; + + mclk: master_clock { + compatible = "renesas,ceu-clock"; + #clock-cells = <1>; + clock-frequency = <50000000>; /* Max clock frequency */ + clock-output-names = "mclk"; + }; + + port { + #address-cells = <1>; + #size-cells = <0>; + + /* Parallel bus endpoint */ + ceu0_1: endpoint@1 { + reg = <1>; /* Local endpoint # */ + remote = <&ov772x_1_1>; /* Remote phandle */ + bus-width = <8>; /* Used data lines */ + data-shift = <2>; /* Lines 9:2 are used */ + + /* If hsync-active/vsync-active are missing, + embedded BT.656 sync is used */ + hsync-active = <0>; /* Active low */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + + /* MIPI CSI-2 bus endpoint */ + ceu0_0: endpoint@0 { + reg = <0>; + remote = <&csi2_2>; + }; + }; + }; + + i2c0: i2c@0xfff20000 { + ... + ov772x_1: camera@0x21 { + compatible = "omnivision,ov772x"; + reg = <0x21>; + vddio-supply = <®ulator1>; + vddcore-supply = <®ulator2>; + + clock-frequency = <20000000>; + clocks = <&mclk 0>; + clock-names = "xclk"; + + port { + /* With 1 endpoint per port no need for addresses. */ + ov772x_1_1: endpoint { + bus-width = <8>; + remote-endpoint = <&ceu0_1>; + hsync-active = <1>; + vsync-active = <0>; /* Who came up with an + inverter here ?... */ + data-active = <1>; + pclk-sample = <1>; + }; + }; + }; + + imx074: camera@0x1a { + compatible = "sony,imx074"; + reg = <0x1a>; + vddio-supply = <®ulator1>; + vddcore-supply = <®ulator2>; + + clock-frequency = <30000000>; /* Shared clock with ov772x_1 */ + clocks = <&mclk 0>; + clock-names = "sysclk"; /* Assuming this is the + name in the datasheet */ + port { + imx074_1: endpoint { + clock-lanes = <0>; + data-lanes = <1 2>; + remote-endpoint = <&csi2_1>; + }; + }; + }; + }; + + csi2: csi2@0xffc90000 { + compatible = "renesas,sh-mobile-csi2"; + reg = <0xffc90000 0x1000>; + interrupts = <0x17a0>; + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + compatible = "renesas,csi2c"; /* One of CSI2I and CSI2C. */ + reg = <1>; /* CSI-2 PHY #1 of 2: PHY_S, + PHY_M has port address 0, + is unused. */ + csi2_1: endpoint { + clock-lanes = <0>; + data-lanes = <2 1>; + remote-endpoint = <&imx074_1>; + }; + }; + port@2 { + reg = <2>; /* port 2: link to the CEU */ + + csi2_2: endpoint { + remote-endpoint = <&ceu0_0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/metag/meta-intc.txt b/Documentation/devicetree/bindings/metag/meta-intc.txt index 8c47dcbfabc..80994adab39 100644 --- a/Documentation/devicetree/bindings/metag/meta-intc.txt +++ b/Documentation/devicetree/bindings/metag/meta-intc.txt @@ -12,7 +12,7 @@ Required properties: handle 32 interrupt sources). - interrupt-controller: The presence of this property identifies the node - as an interupt controller. No property value shall be defined. + as an interrupt controller. No property value shall be defined. - #interrupt-cells: Specifies the number of cells needed to encode an interrupt source. The type shall be a <u32> and the value shall be 2. diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index baf07987ae6..abd9e3cb2db 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -10,10 +10,40 @@ Optional properties: - fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used Sub-nodes: -- regulators : Contain the regulator nodes. The MC13892 regulators are - bound using their names as listed below with their registers and bits - for enabling. +- regulators : Contain the regulator nodes. The regulators are bound using + their names as listed below with their registers and bits for enabling. +MC13783 regulators: + sw1a : regulator SW1A (register 24, bit 0) + sw1b : regulator SW1B (register 25, bit 0) + sw2a : regulator SW2A (register 26, bit 0) + sw2b : regulator SW2B (register 27, bit 0) + sw3 : regulator SW3 (register 29, bit 20) + vaudio : regulator VAUDIO (register 32, bit 0) + viohi : regulator VIOHI (register 32, bit 3) + violo : regulator VIOLO (register 32, bit 6) + vdig : regulator VDIG (register 32, bit 9) + vgen : regulator VGEN (register 32, bit 12) + vrfdig : regulator VRFDIG (register 32, bit 15) + vrfref : regulator VRFREF (register 32, bit 18) + vrfcp : regulator VRFCP (register 32, bit 21) + vsim : regulator VSIM (register 33, bit 0) + vesim : regulator VESIM (register 33, bit 3) + vcam : regulator VCAM (register 33, bit 6) + vrfbg : regulator VRFBG (register 33, bit 9) + vvib : regulator VVIB (register 33, bit 11) + vrf1 : regulator VRF1 (register 33, bit 12) + vrf2 : regulator VRF2 (register 33, bit 15) + vmmc1 : regulator VMMC1 (register 33, bit 18) + vmmc2 : regulator VMMC2 (register 33, bit 21) + gpo1 : regulator GPO1 (register 34, bit 6) + gpo2 : regulator GPO2 (register 34, bit 8) + gpo3 : regulator GPO3 (register 34, bit 10) + gpo4 : regulator GPO4 (register 34, bit 12) + pwgt1spi : regulator PWGT1SPI (register 34, bit 15) + pwgt2spi : regulator PWGT2SPI (register 34, bit 16) + +MC13892 regulators: vcoincell : regulator VCOINCELL (register 13, bit 23) sw1 : regulator SW1 (register 24, bit 0) sw2 : regulator SW2 (register 25, bit 0) diff --git a/Documentation/devicetree/bindings/misc/sram.txt b/Documentation/devicetree/bindings/misc/sram.txt new file mode 100644 index 00000000000..4d0a00e453a --- /dev/null +++ b/Documentation/devicetree/bindings/misc/sram.txt @@ -0,0 +1,16 @@ +Generic on-chip SRAM + +Simple IO memory regions to be managed by the genalloc API. + +Required properties: + +- compatible : mmio-sram + +- reg : SRAM iomem address range + +Example: + +sram: sram@5c000000 { + compatible = "mmio-sram"; + reg = <0x5c000000 0x40000>; /* 256 KiB SRAM at address 0x5c000000 */ +}; diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt index bc50899e0c8..648d60eb9fd 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -1,6 +1,6 @@ * Atmel AT91 Pinmux Controller -The AT91 Pinmux Controler, enables the IC +The AT91 Pinmux Controller, enables the IC to share one PAD to several functional blocks. The sharing is done by multiplexing the PAD input/output signals. For each PAD there are up to 8 muxing options (called periph modes). Since different modules require diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt index 8edc20e1b09..2569866c692 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt @@ -5,7 +5,7 @@ controller, and pinmux/control device. Required properties: - compatible: "brcm,bcm2835-gpio" -- reg: Should contain the physical address of the GPIO module's registes. +- reg: Should contain the physical address of the GPIO module's registers. - gpio-controller: Marks the device node as a GPIO controller. - #gpio-cells : Should be two. The first cell is the pin number and the second cell is used to specify optional parameters: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt index 2c81e45f137..08f0c3d0157 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt @@ -1,7 +1,9 @@ One-register-per-pin type device tree based pinctrl driver Required properties: -- compatible : "pinctrl-single" +- compatible : "pinctrl-single" or "pinconf-single". + "pinctrl-single" means that pinconf isn't supported. + "pinconf-single" means that generic pinconf is supported. - reg : offset and length of the register set for the mux registers @@ -14,9 +16,61 @@ Optional properties: - pinctrl-single,function-off : function off mode for disabled state if available and same for all registers; if not specified, disabling of pin functions is ignored + - pinctrl-single,bit-per-mux : boolean to indicate that one register controls more than one pin +- pinctrl-single,drive-strength : array of value that are used to configure + drive strength in the pinmux register. They're value of drive strength + current and drive strength mask. + + /* drive strength current, mask */ + pinctrl-single,power-source = <0x30 0xf0>; + +- pinctrl-single,bias-pullup : array of value that are used to configure the + input bias pullup in the pinmux register. + + /* input, enabled pullup bits, disabled pullup bits, mask */ + pinctrl-single,bias-pullup = <0 1 0 1>; + +- pinctrl-single,bias-pulldown : array of value that are used to configure the + input bias pulldown in the pinmux register. + + /* input, enabled pulldown bits, disabled pulldown bits, mask */ + pinctrl-single,bias-pulldown = <2 2 0 2>; + + * Two bits to control input bias pullup and pulldown: User should use + pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means + pullup, and the other one bit means pulldown. + * Three bits to control input bias enable, pullup and pulldown. User should + use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias + enable bit should be included in pullup or pulldown bits. + * Although driver could set PIN_CONFIG_BIAS_DISABLE, there's no property as + pinctrl-single,bias-disable. Because pinctrl single driver could implement + it by calling pulldown, pullup disabled. + +- pinctrl-single,input-schmitt : array of value that are used to configure + input schmitt in the pinmux register. In some silicons, there're two input + schmitt value (rising-edge & falling-edge) in the pinmux register. + + /* input schmitt value, mask */ + pinctrl-single,input-schmitt = <0x30 0x70>; + +- pinctrl-single,input-schmitt-enable : array of value that are used to + configure input schmitt enable or disable in the pinmux register. + + /* input, enable bits, disable bits, mask */ + pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>; + +- pinctrl-single,gpio-range : list of value that are used to configure a GPIO + range. They're value of subnode phandle, pin base in pinctrl device, pin + number in this range, GPIO function value of this GPIO range. + The number of parameters is depend on #pinctrl-single,gpio-range-cells + property. + + /* pin base, nr pins & gpio function */ + pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>; + This driver assumes that there is only one register for each pin (unless the pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as specified in the pinctrl-bindings.txt document in this directory. @@ -42,6 +96,20 @@ Where 0xdc is the offset from the pinctrl register base address for the device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to be used when applying this change to the register. + +Optional sub-node: In case some pins could be configured as GPIO in the pinmux +register, those pins could be defined as a GPIO range. This sub-node is required +by pinctrl-single,gpio-range property. + +Required properties in sub-node: +- #pinctrl-single,gpio-range-cells : the number of parameters after phandle in + pinctrl-single,gpio-range property. + + range: gpio-range { + #pinctrl-single,gpio-range-cells = <3>; + }; + + Example: /* SoC common file */ @@ -58,7 +126,7 @@ pmx_core: pinmux@4a100040 { /* second controller instance for pins in wkup domain */ pmx_wkup: pinmux@4a31e040 { - compatible = "pinctrl-single; + compatible = "pinctrl-single"; reg = <0x4a31e040 0x0038>; #address-cells = <1>; #size-cells = <0>; @@ -76,6 +144,29 @@ control_devconf0: pinmux@48002274 { pinctrl-single,function-mask = <0x5F>; }; +/* third controller instance for pins in gpio domain */ +pmx_gpio: pinmux@d401e000 { + compatible = "pinconf-single"; + reg = <0xd401e000 0x0330>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <7>; + + /* sparse GPIO range could be supported */ + pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1 + &range 12 1 0 &range 13 29 1 + &range 43 1 0 &range 44 49 1 + &range 94 1 1 &range 96 2 1>; + + range: gpio-range { + #pinctrl-single,gpio-range-cells = <3>; + }; +}; + + /* board specific .dts file */ &pmx_core { @@ -96,6 +187,15 @@ control_devconf0: pinmux@48002274 { >; }; + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x208 0 /* UART0_RXD (IOCFG138) */ + 0x20c 0 /* UART0_TXD (IOCFG139) */ + >; + pinctrl-single,bias-pulldown = <0 2 2>; + pinctrl-single,bias-pullup = <0 1 1>; + }; + /* map uart2 pins */ uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < @@ -122,6 +222,11 @@ control_devconf0: pinmux@48002274 { }; +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; +}; + &uart2 { pinctrl-names = "default"; pinctrl-0 = <&uart2_pins>; diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index 4598a47aa0c..c70fca146e9 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -7,6 +7,7 @@ on-chip controllers onto these pads. Required Properties: - compatible: should be one of the following. + - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller, - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller. @@ -105,6 +106,8 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a - compatible: identifies the type of the external wakeup interrupt controller The possible values are: + - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller + found on Samsung S3C64xx SoCs, - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller found on Samsung Exynos4210 SoC. - interrupt-parent: phandle of the interrupt parent to which the external diff --git a/Documentation/devicetree/bindings/power_supply/power_supply.txt b/Documentation/devicetree/bindings/power_supply/power_supply.txt new file mode 100644 index 00000000000..8391bfa0eda --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/power_supply.txt @@ -0,0 +1,23 @@ +Power Supply Core Support + +Optional Properties: + - power-supplies : This property is added to a supply in order to list the + devices which supply it power, referenced by their phandles. + +Example: + + usb-charger: power@e { + compatible = "some,usb-charger"; + ... + }; + + ac-charger: power@c { + compatible = "some,ac-charger"; + ... + }; + + battery@b { + compatible = "some,battery"; + ... + power-supplies = <&usb-charger>, <&ac-charger>; + }; diff --git a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt index 9a599d27bd7..0347d8350d9 100644 --- a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt +++ b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt @@ -2,7 +2,7 @@ QNAP NAS devices have a microcontroller controlling the main power supply. This microcontroller is connected to UART1 of the Kirkwood and -Orion5x SoCs. Sending the charactor 'A', at 19200 baud, tells the +Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the microcontroller to turn the power off. This driver adds a handler to pm_power_off which is called to turn the power off. diff --git a/Documentation/devicetree/bindings/power_supply/tps65090.txt b/Documentation/devicetree/bindings/power_supply/tps65090.txt new file mode 100644 index 00000000000..8e5e0d3910d --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/tps65090.txt @@ -0,0 +1,17 @@ +TPS65090 Frontend PMU with Switchmode Charger + +Required Properties: +-compatible: "ti,tps65090-charger" + +Optional Properties: +-ti,enable-low-current-chrg: Enables charging when a low current is detected + while the default logic is to stop charging. + +This node is a subnode of the tps65090 PMIC. + +Example: + + tps65090-charger { + compatible = "ti,tps65090-charger"; + ti,enable-low-current-chrg; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8952.txt b/Documentation/devicetree/bindings/regulator/max8952.txt new file mode 100644 index 00000000000..866fcdd0f4e --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8952.txt @@ -0,0 +1,52 @@ +Maxim MAX8952 voltage regulator + +Required properties: +- compatible: must be equal to "maxim,max8952" +- reg: I2C slave address, usually 0x60 +- max8952,dvs-mode-microvolt: array of 4 integer values defining DVS voltages + in microvolts. All values must be from range <770000, 1400000> +- any required generic properties defined in regulator.txt + +Optional properties: +- max8952,vid-gpios: array of two GPIO pins used for DVS voltage selection +- max8952,en-gpio: GPIO used to control enable status of regulator +- max8952,default-mode: index of default DVS voltage, from <0, 3> range +- max8952,sync-freq: sync frequency, must be one of following values: + - 0: 26 MHz + - 1: 13 MHz + - 2: 19.2 MHz + Defaults to 26 MHz if not specified. +- max8952,ramp-speed: voltage ramp speed, must be one of following values: + - 0: 32mV/us + - 1: 16mV/us + - 2: 8mV/us + - 3: 4mV/us + - 4: 2mV/us + - 5: 1mV/us + - 6: 0.5mV/us + - 7: 0.25mV/us + Defaults to 32mV/us if not specified. +- any available generic properties defined in regulator.txt + +Example: + + vdd_arm_reg: pmic@60 { + compatible = "maxim,max8952"; + reg = <0x60>; + + /* max8952-specific properties */ + max8952,vid-gpios = <&gpx0 3 0>, <&gpx0 4 0>; + max8952,en-gpio = <&gpx0 1 0>; + max8952,default-mode = <0>; + max8952,dvs-mode-microvolt = <1250000>, <1200000>, + <1050000>, <950000>; + max8952,sync-freq = <0>; + max8952,ramp-speed = <0>; + + /* generic regulator properties */ + regulator-name = "vdd_arm"; + regulator-min-microvolt = <770000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt index 9fd69a18b0b..9e5e51d7886 100644 --- a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt @@ -28,7 +28,7 @@ Required properties: safe operating voltage). If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional - property is specified, then all the eigth voltage values for the + property is specified, then all the eight voltage values for the 'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified. Optional properties: diff --git a/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt b/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt new file mode 100644 index 00000000000..2a3feabd3b2 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt @@ -0,0 +1,15 @@ +Atmel AT91RM9200 Real Time Clock + +Required properties: +- compatible: should be: "atmel,at91rm9200-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: rtc alarm/event interrupt + +Example: + +rtc@fffffe00 { + compatible = "atmel,at91rm9200-rtc"; + reg = <0xfffffe00 0x100>; + interrupts = <1 4 7>; +}; diff --git a/Documentation/devicetree/bindings/serio/snps-arc_ps2.txt b/Documentation/devicetree/bindings/serio/snps-arc_ps2.txt new file mode 100644 index 00000000000..38c2f21e804 --- /dev/null +++ b/Documentation/devicetree/bindings/serio/snps-arc_ps2.txt @@ -0,0 +1,16 @@ +* ARC PS/2 driver: PS/2 block used in some ARC FPGA's & nSIM OSCI model + +Required properties: +- compatible : "snps,arc_ps2" +- reg : offset and length (always 0x14) of registers +- interrupts : interrupt +- interrupt-names : name of interrupt, must be "arc_ps2_irq" + +Example: + +serio@c9000400 { + compatible = "snps,arc_ps2"; + reg = <0xc9000400 0x14>; + interrupts = <13>; + interrupt-names = "arc_ps2_irq"; +} diff --git a/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt new file mode 100644 index 00000000000..8bf89c64364 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt @@ -0,0 +1,22 @@ +Broadcom BCM2835 SPI0 controller + +The BCM2835 contains two forms of SPI master controller, one known simply as +SPI0, and the other known as the "Universal SPI Master"; part of the +auxilliary block. This binding applies to the SPI0 controller. + +Required properties: +- compatible: Should be "brcm,bcm2835-spi". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks: The clock feeding the SPI controller. + +Example: + +spi@20204000 { + compatible = "brcm,bcm2835-spi"; + reg = <0x7e204000 0x1000>; + interrupts = <2 22>; + clocks = <&clk_spi>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt index 777abd7399d..b032dd76e9d 100644 --- a/Documentation/devicetree/bindings/spi/fsl-spi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -4,7 +4,7 @@ Required properties: - cell-index : QE SPI subblock index. 0: QE subblock SPI1 1: QE subblock SPI2 -- compatible : should be "fsl,spi". +- compatible : should be "fsl,spi" or "aeroflexgaisler,spictrl". - mode : the SPI operation mode, it can be "cpu" or "cpu-qe". - reg : Offset and length of the register set for the device - interrupts : <a b> where a is the interrupt number and b is a @@ -14,6 +14,7 @@ Required properties: controller you have. - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. +- clock-frequency : input clock frequency to non FSL_SOC cores Optional properties: - gpios : specifies the gpio pins to be used for chipselects. diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt new file mode 100644 index 00000000000..91ff771c7e7 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt @@ -0,0 +1,26 @@ +NVIDIA Tegra114 SPI controller. + +Required properties: +- compatible : should be "nvidia,tegra114-spi". +- reg: Should contain SPI registers location and length. +- interrupts: Should contain SPI interrupts. +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this SPI controller. +- This is also require clock named "spi" as per binding document + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt +Example: + +spi@7000d600 { + compatible = "nvidia,tegra114-spi"; + reg = <0x7000d600 0x200>; + interrupts = <0 82 0x04>; + nvidia,dma-request-selector = <&apbdma 16>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index a15ffeddfba..86aa061f069 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -31,9 +31,6 @@ Required Board Specific Properties: - #address-cells: should be 1. - #size-cells: should be 0. -- gpios: The gpio specifier for clock, mosi and miso interface lines (in the - order specified). The format of the gpio specifier depends on the gpio - controller. Optional Board Specific Properties: @@ -86,9 +83,8 @@ Example: spi_0: spi@12d20000 { #address-cells = <1>; #size-cells = <0>; - gpios = <&gpa2 4 2 3 0>, - <&gpa2 6 2 3 0>, - <&gpa2 7 2 3 0>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_bus>; w25q80bw@0 { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/staging/dwc2.txt b/Documentation/devicetree/bindings/staging/dwc2.txt new file mode 100644 index 00000000000..1a1b7cfa484 --- /dev/null +++ b/Documentation/devicetree/bindings/staging/dwc2.txt @@ -0,0 +1,15 @@ +Platform DesignWare HS OTG USB 2.0 controller +----------------------------------------------------- + +Required properties: +- compatible : "snps,dwc2" +- reg : Should contain 1 register range (address and length) +- interrupts : Should contain 1 interrupt + +Example: + + usb@101c0000 { + compatible = "ralink,rt3050-usb, snps,dwc2"; + reg = <0x101c0000 40000>; + interrupts = <18>; + }; diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt index 07654f0338b..8071ac20d4b 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt @@ -26,7 +26,7 @@ Required properties: - crtc: the crtc this display is connected to, see below Optional properties: - interface_pix_fmt: How this display is connected to the - crtc. Currently supported types: "rgb24", "rgb565" + crtc. Currently supported types: "rgb24", "rgb565", "bgr666" - edid: verbatim EDID data block describing attached display. - ddc: phandle describing the i2c bus handling the display data channel diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt index 8f01cb190f2..1928a3e83cd 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -33,6 +33,10 @@ Optional properties: RTAS and should not be registered. - no-loopback-test: set to indicate that the port does not implements loopback test mode +- fifo-size: the fifo size of the UART. +- auto-flow-control: one way to enable automatic flow control support. The + driver is allowed to detect support for the capability even without this + property. Example: diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt index 5778b9c83bd..1c04a4c9515 100644 --- a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt +++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt @@ -11,6 +11,7 @@ Optional properties: that indicate usb controller index - vbus-supply: regulator for vbus - disable-over-current: disable over current detect +- external-vbus-divider: enables off-chip resistor divider for Vbus Examples: usb@02184000 { /* USB OTG */ @@ -20,4 +21,5 @@ usb@02184000 { /* USB OTG */ fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; disable-over-current; + external-vbus-divider; }; diff --git a/Documentation/devicetree/bindings/usb/ehci-omap.txt b/Documentation/devicetree/bindings/usb/ehci-omap.txt new file mode 100644 index 00000000000..485a9a1efa7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-omap.txt @@ -0,0 +1,32 @@ +OMAP HS USB EHCI controller + +This device is usually the child of the omap-usb-host +Documentation/devicetree/bindings/mfd/omap-usb-host.txt + +Required properties: + +- compatible: should be "ti,ehci-omap" +- reg: should contain one register range i.e. start and length +- interrupts: description of the interrupt line + +Optional properties: + +- phys: list of phandles to PHY nodes. + This property is required if at least one of the ports are in + PHY mode i.e. OMAP_EHCI_PORT_MODE_PHY + +To specify the port mode, see +Documentation/devicetree/bindings/mfd/omap-usb-host.txt + +Example for OMAP4: + +usbhsehci: ehci@4a064c00 { + compatible = "ti,ehci-omap", "usb-ehci"; + reg = <0x4a064c00 0x400>; + interrupts = <0 77 0x4>; +}; + +&usbhsehci { + phys = <&hsusb1_phy 0 &hsusb3_phy>; +}; + diff --git a/Documentation/devicetree/bindings/usb/ohci-omap3.txt b/Documentation/devicetree/bindings/usb/ohci-omap3.txt new file mode 100644 index 00000000000..14ab42812a8 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-omap3.txt @@ -0,0 +1,15 @@ +OMAP HS USB OHCI controller (OMAP3 and later) + +Required properties: + +- compatible: should be "ti,ohci-omap3" +- reg: should contain one register range i.e. start and length +- interrupts: description of the interrupt line + +Example for OMAP4: + +usbhsohci: ohci@4a064800 { + compatible = "ti,ohci-omap3", "usb-ohci"; + reg = <0x4a064800 0x400>; + interrupts = <0 76 0x4>; +}; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 1ef0ce71f8f..662f0f1d231 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -8,10 +8,10 @@ OMAP MUSB GLUE and disconnect. - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - - num_eps : Specifies the number of endpoints. This is also a + - num-eps : Specifies the number of endpoints. This is also a MUSB configuration-specific setting. Should be set to "16" - - ram_bits : Specifies the ram address size. Should be set to "12" - - interface_type : This is a board specific setting to describe the type of + - ram-bits : Specifies the ram address size. Should be set to "12" + - interface-type : This is a board specific setting to describe the type of interface between the controller and the phy. It should be "0" or "1" specifying ULPI and UTMI respectively. - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" @@ -29,18 +29,46 @@ usb_otg_hs: usb_otg_hs@4a0ab000 { ti,hwmods = "usb_otg_hs"; ti,has-mailbox; multipoint = <1>; - num_eps = <16>; - ram_bits = <12>; + num-eps = <16>; + ram-bits = <12>; ctrl-module = <&omap_control_usb>; }; Board specific device node entry &usb_otg_hs { - interface_type = <1>; + interface-type = <1>; mode = <3>; power = <50>; }; +OMAP DWC3 GLUE + - compatible : Should be "ti,dwc3" + - ti,hwmods : Should be "usb_otg_ss" + - reg : Address and length of the register set for the device. + - interrupts : The irq number of this device that is used to interrupt the + MPU + - #address-cells, #size-cells : Must be present if the device has sub-nodes + - utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID. + It should be set to "1" for HW mode and "2" for SW mode. + - ranges: the child address space are mapped 1:1 onto the parent address space + +Sub-nodes: +The dwc3 core should be added as subnode to omap dwc3 glue. +- dwc3 : + The binding details of dwc3 can be found in: + Documentation/devicetree/bindings/usb/dwc3.txt + +omap_dwc3 { + compatible = "ti,dwc3"; + ti,hwmods = "usb_otg_ss"; + reg = <0x4a020000 0x1ff>; + interrupts = <0 93 4>; + #address-cells = <1>; + #size-cells = <1>; + utmi-mode = <2>; + ranges; +}; + OMAP CONTROL USB Required properties: diff --git a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt index 033194934f6..33fd3543f3f 100644 --- a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt +++ b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt @@ -1,20 +1,25 @@ -* Samsung's usb phy transceiver +SAMSUNG USB-PHY controllers -The Samsung's phy transceiver is used for controlling usb phy for -s3c-hsotg as well as ehci-s5p and ohci-exynos usb controllers -across Samsung SOCs. +** Samsung's usb 2.0 phy transceiver + +The Samsung's usb 2.0 phy transceiver is used for controlling +usb 2.0 phy for s3c-hsotg as well as ehci-s5p and ohci-exynos +usb controllers across Samsung SOCs. TODO: Adding the PHY binding with controller(s) according to the under -developement generic PHY driver. +development generic PHY driver. Required properties: Exynos4210: -- compatible : should be "samsung,exynos4210-usbphy" +- compatible : should be "samsung,exynos4210-usb2phy" - reg : base physical address of the phy registers and length of memory mapped region. +- clocks: Clock IDs array as required by the controller. +- clock-names: names of clock correseponding IDs clock property as requested + by the controller driver. Exynos5250: -- compatible : should be "samsung,exynos5250-usbphy" +- compatible : should be "samsung,exynos5250-usb2phy" - reg : base physical address of the phy registers and length of memory mapped region. @@ -44,12 +49,69 @@ Example: usbphy@125B0000 { #address-cells = <1>; #size-cells = <1>; - compatible = "samsung,exynos4210-usbphy"; + compatible = "samsung,exynos4210-usb2phy"; reg = <0x125B0000 0x100>; ranges; + clocks = <&clock 2>, <&clock 305>; + clock-names = "xusbxti", "otg"; + usbphy-sys { /* USB device and host PHY_CONTROL registers */ reg = <0x10020704 0x8>; }; }; + + +** Samsung's usb 3.0 phy transceiver + +Starting exynso5250, Samsung's SoC have usb 3.0 phy transceiver +which is used for controlling usb 3.0 phy for dwc3-exynos usb 3.0 +controllers across Samsung SOCs. + +Required properties: + +Exynos5250: +- compatible : should be "samsung,exynos5250-usb3phy" +- reg : base physical address of the phy registers and length of memory mapped + region. +- clocks: Clock IDs array as required by the controller. +- clock-names: names of clocks correseponding to IDs in the clock property + as requested by the controller driver. + +Optional properties: +- #address-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- #size-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- ranges: allows valid translation between child's address space and parent's + address space. + +- The child node 'usbphy-sys' to the node 'usbphy' is for the system controller + interface for usb-phy. It should provide the following information required by + usb-phy controller to control phy. + - reg : base physical address of PHY_CONTROL registers. + The size of this register is the total sum of size of all PHY_CONTROL + registers that the SoC has. For example, the size will be + '0x4' in case we have only one PHY_CONTROL register (e.g. + OTHERS register in S3C64XX or USB_PHY_CONTROL register in S5PV210) + and, '0x8' in case we have two PHY_CONTROL registers (e.g. + USBDEVICE_PHY_CONTROL and USBHOST_PHY_CONTROL registers in exynos4x). + and so on. + +Example: + usbphy@12100000 { + compatible = "samsung,exynos5250-usb3phy"; + reg = <0x12100000 0x100>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&clock 1>, <&clock 286>; + clock-names = "ext_xtal", "usbdrd30"; + + usbphy-sys { + /* USB device and host PHY_CONTROL registers */ + reg = <0x10040704 0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt new file mode 100644 index 00000000000..d7e272671c7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt @@ -0,0 +1,34 @@ +USB NOP PHY + +Required properties: +- compatible: should be usb-nop-xceiv + +Optional properties: +- clocks: phandle to the PHY clock. Use as per Documentation/devicetree + /bindings/clock/clock-bindings.txt + This property is required if clock-frequency is specified. + +- clock-names: Should be "main_clk" + +- clock-frequency: the clock frequency (in Hz) that the PHY clock must + be configured to. + +- vcc-supply: phandle to the regulator that provides RESET to the PHY. + +- reset-supply: phandle to the regulator that provides power to the PHY. + +Example: + + hsusb1_phy { + compatible = "usb-nop-xceiv"; + clock-frequency = <19200000>; + clocks = <&osc 0>; + clock-names = "main_clk"; + vcc-supply = <&hsusb1_vcc_regulator>; + reset-supply = <&hsusb1_reset_regulator>; + }; + +hsusb1_phy is a NOP USB PHY device that gets its clock from an oscillator +and expects that clock to be configured to 19.2MHz by the NOP PHY driver. +hsusb1_vcc_regulator provides power to the PHY and hsusb1_reset_regulator +controls RESET. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 19e1ef73ab0..4d1919bf233 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -5,6 +5,7 @@ using them to avoid name-space collisions. ad Avionic Design GmbH adi Analog Devices, Inc. +aeroflexgaisler Aeroflex Gaisler AB ak Asahi Kasei Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) apm Applied Micro Circuits Corporation (APM) @@ -48,6 +49,7 @@ samsung Samsung Semiconductor sbs Smart Battery System schindler Schindler sil Silicon Image +silabs Silicon Laboratories simtek sirf SiRF Technology, Inc. snps Synopsys, Inc. diff --git a/Documentation/devicetree/bindings/video/backlight/lp855x.txt b/Documentation/devicetree/bindings/video/backlight/lp855x.txt new file mode 100644 index 00000000000..1482103d288 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/lp855x.txt @@ -0,0 +1,41 @@ +lp855x bindings + +Required properties: + - compatible: "ti,lp8550", "ti,lp8551", "ti,lp8552", "ti,lp8553", + "ti,lp8556", "ti,lp8557" + - reg: I2C slave address (u8) + - dev-ctrl: Value of DEVICE CONTROL register (u8). It depends on the device. + +Optional properties: + - bl-name: Backlight device name (string) + - init-brt: Initial value of backlight brightness (u8) + - pwm-period: PWM period value. Set only PWM input mode used (u32) + - rom-addr: Register address of ROM area to be updated (u8) + - rom-val: Register value to be updated (u8) + +Example: + + /* LP8556 */ + backlight@2c { + compatible = "ti,lp8556"; + reg = <0x2c>; + + bl-name = "lcd-bl"; + dev-ctrl = /bits/ 8 <0x85>; + init-brt = /bits/ 8 <0x10>; + }; + + /* LP8557 */ + backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + + dev-ctrl = /bits/ 8 <0x41>; + init-brt = /bits/ 8 <0x0a>; + + /* 4V OV, 4 output LED string enabled */ + rom_14h { + rom-addr = /bits/ 8 <0x14>; + rom-val = /bits/ 8 <0xcf>; + }; + }; diff --git a/Documentation/devicetree/bindings/video/backlight/tps65217-backlight.txt b/Documentation/devicetree/bindings/video/backlight/tps65217-backlight.txt new file mode 100644 index 00000000000..5fb9279ac28 --- /dev/null +++ b/Documentation/devicetree/bindings/video/backlight/tps65217-backlight.txt @@ -0,0 +1,27 @@ +TPS65217 family of regulators + +The TPS65217 chip contains a boost converter and current sinks which can be +used to drive LEDs for use as backlights. + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- backlight: node for specifying WLED1 and WLED2 lines in TPS65217 +- isel: selection bit, valid values: 1 for ISEL1 (low-level) and 2 for ISEL2 (high-level) +- fdim: PWM dimming frequency, valid values: 100, 200, 500, 1000 +- default-brightness: valid values: 0-100 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + reg = <0x24>; + compatible = "ti,tps65217"; + backlight { + isel = <1>; /* 1 - ISET1, 2 ISET2 */ + fdim = <100>; /* TPS65217_BL_FDIM_100HZ */ + default-brightness = <50>; + }; + }; + diff --git a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt index c870b6478ec..2871e218a0f 100644 --- a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt +++ b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt @@ -5,58 +5,32 @@ Required properties: - compatible : "via,vt8500-fb" - reg : Should contain 1 register ranges(address and length) - interrupts : framebuffer controller interrupt -- display: a phandle pointing to the display node +- bits-per-pixel : bit depth of framebuffer (16 or 32) -Required nodes: -- display: a display node is required to initialize the lcd panel - This should be in the board dts. -- default-mode: a videomode within the display with timing parameters - as specified below. +Required subnodes: +- display-timings: see display-timing.txt for information Example: - fb@d800e400 { + fb@d8050800 { compatible = "via,vt8500-fb"; reg = <0xd800e400 0x400>; interrupts = <12>; - display = <&display>; - default-mode = <&mode0>; - }; - -VIA VT8500 Display ------------------------------------------------------ -Required properties (as per of_videomode_helper): - - - hactive, vactive: Display resolution - - hfront-porch, hback-porch, hsync-len: Horizontal Display timing parameters - in pixels - vfront-porch, vback-porch, vsync-len: Vertical display timing parameters in - lines - - clock: displayclock in Hz - - bpp: lcd panel bit-depth. - <16> for RGB565, <32> for RGB888 - -Optional properties (as per of_videomode_helper): - - width-mm, height-mm: Display dimensions in mm - - hsync-active-high (bool): Hsync pulse is active high - - vsync-active-high (bool): Vsync pulse is active high - - interlaced (bool): This is an interlaced mode - - doublescan (bool): This is a doublescan mode + bits-per-pixel = <16>; -Example: - display: display@0 { - modes { - mode0: mode@0 { + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ hactive = <800>; vactive = <480>; - hback-porch = <88>; hfront-porch = <40>; + hback-porch = <88>; hsync-len = <0>; vback-porch = <32>; vfront-porch = <11>; vsync-len = <1>; - clock = <0>; /* unused but required */ - bpp = <16>; /* non-standard but required */ }; }; }; + diff --git a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt index 3d325e1d11e..0bcadb2840a 100644 --- a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt +++ b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt @@ -4,20 +4,30 @@ Wondermedia WM8505 Framebuffer Required properties: - compatible : "wm,wm8505-fb" - reg : Should contain 1 register ranges(address and length) -- via,display: a phandle pointing to the display node +- bits-per-pixel : bit depth of framebuffer (16 or 32) -Required nodes: -- display: a display node is required to initialize the lcd panel - This should be in the board dts. See definition in - Documentation/devicetree/bindings/video/via,vt8500-fb.txt -- default-mode: a videomode node as specified in - Documentation/devicetree/bindings/video/via,vt8500-fb.txt +Required subnodes: +- display-timings: see display-timing.txt for information Example: - fb@d8050800 { + fb@d8051700 { compatible = "wm,wm8505-fb"; - reg = <0xd8050800 0x200>; - display = <&display>; - default-mode = <&mode0>; + reg = <0xd8051700 0x200>; + bits-per-pixel = <16>; + + display-timings { + native-mode = <&timing0>; + timing0: 800x480 { + clock-frequency = <0>; /* unused but required */ + hactive = <800>; + vactive = <480>; + hfront-porch = <40>; + hback-porch = <88>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; + }; + }; }; |