diff options
Diffstat (limited to 'Documentation/networking/sis900.txt')
| -rw-r--r-- | Documentation/networking/sis900.txt | 257 |
1 files changed, 0 insertions, 257 deletions
diff --git a/Documentation/networking/sis900.txt b/Documentation/networking/sis900.txt deleted file mode 100644 index bddffd7385a..00000000000 --- a/Documentation/networking/sis900.txt +++ /dev/null @@ -1,257 +0,0 @@ - -SiS 900/7016 Fast Ethernet Device Driver - -Ollie Lho - -Lei Chun Chang - - Copyright © 1999 by Silicon Integrated System Corp. - - This document gives some information on installation and usage of SiS - 900/7016 device driver under Linux. - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or (at - your option) any later version. - - This program is distributed in the hope that it will be useful, but - WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 - USA - _________________________________________________________________ - - Table of Contents - 1. Introduction - 2. Changes - 3. Tested Environment - 4. Files in This Package - 5. Installation - - Building the driver as loadable module - Building the driver into kernel - - 6. Known Problems and Bugs - 7. Revision History - 8. Acknowledgements - _________________________________________________________________ - -Chapter 1. Introduction - - This document describes the revision 1.06 and 1.07 of SiS 900/7016 - Fast Ethernet device driver under Linux. The driver is developed by - Silicon Integrated System Corp. and distributed freely under the GNU - General Public License (GPL). The driver can be compiled as a loadable - module and used under Linux kernel version 2.2.x. (rev. 1.06) With - minimal changes, the driver can also be used under 2.3.x and 2.4.x - kernel (rev. 1.07), please see Chapter 5. If you are intended to use - the driver for earlier kernels, you are on your own. - - The driver is tested with usual TCP/IP applications including FTP, - Telnet, Netscape etc. and is used constantly by the developers. - - Please send all comments/fixes/questions to Lei-Chun Chang. - _________________________________________________________________ - -Chapter 2. Changes - - Changes made in Revision 1.07 - - 1. Separation of sis900.c and sis900.h in order to move most constant - definition to sis900.h (many of those constants were corrected) - 2. Clean up PCI detection, the pci-scan from Donald Becker were not - used, just simple pci_find_*. - 3. MII detection is modified to support multiple mii transceiver. - 4. Bugs in read_eeprom, mdio_* were removed. - 5. Lot of sis900 irrelevant comments were removed/changed and more - comments were added to reflect the real situation. - 6. Clean up of physical/virtual address space mess in buffer - descriptors. - 7. Better transmit/receive error handling. - 8. The driver now uses zero-copy single buffer management scheme to - improve performance. - 9. Names of variables were changed to be more consistent. - 10. Clean up of auo-negotiation and timer code. - 11. Automatic detection and change of PHY on the fly. - 12. Bug in mac probing fixed. - 13. Fix 630E equalier problem by modifying the equalizer workaround - rule. - 14. Support for ICS1893 10/100 Interated PHYceiver. - 15. Support for media select by ifconfig. - 16. Added kernel-doc extratable documentation. - _________________________________________________________________ - -Chapter 3. Tested Environment - - This driver is developed on the following hardware - - * Intel Celeron 500 with SiS 630 (rev 02) chipset - * SiS 900 (rev 01) and SiS 7016/7014 Fast Ethernet Card - - and tested with these software environments - - * Red Hat Linux version 6.2 - * Linux kernel version 2.4.0 - * Netscape version 4.6 - * NcFTP 3.0.0 beta 18 - * Samba version 2.0.3 - _________________________________________________________________ - -Chapter 4. Files in This Package - - In the package you can find these files: - - sis900.c - Driver source file in C - - sis900.h - Header file for sis900.c - - sis900.sgml - DocBook SGML source of the document - - sis900.txt - Driver document in plain text - _________________________________________________________________ - -Chapter 5. Installation - - Silicon Integrated System Corp. is cooperating closely with core Linux - Kernel developers. The revisions of SiS 900 driver are distributed by - the usuall channels for kernel tar files and patches. Those kernel tar - files for official kernel and patches for kernel pre-release can be - download at official kernel ftp site and its mirrors. The 1.06 - revision can be found in kernel version later than 2.3.15 and - pre-2.2.14, and 1.07 revision can be found in kernel version 2.4.0. If - you have no prior experience in networking under Linux, please read - Ethernet HOWTO and Networking HOWTO available from Linux Documentation - Project (LDP). - - The driver is bundled in release later than 2.2.11 and 2.3.15 so this - is the most easy case. Be sure you have the appropriate packages for - compiling kernel source. Those packages are listed in Document/Changes - in kernel source distribution. If you have to install the driver other - than those bundled in kernel release, you should have your driver file - sis900.c and sis900.h copied into /usr/src/linux/drivers/net/ first. - There are two alternative ways to install the driver - _________________________________________________________________ - -Building the driver as loadable module - - To build the driver as a loadable kernel module you have to - reconfigure the kernel to activate network support by - -make menuconfig - - Choose "Loadable module support --->", then select "Enable loadable - module support". - - Choose "Network Device Support --->", select "Ethernet (10 or - 100Mbit)". Then select "EISA, VLB, PCI and on board controllers", and - choose "SiS 900/7016 PCI Fast Ethernet Adapter support" to "M". - - After reconfiguring the kernel, you can make the driver module by - -make modules - - The driver should be compiled with no errors. After compiling the - driver, the driver can be installed to proper place by - -make modules_install - - Load the driver into kernel by - -insmod sis900 - - When loading the driver into memory, some information message can be - view by - -dmesg - - or -cat /var/log/message - - If the driver is loaded properly you will have messages similar to - this: - -sis900.c: v1.07.06 11/07/2000 -eth0: SiS 900 PCI Fast Ethernet at 0xd000, IRQ 10, 00:00:e8:83:7f:a4. -eth0: SiS 900 Internal MII PHY transceiver found at address 1. -eth0: Using SiS 900 Internal MII PHY as default - - showing the version of the driver and the results of probing routine. - - Once the driver is loaded, network can be brought up by - -/sbin/ifconfig eth0 IPADDR broadcast BROADCAST netmask NETMASK media TYPE - - where IPADDR, BROADCAST, NETMASK are your IP address, broadcast - address and netmask respectively. TYPE is used to set medium type used - by the device. Typical values are "10baseT"(twisted-pair 10Mbps - Ethernet) or "100baseT" (twisted-pair 100Mbps Ethernet). For more - information on how to configure network interface, please refer to - Networking HOWTO. - - The link status is also shown by kernel messages. For example, after - the network interface is activated, you may have the message: - -eth0: Media Link On 100mbps full-duplex - - If you try to unplug the twist pair (TP) cable you will get - -eth0: Media Link Off - - indicating that the link is failed. - _________________________________________________________________ - -Building the driver into kernel - - If you want to make the driver into kernel, choose "Y" rather than "M" - on "SiS 900/7016 PCI Fast Ethernet Adapter support" when configuring - the kernel. Build the kernel image in the usual way - -make clean - -make bzlilo - - Next time the system reboot, you have the driver in memory. - _________________________________________________________________ - -Chapter 6. Known Problems and Bugs - - There are some known problems and bugs. If you find any other bugs - please mail to lcchang@sis.com.tw - - 1. AM79C901 HomePNA PHY is not thoroughly tested, there may be some - bugs in the "on the fly" change of transceiver. - 2. A bug is hidden somewhere in the receive buffer management code, - the bug causes NULL pointer reference in the kernel. This fault is - caught before bad things happen and reported with the message: - eth0: NULL pointer encountered in Rx ring, skipping which can be - viewed with dmesg or cat /var/log/message. - 3. The media type change from 10Mbps to 100Mbps twisted-pair ethernet - by ifconfig causes the media link down. - _________________________________________________________________ - -Chapter 7. Revision History - - * November 13, 2000, Revision 1.07, seventh release, 630E problem - fixed and further clean up. - * November 4, 1999, Revision 1.06, Second release, lots of clean up - and optimization. - * August 8, 1999, Revision 1.05, Initial Public Release - _________________________________________________________________ - -Chapter 8. Acknowledgements - - This driver was originally derived form Donald Becker's pci-skeleton - and rtl8139 drivers. Donald also provided various suggestion regarded - with improvements made in revision 1.06. - - The 1.05 revision was created by Jim Huang, AMD 79c901 support was - added by Chin-Shan Li. |