diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/emc2103 | 33 | ||||
| -rw-r--r-- | Documentation/hwmon/ltc4245 | 24 | ||||
| -rw-r--r-- | Documentation/hwmon/pc87427 | 27 | ||||
| -rw-r--r-- | Documentation/hwmon/sysfs-interface | 29 | ||||
| -rw-r--r-- | Documentation/hwmon/w83627ehf | 15 |
5 files changed, 114 insertions, 14 deletions
diff --git a/Documentation/hwmon/emc2103 b/Documentation/hwmon/emc2103 new file mode 100644 index 00000000000..a12b2c12714 --- /dev/null +++ b/Documentation/hwmon/emc2103 @@ -0,0 +1,33 @@ +Kernel driver emc2103 +====================== + +Supported chips: + * SMSC EMC2103 + Addresses scanned: I2C 0x2e + Prefix: 'emc2103' + Datasheet: Not public + +Authors: + Steve Glendinning <steve.glendinning@smsc.com> + +Description +----------- + +The Standard Microsystems Corporation (SMSC) EMC2103 chips +contain up to 4 temperature sensors and a single fan controller. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. Fan +readings can be divided by a programmable divider (1, 2, 4 or 8) to give +the readings more range or accuracy. Not all RPM values can accurately be +represented, so some rounding is done. With a divider of 1, the lowest +representable value is 480 RPM. + +This driver supports RPM based control, to use this a fan target +should be written to fan1_target and pwm1_enable should be set to 3. + +The 2103-2 and 2103-4 variants have a third temperature sensor, which can +be connected to two anti-parallel diodes. These values can be read +as temp3 and temp4. If only one diode is attached to this channel, temp4 +will show as "fault". The module parameter "apd=0" can be used to suppress +this 4th channel when anti-parallel diodes are not fitted. diff --git a/Documentation/hwmon/ltc4245 b/Documentation/hwmon/ltc4245 index 86b5880d850..b478b086496 100644 --- a/Documentation/hwmon/ltc4245 +++ b/Documentation/hwmon/ltc4245 @@ -72,9 +72,31 @@ in6_min_alarm 5v output undervoltage alarm in7_min_alarm 3v output undervoltage alarm in8_min_alarm Vee (-12v) output undervoltage alarm -in9_input GPIO voltage data +in9_input GPIO voltage data (see note 1) +in10_input GPIO voltage data (see note 1) +in11_input GPIO voltage data (see note 1) power1_input 12v power usage (mW) power2_input 5v power usage (mW) power3_input 3v power usage (mW) power4_input Vee (-12v) power usage (mW) + + +Note 1 +------ + +If you have NOT configured the driver to sample all GPIO pins as analog +voltages, then the in10_input and in11_input sysfs attributes will not be +created. The driver will sample the GPIO pin that is currently connected to the +ADC as an analog voltage, and report the value in in9_input. + +If you have configured the driver to sample all GPIO pins as analog voltages, +then they will be sampled in round-robin fashion. If userspace reads too +slowly, -EAGAIN will be returned when you read the sysfs attribute containing +the sensor reading. + +The LTC4245 chip can be configured to sample all GPIO pins with two methods: +1) platform data -- see include/linux/i2c/ltc4245.h +2) OF device tree -- add the "ltc4245,use-extra-gpios" property to each chip + +The default mode of operation is to sample a single GPIO pin. diff --git a/Documentation/hwmon/pc87427 b/Documentation/hwmon/pc87427 index db5cc1227a8..8fdd08c9e48 100644 --- a/Documentation/hwmon/pc87427 +++ b/Documentation/hwmon/pc87427 @@ -18,10 +18,11 @@ Description The National Semiconductor Super I/O chip includes complete hardware monitoring capabilities. It can monitor up to 18 voltages, 8 fans and -6 temperature sensors. Only the fans are supported at the moment. +6 temperature sensors. Only the fans and temperatures are supported at +the moment, voltages aren't. -This chip also has fan controlling features, which are not yet supported -by this driver either. +This chip also has fan controlling features (up to 4 PWM outputs), +which are partly supported by this driver. The driver assumes that no more than one chip is present, which seems reasonable. @@ -36,3 +37,23 @@ signal. Speeds down to 83 RPM can be measured. An alarm is triggered if the rotation speed drops below a programmable limit. Another alarm is triggered if the speed is too low to be measured (including stalled or missing fan). + + +Fan Speed Control +----------------- + +Fan speed can be controlled by PWM outputs. There are 4 possible modes: +always off, always on, manual and automatic. The latter isn't supported +by the driver: you can only return to that mode if it was the original +setting, and the configuration interface is missing. + + +Temperature Monitoring +---------------------- + +The PC87427 relies on external sensors (following the SensorPath +standard), so the resolution and range depend on the type of sensor +connected. The integer part can be 8-bit or 9-bit, and can be signed or +not. I couldn't find a way to figure out the external sensor data +temperature format, so user-space adjustment (typically by a factor 2) +may be required. diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index d4e2917c6f1..ff45d1f837c 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -107,10 +107,24 @@ in[0-*]_min Voltage min value. Unit: millivolt RW +in[0-*]_lcrit Voltage critical min value. + Unit: millivolt + RW + If voltage drops to or below this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + in[0-*]_max Voltage max value. Unit: millivolt RW +in[0-*]_crit Voltage critical max value. + Unit: millivolt + RW + If voltage reaches or exceeds this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + in[0-*]_input Voltage input value. Unit: millivolt RO @@ -284,7 +298,7 @@ temp[1-*]_input Temperature input value. Unit: millidegree Celsius RO -temp[1-*]_crit Temperature critical value, typically greater than +temp[1-*]_crit Temperature critical max value, typically greater than corresponding temp_max values. Unit: millidegree Celsius RW @@ -296,6 +310,11 @@ temp[1-*]_crit_hyst from the critical value. RW +temp[1-*]_lcrit Temperature critical min value, typically lower than + corresponding temp_min values. + Unit: millidegree Celsius + RW + temp[1-*]_offset Temperature offset which is added to the temperature reading by the chip. @@ -344,9 +363,6 @@ Also see the Alarms section for status flags associated with temperatures. * Currents * ************ -Note that no known chip provides current measurements as of writing, -so this part is theoretical, so to say. - curr[1-*]_max Current max value Unit: milliampere RW @@ -471,6 +487,7 @@ limit-related alarms, not both. The driver should just reflect the hardware implementation. in[0-*]_alarm +curr[1-*]_alarm fan[1-*]_alarm temp[1-*]_alarm Channel alarm @@ -482,6 +499,8 @@ OR in[0-*]_min_alarm in[0-*]_max_alarm +curr[1-*]_min_alarm +curr[1-*]_max_alarm fan[1-*]_min_alarm fan[1-*]_max_alarm temp[1-*]_min_alarm @@ -497,7 +516,6 @@ to notify open diodes, unconnected fans etc. where the hardware supports it. When this boolean has value 1, the measurement for that channel should not be trusted. -in[0-*]_fault fan[1-*]_fault temp[1-*]_fault Input fault condition @@ -513,6 +531,7 @@ beep_enable Master beep enable RW in[0-*]_beep +curr[1-*]_beep fan[1-*]_beep temp[1-*]_beep Channel beep diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf index b7e42ec4b26..13d556112fc 100644 --- a/Documentation/hwmon/w83627ehf +++ b/Documentation/hwmon/w83627ehf @@ -20,6 +20,10 @@ Supported chips: Prefix: 'w83667hg' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: not available + * Winbond W83667HG-B + Prefix: 'w83667hg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request Authors: Jean Delvare <khali@linux-fr.org> @@ -32,8 +36,8 @@ Description ----------- This driver implements support for the Winbond W83627EHF, W83627EHG, -W83627DHG, W83627DHG-P and W83667HG super I/O chips. We will refer to them -collectively as Winbond chips. +W83627DHG, W83627DHG-P, W83667HG and W83667HG-B super I/O chips. +We will refer to them collectively as Winbond chips. The chips implement three temperature sensors, five fan rotation speed sensors, ten analog voltage sensors (only nine for the 627DHG), one @@ -68,14 +72,15 @@ follows: temp1 -> pwm1 temp2 -> pwm2 temp3 -> pwm3 -prog -> pwm4 (not on 667HG; the programmable setting is not supported by - the driver) +prog -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not + supported by the driver) /sys files ---------- name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG, - it is set to "w83627ehf" and for the W83627DHG it is set to "w83627dhg" + it is set to "w83627ehf", for the W83627DHG it is set to "w83627dhg", + and for the W83667HG it is set to "w83667hg". pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range: 0 (stop) to 255 (full) |