diff options
Diffstat (limited to 'Documentation/networking/smctr.txt')
| -rw-r--r-- | Documentation/networking/smctr.txt | 66 |
1 files changed, 0 insertions, 66 deletions
diff --git a/Documentation/networking/smctr.txt b/Documentation/networking/smctr.txt deleted file mode 100644 index 9af25b810c1..00000000000 --- a/Documentation/networking/smctr.txt +++ /dev/null @@ -1,66 +0,0 @@ -Text File for the SMC TokenCard TokenRing Linux driver (smctr.c). - By Jay Schulist <jschlst@samba.org> - -The Linux SMC Token Ring driver works with the SMC TokenCard Elite (8115T) -ISA and SMC TokenCard Elite/A (8115T/A) MCA adapters. - -Latest information on this driver can be obtained on the Linux-SNA WWW site. -Please point your browser to: http://www.linux-sna.org - -This driver is rather simple to use. Select Y to Token Ring adapter support -in the kernel configuration. A choice for SMC Token Ring adapters will -appear. This drives supports all SMC ISA/MCA adapters. Choose this -option. I personally recommend compiling the driver as a module (M), but if you -you would like to compile it statically answer Y instead. - -This driver supports multiple adapters without the need to load multiple copies -of the driver. You should be able to load up to 7 adapters without any kernel -modifications, if you are in need of more please contact the maintainer of this -driver. - -Load the driver either by lilo/loadlin or as a module. When a module using the -following command will suffice for most: - -# modprobe smctr -smctr.c: v1.00 12/6/99 by jschlst@samba.org -tr0: SMC TokenCard 8115T at Io 0x300, Irq 10, Rom 0xd8000, Ram 0xcc000. - -Now just setup the device via ifconfig and set and routes you may have. After -this you are ready to start sending some tokens. - -Errata: -1). For anyone wondering where to pick up the SMC adapters please browse - to http://www.smc.com - -2). If you are the first/only Token Ring Client on a Token Ring LAN, please - specify the ringspeed with the ringspeed=[4/16] module option. If no - ringspeed is specified the driver will attempt to autodetect the ring - speed and/or if the adapter is the first/only station on the ring take - the appropriate actions. - - NOTE: Default ring speed is 16MB UTP. - -3). PnP support for this adapter sucks. I recommend hard setting the - IO/MEM/IRQ by the jumpers on the adapter. If this is not possible - load the module with the following io=[ioaddr] mem=[mem_addr] - irq=[irq_num]. - - The following IRQ, IO, and MEM settings are supported. - - IO ports: - 0x200, 0x220, 0x240, 0x260, 0x280, 0x2A0, 0x2C0, 0x2E0, 0x300, - 0x320, 0x340, 0x360, 0x380. - - IRQs: - 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13, 14, 15 - - Memory addresses: - 0xA0000, 0xA4000, 0xA8000, 0xAC000, 0xB0000, 0xB4000, - 0xB8000, 0xBC000, 0xC0000, 0xC4000, 0xC8000, 0xCC000, - 0xD0000, 0xD4000, 0xD8000, 0xDC000, 0xE0000, 0xE4000, - 0xE8000, 0xEC000, 0xF0000, 0xF4000, 0xF8000, 0xFC000 - -This driver is under the GNU General Public License. Its Firmware image is -included as an initialized C-array and is licensed by SMC to the Linux -users of this driver. However no warranty about its fitness is expressed or -implied by SMC. |