diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/bonding.txt | 83 |
1 files changed, 71 insertions, 12 deletions
diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index 5dc638791d9..25d2f4141d2 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -49,7 +49,8 @@ Table of Contents 3.3 Configuring Bonding Manually with Ifenslave 3.3.1 Configuring Multiple Bonds Manually 3.4 Configuring Bonding Manually via Sysfs -3.5 Overriding Configuration for Special Cases +3.5 Configuration with Interfaces Support +3.6 Overriding Configuration for Special Cases 4. Querying Bonding Configuration 4.1 Bonding Configuration @@ -161,8 +162,8 @@ onwards) do not have /usr/include/linux symbolically linked to the default kernel source include directory. SECOND IMPORTANT NOTE: - If you plan to configure bonding using sysfs, you do not need -to use ifenslave. + If you plan to configure bonding using sysfs or using the +/etc/network/interfaces file, you do not need to use ifenslave. 2. Bonding Driver Options ========================= @@ -779,22 +780,26 @@ resend_igmp You can configure bonding using either your distro's network initialization scripts, or manually using either ifenslave or the -sysfs interface. Distros generally use one of two packages for the -network initialization scripts: initscripts or sysconfig. Recent -versions of these packages have support for bonding, while older +sysfs interface. Distros generally use one of three packages for the +network initialization scripts: initscripts, sysconfig or interfaces. +Recent versions of these packages have support for bonding, while older versions do not. We will first describe the options for configuring bonding for -distros using versions of initscripts and sysconfig with full or -partial support for bonding, then provide information on enabling +distros using versions of initscripts, sysconfig and interfaces with full +or partial support for bonding, then provide information on enabling bonding without support from the network initialization scripts (i.e., older versions of initscripts or sysconfig). - If you're unsure whether your distro uses sysconfig or -initscripts, or don't know if it's new enough, have no fear. + If you're unsure whether your distro uses sysconfig, +initscripts or interfaces, or don't know if it's new enough, have no fear. Determining this is fairly straightforward. - First, issue the command: + First, look for a file called interfaces in /etc/network directory. +If this file is present in your system, then your system use interfaces. See +Configuration with Interfaces Support. + + Else, issue the command: $ rpm -qf /sbin/ifup @@ -1327,8 +1332,62 @@ echo 2000 > /sys/class/net/bond1/bonding/arp_interval echo +eth2 > /sys/class/net/bond1/bonding/slaves echo +eth3 > /sys/class/net/bond1/bonding/slaves -3.5 Overriding Configuration for Special Cases +3.5 Configuration with Interfaces Support +----------------------------------------- + + This section applies to distros which use /etc/network/interfaces file +to describe network interface configuration, most notably Debian and it's +derivatives. + + The ifup and ifdown commands on Debian don't support bonding out of +the box. The ifenslave-2.6 package should be installed to provide bonding +support. Once installed, this package will provide bond-* options to be used +into /etc/network/interfaces. + + Note that ifenslave-2.6 package will load the bonding module and use +the ifenslave command when appropriate. + +Example Configurations +---------------------- + +In /etc/network/interfaces, the following stanza will configure bond0, in +active-backup mode, with eth0 and eth1 as slaves. + +auto bond0 +iface bond0 inet dhcp + bond-slaves eth0 eth1 + bond-mode active-backup + bond-miimon 100 + bond-primary eth0 eth1 + +If the above configuration doesn't work, you might have a system using +upstart for system startup. This is most notably true for recent +Ubuntu versions. The following stanza in /etc/network/interfaces will +produce the same result on those systems. + +auto bond0 +iface bond0 inet dhcp + bond-slaves none + bond-mode active-backup + bond-miimon 100 + +auto eth0 +iface eth0 inet manual + bond-master bond0 + bond-primary eth0 eth1 + +auto eth1 +iface eth1 inet manual + bond-master bond0 + bond-primary eth0 eth1 + +For a full list of bond-* supported options in /etc/network/interfaces and some +more advanced examples tailored to you particular distros, see the files in +/usr/share/doc/ifenslave-2.6. + +3.6 Overriding Configuration for Special Cases ---------------------------------------------- + When using the bonding driver, the physical port which transmits a frame is typically selected by the bonding driver, and is not relevant to the user or system administrator. The output port is simply selected using the policies of |