diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 73 |
1 files changed, 66 insertions, 7 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index e07c432c731..09ad7450647 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -147,10 +147,14 @@ and is between 256 and 4096 characters. It is defined in the file default: 0 acpi_sleep= [HW,ACPI] Sleep options - Format: { s3_bios, s3_mode, s3_beep } + Format: { s3_bios, s3_mode, s3_beep, old_ordering } See Documentation/power/video.txt for s3_bios and s3_mode. s3_beep is for debugging; it makes the PC's speaker beep as soon as the kernel's real-mode entry point is called. + old_ordering causes the ACPI 1.0 ordering of the _PTS + control method, wrt putting devices into low power + states, to be enforced (the ACPI 2.0 ordering of _PTS is + used by default). acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode Format: { level | edge | high | low } @@ -271,6 +275,17 @@ and is between 256 and 4096 characters. It is defined in the file aic79xx= [HW,SCSI] See Documentation/scsi/aic79xx.txt. + amd_iommu= [HW,X86-84] + Pass parameters to the AMD IOMMU driver in the system. + Possible values are: + isolate - enable device isolation (each device, as far + as possible, will get its own protection + domain) + amd_iommu_size= [HW,X86-64] + Define the size of the aperture for the AMD IOMMU + driver. Possible values are: + '32M', '64M' (default), '128M', '256M', '512M', '1G' + amijoy.map= [HW,JOY] Amiga joystick support Map of devices attached to JOY0DAT and JOY1DAT Format: <a>,<b> @@ -295,7 +310,7 @@ and is between 256 and 4096 characters. It is defined in the file when initialising the APIC and IO-APIC components. apm= [APM] Advanced Power Management - See header of arch/i386/kernel/apm.c. + See header of arch/x86/kernel/apm_32.c. arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards Format: <io>,<irq>,<nodeID> @@ -560,6 +575,8 @@ and is between 256 and 4096 characters. It is defined in the file debug_objects [KNL] Enable object debugging + debugpat [X86] Enable PAT debugging + decnet.addr= [HW,NET] Format: <area>[,<node>] See also Documentation/networking/decnet.txt. @@ -599,6 +616,29 @@ and is between 256 and 4096 characters. It is defined in the file See drivers/char/README.epca and Documentation/digiepca.txt. + disable_mtrr_cleanup [X86] + enable_mtrr_cleanup [X86] + The kernel tries to adjust MTRR layout from continuous + to discrete, to make X server driver able to add WB + entry later. This parameter enables/disables that. + + mtrr_chunk_size=nn[KMG] [X86] + used for mtrr cleanup. It is largest continous chunk + that could hold holes aka. UC entries. + + mtrr_gran_size=nn[KMG] [X86] + Used for mtrr cleanup. It is granularity of mtrr block. + Default is 1. + Large value could prevent small alignment from + using up MTRRs. + + mtrr_spare_reg_nr=n [X86] + Format: <integer> + Range: 0,7 : spare reg number + Default : 1 + Used for mtrr cleanup. It is spare mtrr entries number. + Set to 2 or more if your graphical card needs more. + disable_mtrr_trim [X86, Intel and AMD only] By default the kernel will trim any uncacheable memory out of your available memory pool based on @@ -638,7 +678,7 @@ and is between 256 and 4096 characters. It is defined in the file elanfreq= [X86-32] See comment before function elanfreq_setup() in - arch/i386/kernel/cpu/cpufreq/elanfreq.c. + arch/x86/kernel/cpu/cpufreq/elanfreq.c. elevator= [IOSCHED] Format: {"anticipatory" | "cfq" | "deadline" | "noop"} @@ -722,9 +762,6 @@ and is between 256 and 4096 characters. It is defined in the file hd= [EIDE] (E)IDE hard drive subsystem geometry Format: <cyl>,<head>,<sect> - hd?= [HW] (E)IDE subsystem - hd?lun= See Documentation/ide/ide.txt. - highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact size of <nn>. This works even on boxes that have no highmem otherwise. This also works to reduce highmem @@ -785,7 +822,7 @@ and is between 256 and 4096 characters. It is defined in the file See Documentation/ide/ide.txt. idle= [X86] - Format: idle=poll or idle=mwait + Format: idle=poll or idle=mwait, idle=halt, idle=nomwait Poll forces a polling idle loop that can slightly improves the performance of waking up a idle CPU, but will use a lot of power and make the system run hot. Not recommended. @@ -793,6 +830,9 @@ and is between 256 and 4096 characters. It is defined in the file to not use it because it doesn't save as much power as a normal idle loop use the MONITOR/MWAIT idle loop anyways. Performance should be the same as idle=poll. + idle=halt. Halt is forced to be used for CPU idle. + In such case C2/C3 won't be used again. + idle=nomwait. Disable mwait for CPU C-states ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem Claim all unknown PCI IDE storage controllers. @@ -1208,6 +1248,11 @@ and is between 256 and 4096 characters. It is defined in the file mtdparts= [MTD] See drivers/mtd/cmdlinepart.c. + mtdset= [ARM] + ARM/S3C2412 JIVE boot control + + See arch/arm/mach-s3c2412/mach-jive.c + mtouchusb.raw_coordinates= [HW] Make the MicroTouch USB driver use raw coordinates ('y', default) or cooked coordinates ('n') @@ -1496,6 +1541,9 @@ and is between 256 and 4096 characters. It is defined in the file Use with caution as certain devices share address decoders between ROMs and other resources. + norom [X86-32,X86_64] Do not assign address space to + expansion ROMs that do not already have + BIOS assigned address ranges. irqmask=0xMMMM [X86-32] Set a bit mask of IRQs allowed to be assigned automatically to PCI devices. You can make the kernel exclude IRQs of your ISA cards @@ -1571,6 +1619,10 @@ and is between 256 and 4096 characters. It is defined in the file Format: { parport<nr> | timid | 0 } See also Documentation/parport.txt. + pmtmr= [X86] Manual setup of pmtmr I/O Port. + Override pmtimer IOPort with a hex value. + e.g. pmtmr=0x508 + pnpacpi= [ACPI] { off } @@ -1679,6 +1731,10 @@ and is between 256 and 4096 characters. It is defined in the file Format: <reboot_mode>[,<reboot_mode2>[,...]] See arch/*/kernel/reboot.c or arch/*/kernel/process.c + relax_domain_level= + [KNL, SMP] Set scheduler's default relax_domain_level. + See Documentation/cpusets.txt. + reserve= [KNL,BUGS] Force the kernel to ignore some iomem area reservetop= [X86-32] @@ -2112,6 +2168,9 @@ and is between 256 and 4096 characters. It is defined in the file usbhid.mousepoll= [USBHID] The interval which mice are to be polled at. + add_efi_memmap [EFI; x86-32,X86-64] Include EFI memory map in + kernel's map of available physical RAM. + vdso= [X86-32,SH,x86-64] vdso=2: enable compat VDSO (default with COMPAT_VDSO) vdso=1: enable VDSO (default) |