diff options
Diffstat (limited to 'Documentation/devicetree')
59 files changed, 1194 insertions, 121 deletions
diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index d187e9f7cf1..1196290082d 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -7,6 +7,12 @@ PIT Timer required properties: - interrupts: Should contain interrupt for the PIT which is the IRQ line shared across all System Controller members. +System Timer (ST) required properties: +- compatible: Should be "atmel,at91rm9200-st" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt for the ST which is the IRQ line + shared across all System Controller members. + TC/TCLIB Timer required properties: - compatible: Should be "atmel,<chip>-tcb". <chip> can be "at91rm9200" or "at91sam9x5" diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt b/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt new file mode 100644 index 00000000000..fb7b5cd2652 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt @@ -0,0 +1,9 @@ +Broadcom BCM11351 device tree bindings +------------------------------------------- + +Boards with the bcm281xx SoC family (which includes bcm11130, bcm11140, +bcm11351, bcm28145, bcm28155 SoCs) shall have the following properties: + +Required root node property: + +compatible = "bcm,bcm11351"; diff --git a/Documentation/devicetree/bindings/arm/calxeda.txt b/Documentation/devicetree/bindings/arm/calxeda.txt index 4755caaccba..25fcf96795c 100644 --- a/Documentation/devicetree/bindings/arm/calxeda.txt +++ b/Documentation/devicetree/bindings/arm/calxeda.txt @@ -1,8 +1,15 @@ -Calxeda Highbank Platforms Device Tree Bindings +Calxeda Platforms Device Tree Bindings ----------------------------------------------- -Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following -properties. +Boards with Calxeda Cortex-A9 based ECX-1000 (Highbank) SOC shall have the +following properties. Required root node properties: - compatible = "calxeda,highbank"; + + +Boards with Calxeda Cortex-A15 based ECX-2000 SOC shall have the following +properties. + +Required root node properties: + - compatible = "calxeda,ecx-2000"; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt new file mode 100644 index 00000000000..f32494dbfe1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -0,0 +1,77 @@ +* ARM CPUs binding description + +The device tree allows to describe the layout of CPUs in a system through +the "cpus" node, which in turn contains a number of subnodes (ie "cpu") +defining properties for every cpu. + +Bindings for CPU nodes follow the ePAPR standard, available from: + +http://devicetree.org + +For the ARM architecture every CPU node must contain the following properties: + +- device_type: must be "cpu" +- reg: property matching the CPU MPIDR[23:0] register bits + reg[31:24] bits must be set to 0 +- compatible: should be one of: + "arm,arm1020" + "arm,arm1020e" + "arm,arm1022" + "arm,arm1026" + "arm,arm720" + "arm,arm740" + "arm,arm7tdmi" + "arm,arm920" + "arm,arm922" + "arm,arm925" + "arm,arm926" + "arm,arm940" + "arm,arm946" + "arm,arm9tdmi" + "arm,cortex-a5" + "arm,cortex-a7" + "arm,cortex-a8" + "arm,cortex-a9" + "arm,cortex-a15" + "arm,arm1136" + "arm,arm1156" + "arm,arm1176" + "arm,arm11mpcore" + "faraday,fa526" + "intel,sa110" + "intel,sa1100" + "marvell,feroceon" + "marvell,mohawk" + "marvell,xsc3" + "marvell,xscale" + +Example: + + cpus { + #size-cells = <0>; + #address-cells = <1>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x1>; + }; + + CPU2: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x100>; + }; + + CPU3: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x101>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt index e37241f1fdd..49fc7ada929 100644 --- a/Documentation/devicetree/bindings/arm/davinci/nand.txt +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt @@ -23,29 +23,16 @@ Recommended properties : - ti,davinci-nand-buswidth: buswidth 8 or 16 - ti,davinci-nand-use-bbt: use flash based bad block table support. -Example (enbw_cmc board): -aemif@60000000 { - compatible = "ti,davinci-aemif"; - #address-cells = <2>; - #size-cells = <1>; - reg = <0x68000000 0x80000>; - ranges = <2 0 0x60000000 0x02000000 - 3 0 0x62000000 0x02000000 - 4 0 0x64000000 0x02000000 - 5 0 0x66000000 0x02000000 - 6 0 0x68000000 0x02000000>; - nand@3,0 { - compatible = "ti,davinci-nand"; - reg = <3 0x0 0x807ff - 6 0x0 0x8000>; - #address-cells = <1>; - #size-cells = <1>; - ti,davinci-chipselect = <1>; - ti,davinci-mask-ale = <0>; - ti,davinci-mask-cle = <0>; - ti,davinci-mask-chipsel = <0>; - ti,davinci-ecc-mode = "hw"; - ti,davinci-ecc-bits = <4>; - ti,davinci-nand-use-bbt; - }; +Example(da850 EVM ): +nand_cs3@62000000 { + compatible = "ti,davinci-nand"; + reg = <0x62000000 0x807ff + 0x68000000 0x8000>; + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + ti,davinci-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + ti,davinci-nand-use-bbt; }; diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index 7ca52161e7a..7c3ee3aeb7b 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -37,7 +37,7 @@ L2: cache-controller { reg = <0xfff12000 0x1000>; arm,data-latency = <1 1 1>; arm,tag-latency = <2 2 2>; - arm,filter-latency = <0x80000000 0x8000000>; + arm,filter-ranges = <0x80000000 0x8000000>; cache-unified; cache-level = <2>; interrupts = <45>; diff --git a/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt new file mode 100644 index 00000000000..9cf3f25544c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt @@ -0,0 +1,50 @@ +ARM Versatile Express system registers +-------------------------------------- + +This is a system control registers block, providing multiple low level +platform functions like board detection and identification, software +interrupt generation, MMC and NOR Flash control etc. + +Required node properties: +- compatible value : = "arm,vexpress,sysreg"; +- reg : physical base address and the size of the registers window +- gpio-controller : specifies that the node is a GPIO controller +- #gpio-cells : size of the GPIO specifier, should be 2: + - first cell is the pseudo-GPIO line number: + 0 - MMC CARDIN + 1 - MMC WPROT + 2 - NOR FLASH WPn + - second cell can take standard GPIO flags (currently ignored). + +Example: + v2m_sysreg: sysreg@10000000 { + compatible = "arm,vexpress-sysreg"; + reg = <0x10000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + }; + +This block also can also act a bridge to the platform's configuration +bus via "system control" interface, addressing devices with site number, +position in the board stack, config controller, function and device +numbers - see motherboard's TRM for more details. + +The node describing a config device must refer to the sysreg node via +"arm,vexpress,config-bridge" phandle (can be also defined in the node's +parent) and relies on the board topology properties - see main vexpress +node documentation for more details. It must must also define the +following property: +- arm,vexpress-sysreg,func : must contain two cells: + - first cell defines function number (eg. 1 for clock generator, + 2 for voltage regulators etc.) + - device number (eg. osc 0, osc 1 etc.) + +Example: + mcc { + arm,vexpress,config-bridge = <&v2m_sysreg>; + + osc@0 { + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 0>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt index ec8b50cbb2e..ae49161e478 100644 --- a/Documentation/devicetree/bindings/arm/vexpress.txt +++ b/Documentation/devicetree/bindings/arm/vexpress.txt @@ -11,6 +11,10 @@ the motherboard file using a /include/ directive. As the motherboard can be initialized in one of two different configurations ("memory maps"), care must be taken to include the correct one. + +Root node +--------- + Required properties in the root node: - compatible value: compatible = "arm,vexpress,<model>", "arm,vexpress"; @@ -45,6 +49,10 @@ Optional properties in the root node: - Coretile Express A9x4 (V2P-CA9) HBI-0225: arm,hbi = <0x225>; + +CPU nodes +--------- + Top-level standard "cpus" node is required. It must contain a node with device_type = "cpu" property for every available core, eg.: @@ -59,6 +67,52 @@ with device_type = "cpu" property for every available core, eg.: }; }; + +Configuration infrastructure +---------------------------- + +The platform has an elaborated configuration system, consisting of +microcontrollers residing on the mother- and daughterboards known +as Motherboard/Daughterboard Configuration Controller (MCC and DCC). +The controllers are responsible for the platform initialization +(reset generation, flash programming, FPGA bitfiles loading etc.) +but also control clock generators, voltage regulators, gather +environmental data like temperature, power consumption etc. Even +the video output switch (FPGA) is controlled that way. + +Nodes describing devices controlled by this infrastructure should +point at the bridge device node: +- bridge phandle: + arm,vexpress,config-bridge = <phandle>; +This property can be also defined in a parent node (eg. for a DCC) +and is effective for all children. + + +Platform topology +----------------- + +As Versatile Express can be configured in number of physically +different setups, the device tree should describe platform topology. +Root node and main motherboard node must define the following +property, describing physical location of the children nodes: +- site number: + arm,vexpress,site = <number>; + where 0 means motherboard, 1 or 2 are daugtherboard sites, + 0xf means "master" site (site containing main CPU tile) +- when daughterboards are stacked on one site, their position + in the stack be be described with: + arm,vexpress,position = <number>; +- when describing tiles consisting more than one DCC, its number + can be described with: + arm,vexpress,dcc = <number>; + +Any of the numbers above defaults to zero if not defined in +the node or any of its parent. + + +Motherboard +----------- + The motherboard description file provides a single "motherboard" node using 2 address cells corresponding to the Static Memory Bus used between the motherboard and the tile. The first cell defines the Chip @@ -87,22 +141,30 @@ can be used to obtain required phandle in the tile's "aliases" node: - SP804 timers: v2m_timer01 and v2m_timer23 -Current Linux implementation requires a "arm,v2m_timer" alias -pointing at one of the motherboard's SP804 timers, if it is to be -used as the system timer. This alias should be defined in the -motherboard files. +The tile description should define a "smb" node, describing the +Static Memory Bus between the tile and motherboard. It must define +the following properties: +- "simple-bus" compatible value (to ensure creation of the children) + compatible = "simple-bus"; +- mapping of the SMB CS/offset addresses into main address space: + #address-cells = <2>; + #size-cells = <1>; + ranges = <...>; +- interrupts mapping: + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 63>; + interrupt-map = <...>; -The tile description must define "ranges", "interrupt-map-mask" and -"interrupt-map" properties to translate the motherboard's address -and interrupt space into one used by the tile's processor. -Abbreviated example: +Example of a VE tile description (simplified) +--------------------------------------------- /dts-v1/; / { model = "V2P-CA5s"; arm,hbi = <0x225>; + arm,vexpress,site = <0xf>; compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress"; interrupt-parent = <&gic>; #address-cells = <1>; @@ -134,13 +196,29 @@ Abbreviated example: <0x2c000100 0x100>; }; - motherboard { + dcc { + compatible = "simple-bus"; + arm,vexpress,config-bridge = <&v2m_sysreg>; + + osc@0 { + compatible = "arm,vexpress-osc"; + }; + }; + + smb { + compatible = "simple-bus"; + + #address-cells = <2>; + #size-cells = <1>; /* CS0 is visible at 0x08000000 */ ranges = <0 0 0x08000000 0x04000000>; + + #interrupt-cells = <1>; interrupt-map-mask = <0 0 63>; /* Active high IRQ 0 is connected to GIC's SPI0 */ interrupt-map = <0 0 0 &gic 0 0 4>; + + /include/ "vexpress-v2m-rs1.dtsi" }; }; -/include/ "vexpress-v2m-rs1.dtsi" diff --git a/Documentation/devicetree/bindings/clock/imx23-clock.txt b/Documentation/devicetree/bindings/clock/imx23-clock.txt index a0b867ef8d9..baadbb11fe9 100644 --- a/Documentation/devicetree/bindings/clock/imx23-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx23-clock.txt @@ -52,7 +52,7 @@ clocks and IDs. lcdif 38 etm 39 usb 40 - usb_pwr 41 + usb_phy 41 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx28-clock.txt b/Documentation/devicetree/bindings/clock/imx28-clock.txt index aa2af2866fe..52a49a4a50b 100644 --- a/Documentation/devicetree/bindings/clock/imx28-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx28-clock.txt @@ -73,8 +73,8 @@ clocks and IDs. can1 59 usb0 60 usb1 61 - usb0_pwr 62 - usb1_pwr 63 + usb0_phy 62 + usb1_phy 63 enet_out 64 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt new file mode 100644 index 00000000000..04ad47876be --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx5-clock.txt @@ -0,0 +1,191 @@ +* Clock bindings for Freescale i.MX5 + +Required properties: +- compatible: Should be "fsl,<soc>-ccm" , where <soc> can be imx51 or imx53 +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX5 +clocks and IDs. + + Clock ID + --------------------------- + dummy 0 + ckil 1 + osc 2 + ckih1 3 + ckih2 4 + ahb 5 + ipg 6 + axi_a 7 + axi_b 8 + uart_pred 9 + uart_root 10 + esdhc_a_pred 11 + esdhc_b_pred 12 + esdhc_c_s 13 + esdhc_d_s 14 + emi_sel 15 + emi_slow_podf 16 + nfc_podf 17 + ecspi_pred 18 + ecspi_podf 19 + usboh3_pred 20 + usboh3_podf 21 + usb_phy_pred 22 + usb_phy_podf 23 + cpu_podf 24 + di_pred 25 + tve_di 26 + tve_s 27 + uart1_ipg_gate 28 + uart1_per_gate 29 + uart2_ipg_gate 30 + uart2_per_gate 31 + uart3_ipg_gate 32 + uart3_per_gate 33 + i2c1_gate 34 + i2c2_gate 35 + gpt_ipg_gate 36 + pwm1_ipg_gate 37 + pwm1_hf_gate 38 + pwm2_ipg_gate 39 + pwm2_hf_gate 40 + gpt_hf_gate 41 + fec_gate 42 + usboh3_per_gate 43 + esdhc1_ipg_gate 44 + esdhc2_ipg_gate 45 + esdhc3_ipg_gate 46 + esdhc4_ipg_gate 47 + ssi1_ipg_gate 48 + ssi2_ipg_gate 49 + ssi3_ipg_gate 50 + ecspi1_ipg_gate 51 + ecspi1_per_gate 52 + ecspi2_ipg_gate 53 + ecspi2_per_gate 54 + cspi_ipg_gate 55 + sdma_gate 56 + emi_slow_gate 57 + ipu_s 58 + ipu_gate 59 + nfc_gate 60 + ipu_di1_gate 61 + vpu_s 62 + vpu_gate 63 + vpu_reference_gate 64 + uart4_ipg_gate 65 + uart4_per_gate 66 + uart5_ipg_gate 67 + uart5_per_gate 68 + tve_gate 69 + tve_pred 70 + esdhc1_per_gate 71 + esdhc2_per_gate 72 + esdhc3_per_gate 73 + esdhc4_per_gate 74 + usb_phy_gate 75 + hsi2c_gate 76 + mipi_hsc1_gate 77 + mipi_hsc2_gate 78 + mipi_esc_gate 79 + mipi_hsp_gate 80 + ldb_di1_div_3_5 81 + ldb_di1_div 82 + ldb_di0_div_3_5 83 + ldb_di0_div 84 + ldb_di1_gate 85 + can2_serial_gate 86 + can2_ipg_gate 87 + i2c3_gate 88 + lp_apm 89 + periph_apm 90 + main_bus 91 + ahb_max 92 + aips_tz1 93 + aips_tz2 94 + tmax1 95 + tmax2 96 + tmax3 97 + spba 98 + uart_sel 99 + esdhc_a_sel 100 + esdhc_b_sel 101 + esdhc_a_podf 102 + esdhc_b_podf 103 + ecspi_sel 104 + usboh3_sel 105 + usb_phy_sel 106 + iim_gate 107 + usboh3_gate 108 + emi_fast_gate 109 + ipu_di0_gate 110 + gpc_dvfs 111 + pll1_sw 112 + pll2_sw 113 + pll3_sw 114 + ipu_di0_sel 115 + ipu_di1_sel 116 + tve_ext_sel 117 + mx51_mipi 118 + pll4_sw 119 + ldb_di1_sel 120 + di_pll4_podf 121 + ldb_di0_sel 122 + ldb_di0_gate 123 + usb_phy1_gate 124 + usb_phy2_gate 125 + per_lp_apm 126 + per_pred1 127 + per_pred2 128 + per_podf 129 + per_root 130 + ssi_apm 131 + ssi1_root_sel 132 + ssi2_root_sel 133 + ssi3_root_sel 134 + ssi_ext1_sel 135 + ssi_ext2_sel 136 + ssi_ext1_com_sel 137 + ssi_ext2_com_sel 138 + ssi1_root_pred 139 + ssi1_root_podf 140 + ssi2_root_pred 141 + ssi2_root_podf 142 + ssi_ext1_pred 143 + ssi_ext1_podf 144 + ssi_ext2_pred 145 + ssi_ext2_podf 146 + ssi1_root_gate 147 + ssi2_root_gate 148 + ssi3_root_gate 149 + ssi_ext1_gate 150 + ssi_ext2_gate 151 + epit1_ipg_gate 152 + epit1_hf_gate 153 + epit2_ipg_gate 154 + epit2_hf_gate 155 + can_sel 156 + can1_serial_gate 157 + can1_ipg_gate 158 + +Examples (for mx53): + +clks: ccm@53fd4000{ + compatible = "fsl,imx53-ccm"; + reg = <0x53fd4000 0x4000>; + interrupts = <0 71 0x04 0 72 0x04>; + #clock-cells = <1>; +}; + +can1: can@53fc8000 { + compatible = "fsl,imx53-flexcan", "fsl,p1010-flexcan"; + reg = <0x53fc8000 0x4000>; + interrupts = <82>; + clocks = <&clks 158>, <&clks 157>; + clock-names = "ipg", "per"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index 492bd991d52..d77b4e68dc4 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -187,9 +187,9 @@ clocks and IDs. pll3_usb_otg 172 pll4_audio 173 pll5_video 174 - pll6_mlb 175 + pll8_mlb 175 pll7_usb_host 176 - pll8_enet 177 + pll6_enet 177 ssi1_ipg 178 ssi2_ipg 179 ssi3_ipg 180 @@ -198,6 +198,11 @@ clocks and IDs. usbphy2 183 ldb_di0_div_3_5 184 ldb_di1_div_3_5 185 + sata_ref 186 + sata_ref_100m 187 + pcie_ref 188 + pcie_ref_125m 189 + enet_ref 190 Examples: diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt new file mode 100644 index 00000000000..f3d44984d91 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt @@ -0,0 +1,42 @@ +SPEAr cpufreq driver +------------------- + +SPEAr SoC cpufreq driver for CPU frequency scaling. +It supports both uniprocessor (UP) and symmetric multiprocessor (SMP) systems +which share clock across all CPUs. + +Required properties: +- cpufreq_tbl: Table of frequencies CPU could be transitioned into, in the + increasing order. + +Optional properties: +- clock-latency: Specify the possible maximum transition latency for clock, in + unit of nanoseconds. + +Both required and optional properties listed above must be defined under node +/cpus/cpu@0. + +Examples: +-------- +cpus { + + <...> + + cpu@0 { + compatible = "arm,cortex-a9"; + reg = <0>; + + <...> + + cpufreq_tbl = < 166000 + 200000 + 250000 + 300000 + 400000 + 500000 + 600000 >; + }; + + <...> + +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt b/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt new file mode 100644 index 00000000000..a0e4cf88521 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt @@ -0,0 +1,18 @@ +STMPE gpio +---------- + +Required properties: + - compatible: "st,stmpe-gpio" + +Optional properties: + - st,norequest-mask: bitmask specifying which GPIOs should _not_ be requestable + due to different usage (e.g. touch, keypad) + +Node name must be stmpe_gpio and should be child node of stmpe node to which it +belongs. + +Example: + stmpe_gpio { + compatible = "st,stmpe-gpio"; + st,norequest-mask = <0x20>; //gpio 5 can't be used + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 4e16ba4feab..a33628759d3 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -75,4 +75,40 @@ Example of two SOC GPIO banks defined as gpio-controller nodes: gpio-controller; }; +2.1) gpio-controller and pinctrl subsystem +------------------------------------------ +gpio-controller on a SOC might be tightly coupled with the pinctrl +subsystem, in the sense that the pins can be used by other functions +together with optional gpio feature. + +While the pin allocation is totally managed by the pin ctrl subsystem, +gpio (under gpiolib) is still maintained by gpio drivers. It may happen +that different pin ranges in a SoC is managed by different gpio drivers. + +This makes it logical to let gpio drivers announce their pin ranges to +the pin ctrl subsystem and call 'pinctrl_request_gpio' in order to +request the corresponding pin before any gpio usage. + +For this, the gpio controller can use a pinctrl phandle and pins to +announce the pinrange to the pin ctrl subsystem. For example, + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + gpio-ranges = <&pinctrl1 20 10>, <&pinctrl2 50 20>; + + } + +where, + &pinctrl1 and &pinctrl2 is the phandle to the pinctrl DT node. + + Next values specify the base pin and number of pins for the range + handled by 'qe_pio_e' gpio. In the given example from base pin 20 to + pin 29 under pinctrl1 and pin 50 to pin 69 under pinctrl2 is handled + by this gpio controller. + +The pinctrl node must have "#gpio-range-cells" property to show number of +arguments to pass with phandle from gpio controllers node. diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt index 66efc804806..85f8c0d084f 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -9,6 +9,10 @@ Required properties: unused). - gpio-controller: Marks the device node as a GPIO controller. +optional properties: +- #gpio-lines: Number of gpio if absent 32. + + Example: pioA: gpio@fffff200 { compatible = "atmel,at91rm9200-gpio"; @@ -16,5 +20,6 @@ Example: interrupts = <2 4>; #gpio-cells = <2>; gpio-controller; + #gpio-lines = <19>; }; diff --git a/Documentation/devicetree/bindings/gpio/spear_spics.txt b/Documentation/devicetree/bindings/gpio/spear_spics.txt new file mode 100644 index 00000000000..96c37eb1507 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/spear_spics.txt @@ -0,0 +1,50 @@ +=== ST Microelectronics SPEAr SPI CS Driver === + +SPEAr platform provides a provision to control chipselects of ARM PL022 Prime +Cell spi controller through its system registers, which otherwise remains under +PL022 control. If chipselect remain under PL022 control then they would be +released as soon as transfer is over and TxFIFO becomes empty. This is not +desired by some of the device protocols above spi which expect (multiple) +transfers without releasing their chipselects. + +Chipselects can be controlled by software by turning them as GPIOs. SPEAr +provides another interface through system registers through which software can +directly control each PL022 chipselect. Hence, it is natural for SPEAr to export +the control of this interface as gpio. + +Required properties: + + * compatible: should be defined as "st,spear-spics-gpio" + * reg: mentioning address range of spics controller + * st-spics,peripcfg-reg: peripheral configuration register offset + * st-spics,sw-enable-bit: bit offset to enable sw control + * st-spics,cs-value-bit: bit offset to drive chipselect low or high + * st-spics,cs-enable-mask: chip select number bit mask + * st-spics,cs-enable-shift: chip select number program offset + * gpio-controller: Marks the device node as gpio controller + * #gpio-cells: should be 1 and will mention chip select number + +All the above bit offsets are within peripcfg register. + +Example: +------- +spics: spics@e0700000{ + compatible = "st,spear-spics-gpio"; + reg = <0xe0700000 0x1000>; + st-spics,peripcfg-reg = <0x3b0>; + st-spics,sw-enable-bit = <12>; + st-spics,cs-value-bit = <11>; + st-spics,cs-enable-mask = <3>; + st-spics,cs-enable-shift = <8>; + gpio-controller; + #gpio-cells = <2>; +}; + + +spi0: spi@e0100000 { + status = "okay"; + num-cs = <3>; + cs-gpios = <&gpio1 7 0>, <&spics 0>, + <&spics 1>; + ... +} diff --git a/Documentation/devicetree/bindings/i2c/atmel-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt index b689a0d9441..b689a0d9441 100644 --- a/Documentation/devicetree/bindings/i2c/atmel-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt diff --git a/Documentation/devicetree/bindings/i2c/davinci.txt b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt index 2dc935b4113..2dc935b4113 100644 --- a/Documentation/devicetree/bindings/i2c/davinci.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt diff --git a/Documentation/devicetree/bindings/i2c/gpio-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt index 4f8ec947c6b..4f8ec947c6b 100644 --- a/Documentation/devicetree/bindings/i2c/gpio-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt diff --git a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index 3614242e773..3614242e773 100644 --- a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt diff --git a/Documentation/devicetree/bindings/i2c/fsl-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt index 1eacd6b20ed..1eacd6b20ed 100644 --- a/Documentation/devicetree/bindings/i2c/fsl-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt diff --git a/Documentation/devicetree/bindings/i2c/mux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux.txt index af84cce5cd7..af84cce5cd7 100644 --- a/Documentation/devicetree/bindings/i2c/mux.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt new file mode 100644 index 00000000000..f46d928aa73 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt @@ -0,0 +1,18 @@ + +* Marvell MV64XXX I2C controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : Should be "marvell,mv64xxx-i2c" + - interrupts : The interrupt number + - clock-frequency : Desired I2C bus clock frequency in Hz. + +Examples: + + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/nomadik.txt b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt index 72065b0ff68..72065b0ff68 100644 --- a/Documentation/devicetree/bindings/i2c/nomadik.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt diff --git a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt index dced82ebe31..dced82ebe31 100644 --- a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt diff --git a/Documentation/devicetree/bindings/i2c/omap-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-omap.txt index 56564aa4b44..56564aa4b44 100644 --- a/Documentation/devicetree/bindings/i2c/omap-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-omap.txt diff --git a/Documentation/devicetree/bindings/i2c/pnx.txt b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt index fe98ada33ee..fe98ada33ee 100644 --- a/Documentation/devicetree/bindings/i2c/pnx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt diff --git a/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt index 569b1624851..569b1624851 100644 --- a/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt index 0f7945019f6..12b78ac507e 100644 --- a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt @@ -31,21 +31,3 @@ Examples: reg = <0xd4025000 0x1000>; interrupts = <58>; }; - -* Marvell MV64XXX I2C controller - -Required properties : - - - reg : Offset and length of the register set for the device - - compatible : Should be "marvell,mv64xxx-i2c" - - interrupts : The interrupt number - - clock-frequency : Desired I2C bus clock frequency in Hz. - -Examples: - - i2c@11000 { - compatible = "marvell,mv64xxx-i2c"; - reg = <0x11000 0x20>; - interrupts = <29>; - clock-frequency = <100000>; - }; diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index b6cb5a12c67..b6cb5a12c67 100644 --- a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt diff --git a/Documentation/devicetree/bindings/i2c/sirf-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt index 7baf9e133fa..7baf9e133fa 100644 --- a/Documentation/devicetree/bindings/i2c/sirf-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt diff --git a/Documentation/devicetree/bindings/i2c/arm-versatile.txt b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt index 361d31c51b6..361d31c51b6 100644 --- a/Documentation/devicetree/bindings/i2c/arm-versatile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt diff --git a/Documentation/devicetree/bindings/i2c/xiic.txt b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt index ceabbe91ae4..ceabbe91ae4 100644 --- a/Documentation/devicetree/bindings/i2c/xiic.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-ic.txt new file mode 100644 index 00000000000..7f9fb85f545 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-ic.txt @@ -0,0 +1,104 @@ +Allwinner Sunxi Interrupt Controller + +Required properties: + +- compatible : should be "allwinner,sunxi-ic" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + +The interrupt sources are as follows: + +0: ENMI +1: UART0 +2: UART1 +3: UART2 +4: UART3 +5: IR0 +6: IR1 +7: I2C0 +8: I2C1 +9: I2C2 +10: SPI0 +11: SPI1 +12: SPI2 +13: SPDIF +14: AC97 +15: TS +16: I2S +17: UART4 +18: UART5 +19: UART6 +20: UART7 +21: KEYPAD +22: TIMER0 +23: TIMER1 +24: TIMER2 +25: TIMER3 +26: CAN +27: DMA +28: PIO +29: TOUCH_PANEL +30: AUDIO_CODEC +31: LRADC +32: SDMC0 +33: SDMC1 +34: SDMC2 +35: SDMC3 +36: MEMSTICK +37: NAND +38: USB0 +39: USB1 +40: USB2 +41: SCR +42: CSI0 +43: CSI1 +44: LCDCTRL0 +45: LCDCTRL1 +46: MP +47: DEFEBE0 +48: DEFEBE1 +49: PMU +50: SPI3 +51: TZASC +52: PATA +53: VE +54: SS +55: EMAC +56: SATA +57: GPS +58: HDMI +59: TVE +60: ACE +61: TVD +62: PS2_0 +63: PS2_1 +64: USB3 +65: USB4 +66: PLE_PFM +67: TIMER4 +68: TIMER5 +69: GPU_GP +70: GPU_GPMMU +71: GPU_PP0 +72: GPU_PPMMU0 +73: GPU_PMU +74: GPU_RSV0 +75: GPU_RSV1 +76: GPU_RSV2 +77: GPU_RSV3 +78: GPU_RSV4 +79: GPU_RSV5 +80: GPU_RSV6 +82: SYNC_TIMER0 +83: SYNC_TIMER1 + +Example: + +intc: interrupt-controller { + compatible = "allwinner,sunxi-ic"; + reg = <0x01c20400 0x400>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt new file mode 100644 index 00000000000..2d88816dd55 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -0,0 +1,23 @@ +Common leds properties. + +Optional properties for child nodes: +- label : The label for this LED. If omitted, the label is + taken from the node name (excluding the unit address). + +- linux,default-trigger : This parameter, if present, is a + string defining the trigger assigned to the LED. Current triggers are: + "backlight" - LED will act as a back-light, controlled by the framebuffer + system + "default-on" - LED will turn on (but for leds-gpio see "default-state" + property in Documentation/devicetree/bindings/gpio/led.txt) + "heartbeat" - LED "double" flashes at a load average based rate + "ide-disk" - LED indicates disk activity + "timer" - LED flashes at a fixed, configurable rate + +Examples: + +system-status { + label = "Status"; + linux,default-trigger = "heartbeat"; + ... +}; diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index edc83c1c0d5..df1b3080f6b 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -10,16 +10,10 @@ LED sub-node properties: - gpios : Should specify the LED's GPIO, see "gpios property" in Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs should be indicated using flags in the GPIO specifier. -- label : (optional) The label for this LED. If omitted, the label is - taken from the node name (excluding the unit address). -- linux,default-trigger : (optional) This parameter, if present, is a - string defining the trigger assigned to the LED. Current triggers are: - "backlight" - LED will act as a back-light, controlled by the framebuffer - system - "default-on" - LED will turn on, but see "default-state" below - "heartbeat" - LED "double" flashes at a load average based rate - "ide-disk" - LED indicates disk activity - "timer" - LED flashes at a fixed, configurable rate +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt - default-state: (optional) The initial state of the LED. Valid values are "on", "off", and "keep". If the LED is already on or off and the default-state property is set the to same value, then no diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8e2e0ba2f48..a591c6741d7 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -21,6 +21,12 @@ Optional properties: - cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted - max-frequency: maximum operating clock frequency +- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on + this system, even if the controller claims it is. + +Optional SDIO properties: +- keep-power-in-suspend: Preserves card power during a suspend/resume cycle +- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion Example: @@ -33,4 +39,6 @@ sdhci@ab000000 { cd-inverted; wp-gpios = <&gpio 70 0>; max-frequency = <50000000>; + keep-power-in-suspend; + enable-sdio-wakeup; } diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 630a7d7f471..97e9e315400 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -12,10 +12,6 @@ is used. The Samsung's SDHCI controller bindings extends this as listed below. [A] The property "samsung,cd-pinmux-gpio" can be used as stated in the "Optional Board Specific Properties" section below. -[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property - is not specified, it is assumed that there is no card detection - mechanism used. - Required SoC Specific Properties: - compatible: should be one of the following - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci @@ -24,14 +20,18 @@ Required SoC Specific Properties: controller. Required Board Specific Properties: -- gpios: Should specify the gpios used for clock, command and data lines. The - gpio specifier format depends on the gpio controller. +- Samsung GPIO variant (will be completely replaced by pinctrl): + - gpios: Should specify the gpios used for clock, command and data lines. The + gpio specifier format depends on the gpio controller. +- Pinctrl variant (preferred if available): + - pinctrl-0: Should specify pin control groups used for this controller. + - pinctrl-names: Should contain only one value - "default". Optional Board Specific Properties: - samsung,cd-pinmux-gpio: Specifies the card detect line that is routed through a pinmux to the card-detect pin of the card slot. This property should be used only if none of the mmc core card-detect properties are - used. + used. Only for Samsung GPIO variant. Example: sdhci@12530000 { @@ -40,12 +40,18 @@ Example: interrupts = <0 75 0>; bus-width = <4>; cd-gpios = <&gpk2 2 2 3 3>; + + /* Samsung GPIO variant */ gpios = <&gpk2 0 2 0 3>, /* clock line */ <&gpk2 1 2 0 3>, /* command line */ <&gpk2 3 2 3 3>, /* data line 0 */ <&gpk2 4 2 3 3>, /* data line 1 */ <&gpk2 5 2 3 3>, /* data line 2 */ <&gpk2 6 2 3 3>; /* data line 3 */ + + /* Pinctrl variant */ + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>; + pinctrl-names = "default"; }; Note: This example shows both SoC specific and board specific properties diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index 06cd32d0805..06cd32d0805 100644 --- a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index be76a23b34c..ed271fc255b 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -19,6 +19,7 @@ ti,dual-volt: boolean, supports dual voltage cards "supply-name" examples are "vmmc", "vmmc_aux" etc ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence +ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed Example: mmc1: mmc@0x4809c000 { diff --git a/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt new file mode 100644 index 00000000000..d7fb6abb3eb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt @@ -0,0 +1,23 @@ +* Wondermedia WM8505/WM8650 SD/MMC Host Controller + +This file documents differences between the core properties described +by mmc.txt and the properties used by the wmt-sdmmc driver. + +Required properties: +- compatible: Should be "wm,wm8505-sdhc". +- interrupts: Two interrupts are required - regular irq and dma irq. + +Optional properties: +- sdon-inverted: SD_ON bit is inverted on the controller + +Examples: + +sdhc@d800a000 { + compatible = "wm,wm8505-sdhc"; + reg = <0xd800a000 0x1000>; + interrupts = <20 21>; + clocks = <&sdhc>; + bus-width = <4>; + sdon-inverted; +}; + diff --git a/Documentation/devicetree/bindings/net/can/grcan.txt b/Documentation/devicetree/bindings/net/can/grcan.txt new file mode 100644 index 00000000000..34ef3498f88 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/grcan.txt @@ -0,0 +1,28 @@ +Aeroflex Gaisler GRCAN and GRHCAN CAN controllers. + +The GRCAN and CRHCAN CAN controllers are available in the GRLIB VHDL IP core +library. + +Note: These properties are built from the AMBA plug&play in a Leon SPARC system +(the ordinary environment for GRCAN and GRHCAN). There are no dts files for +sparc. + +Required properties: + +- name : Should be "GAISLER_GRCAN", "01_03d", "GAISLER_GRHCAN" or "01_034" + +- reg : Address and length of the register set for the device + +- freq : Frequency of the external oscillator clock in Hz (the frequency of + the amba bus in the ordinary case) + +- interrupts : Interrupt number for this device + +Optional properties: + +- systemid : If not present or if the value of the least significant 16 bits + of this 32-bit property is smaller than GRCAN_TXBUG_SAFE_GRLIB_VERSION + a bug workaround is activated. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt new file mode 100644 index 00000000000..09055c2495f --- /dev/null +++ b/Documentation/devicetree/bindings/net/cdns-emac.txt @@ -0,0 +1,23 @@ +* Cadence EMAC Ethernet controller + +Required properties: +- compatible: Should be "cdns,[<chip>-]{emac}" + Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. + or the generic form: "cdns,emac". +- reg: Address and length of the register set for the device +- interrupts: Should contain macb interrupt +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "mii", "rmii". + +Optional properties: +- local-mac-address: 6 bytes, mac address + +Examples: + + macb0: ethernet@fffc4000 { + compatible = "cdns,at91rm9200-emac"; + reg = <0xfffc4000 0x4000>; + interrupts = <21>; + phy-mode = "rmii"; + local-mac-address = [3a 0e 03 04 05 06]; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index dcaabe9fe86..6ddd0286a9b 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -9,21 +9,15 @@ Required properties: number - interrupt-parent : The parent interrupt controller - cpdma_channels : Specifies number of channels in CPDMA -- host_port_no : Specifies host port shift -- cpdma_reg_ofs : Specifies CPDMA submodule register offset -- cpdma_sram_ofs : Specifies CPDMA SRAM offset -- ale_reg_ofs : Specifies ALE submodule register offset - ale_entries : Specifies No of entries ALE can hold -- host_port_reg_ofs : Specifies host port register offset -- hw_stats_reg_ofs : Specifies hardware statistics register offset -- bd_ram_ofs : Specifies internal desciptor RAM offset - bd_ram_size : Specifies internal descriptor RAM size - rx_descs : Specifies number of Rx descriptors - mac_control : Specifies Default MAC control register content for the specific platform - slaves : Specifies number for slaves -- slave_reg_ofs : Specifies slave register offset -- sliver_reg_ofs : Specifies slave sliver register offset +- cpts_active_slave : Specifies the slave to use for time stamping +- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds +- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds - phy_id : Specifies slave phy id - mac-address : Specifies slave MAC address @@ -45,30 +39,22 @@ Examples: interrupts = <55 0x4>; interrupt-parent = <&intc>; cpdma_channels = <8>; - host_port_no = <0>; - cpdma_reg_ofs = <0x800>; - cpdma_sram_ofs = <0xa00>; - ale_reg_ofs = <0xd00>; ale_entries = <1024>; - host_port_reg_ofs = <0x108>; - hw_stats_reg_ofs = <0x900>; - bd_ram_ofs = <0x2000>; bd_ram_size = <0x2000>; no_bd_ram = <0>; rx_descs = <64>; mac_control = <0x20>; slaves = <2>; + cpts_active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; cpsw_emac0: slave@0 { - slave_reg_ofs = <0x208>; - sliver_reg_ofs = <0xd80>; - phy_id = "davinci_mdio.16:00"; + phy_id = <&davinci_mdio>, <0>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { - slave_reg_ofs = <0x308>; - sliver_reg_ofs = <0xdc0>; - phy_id = "davinci_mdio.16:01"; + phy_id = <&davinci_mdio>, <1>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; @@ -79,30 +65,22 @@ Examples: compatible = "ti,cpsw"; ti,hwmods = "cpgmac0"; cpdma_channels = <8>; - host_port_no = <0>; - cpdma_reg_ofs = <0x800>; - cpdma_sram_ofs = <0xa00>; - ale_reg_ofs = <0xd00>; ale_entries = <1024>; - host_port_reg_ofs = <0x108>; - hw_stats_reg_ofs = <0x900>; - bd_ram_ofs = <0x2000>; bd_ram_size = <0x2000>; no_bd_ram = <0>; rx_descs = <64>; mac_control = <0x20>; slaves = <2>; + cpts_active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; cpsw_emac0: slave@0 { - slave_reg_ofs = <0x208>; - sliver_reg_ofs = <0xd80>; - phy_id = "davinci_mdio.16:00"; + phy_id = <&davinci_mdio>, <0>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { - slave_reg_ofs = <0x308>; - sliver_reg_ofs = <0xdc0>; - phy_id = "davinci_mdio.16:01"; + phy_id = <&davinci_mdio>, <1>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt new file mode 100644 index 00000000000..3a268127b05 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -0,0 +1,141 @@ +* Atmel AT91 Pinmux Controller + +The AT91 Pinmux Controler, enables the IC +to share one PAD to several functional blocks. The sharing is done by +multiplexing the PAD input/output signals. For each PAD there are up to +8 muxing options (called periph modes). Since different modules require +different PAD settings (like pull up, keeper, etc) the contoller controls +also the PAD settings parameters. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Atmel AT91 pin configuration node is a node of a group of pins which can be +used for a specific device or function. This node represents both mux and config +of the pins in that group. The 'pins' selects the function mode(also named pin +mode) this pin can work on and the 'config' configures various pad settings +such as pull-up, multi drive, etc. + +Required properties for iomux controller: +- compatible: "atmel,at91rm9200-pinctrl" +- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be + configured in this periph mode. All the periph and bank need to be describe. + +How to create such array: + +Each column will represent the possible peripheral of the pinctrl +Each line will represent a pio bank + +Take an example on the 9260 +Peripheral: 2 ( A and B) +Bank: 3 (A, B and C) +=> + + /* A B */ + 0xffffffff 0xffc00c3b /* pioA */ + 0xffffffff 0x7fff3ccf /* pioB */ + 0xffffffff 0x007fffff /* pioC */ + +For each peripheral/bank we will descibe in a u32 if a pin can can be +configured in it by putting 1 to the pin bit (1 << pin) + +Let's take the pioA on peripheral B +From the datasheet Table 10-2. +Peripheral B +PA0 MCDB0 +PA1 MCCDB +PA2 +PA3 MCDB3 +PA4 MCDB2 +PA5 MCDB1 +PA6 +PA7 +PA8 +PA9 +PA10 ETX2 +PA11 ETX3 +PA12 +PA13 +PA14 +PA15 +PA16 +PA17 +PA18 +PA19 +PA20 +PA21 +PA22 ETXER +PA23 ETX2 +PA24 ETX3 +PA25 ERX2 +PA26 ERX3 +PA27 ERXCK +PA28 ECRS +PA29 ECOL +PA30 RXD4 +PA31 TXD4 + +=> 0xffc00c3b + +Required properties for pin configuration node: +- atmel,pins: 4 integers array, represents a group of pins mux and config + setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>. + The PERIPH 0 means gpio. + +Bits used for CONFIG: +PULL_UP (1 << 0): indicate this pin need a pull up. +MULTIDRIVE (1 << 1): indicate this pin need to be configured as multidrive. +DEGLITCH (1 << 2): indicate this pin need deglitch. +PULL_DOWN (1 << 3): indicate this pin need a pull down. +DIS_SCHMIT (1 << 4): indicate this pin need to disable schmit trigger. +DEBOUNCE (1 << 16): indicate this pin need debounce. +DEBOUNCE_VAL (0x3fff << 17): debounce val. + +NOTE: +Some requirements for using atmel,at91rm9200-pinctrl binding: +1. We have pin function node defined under at91 controller node to represent + what pinmux functions this SoC supports. +2. The driver can use the function node's name and pin configuration node's + name describe the pin function and group hierarchy. + For example, Linux at91 pinctrl driver takes the function node's name + as the function name and pin configuration node's name as group name to + create the map table. +3. Each pin configuration node should have a phandle, devices can set pins + configurations by referring to the phandle of that pin configuration node. +4. The gpio controller must be describe in the pinctrl simple-bus. + +Examples: + +pinctrl@fffff400 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; + reg = <0xfffff400 0x600>; + + atmel,mux-mask = < + /* A B */ + 0xffffffff 0xffc00c3b /* pioA */ + 0xffffffff 0x7fff3ccf /* pioB */ + 0xffffffff 0x007fffff /* pioC */ + >; + + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <1 14 0x1 0x0 /* PB14 periph A */ + 1 15 0x1 0x1>; /* PB15 periph with pullup */ + }; + }; +}; + +dbgu: serial@fffff200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffff200 0x200>; + interrupts = <1 4 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt new file mode 100644 index 00000000000..93f45e9dce7 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt @@ -0,0 +1,19 @@ +NVIDIA Tegra20 real-time clock + +The Tegra RTC maintains seconds and milliseconds counters, and five alarm +registers. The alarms and other interrupts may wake the system from low-power +state. + +Required properties: + +- compatible : should be "nvidia,tegra20-rtc". +- reg : Specifies base physical address and size of the registers. +- interrupts : A single interrupt specifier. + +Example: + +timer { + compatible = "nvidia,tegra20-rtc"; + reg = <0x7000e000 0x100>; + interrupts = <0 2 0x04>; +}; diff --git a/Documentation/devicetree/bindings/rtc/orion-rtc.txt b/Documentation/devicetree/bindings/rtc/orion-rtc.txt new file mode 100644 index 00000000000..3bf63ffa516 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/orion-rtc.txt @@ -0,0 +1,18 @@ +* Mvebu Real Time Clock + +RTC controller for the Kirkwood, the Dove, the Armada 370 and the +Armada XP SoCs + +Required properties: +- compatible : Should be "marvell,orion-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: IRQ line for the RTC. + +Example: + +rtc@10300 { + compatible = "marvell,orion-rtc"; + reg = <0xd0010300 0x20>; + interrupts = <50>; +}; diff --git a/Documentation/devicetree/bindings/thermal/db8500-thermal.txt b/Documentation/devicetree/bindings/thermal/db8500-thermal.txt new file mode 100644 index 00000000000..2e1c06fad81 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/db8500-thermal.txt @@ -0,0 +1,44 @@ +* ST-Ericsson DB8500 Thermal + +** Thermal node properties: + +- compatible : "stericsson,db8500-thermal"; +- reg : address range of the thermal sensor registers; +- interrupts : interrupts generated from PRCMU; +- interrupt-names : "IRQ_HOTMON_LOW" and "IRQ_HOTMON_HIGH"; +- num-trips : number of total trip points, this is required, set it 0 if none, + if greater than 0, the following properties must be defined; +- tripN-temp : temperature of trip point N, should be in ascending order; +- tripN-type : type of trip point N, should be one of "active" "passive" "hot" + "critical"; +- tripN-cdev-num : number of the cooling devices which can be bound to trip + point N, this is required if trip point N is defined, set it 0 if none, + otherwise the following cooling device names must be defined; +- tripN-cdev-nameM : name of the No. M cooling device of trip point N; + +Usually the num-trips and tripN-*** are separated in board related dts files. + +Example: +thermal@801573c0 { + compatible = "stericsson,db8500-thermal"; + reg = <0x801573c0 0x40>; + interrupts = <21 0x4>, <22 0x4>; + interrupt-names = "IRQ_HOTMON_LOW", "IRQ_HOTMON_HIGH"; + + num-trips = <3>; + + trip0-temp = <75000>; + trip0-type = "active"; + trip0-cdev-num = <1>; + trip0-cdev-name0 = "thermal-cpufreq-0"; + + trip1-temp = <80000>; + trip1-type = "active"; + trip1-cdev-num = <2>; + trip1-cdev-name0 = "thermal-cpufreq-0"; + trip1-cdev-name1 = "thermal-fan"; + + trip2-temp = <85000>; + trip2-type = "critical"; + trip2-cdev-num = <0>; +} diff --git a/Documentation/devicetree/bindings/timer/allwinner,sunxi-timer.txt b/Documentation/devicetree/bindings/timer/allwinner,sunxi-timer.txt new file mode 100644 index 00000000000..0c7b64e95a6 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/allwinner,sunxi-timer.txt @@ -0,0 +1,17 @@ +Allwinner A1X SoCs Timer Controller + +Required properties: + +- compatible : should be "allwinner,sunxi-timer" +- reg : Specifies base physical address and size of the registers. +- interrupts : The interrupt of the first timer +- clocks: phandle to the source clock (usually a 24 MHz fixed clock) + +Example: + +timer { + compatible = "allwinner,sunxi-timer"; + reg = <0x01c20c00 0x400>; + interrupts = <22>; + clocks = <&osc>; +}; diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt new file mode 100644 index 00000000000..e019fdc3877 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt @@ -0,0 +1,21 @@ +NVIDIA Tegra20 timer + +The Tegra20 timer provides four 29-bit timer channels and a single 32-bit free +running counter. The first two channels may also trigger a watchdog reset. + +Required properties: + +- compatible : should be "nvidia,tegra20-timer". +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 4 interrupts; one per timer channel. + +Example: + +timer { + compatible = "nvidia,tegra20-timer"; + reg = <0x60005000 0x60>; + interrupts = <0 0 0x04 + 0 1 0x04 + 0 41 0x04 + 0 42 0x04>; +}; diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt new file mode 100644 index 00000000000..906109d4c59 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt @@ -0,0 +1,23 @@ +NVIDIA Tegra30 timer + +The Tegra30 timer provides ten 29-bit timer channels, a single 32-bit free +running counter, and 5 watchdog modules. The first two channels may also +trigger a legacy watchdog reset. + +Required properties: + +- compatible : should be "nvidia,tegra30-timer", "nvidia,tegra20-timer". +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 6 interrupts; one per each of timer channels 1 + through 5, and one for the shared interrupt for the remaining channels. + +timer { + compatible = "nvidia,tegra30-timer", "nvidia,tegra20-timer"; + reg = <0x60005000 0x400>; + interrupts = <0 0 0x04 + 0 1 0x04 + 0 41 0x04 + 0 42 0x04 + 0 121 0x04 + 0 122 0x04>; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt index 2ee903fad25..273a8d5b330 100644 --- a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt +++ b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt @@ -6,11 +6,19 @@ Required properties: - reg : Address and length of the register set for the device - interrupts : Should contain the auart interrupt numbers +Optional properties: +- fsl,auart-dma-channel : The DMA channels, the first is for RX, the other + is for TX. If you add this property, it also means that you + will enable the DMA support for the auart. + Note: due to the hardware bug in imx23(see errata : 2836), + only the imx28 can enable the DMA support for the auart. + Example: auart0: serial@8006a000 { compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006a000 0x2000>; interrupts = <112 70 71>; + fsl,auart-dma-channel = <8 9>; }; Note: Each auart port should have an alias correctly numbered in "aliases" diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt index ba385f2e0dd..1e1145ca4f3 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -14,7 +14,10 @@ Required properties: - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. -- clock-frequency : the input clock frequency for the UART. +- clock-frequency : the input clock frequency for the UART + or + clocks phandle to refer to the clk used as per Documentation/devicetree + /bindings/clock/clock-bindings.txt Optional properties: - current-speed : the current active speed of the UART. diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt index 707c1a2dae0..ea840f7f925 100644 --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -5,12 +5,12 @@ AM33XX MUSB GLUE - ti,hwmods : must be "usb_otg_hs" - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - - num_eps : Specifies the number of endpoints. This is also a + - num-eps : Specifies the number of endpoints. This is also a MUSB configuration-specific setting. Should be set to "16" - - ram_bits : Specifies the ram address size. Should be set to "12" - - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + - ram-bits : Specifies the ram address size. Should be set to "12" + - port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2" represents PERIPHERAL. - - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2" + - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2" represents PERIPHERAL. - power : Should be "250". This signifies the controller can supply upto 500mA when operating in host mode. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ac2c2c416a1..902b1b1f568 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -5,6 +5,7 @@ using them to avoid name-space collisions. ad Avionic Design GmbH adi Analog Devices, Inc. +ak Asahi Kasei Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. @@ -25,6 +26,7 @@ gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. hp Hewlett Packard ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. +img Imagination Technologies Ltd. intercontrol Inter Control Group linux Linux-specific binding marvell Marvell Technology Group Ltd. @@ -34,8 +36,9 @@ national National Semiconductor nintendo Nintendo nvidia NVIDIA nxp NXP Semiconductors +onnn ON Semiconductor Corp. picochip Picochip Ltd -powervr Imagination Technologies +powervr PowerVR (deprecated, use img) qcom Qualcomm, Inc. ramtron Ramtron International realtek Realtek Semiconductor Corp. @@ -45,6 +48,7 @@ schindler Schindler sil Silicon Image simtek sirf SiRF Technology, Inc. +snps Synopsys, Inc. st STMicroelectronics stericsson ST-Ericsson ti Texas Instruments diff --git a/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt new file mode 100644 index 00000000000..d209366b4a6 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt @@ -0,0 +1,13 @@ +BCM2835 Watchdog timer + +Required properties: + +- compatible : should be "brcm,bcm2835-pm-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +watchdog { + compatible = "brcm,bcm2835-pm-wdt"; + reg = <0x7e100000 0x28>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt new file mode 100644 index 00000000000..0b271777560 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt @@ -0,0 +1,13 @@ +Allwinner sunXi Watchdog timer + +Required properties: + +- compatible : should be "allwinner,sunxi-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +wdt: watchdog@01c20c90 { + compatible = "allwinner,sunxi-wdt"; + reg = <0x01c20c90 0x10>; +}; diff --git a/Documentation/devicetree/usage-model.txt b/Documentation/devicetree/usage-model.txt index dca90fe22a9..ef9d06c9f8f 100644 --- a/Documentation/devicetree/usage-model.txt +++ b/Documentation/devicetree/usage-model.txt @@ -347,7 +347,7 @@ later), which will happily live at the base of the Linux /sys/devices tree. Therefore, if a DT node is at the root of the tree, then it really probably is best registered as a platform_device. -Linux board support code calls of_platform_populate(NULL, NULL, NULL) +Linux board support code calls of_platform_populate(NULL, NULL, NULL, NULL) to kick off discovery of devices at the root of the tree. The parameters are all NULL because when starting from the root of the tree, there is no need to provide a starting node (the first NULL), a |