diff options
Diffstat (limited to 'Documentation/networking/ip-sysctl.txt')
| -rw-r--r-- | Documentation/networking/ip-sysctl.txt | 878 |
1 files changed, 878 insertions, 0 deletions
diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt new file mode 100644 index 00000000000..a2c893a7475 --- /dev/null +++ b/Documentation/networking/ip-sysctl.txt @@ -0,0 +1,878 @@ +/proc/sys/net/ipv4/* Variables: + +ip_forward - BOOLEAN + 0 - disabled (default) + not 0 - enabled + + Forward Packets between interfaces. + + This variable is special, its change resets all configuration + parameters to their default state (RFC1122 for hosts, RFC1812 + for routers) + +ip_default_ttl - INTEGER + default 64 + +ip_no_pmtu_disc - BOOLEAN + Disable Path MTU Discovery. + default FALSE + +min_pmtu - INTEGER + default 562 - minimum discovered Path MTU + +mtu_expires - INTEGER + Time, in seconds, that cached PMTU information is kept. + +min_adv_mss - INTEGER + The advertised MSS depends on the first hop route MTU, but will + never be lower than this setting. + +IP Fragmentation: + +ipfrag_high_thresh - INTEGER + Maximum memory used to reassemble IP fragments. When + ipfrag_high_thresh bytes of memory is allocated for this purpose, + the fragment handler will toss packets until ipfrag_low_thresh + is reached. + +ipfrag_low_thresh - INTEGER + See ipfrag_high_thresh + +ipfrag_time - INTEGER + Time in seconds to keep an IP fragment in memory. + +ipfrag_secret_interval - INTEGER + Regeneration interval (in seconds) of the hash secret (or lifetime + for the hash secret) for IP fragments. + Default: 600 + +INET peer storage: + +inet_peer_threshold - INTEGER + The approximate size of the storage. Starting from this threshold + entries will be thrown aggressively. This threshold also determines + entries' time-to-live and time intervals between garbage collection + passes. More entries, less time-to-live, less GC interval. + +inet_peer_minttl - INTEGER + Minimum time-to-live of entries. Should be enough to cover fragment + time-to-live on the reassembling side. This minimum time-to-live is + guaranteed if the pool size is less than inet_peer_threshold. + Measured in jiffies(1). + +inet_peer_maxttl - INTEGER + Maximum time-to-live of entries. Unused entries will expire after + this period of time if there is no memory pressure on the pool (i.e. + when the number of entries in the pool is very small). + Measured in jiffies(1). + +inet_peer_gc_mintime - INTEGER + Minimum interval between garbage collection passes. This interval is + in effect under high memory pressure on the pool. + Measured in jiffies(1). + +inet_peer_gc_maxtime - INTEGER + Minimum interval between garbage collection passes. This interval is + in effect under low (or absent) memory pressure on the pool. + Measured in jiffies(1). + +TCP variables: + +tcp_syn_retries - INTEGER + Number of times initial SYNs for an active TCP connection attempt + will be retransmitted. Should not be higher than 255. Default value + is 5, which corresponds to ~180seconds. + +tcp_synack_retries - INTEGER + Number of times SYNACKs for a passive TCP connection attempt will + be retransmitted. Should not be higher than 255. Default value + is 5, which corresponds to ~180seconds. + +tcp_keepalive_time - INTEGER + How often TCP sends out keepalive messages when keepalive is enabled. + Default: 2hours. + +tcp_keepalive_probes - INTEGER + How many keepalive probes TCP sends out, until it decides that the + connection is broken. Default value: 9. + +tcp_keepalive_intvl - INTEGER + How frequently the probes are send out. Multiplied by + tcp_keepalive_probes it is time to kill not responding connection, + after probes started. Default value: 75sec i.e. connection + will be aborted after ~11 minutes of retries. + +tcp_retries1 - INTEGER + How many times to retry before deciding that something is wrong + and it is necessary to report this suspicion to network layer. + Minimal RFC value is 3, it is default, which corresponds + to ~3sec-8min depending on RTO. + +tcp_retries2 - INTEGER + How may times to retry before killing alive TCP connection. + RFC1122 says that the limit should be longer than 100 sec. + It is too small number. Default value 15 corresponds to ~13-30min + depending on RTO. + +tcp_orphan_retries - INTEGER + How may times to retry before killing TCP connection, closed + by our side. Default value 7 corresponds to ~50sec-16min + depending on RTO. If you machine is loaded WEB server, + you should think about lowering this value, such sockets + may consume significant resources. Cf. tcp_max_orphans. + +tcp_fin_timeout - INTEGER + Time to hold socket in state FIN-WAIT-2, if it was closed + by our side. Peer can be broken and never close its side, + or even died unexpectedly. Default value is 60sec. + Usual value used in 2.2 was 180 seconds, you may restore + it, but remember that if your machine is even underloaded WEB server, + you risk to overflow memory with kilotons of dead sockets, + FIN-WAIT-2 sockets are less dangerous than FIN-WAIT-1, + because they eat maximum 1.5K of memory, but they tend + to live longer. Cf. tcp_max_orphans. + +tcp_max_tw_buckets - INTEGER + Maximal number of timewait sockets held by system simultaneously. + If this number is exceeded time-wait socket is immediately destroyed + and warning is printed. This limit exists only to prevent + simple DoS attacks, you _must_ not lower the limit artificially, + but rather increase it (probably, after increasing installed memory), + if network conditions require more than default value. + +tcp_tw_recycle - BOOLEAN + Enable fast recycling TIME-WAIT sockets. Default value is 0. + It should not be changed without advice/request of technical + experts. + +tcp_tw_reuse - BOOLEAN + Allow to reuse TIME-WAIT sockets for new connections when it is + safe from protocol viewpoint. Default value is 0. + It should not be changed without advice/request of technical + experts. + +tcp_max_orphans - INTEGER + Maximal number of TCP sockets not attached to any user file handle, + held by system. If this number is exceeded orphaned connections are + reset immediately and warning is printed. This limit exists + only to prevent simple DoS attacks, you _must_ not rely on this + or lower the limit artificially, but rather increase it + (probably, after increasing installed memory), + if network conditions require more than default value, + and tune network services to linger and kill such states + more aggressively. Let me to remind again: each orphan eats + up to ~64K of unswappable memory. + +tcp_abort_on_overflow - BOOLEAN + If listening service is too slow to accept new connections, + reset them. Default state is FALSE. It means that if overflow + occurred due to a burst, connection will recover. Enable this + option _only_ if you are really sure that listening daemon + cannot be tuned to accept connections faster. Enabling this + option can harm clients of your server. + +tcp_syncookies - BOOLEAN + Only valid when the kernel was compiled with CONFIG_SYNCOOKIES + Send out syncookies when the syn backlog queue of a socket + overflows. This is to prevent against the common 'syn flood attack' + Default: FALSE + + Note, that syncookies is fallback facility. + It MUST NOT be used to help highly loaded servers to stand + against legal connection rate. If you see synflood warnings + in your logs, but investigation shows that they occur + because of overload with legal connections, you should tune + another parameters until this warning disappear. + See: tcp_max_syn_backlog, tcp_synack_retries, tcp_abort_on_overflow. + + syncookies seriously violate TCP protocol, do not allow + to use TCP extensions, can result in serious degradation + of some services (f.e. SMTP relaying), visible not by you, + but your clients and relays, contacting you. While you see + synflood warnings in logs not being really flooded, your server + is seriously misconfigured. + +tcp_stdurg - BOOLEAN + Use the Host requirements interpretation of the TCP urg pointer field. + Most hosts use the older BSD interpretation, so if you turn this on + Linux might not communicate correctly with them. + Default: FALSE + +tcp_max_syn_backlog - INTEGER + Maximal number of remembered connection requests, which are + still did not receive an acknowledgment from connecting client. + Default value is 1024 for systems with more than 128Mb of memory, + and 128 for low memory machines. If server suffers of overload, + try to increase this number. + +tcp_window_scaling - BOOLEAN + Enable window scaling as defined in RFC1323. + +tcp_timestamps - BOOLEAN + Enable timestamps as defined in RFC1323. + +tcp_sack - BOOLEAN + Enable select acknowledgments (SACKS). + +tcp_fack - BOOLEAN + Enable FACK congestion avoidance and fast retransmission. + The value is not used, if tcp_sack is not enabled. + +tcp_dsack - BOOLEAN + Allows TCP to send "duplicate" SACKs. + +tcp_ecn - BOOLEAN + Enable Explicit Congestion Notification in TCP. + +tcp_reordering - INTEGER + Maximal reordering of packets in a TCP stream. + Default: 3 + +tcp_retrans_collapse - BOOLEAN + Bug-to-bug compatibility with some broken printers. + On retransmit try to send bigger packets to work around bugs in + certain TCP stacks. + +tcp_wmem - vector of 3 INTEGERs: min, default, max + min: Amount of memory reserved for send buffers for TCP socket. + Each TCP socket has rights to use it due to fact of its birth. + Default: 4K + + default: Amount of memory allowed for send buffers for TCP socket + by default. This value overrides net.core.wmem_default used + by other protocols, it is usually lower than net.core.wmem_default. + Default: 16K + + max: Maximal amount of memory allowed for automatically selected + send buffers for TCP socket. This value does not override + net.core.wmem_max, "static" selection via SO_SNDBUF does not use this. + Default: 128K + +tcp_rmem - vector of 3 INTEGERs: min, default, max + min: Minimal size of receive buffer used by TCP sockets. + It is guaranteed to each TCP socket, even under moderate memory + pressure. + Default: 8K + + default: default size of receive buffer used by TCP sockets. + This value overrides net.core.rmem_default used by other protocols. + Default: 87380 bytes. This value results in window of 65535 with + default setting of tcp_adv_win_scale and tcp_app_win:0 and a bit + less for default tcp_app_win. See below about these variables. + + max: maximal size of receive buffer allowed for automatically + selected receiver buffers for TCP socket. This value does not override + net.core.rmem_max, "static" selection via SO_RCVBUF does not use this. + Default: 87380*2 bytes. + +tcp_mem - vector of 3 INTEGERs: min, pressure, max + low: below this number of pages TCP is not bothered about its + memory appetite. + + pressure: when amount of memory allocated by TCP exceeds this number + of pages, TCP moderates its memory consumption and enters memory + pressure mode, which is exited when memory consumption falls + under "low". + + high: number of pages allowed for queueing by all TCP sockets. + + Defaults are calculated at boot time from amount of available + memory. + +tcp_app_win - INTEGER + Reserve max(window/2^tcp_app_win, mss) of window for application + buffer. Value 0 is special, it means that nothing is reserved. + Default: 31 + +tcp_adv_win_scale - INTEGER + Count buffering overhead as bytes/2^tcp_adv_win_scale + (if tcp_adv_win_scale > 0) or bytes-bytes/2^(-tcp_adv_win_scale), + if it is <= 0. + Default: 2 + +tcp_rfc1337 - BOOLEAN + If set, the TCP stack behaves conforming to RFC1337. If unset, + we are not conforming to RFC, but prevent TCP TIME_WAIT + assassination. + Default: 0 + +tcp_low_latency - BOOLEAN + If set, the TCP stack makes decisions that prefer lower + latency as opposed to higher throughput. By default, this + option is not set meaning that higher throughput is preferred. + An example of an application where this default should be + changed would be a Beowulf compute cluster. + Default: 0 + +tcp_westwood - BOOLEAN + Enable TCP Westwood+ congestion control algorithm. + TCP Westwood+ is a sender-side only modification of the TCP Reno + protocol stack that optimizes the performance of TCP congestion + control. It is based on end-to-end bandwidth estimation to set + congestion window and slow start threshold after a congestion + episode. Using this estimation, TCP Westwood+ adaptively sets a + slow start threshold and a congestion window which takes into + account the bandwidth used at the time congestion is experienced. + TCP Westwood+ significantly increases fairness wrt TCP Reno in + wired networks and throughput over wireless links. + Default: 0 + +tcp_vegas_cong_avoid - BOOLEAN + Enable TCP Vegas congestion avoidance algorithm. + TCP Vegas is a sender-side only change to TCP that anticipates + the onset of congestion by estimating the bandwidth. TCP Vegas + adjusts the sending rate by modifying the congestion + window. TCP Vegas should provide less packet loss, but it is + not as aggressive as TCP Reno. + Default:0 + +tcp_bic - BOOLEAN + Enable BIC TCP congestion control algorithm. + BIC-TCP is a sender-side only change that ensures a linear RTT + fairness under large windows while offering both scalability and + bounded TCP-friendliness. The protocol combines two schemes + called additive increase and binary search increase. When the + congestion window is large, additive increase with a large + increment ensures linear RTT fairness as well as good + scalability. Under small congestion windows, binary search + increase provides TCP friendliness. + Default: 0 + +tcp_bic_low_window - INTEGER + Sets the threshold window (in packets) where BIC TCP starts to + adjust the congestion window. Below this threshold BIC TCP behaves + the same as the default TCP Reno. + Default: 14 + +tcp_bic_fast_convergence - BOOLEAN + Forces BIC TCP to more quickly respond to changes in congestion + window. Allows two flows sharing the same connection to converge + more rapidly. + Default: 1 + +tcp_default_win_scale - INTEGER + Sets the minimum window scale TCP will negotiate for on all + conections. + Default: 7 + +tcp_tso_win_divisor - INTEGER + This allows control over what percentage of the congestion window + can be consumed by a single TSO frame. + The setting of this parameter is a choice between burstiness and + building larger TSO frames. + Default: 8 + +tcp_frto - BOOLEAN + Enables F-RTO, an enhanced recovery algorithm for TCP retransmission + timeouts. It is particularly beneficial in wireless environments + where packet loss is typically due to random radio interference + rather than intermediate router congestion. + +somaxconn - INTEGER + Limit of socket listen() backlog, known in userspace as SOMAXCONN. + Defaults to 128. See also tcp_max_syn_backlog for additional tuning + for TCP sockets. + +IP Variables: + +ip_local_port_range - 2 INTEGERS + Defines the local port range that is used by TCP and UDP to + choose the local port. The first number is the first, the + second the last local port number. Default value depends on + amount of memory available on the system: + > 128Mb 32768-61000 + < 128Mb 1024-4999 or even less. + This number defines number of active connections, which this + system can issue simultaneously to systems not supporting + TCP extensions (timestamps). With tcp_tw_recycle enabled + (i.e. by default) range 1024-4999 is enough to issue up to + 2000 connections per second to systems supporting timestamps. + +ip_nonlocal_bind - BOOLEAN + If set, allows processes to bind() to non-local IP addresses, + which can be quite useful - but may break some applications. + Default: 0 + +ip_dynaddr - BOOLEAN + If set non-zero, enables support for dynamic addresses. + If set to a non-zero value larger than 1, a kernel log + message will be printed when dynamic address rewriting + occurs. + Default: 0 + +icmp_echo_ignore_all - BOOLEAN +icmp_echo_ignore_broadcasts - BOOLEAN + If either is set to true, then the kernel will ignore either all + ICMP ECHO requests sent to it or just those to broadcast/multicast + addresses, respectively. + +icmp_ratelimit - INTEGER + Limit the maximal rates for sending ICMP packets whose type matches + icmp_ratemask (see below) to specific targets. + 0 to disable any limiting, otherwise the maximal rate in jiffies(1) + Default: 100 + +icmp_ratemask - INTEGER + Mask made of ICMP types for which rates are being limited. + Significant bits: IHGFEDCBA9876543210 + Default mask: 0000001100000011000 (6168) + + Bit definitions (see include/linux/icmp.h): + 0 Echo Reply + 3 Destination Unreachable * + 4 Source Quench * + 5 Redirect + 8 Echo Request + B Time Exceeded * + C Parameter Problem * + D Timestamp Request + E Timestamp Reply + F Info Request + G Info Reply + H Address Mask Request + I Address Mask Reply + + * These are rate limited by default (see default mask above) + +icmp_ignore_bogus_error_responses - BOOLEAN + Some routers violate RFC1122 by sending bogus responses to broadcast + frames. Such violations are normally logged via a kernel warning. + If this is set to TRUE, the kernel will not give such warnings, which + will avoid log file clutter. + Default: FALSE + +igmp_max_memberships - INTEGER + Change the maximum number of multicast groups we can subscribe to. + Default: 20 + +conf/interface/* changes special settings per interface (where "interface" is + the name of your network interface) +conf/all/* is special, changes the settings for all interfaces + + +log_martians - BOOLEAN + Log packets with impossible addresses to kernel log. + log_martians for the interface will be enabled if at least one of + conf/{all,interface}/log_martians is set to TRUE, + it will be disabled otherwise + +accept_redirects - BOOLEAN + Accept ICMP redirect messages. + accept_redirects for the interface will be enabled if: + - both conf/{all,interface}/accept_redirects are TRUE in the case forwarding + for the interface is enabled + or + - at least one of conf/{all,interface}/accept_redirects is TRUE in the case + forwarding for the interface is disabled + accept_redirects for the interface will be disabled otherwise + default TRUE (host) + FALSE (router) + +forwarding - BOOLEAN + Enable IP forwarding on this interface. + +mc_forwarding - BOOLEAN + Do multicast routing. The kernel needs to be compiled with CONFIG_MROUTE + and a multicast routing daemon is required. + conf/all/mc_forwarding must also be set to TRUE to enable multicast routing + for the interface + +medium_id - INTEGER + Integer value used to differentiate the devices by the medium they + are attached to. Two devices can have different id values when + the broadcast packets are received only on one of them. + The default value 0 means that the device is the only interface + to its medium, value of -1 means that medium is not known. + + Currently, it is used to change the proxy_arp behavior: + the proxy_arp feature is enabled for packets forwarded between + two devices attached to different media. + +proxy_arp - BOOLEAN + Do proxy arp. + proxy_arp for the interface will be enabled if at least one of + conf/{all,interface}/proxy_arp is set to TRUE, + it will be disabled otherwise + +shared_media - BOOLEAN + Send(router) or accept(host) RFC1620 shared media redirects. + Overrides ip_secure_redirects. + shared_media for the interface will be enabled if at least one of + conf/{all,interface}/shared_media is set to TRUE, + it will be disabled otherwise + default TRUE + +secure_redirects - BOOLEAN + Accept ICMP redirect messages only for gateways, + listed in default gateway list. + secure_redirects for the interface will be enabled if at least one of + conf/{all,interface}/secure_redirects is set to TRUE, + it will be disabled otherwise + default TRUE + +send_redirects - BOOLEAN + Send redirects, if router. + send_redirects for the interface will be enabled if at least one of + conf/{all,interface}/send_redirects is set to TRUE, + it will be disabled otherwise + Default: TRUE + +bootp_relay - BOOLEAN + Accept packets with source address 0.b.c.d destined + not to this host as local ones. It is supposed, that + BOOTP relay daemon will catch and forward such packets. + conf/all/bootp_relay must also be set to TRUE to enable BOOTP relay + for the interface + default FALSE + Not Implemented Yet. + +accept_source_route - BOOLEAN + Accept packets with SRR option. + conf/all/accept_source_route must also be set to TRUE to accept packets + with SRR option on the interface + default TRUE (router) + FALSE (host) + +rp_filter - BOOLEAN + 1 - do source validation by reversed path, as specified in RFC1812 + Recommended option for single homed hosts and stub network + routers. Could cause troubles for complicated (not loop free) + networks running a slow unreliable protocol (sort of RIP), + or using static routes. + + 0 - No source validation. + + conf/all/rp_filter must also be set to TRUE to do source validation + on the interface + + Default value is 0. Note that some distributions enable it + in startup scripts. + +arp_filter - BOOLEAN + 1 - Allows you to have multiple network interfaces on the same + subnet, and have the ARPs for each interface be answered + based on whether or not the kernel would route a packet from + the ARP'd IP out that interface (therefore you must use source + based routing for this to work). In other words it allows control + of which cards (usually 1) will respond to an arp request. + + 0 - (default) The kernel can respond to arp requests with addresses + from other interfaces. This may seem wrong but it usually makes + sense, because it increases the chance of successful communication. + IP addresses are owned by the complete host on Linux, not by + particular interfaces. Only for more complex setups like load- + balancing, does this behaviour cause problems. + + arp_filter for the interface will be enabled if at least one of + conf/{all,interface}/arp_filter is set to TRUE, + it will be disabled otherwise + +arp_announce - INTEGER + Define different restriction levels for announcing the local + source IP address from IP packets in ARP requests sent on + interface: + 0 - (default) Use any local address, configured on any interface + 1 - Try to avoid local addresses that are not in the target's + subnet for this interface. This mode is useful when target + hosts reachable via this interface require the source IP + address in ARP requests to be part of their logical network + configured on the receiving interface. When we generate the + request we will check all our subnets that include the + target IP and will preserve the source address if it is from + such subnet. If there is no such subnet we select source + address according to the rules for level 2. + 2 - Always use the best local address for this target. + In this mode we ignore the source address in the IP packet + and try to select local address that we prefer for talks with + the target host. Such local address is selected by looking + for primary IP addresses on all our subnets on the outgoing + interface that include the target IP address. If no suitable + local address is found we select the first local address + we have on the outgoing interface or on all other interfaces, + with the hope we will receive reply for our request and + even sometimes no matter the source IP address we announce. + + The max value from conf/{all,interface}/arp_announce is used. + + Increasing the restriction level gives more chance for + receiving answer from the resolved target while decreasing + the level announces more valid sender's information. + +arp_ignore - INTEGER + Define different modes for sending replies in response to + received ARP requests that resolve local target IP addresses: + 0 - (default): reply for any local target IP address, configured + on any interface + 1 - reply only if the target IP address is local address + configured on the incoming interface + 2 - reply only if the target IP address is local address + configured on the incoming interface and both with the + sender's IP address are part from same subnet on this interface + 3 - do not reply for local addresses configured with scope host, + only resolutions for global and link addresses are replied + 4-7 - reserved + 8 - do not reply for all local addresses + + The max value from conf/{all,interface}/arp_ignore is used + when ARP request is received on the {interface} + +app_solicit - INTEGER + The maximum number of probes to send to the user space ARP daemon + via netlink before dropping back to multicast probes (see + mcast_solicit). Defaults to 0. + +disable_policy - BOOLEAN + Disable IPSEC policy (SPD) for this interface + +disable_xfrm - BOOLEAN + Disable IPSEC encryption on this interface, whatever the policy + + + +tag - INTEGER + Allows you to write a number, which can be used as required. + Default value is 0. + +(1) Jiffie: internal timeunit for the kernel. On the i386 1/100s, on the +Alpha 1/1024s. See the HZ define in /usr/include/asm/param.h for the exact +value on your system. + +Alexey Kuznetsov. +kuznet@ms2.inr.ac.ru + +Updated by: +Andi Kleen +ak@muc.de +Nicolas Delon +delon.nicolas@wanadoo.fr + + + + +/proc/sys/net/ipv6/* Variables: + +IPv6 has no global variables such as tcp_*. tcp_* settings under ipv4/ also +apply to IPv6 [XXX?]. + +bindv6only - BOOLEAN + Default value for IPV6_V6ONLY socket option, + which restricts use of the IPv6 socket to IPv6 communication + only. + TRUE: disable IPv4-mapped address feature + FALSE: enable IPv4-mapped address feature + + Default: FALSE (as specified in RFC2553bis) + +IPv6 Fragmentation: + +ip6frag_high_thresh - INTEGER + Maximum memory used to reassemble IPv6 fragments. When + ip6frag_high_thresh bytes of memory is allocated for this purpose, + the fragment handler will toss packets until ip6frag_low_thresh + is reached. + +ip6frag_low_thresh - INTEGER + See ip6frag_high_thresh + +ip6frag_time - INTEGER + Time in seconds to keep an IPv6 fragment in memory. + +ip6frag_secret_interval - INTEGER + Regeneration interval (in seconds) of the hash secret (or lifetime + for the hash secret) for IPv6 fragments. + Default: 600 + +conf/default/*: + Change the interface-specific default settings. + + +conf/all/*: + Change all the interface-specific settings. + + [XXX: Other special features than forwarding?] + +conf/all/forwarding - BOOLEAN + Enable global IPv6 forwarding between all interfaces. + + IPv4 and IPv6 work differently here; e.g. netfilter must be used + to control which interfaces may forward packets and which not. + + This also sets all interfaces' Host/Router setting + 'forwarding' to the specified value. See below for details. + + This referred to as global forwarding. + +conf/interface/*: + Change special settings per interface. + + The functional behaviour for certain settings is different + depending on whether local forwarding is enabled or not. + +accept_ra - BOOLEAN + Accept Router Advertisements; autoconfigure using them. + + Functional default: enabled if local forwarding is disabled. + disabled if local forwarding is enabled. + +accept_redirects - BOOLEAN + Accept Redirects. + + Functional default: enabled if local forwarding is disabled. + disabled if local forwarding is enabled. + +autoconf - BOOLEAN + Autoconfigure addresses using Prefix Information in Router + Advertisements. + + Functional default: enabled if accept_ra is enabled. + disabled if accept_ra is disabled. + +dad_transmits - INTEGER + The amount of Duplicate Address Detection probes to send. + Default: 1 + +forwarding - BOOLEAN + Configure interface-specific Host/Router behaviour. + + Note: It is recommended to have the same setting on all + interfaces; mixed router/host scenarios are rather uncommon. + + FALSE: + + By default, Host behaviour is assumed. This means: + + 1. IsRouter flag is not set in Neighbour Advertisements. + 2. Router Solicitations are being sent when necessary. + 3. If accept_ra is TRUE (default), accept Router + Advertisements (and do autoconfiguration). + 4. If accept_redirects is TRUE (default), accept Redirects. + + TRUE: + + If local forwarding is enabled, Router behaviour is assumed. + This means exactly the reverse from the above: + + 1. IsRouter flag is set in Neighbour Advertisements. + 2. Router Solicitations are not sent. + 3. Router Advertisements are ignored. + 4. Redirects are ignored. + + Default: FALSE if global forwarding is disabled (default), + otherwise TRUE. + +hop_limit - INTEGER + Default Hop Limit to set. + Default: 64 + +mtu - INTEGER + Default Maximum Transfer Unit + Default: 1280 (IPv6 required minimum) + +router_solicitation_delay - INTEGER + Number of seconds to wait after interface is brought up + before sending Router Solicitations. + Default: 1 + +router_solicitation_interval - INTEGER + Number of seconds to wait between Router Solicitations. + Default: 4 + +router_solicitations - INTEGER + Number of Router Solicitations to send until assuming no + routers are present. + Default: 3 + +use_tempaddr - INTEGER + Preference for Privacy Extensions (RFC3041). + <= 0 : disable Privacy Extensions + == 1 : enable Privacy Extensions, but prefer public + addresses over temporary addresses. + > 1 : enable Privacy Extensions and prefer temporary + addresses over public addresses. + Default: 0 (for most devices) + -1 (for point-to-point devices and loopback devices) + +temp_valid_lft - INTEGER + valid lifetime (in seconds) for temporary addresses. + Default: 604800 (7 days) + +temp_prefered_lft - INTEGER + Preferred lifetime (in seconds) for temporary addresses. + Default: 86400 (1 day) + +max_desync_factor - INTEGER + Maximum value for DESYNC_FACTOR, which is a random value + that ensures that clients don't synchronize with each + other and generate new addresses at exactly the same time. + value is in seconds. + Default: 600 + +regen_max_retry - INTEGER + Number of attempts before give up attempting to generate + valid temporary addresses. + Default: 5 + +max_addresses - INTEGER + Number of maximum addresses per interface. 0 disables limitation. + It is recommended not set too large value (or 0) because it would + be too easy way to crash kernel to allow to create too much of + autoconfigured addresses. + Default: 16 + +icmp/*: +ratelimit - INTEGER + Limit the maximal rates for sending ICMPv6 packets. + 0 to disable any limiting, otherwise the maximal rate in jiffies(1) + Default: 100 + + +IPv6 Update by: +Pekka Savola <pekkas@netcore.fi> +YOSHIFUJI Hideaki / USAGI Project <yoshfuji@linux-ipv6.org> + + +/proc/sys/net/bridge/* Variables: + +bridge-nf-call-arptables - BOOLEAN + 1 : pass bridged ARP traffic to arptables' FORWARD chain. + 0 : disable this. + Default: 1 + +bridge-nf-call-iptables - BOOLEAN + 1 : pass bridged IPv4 traffic to iptables' chains. + 0 : disable this. + Default: 1 + +bridge-nf-call-ip6tables - BOOLEAN + 1 : pass bridged IPv6 traffic to ip6tables' chains. + 0 : disable this. + Default: 1 + +bridge-nf-filter-vlan-tagged - BOOLEAN + 1 : pass bridged vlan-tagged ARP/IP traffic to arptables/iptables. + 0 : disable this. + Default: 1 + + +UNDOCUMENTED: + +dev_weight FIXME +discovery_slots FIXME +discovery_timeout FIXME +fast_poll_increase FIXME +ip6_queue_maxlen FIXME +lap_keepalive_time FIXME +lo_cong FIXME +max_baud_rate FIXME +max_dgram_qlen FIXME +max_noreply_time FIXME +max_tx_data_size FIXME +max_tx_window FIXME +min_tx_turn_time FIXME +mod_cong FIXME +no_cong FIXME +no_cong_thresh FIXME +slot_timeout FIXME +warn_noreply_time FIXME + +$Id: ip-sysctl.txt,v 1.20 2001/12/13 09:00:18 davem Exp $ |