diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/baycom.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/bonding.txt | 43 | ||||
| -rw-r--r-- | Documentation/networking/dl2k.txt | 11 | ||||
| -rw-r--r-- | Documentation/networking/e100.txt | 6 | ||||
| -rw-r--r-- | Documentation/networking/ipv6.txt | 6 | ||||
| -rw-r--r-- | Documentation/networking/ixgb.txt | 6 | ||||
| -rw-r--r-- | Documentation/networking/ltpc.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/vortex.txt | 6 |
8 files changed, 38 insertions, 44 deletions
diff --git a/Documentation/networking/baycom.txt b/Documentation/networking/baycom.txt index 4e68849d563..688f18fd446 100644 --- a/Documentation/networking/baycom.txt +++ b/Documentation/networking/baycom.txt @@ -93,7 +93,7 @@ Every time a driver is inserted into the kernel, it has to know which modems it should access at which ports. This can be done with the setbaycom utility. If you are only using one modem, you can also configure the driver from the insmod command line (or by means of an option line in -/etc/modprobe.conf). +/etc/modprobe.d/*.conf). Examples: modprobe baycom_ser_fdx mode="ser12*" iobase=0x3f8 irq=4 diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index 080ad26690a..d5e86981404 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -173,9 +173,8 @@ bonding module at load time, or are specified via sysfs. Module options may be given as command line arguments to the insmod or modprobe command, but are usually specified in either the -/etc/modules.conf or /etc/modprobe.conf configuration file, or in a -distro-specific configuration file (some of which are detailed in the next -section). +/etc/modrobe.d/*.conf configuration files, or in a distro-specific +configuration file (some of which are detailed in the next section). Details on bonding support for sysfs is provided in the "Configuring Bonding Manually via Sysfs" section, below. @@ -1021,7 +1020,7 @@ ifcfg-bondX files. Because the sysconfig scripts supply the bonding module options in the ifcfg-bondX file, it is not necessary to add them to -the system /etc/modules.conf or /etc/modprobe.conf configuration file. +the system /etc/modules.d/*.conf configuration files. 3.2 Configuration with Initscripts Support ------------------------------------------ @@ -1098,15 +1097,13 @@ queried targets, e.g., arp_ip_target=+192.168.1.1 arp_ip_target=+192.168.1.2 is the proper syntax to specify multiple targets. When specifying -options via BONDING_OPTS, it is not necessary to edit /etc/modules.conf or -/etc/modprobe.conf. +options via BONDING_OPTS, it is not necessary to edit /etc/modprobe.d/*.conf. For even older versions of initscripts that do not support -BONDING_OPTS, it is necessary to edit /etc/modules.conf (or -/etc/modprobe.conf, depending upon your distro) to load the bonding module -with your desired options when the bond0 interface is brought up. The -following lines in /etc/modules.conf (or modprobe.conf) will load the -bonding module, and select its options: +BONDING_OPTS, it is necessary to edit /etc/modprobe.d/*.conf, depending upon +your distro) to load the bonding module with your desired options when the +bond0 interface is brought up. The following lines in /etc/modprobe.d/*.conf +will load the bonding module, and select its options: alias bond0 bonding options bond0 mode=balance-alb miimon=100 @@ -1152,7 +1149,7 @@ knowledge of bonding. One such distro is SuSE Linux Enterprise Server version 8. The general method for these systems is to place the bonding -module parameters into /etc/modules.conf or /etc/modprobe.conf (as +module parameters into a config file in /etc/modprobe.d/ (as appropriate for the installed distro), then add modprobe and/or ifenslave commands to the system's global init script. The name of the global init script differs; for sysconfig, it is @@ -1228,7 +1225,7 @@ network initialization scripts. specify a different name for each instance (the module loading system requires that every loaded module, even multiple instances of the same module, have a unique name). This is accomplished by supplying multiple -sets of bonding options in /etc/modprobe.conf, for example: +sets of bonding options in /etc/modprobe.d/*.conf, for example: alias bond0 bonding options bond0 -o bond0 mode=balance-rr miimon=100 @@ -1793,8 +1790,8 @@ route additions may cause trouble. On systems with network configuration scripts that do not associate physical devices directly with network interface names (so that the same physical device always has the same "ethX" name), it may -be necessary to add some special logic to either /etc/modules.conf or -/etc/modprobe.conf (depending upon which is installed on the system). +be necessary to add some special logic to config files in +/etc/modprobe.d/. For example, given a modules.conf containing the following: @@ -1821,20 +1818,16 @@ add above bonding e1000 tg3 bonding is loaded. This command is fully documented in the modules.conf manual page. - On systems utilizing modprobe.conf (or modprobe.conf.local), -an equivalent problem can occur. In this case, the following can be -added to modprobe.conf (or modprobe.conf.local, as appropriate), as -follows (all on one line; it has been split here for clarity): + On systems utilizing modprobe an equivalent problem can occur. +In this case, the following can be added to config files in +/etc/modprobe.d/ as: install bonding /sbin/modprobe tg3; /sbin/modprobe e1000; /sbin/modprobe --ignore-install bonding - This will, when loading the bonding module, rather than -performing the normal action, instead execute the provided command. -This command loads the device drivers in the order needed, then calls -modprobe with --ignore-install to cause the normal action to then take -place. Full documentation on this can be found in the modprobe.conf -and modprobe manual pages. + This will load tg3 and e1000 modules before loading the bonding one. +Full documentation on this can be found in the modprobe.d and modprobe +manual pages. 8.3. Painfully Slow Or No Failed Link Detection By Miimon --------------------------------------------------------- diff --git a/Documentation/networking/dl2k.txt b/Documentation/networking/dl2k.txt index 10e8490fa40..cba74f7a3ab 100644 --- a/Documentation/networking/dl2k.txt +++ b/Documentation/networking/dl2k.txt @@ -45,12 +45,13 @@ Now eth0 should active, you can test it by "ping" or get more information by "ifconfig". If tested ok, continue the next step. 4. cp dl2k.ko /lib/modules/`uname -r`/kernel/drivers/net -5. Add the following line to /etc/modprobe.conf: +5. Add the following line to /etc/modprobe.d/dl2k.conf: alias eth0 dl2k -6. Run "netconfig" or "netconf" to create configuration script ifcfg-eth0 +6. Run depmod to updated module indexes. +7. Run "netconfig" or "netconf" to create configuration script ifcfg-eth0 located at /etc/sysconfig/network-scripts or create it manually. [see - Configuration Script Sample] -7. Driver will automatically load and configure at next boot time. +8. Driver will automatically load and configure at next boot time. Compiling the Driver ==================== @@ -154,8 +155,8 @@ Installing the Driver ----------------- 1. Copy dl2k.o to the network modules directory, typically /lib/modules/2.x.x-xx/net or /lib/modules/2.x.x/kernel/drivers/net. - 2. Locate the boot module configuration file, most commonly modprobe.conf - or modules.conf (for 2.4) in the /etc directory. Add the following lines: + 2. Locate the boot module configuration file, most commonly in the + /etc/modprobe.d/ directory. Add the following lines: alias ethx dl2k options dl2k <optional parameters> diff --git a/Documentation/networking/e100.txt b/Documentation/networking/e100.txt index 162f323a7a1..fcb6c71cdb6 100644 --- a/Documentation/networking/e100.txt +++ b/Documentation/networking/e100.txt @@ -94,8 +94,8 @@ Additional Configurations Configuring a network driver to load properly when the system is started is distribution dependent. Typically, the configuration process involves adding - an alias line to /etc/modules.conf or /etc/modprobe.conf as well as editing - other system startup scripts and/or configuration files. Many popular Linux + an alias line to /etc/modprobe.d/*.conf as well as editing other system + startup scripts and/or configuration files. Many popular Linux distributions ship with tools to make these changes for you. To learn the proper way to configure a network device for your system, refer to your distribution documentation. If during this process you are asked for the @@ -103,7 +103,7 @@ Additional Configurations PRO/100 Family of Adapters is e100. As an example, if you install the e100 driver for two PRO/100 adapters - (eth0 and eth1), add the following to modules.conf or modprobe.conf: + (eth0 and eth1), add the following to a configuraton file in /etc/modprobe.d/ alias eth0 e100 alias eth1 e100 diff --git a/Documentation/networking/ipv6.txt b/Documentation/networking/ipv6.txt index 9fd7e21296c..6cd74fa5535 100644 --- a/Documentation/networking/ipv6.txt +++ b/Documentation/networking/ipv6.txt @@ -2,9 +2,9 @@ Options for the ipv6 module are supplied as parameters at load time. Module options may be given as command line arguments to the insmod -or modprobe command, but are usually specified in either the -/etc/modules.conf or /etc/modprobe.conf configuration file, or in a -distro-specific configuration file. +or modprobe command, but are usually specified in either +/etc/modules.d/*.conf configuration files, or in a distro-specific +configuration file. The available ipv6 module parameters are listed below. If a parameter is not specified the default value is used. diff --git a/Documentation/networking/ixgb.txt b/Documentation/networking/ixgb.txt index e196f16df31..d75a1f9565b 100644 --- a/Documentation/networking/ixgb.txt +++ b/Documentation/networking/ixgb.txt @@ -274,9 +274,9 @@ Additional Configurations ------------------------------------------------- Configuring a network driver to load properly when the system is started is distribution dependent. Typically, the configuration process involves adding - an alias line to /etc/modprobe.conf as well as editing other system startup - scripts and/or configuration files. Many popular Linux distributions ship - with tools to make these changes for you. To learn the proper way to + an alias line to files in /etc/modprobe.d/ as well as editing other system + startup scripts and/or configuration files. Many popular Linux distributions + ship with tools to make these changes for you. To learn the proper way to configure a network device for your system, refer to your distribution documentation. If during this process you are asked for the driver or module name, the name for the Linux Base Driver for the Intel 10GbE Family of diff --git a/Documentation/networking/ltpc.txt b/Documentation/networking/ltpc.txt index fe2a9129d95..0bf3220c715 100644 --- a/Documentation/networking/ltpc.txt +++ b/Documentation/networking/ltpc.txt @@ -25,7 +25,7 @@ the driver will try to determine them itself. If you load the driver as a module, you can pass the parameters "io=", "irq=", and "dma=" on the command line with insmod or modprobe, or add -them as options in /etc/modprobe.conf: +them as options in a configuration file in /etc/modprobe.d/ directory: alias lt0 ltpc # autoload the module when the interface is configured options ltpc io=0x240 irq=9 dma=1 diff --git a/Documentation/networking/vortex.txt b/Documentation/networking/vortex.txt index bd70976b816..b4038ffb3bc 100644 --- a/Documentation/networking/vortex.txt +++ b/Documentation/networking/vortex.txt @@ -67,8 +67,8 @@ Module parameters ================= There are several parameters which may be provided to the driver when -its module is loaded. These are usually placed in /etc/modprobe.conf -(/etc/modules.conf in 2.4). Example: +its module is loaded. These are usually placed in /etc/modprobe.d/*.conf +configuretion files. Example: options 3c59x debug=3 rx_copybreak=300 @@ -425,7 +425,7 @@ steps you should take: 1) Increase the debug level. Usually this is done via: a) modprobe driver debug=7 - b) In /etc/modprobe.conf (or /etc/modules.conf for 2.4): + b) In /etc/modprobe.d/driver.conf: options driver debug=7 2) Recreate the problem with the higher debug level, |