diff options
Diffstat (limited to 'Documentation/devicetree')
12 files changed, 246 insertions, 36 deletions
diff --git a/Documentation/devicetree/bindings/input/fsl-mma8450.txt b/Documentation/devicetree/bindings/input/fsl-mma8450.txt index a00c94ccbde..0b96e5737d3 100644 --- a/Documentation/devicetree/bindings/input/fsl-mma8450.txt +++ b/Documentation/devicetree/bindings/input/fsl-mma8450.txt @@ -2,6 +2,7 @@ Required properties: - compatible : "fsl,mma8450". +- reg: the I2C address of MMA8450 Example: diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index 19f6af47a79..baf07987ae6 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -46,8 +46,8 @@ Examples: ecspi@70010000 { /* ECSPI1 */ fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */ - <&gpio3 25 0>; /* GPIO4_25 */ + cs-gpios = <&gpio4 24 0>, /* GPIO4_24 */ + <&gpio4 25 0>; /* GPIO4_25 */ status = "okay"; pmic: mc13892@0 { diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index 645f5eaadb3..d2802d4717b 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -17,18 +17,46 @@ Required properties: device need to be present. The definition for each of these nodes is defined using the standard binding for regulators found at Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. - The valid names for regulators are: + The valid regulator-compatible values are: tps65910: vrtc, vio, vdd1, vdd2, vdd3, vdig1, vdig2, vpll, vdac, vaux1, vaux2, vaux33, vmmc tps65911: vrtc, vio, vdd1, vdd3, vddctrl, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8 +- xxx-supply: Input voltage supply regulator. + These entries are require if regulators are enabled for a device. Missing of these + properties can cause the regulator registration fails. + If some of input supply is powered through battery or always-on supply then + also it is require to have these parameters with proper node handle of always + on power supply. + tps65910: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: VAUX33 and VMMC input. + vcc4-supply: VAUX1 and VAUX2 input. + vcc5-supply: VPLL and VDAC input. + vcc6-supply: VDIG1 and VDIG2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + tps65911: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: LDO6, LDO7 and LDO8 input. + vcc4-supply: LDO5 input. + vcc5-supply: LDO3 and LDO4 input. + vcc6-supply: LDO1 and LDO2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + Optional properties: - ti,vmbch-threshold: (tps65911) main battery charged threshold comparator. (see VMBCH_VSEL in TPS65910 datasheet) - ti,vmbch2-threshold: (tps65911) main battery discharged threshold comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,en-ck32k-xtal: enable external 32-kHz crystal oscillator (see CK32K_CTRL + in TPS6591X datasheet) - ti,en-gpio-sleep: enable sleep control for gpios There should be 9 entries here, one for each gpio. @@ -56,74 +84,110 @@ Example: ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; + vcc1-supply = <®_parent>; + vcc2-supply = <&some_reg>; + vcc3-supply = <...>; + vcc4-supply = <...>; + vcc5-supply = <...>; + vcc6-supply = <...>; + vcc7-supply = <...>; + vccio-supply = <...>; + regulators { - vdd1_reg: vdd1 { + #address-cells = <1>; + #size-cells = <0>; + + vdd1_reg: regulator@0 { + regulator-compatible = "vdd1"; + reg = <0>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <0>; }; - vdd2_reg: vdd2 { + vdd2_reg: regulator@1 { + regulator-compatible = "vdd2"; + reg = <1>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <4>; }; - vddctrl_reg: vddctrl { + vddctrl_reg: regulator@2 { + regulator-compatible = "vddctrl"; + reg = <2>; regulator-min-microvolt = < 600000>; regulator-max-microvolt = <1400000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <0>; }; - vio_reg: vio { + vio_reg: regulator@3 { + regulator-compatible = "vio"; + reg = <3>; regulator-min-microvolt = <1500000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <1>; }; - ldo1_reg: ldo1 { + ldo1_reg: regulator@4 { + regulator-compatible = "ldo1"; + reg = <4>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo2_reg: ldo2 { + ldo2_reg: regulator@5 { + regulator-compatible = "ldo2"; + reg = <5>; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; ti,regulator-ext-sleep-control = <0>; }; - ldo3_reg: ldo3 { + ldo3_reg: regulator@6 { + regulator-compatible = "ldo3"; + reg = <6>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo4_reg: ldo4 { + ldo4_reg: regulator@7 { + regulator-compatible = "ldo4"; + reg = <7>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-always-on; ti,regulator-ext-sleep-control = <0>; }; - ldo5_reg: ldo5 { + ldo5_reg: regulator@8 { + regulator-compatible = "ldo5"; + reg = <8>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; ti,regulator-ext-sleep-control = <0>; }; - ldo6_reg: ldo6 { + ldo6_reg: regulator@9 { + regulator-compatible = "ldo6"; + reg = <9>; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; ti,regulator-ext-sleep-control = <0>; }; - ldo7_reg: ldo7 { + ldo7_reg: regulator@10 { + regulator-compatible = "ldo7"; + reg = <10>; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-always-on; regulator-boot-on; ti,regulator-ext-sleep-control = <1>; }; - ldo8_reg: ldo8 { + ldo8_reg: regulator@11 { + regulator-compatible = "ldo8"; + reg = <11>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <3300000>; regulator-always-on; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index c7e404b3ef0..fea541ee8b3 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -29,6 +29,6 @@ esdhc@70008000 { compatible = "fsl,imx51-esdhc"; reg = <0x70008000 0x4000>; interrupts = <2>; - cd-gpios = <&gpio0 6 0>; /* GPIO1_6 */ - wp-gpios = <&gpio0 5 0>; /* GPIO1_5 */ + cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */ + wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */ }; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index 7ab9e1a2d8b..4616fc28ee8 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -19,6 +19,6 @@ ethernet@83fec000 { reg = <0x83fec000 0x4000>; interrupts = <87>; phy-mode = "mii"; - phy-reset-gpios = <&gpio1 14 0>; /* GPIO2_14 */ + phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */ local-mac-address = [00 04 9F 01 1B B9]; }; diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt index 2f5b6b1ba15..4fae41d5479 100644 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt @@ -10,6 +10,7 @@ Optional properties: If this property is missing, the default assumed is Active low. - gpio-open-drain: GPIO is open drain type. If this property is missing then default assumption is false. +-vin-supply: Input supply name. Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. @@ -29,4 +30,5 @@ Example: enable-active-high; regulator-boot-on; gpio-open-drain; + vin-supply = <&parent_reg>; }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 5b7a408acda..66ece3f87bb 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -10,6 +10,11 @@ Optional properties: - regulator-always-on: boolean, regulator should never be disabled - regulator-boot-on: bootloader/firmware enabled regulator - <name>-supply: phandle to the parent supply/regulator node +- regulator-ramp-delay: ramp delay for regulator(in uV/uS) +- regulator-compatible: If a regulator chip contains multiple + regulators, and if the chip's binding contains a child node that + describes each regulator, then this property indicates which regulator + this child node is intended to configure. Example: diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt new file mode 100644 index 00000000000..0487e9675ba --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -0,0 +1,91 @@ +TPS65217 family of regulators + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- regulators: list of regulators provided by this controller, must be named + after their hardware counterparts: dcdc[1-3] and ldo[1-4] +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + + The valid names for regulators are: + tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + compatible = "ti,tps65217"; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + dcdc1_reg: regulator@0 { + reg = <0>; + regulator-compatible = "dcdc1"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + reg = <1>; + regulator-compatible = "dcdc2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + reg = <2>; + regulator-compatible = "dcdc3"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + reg = <3>; + regulator-compatible = "ldo1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + reg = <4>; + regulator-compatible = "ldo2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + reg = <5>; + regulator-compatible = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + reg = <6>; + regulator-compatible = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps6586x.txt b/Documentation/devicetree/bindings/regulator/tps6586x.txt index 0fcabaa3baa..d156e1b5db1 100644 --- a/Documentation/devicetree/bindings/regulator/tps6586x.txt +++ b/Documentation/devicetree/bindings/regulator/tps6586x.txt @@ -6,8 +6,17 @@ Required properties: - interrupts: the interrupt outputs of the controller - #gpio-cells: number of cells to describe a GPIO - gpio-controller: mark the device as a GPIO controller -- regulators: list of regulators provided by this controller, must be named - after their hardware counterparts: sm[0-2], ldo[0-9] and ldo_rtc +- regulators: list of regulators provided by this controller, must have + property "regulator-compatible" to match their hardware counterparts: + sm[0-2], ldo[0-9] and ldo_rtc +- sm0-supply: The input supply for the SM0. +- sm1-supply: The input supply for the SM1. +- sm2-supply: The input supply for the SM2. +- vinldo01-supply: The input supply for the LDO1 and LDO2 +- vinldo23-supply: The input supply for the LDO2 and LDO3 +- vinldo4-supply: The input supply for the LDO4 +- vinldo678-supply: The input supply for the LDO6, LDO7 and LDO8 +- vinldo9-supply: The input supply for the LDO9 Each regulator is defined using the standard binding for regulators. @@ -21,75 +30,113 @@ Example: #gpio-cells = <2>; gpio-controller; + sm0-supply = <&some_reg>; + sm1-supply = <&some_reg>; + sm2-supply = <&some_reg>; + vinldo01-supply = <...>; + vinldo23-supply = <...>; + vinldo4-supply = <...>; + vinldo678-supply = <...>; + vinldo9-supply = <...>; + regulators { - sm0_reg: sm0 { + #address-cells = <1>; + #size-cells = <0>; + + sm0_reg: regulator@0 { + reg = <0>; + regulator-compatible = "sm0"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm1_reg: sm1 { + sm1_reg: regulator@1 { + reg = <1>; + regulator-compatible = "sm1"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; regulator-boot-on; regulator-always-on; }; - sm2_reg: sm2 { + sm2_reg: regulator@2 { + reg = <2>; + regulator-compatible = "sm2"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <4550000>; regulator-boot-on; regulator-always-on; }; - ldo0_reg: ldo0 { + ldo0_reg: regulator@3 { + reg = <3>; + regulator-compatible = "ldo0"; regulator-name = "PCIE CLK"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; - ldo1_reg: ldo1 { + ldo1_reg: regulator@4 { + reg = <4>; + regulator-compatible = "ldo1"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo2_reg: ldo2 { + ldo2_reg: regulator@5 { + reg = <5>; + regulator-compatible = "ldo2"; regulator-min-microvolt = < 725000>; regulator-max-microvolt = <1500000>; }; - ldo3_reg: ldo3 { + ldo3_reg: regulator@6 { + reg = <6>; + regulator-compatible = "ldo3"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo4_reg: ldo4 { + ldo4_reg: regulator@7 { + reg = <7>; + regulator-compatible = "ldo4"; regulator-min-microvolt = <1700000>; regulator-max-microvolt = <2475000>; }; - ldo5_reg: ldo5 { + ldo5_reg: regulator@8 { + reg = <8>; + regulator-compatible = "ldo5"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo6_reg: ldo6 { + ldo6_reg: regulator@9 { + reg = <9>; + regulator-compatible = "ldo6"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo7_reg: ldo7 { + ldo7_reg: regulator@10 { + reg = <10>; + regulator-compatible = "ldo7"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo8_reg: ldo8 { + ldo8_reg: regulator@11 { + reg = <11>; + regulator-compatible = "ldo8"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; - ldo9_reg: ldo9 { + ldo9_reg: regulator@12 { + reg = <12>; + regulator-compatible = "ldo9"; regulator-min-microvolt = <1250000>; regulator-max-microvolt = <3300000>; }; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt index 0c3395d55ac..658749b90b9 100644 --- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -15,7 +15,6 @@ For twl6030 regulators/LDOs - "ti,twl6030-vusb" for VUSB LDO - "ti,twl6030-v1v8" for V1V8 LDO - "ti,twl6030-v2v1" for V2V1 LDO - - "ti,twl6030-clk32kg" for CLK32KG RESOURCE - "ti,twl6030-vdd1" for VDD1 SMPS - "ti,twl6030-vdd2" for VDD2 SMPS - "ti,twl6030-vdd3" for VDD3 SMPS diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 9841057d112..4256a6df9b7 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -17,6 +17,6 @@ ecspi@70010000 { reg = <0x70010000 0x4000>; interrupts = <36>; fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */ - <&gpio3 25 0>; /* GPIO4_25 */ + cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ + <&gpio3 25 0>; /* GPIO3_25 */ }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 6eab91747a8..db4d3af3643 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -3,6 +3,7 @@ Device tree binding vendor prefix registry. Keep list in alphabetical order. This isn't an exhaustive list, but you should add new prefixes to it before using them to avoid name-space collisions. +ad Avionic Design GmbH adi Analog Devices, Inc. amcc Applied Micro Circuits Corporation (APM, formally AMCC) apm Applied Micro Circuits Corporation (APM) |