diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/gen_stats.txt | 4 | ||||
| -rw-r--r-- | Documentation/networking/packet_mmap.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/sk98lin.txt | 8 | ||||
| -rw-r--r-- | Documentation/networking/vortex.txt | 4 | ||||
| -rw-r--r-- | Documentation/networking/wan-router.txt | 8 |
5 files changed, 13 insertions, 13 deletions
diff --git a/Documentation/networking/gen_stats.txt b/Documentation/networking/gen_stats.txt index ae54c828f4d..70e6275b757 100644 --- a/Documentation/networking/gen_stats.txt +++ b/Documentation/networking/gen_stats.txt @@ -79,8 +79,8 @@ Rate Estimator: 0) Prepare an estimator attribute. Most likely this would be in user space. The value of this TLV should contain a tc_estimator structure. - As usual, such a TLV nees to be 32 bit aligned and therefore the - length needs to be appropriately set etc. The estimator interval + As usual, such a TLV needs to be 32 bit aligned and therefore the + length needs to be appropriately set, etc. The estimator interval and ewma log need to be converted to the appropriate values. tc_estimator.c::tc_setup_estimator() is advisable to be used as the conversion routine. It does a few clever things. It takes a time diff --git a/Documentation/networking/packet_mmap.txt b/Documentation/networking/packet_mmap.txt index a87d4a8b395..12a008a5c22 100644 --- a/Documentation/networking/packet_mmap.txt +++ b/Documentation/networking/packet_mmap.txt @@ -278,7 +278,7 @@ an i386 kernel's memory size is limited to 1GiB. All memory allocations are not freed until the socket is closed. The memory allocations are done with GFP_KERNEL priority, this basically means that the allocation can wait and swap other process' memory in order to allocate -the nececessary memory, so normally limits can be reached. +the necessary memory, so normally limits can be reached. Other constraints ------------------- diff --git a/Documentation/networking/sk98lin.txt b/Documentation/networking/sk98lin.txt index b8bc7dd3d28..817fc113d93 100644 --- a/Documentation/networking/sk98lin.txt +++ b/Documentation/networking/sk98lin.txt @@ -180,7 +180,7 @@ To set the driver parameters in this file, proceed as follows: 1. Insert a line of the form : options sk98lin ... For "...", the same syntax is required as described for the command - line paramaters of modprobe below. + line parameters of modprobe below. 2. To activate the new parameters, either reboot your computer or unload and reload the driver. @@ -364,9 +364,9 @@ Parameter: IntsPerSec Values: 30...40000 (interrupts per second) Default: 2000 -This parameter is only used, if either static or dynamic interrupt moderation -is used on a network adapter card. Using this paramter if no moderation is -applied, will lead to no action performed. +This parameter is only used if either static or dynamic interrupt moderation +is used on a network adapter card. Using this parameter if no moderation is +applied will lead to no action performed. This parameter determines the length of any interrupt moderation interval. Assuming that static interrupt moderation is to be used, an 'IntsPerSec' diff --git a/Documentation/networking/vortex.txt b/Documentation/networking/vortex.txt index 6091e5f6794..6356d3faed3 100644 --- a/Documentation/networking/vortex.txt +++ b/Documentation/networking/vortex.txt @@ -359,13 +359,13 @@ steps you should take: Eliminate some variables: try different cards, different computers, different cables, different ports on the switch/hub, - different versions of the kernel or ofthe driver, etc. + different versions of the kernel or of the driver, etc. - OK, it's a driver problem. You need to generate a report. Typically this is an email to the maintainer and/or linux-net@vger.kernel.org. The maintainer's - email address will be inthe driver source or in the MAINTAINERS file. + email address will be in the driver source or in the MAINTAINERS file. - The contents of your report will vary a lot depending upon the problem. If it's a kernel crash then you should refer to the diff --git a/Documentation/networking/wan-router.txt b/Documentation/networking/wan-router.txt index 37e42fed748..0cf65414763 100644 --- a/Documentation/networking/wan-router.txt +++ b/Documentation/networking/wan-router.txt @@ -214,7 +214,7 @@ PRODUCT COMPONENTS AND RELATED FILES /usr/local/wanrouter/patches/kdrivers: Sources of the latest WANPIPE device drivers. These are used to UPGRADE the linux kernel to the newest - version if the kernel source has already been pathced with + version if the kernel source has already been patched with WANPIPE drivers. /usr/local/wanrouter/samples: @@ -438,7 +438,7 @@ beta1-2.1.5 Nov 15 2000 2.2.X kernels only o Secured the driver UDP debugging calls - - All illegal netowrk debugging calls are reported to + - All illegal network debugging calls are reported to the log. - Defined a set of allowed commands, all other denied. @@ -451,7 +451,7 @@ beta1-2.1.5 Nov 15 2000 o Keyboard Led Monitor/Debugger - A new utilty /usr/sbin/wpkbdmon uses keyboard leds - to convey operatinal statistic information of the + to convey operational statistic information of the Sangoma WANPIPE cards. NUM_LOCK = Line State (On=connected, Off=disconnected) CAPS_LOCK = Tx data (On=transmitting, Off=no tx data) @@ -470,7 +470,7 @@ beta1-2.1.5 Nov 15 2000 o Fixed the Frame Relay and Chdlc network interfaces so they are compatible with libpcap libraries. Meaning, tcpdump, snort, ethereal, and all other packet sniffers and debuggers work on - all WANPIPE netowrk interfaces. + all WANPIPE network interfaces. - Set the network interface encoding type to ARPHRD_PPP. This tell the sniffers that data obtained from the network interface is in pure IP format. |