diff options
Diffstat (limited to 'Documentation/laptops/thinkpad-acpi.txt')
| -rw-r--r-- | Documentation/laptops/thinkpad-acpi.txt | 174 |
1 files changed, 37 insertions, 137 deletions
diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index 78e354b42f6..e2ddcdeb61b 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -36,8 +36,6 @@ detailed description): - Bluetooth enable and disable - video output switching, expansion control - ThinkLight on and off - - limited docking and undocking - - UltraBay eject - CMOS/UCMS control - LED control - ACPI sounds @@ -729,131 +727,6 @@ cannot be read or if it is unknown, thinkpad-acpi will report it as "off". It is impossible to know if the status returned through sysfs is valid. -Docking / undocking -- /proc/acpi/ibm/dock ------------------------------------------- - -Docking and undocking (e.g. with the X4 UltraBase) requires some -actions to be taken by the operating system to safely make or break -the electrical connections with the dock. - -The docking feature of this driver generates the following ACPI events: - - ibm/dock GDCK 00000003 00000001 -- eject request - ibm/dock GDCK 00000003 00000002 -- undocked - ibm/dock GDCK 00000000 00000003 -- docked - -NOTE: These events will only be generated if the laptop was docked -when originally booted. This is due to the current lack of support for -hot plugging of devices in the Linux ACPI framework. If the laptop was -booted while not in the dock, the following message is shown in the -logs: - - Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present - -In this case, no dock-related events are generated but the dock and -undock commands described below still work. They can be executed -manually or triggered by Fn key combinations (see the example acpid -configuration files included in the driver tarball package available -on the web site). - -When the eject request button on the dock is pressed, the first event -above is generated. The handler for this event should issue the -following command: - - echo undock > /proc/acpi/ibm/dock - -After the LED on the dock goes off, it is safe to eject the laptop. -Note: if you pressed this key by mistake, go ahead and eject the -laptop, then dock it back in. Otherwise, the dock may not function as -expected. - -When the laptop is docked, the third event above is generated. The -handler for this event should issue the following command to fully -enable the dock: - - echo dock > /proc/acpi/ibm/dock - -The contents of the /proc/acpi/ibm/dock file shows the current status -of the dock, as provided by the ACPI framework. - -The docking support in this driver does not take care of enabling or -disabling any other devices you may have attached to the dock. For -example, a CD drive plugged into the UltraBase needs to be disabled or -enabled separately. See the provided example acpid configuration files -for how this can be accomplished. - -There is no support yet for PCI devices that may be attached to a -docking station, e.g. in the ThinkPad Dock II. The driver currently -does not recognize, enable or disable such devices. This means that -the only docking stations currently supported are the X-series -UltraBase docks and "dumb" port replicators like the Mini Dock (the -latter don't need any ACPI support, actually). - - -UltraBay eject -- /proc/acpi/ibm/bay ------------------------------------- - -Inserting or ejecting an UltraBay device requires some actions to be -taken by the operating system to safely make or break the electrical -connections with the device. - -This feature generates the following ACPI events: - - ibm/bay MSTR 00000003 00000000 -- eject request - ibm/bay MSTR 00000001 00000000 -- eject lever inserted - -NOTE: These events will only be generated if the UltraBay was present -when the laptop was originally booted (on the X series, the UltraBay -is in the dock, so it may not be present if the laptop was undocked). -This is due to the current lack of support for hot plugging of devices -in the Linux ACPI framework. If the laptop was booted without the -UltraBay, the following message is shown in the logs: - - Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present - -In this case, no bay-related events are generated but the eject -command described below still works. It can be executed manually or -triggered by a hot key combination. - -Sliding the eject lever generates the first event shown above. The -handler for this event should take whatever actions are necessary to -shut down the device in the UltraBay (e.g. call idectl), then issue -the following command: - - echo eject > /proc/acpi/ibm/bay - -After the LED on the UltraBay goes off, it is safe to pull out the -device. - -When the eject lever is inserted, the second event above is -generated. The handler for this event should take whatever actions are -necessary to enable the UltraBay device (e.g. call idectl). - -The contents of the /proc/acpi/ibm/bay file shows the current status -of the UltraBay, as provided by the ACPI framework. - -EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use -this feature, you need to supply the experimental=1 parameter when -loading the module): - -These models do not have a button near the UltraBay device to request -a hot eject but rather require the laptop to be put to sleep -(suspend-to-ram) before the bay device is ejected or inserted). -The sequence of steps to eject the device is as follows: - - echo eject > /proc/acpi/ibm/bay - put the ThinkPad to sleep - remove the drive - resume from sleep - cat /proc/acpi/ibm/bay should show that the drive was removed - -On the A3x, both the UltraBay 2000 and UltraBay Plus devices are -supported. Use "eject2" instead of "eject" for the second bay. - -Note: the UltraBay eject support on the 600e/x, A22p and A3x is -EXPERIMENTAL and may not work as expected. USE WITH CAUTION! - - CMOS/UCMS control ----------------- @@ -920,7 +793,7 @@ The available commands are: echo '<LED number> off' >/proc/acpi/ibm/led echo '<LED number> blink' >/proc/acpi/ibm/led -The <LED number> range is 0 to 7. The set of LEDs that can be +The <LED number> range is 0 to 15. The set of LEDs that can be controlled varies from model to model. Here is the common ThinkPad mapping: @@ -932,6 +805,11 @@ mapping: 5 - UltraBase battery slot 6 - (unknown) 7 - standby + 8 - dock status 1 + 9 - dock status 2 + 10, 11 - (unknown) + 12 - thinkvantage + 13, 14, 15 - (unknown) All of the above can be turned on and off and can be made to blink. @@ -940,10 +818,12 @@ sysfs notes: The ThinkPad LED sysfs interface is described in detail by the LED class documentation, in Documentation/leds-class.txt. -The leds are named (in LED ID order, from 0 to 7): +The LEDs are named (in LED ID order, from 0 to 12): "tpacpi::power", "tpacpi:orange:batt", "tpacpi:green:batt", "tpacpi::dock_active", "tpacpi::bay_active", "tpacpi::dock_batt", -"tpacpi::unknown_led", "tpacpi::standby". +"tpacpi::unknown_led", "tpacpi::standby", "tpacpi::dock_status1", +"tpacpi::dock_status2", "tpacpi::unknown_led2", "tpacpi::unknown_led3", +"tpacpi::thinkvantage". Due to limitations in the sysfs LED class, if the status of the LED indicators cannot be read due to an error, thinkpad-acpi will report it as @@ -958,6 +838,12 @@ ThinkPad indicator LED should blink in hardware accelerated mode, use the "timer" trigger, and leave the delay_on and delay_off parameters set to zero (to request hardware acceleration autodetection). +LEDs that are known not to exist in a given ThinkPad model are not +made available through the sysfs interface. If you have a dock and you +notice there are LEDs listed for your ThinkPad that do not exist (and +are not in the dock), or if you notice that there are missing LEDs, +a report to ibm-acpi-devel@lists.sourceforge.net is appreciated. + ACPI sounds -- /proc/acpi/ibm/beep ---------------------------------- @@ -1156,17 +1042,19 @@ may not be distinct. Later Lenovo models that implement the ACPI display backlight brightness control methods have 16 levels, ranging from 0 to 15. -There are two interfaces to the firmware for direct brightness control, -EC and UCMS (or CMOS). To select which one should be used, use the -brightness_mode module parameter: brightness_mode=1 selects EC mode, -brightness_mode=2 selects UCMS mode, brightness_mode=3 selects EC -mode with NVRAM backing (so that brightness changes are remembered -across shutdown/reboot). +For IBM ThinkPads, there are two interfaces to the firmware for direct +brightness control, EC and UCMS (or CMOS). To select which one should be +used, use the brightness_mode module parameter: brightness_mode=1 selects +EC mode, brightness_mode=2 selects UCMS mode, brightness_mode=3 selects EC +mode with NVRAM backing (so that brightness changes are remembered across +shutdown/reboot). The driver tries to select which interface to use from a table of defaults for each ThinkPad model. If it makes a wrong choice, please report this as a bug, so that we can fix it. +Lenovo ThinkPads only support brightness_mode=2 (UCMS). + When display backlight brightness controls are available through the standard ACPI interface, it is best to use it instead of this direct ThinkPad-specific interface. The driver will disable its native @@ -1254,7 +1142,7 @@ Fan control and monitoring: fan speed, fan enable/disable procfs: /proc/acpi/ibm/fan sysfs device attributes: (hwmon "thinkpad") fan1_input, pwm1, - pwm1_enable + pwm1_enable, fan2_input sysfs hwmon driver attributes: fan_watchdog NOTE NOTE NOTE: fan control operations are disabled by default for @@ -1267,6 +1155,9 @@ from the hardware registers of the embedded controller. This is known to work on later R, T, X and Z series ThinkPads but may show a bogus value on other models. +Some Lenovo ThinkPads support a secondary fan. This fan cannot be +controlled separately, it shares the main fan control. + Fan levels: Most ThinkPad fans work in "levels" at the firmware interface. Level 0 @@ -1397,6 +1288,11 @@ hwmon device attribute fan1_input: which can take up to two minutes. May return rubbish on older ThinkPads. +hwmon device attribute fan2_input: + Fan tachometer reading, in RPM, for the secondary fan. + Available only on some ThinkPads. If the secondary fan is + not installed, will always read 0. + hwmon driver attribute fan_watchdog: Fan safety watchdog timer interval, in seconds. Minimum is 1 second, maximum is 120 seconds. 0 disables the watchdog. @@ -1555,3 +1451,7 @@ Sysfs interface changelog: 0x020300: hotkey enable/disable support removed, attributes hotkey_bios_enabled and hotkey_enable deprecated and marked for removal. + +0x020400: Marker for 16 LEDs support. Also, LEDs that are known + to not exist in a given model are not registered with + the LED sysfs class anymore. |