diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/ifenslave.c | 18 | ||||
| -rw-r--r-- | Documentation/networking/ip-sysctl.txt | 29 | ||||
| -rw-r--r-- | Documentation/networking/netdev-features.txt | 154 | ||||
| -rw-r--r-- | Documentation/networking/nfc.txt | 128 | ||||
| -rw-r--r-- | Documentation/networking/stmmac.txt | 200 |
5 files changed, 440 insertions, 89 deletions
diff --git a/Documentation/networking/ifenslave.c b/Documentation/networking/ifenslave.c index 2bac9618c34..65968fbf1e4 100644 --- a/Documentation/networking/ifenslave.c +++ b/Documentation/networking/ifenslave.c @@ -260,7 +260,7 @@ int main(int argc, char *argv[]) case 'V': opt_V++; exclusive++; break; case '?': - fprintf(stderr, usage_msg); + fprintf(stderr, "%s", usage_msg); res = 2; goto out; } @@ -268,13 +268,13 @@ int main(int argc, char *argv[]) /* options check */ if (exclusive > 1) { - fprintf(stderr, usage_msg); + fprintf(stderr, "%s", usage_msg); res = 2; goto out; } if (opt_v || opt_V) { - printf(version); + printf("%s", version); if (opt_V) { res = 0; goto out; @@ -282,14 +282,14 @@ int main(int argc, char *argv[]) } if (opt_u) { - printf(usage_msg); + printf("%s", usage_msg); res = 0; goto out; } if (opt_h) { - printf(usage_msg); - printf(help_msg); + printf("%s", usage_msg); + printf("%s", help_msg); res = 0; goto out; } @@ -309,7 +309,7 @@ int main(int argc, char *argv[]) goto out; } else { /* Just show usage */ - fprintf(stderr, usage_msg); + fprintf(stderr, "%s", usage_msg); res = 2; goto out; } @@ -320,7 +320,7 @@ int main(int argc, char *argv[]) master_ifname = *spp++; if (master_ifname == NULL) { - fprintf(stderr, usage_msg); + fprintf(stderr, "%s", usage_msg); res = 2; goto out; } @@ -339,7 +339,7 @@ int main(int argc, char *argv[]) if (slave_ifname == NULL) { if (opt_d || opt_c) { - fprintf(stderr, usage_msg); + fprintf(stderr, "%s", usage_msg); res = 2; goto out; } diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index bfe924217f2..db2a4067013 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -106,16 +106,6 @@ inet_peer_maxttl - INTEGER when the number of entries in the pool is very small). Measured in seconds. -inet_peer_gc_mintime - INTEGER - Minimum interval between garbage collection passes. This interval is - in effect under high memory pressure on the pool. - Measured in seconds. - -inet_peer_gc_maxtime - INTEGER - Minimum interval between garbage collection passes. This interval is - in effect under low (or absent) memory pressure on the pool. - Measured in seconds. - TCP variables: somaxconn - INTEGER @@ -394,7 +384,7 @@ tcp_rmem - vector of 3 INTEGERs: min, default, max min: Minimal size of receive buffer used by TCP sockets. It is guaranteed to each TCP socket, even under moderate memory pressure. - Default: 8K + Default: 1 page default: initial size of receive buffer used by TCP sockets. This value overrides net.core.rmem_default used by other protocols. @@ -483,7 +473,7 @@ tcp_window_scaling - BOOLEAN tcp_wmem - vector of 3 INTEGERs: min, default, max min: Amount of memory reserved for send buffers for TCP sockets. Each TCP socket has rights to use it due to fact of its birth. - Default: 4K + Default: 1 page default: initial size of send buffer used by TCP sockets. This value overrides net.core.wmem_default used by other protocols. @@ -553,13 +543,13 @@ udp_rmem_min - INTEGER Minimal size of receive buffer used by UDP sockets in moderation. Each UDP socket is able to use the size for receiving data, even if total pages of UDP sockets exceed udp_mem pressure. The unit is byte. - Default: 4096 + Default: 1 page udp_wmem_min - INTEGER Minimal size of send buffer used by UDP sockets in moderation. Each UDP socket is able to use the size for sending data, even if total pages of UDP sockets exceed udp_mem pressure. The unit is byte. - Default: 4096 + Default: 1 page CIPSOv4 Variables: @@ -1465,10 +1455,17 @@ sctp_mem - vector of 3 INTEGERs: min, pressure, max Default is calculated at boot time from amount of available memory. sctp_rmem - vector of 3 INTEGERs: min, default, max - See tcp_rmem for a description. + Only the first value ("min") is used, "default" and "max" are + ignored. + + min: Minimal size of receive buffer used by SCTP socket. + It is guaranteed to each SCTP socket (but not association) even + under moderate memory pressure. + + Default: 1 page sctp_wmem - vector of 3 INTEGERs: min, default, max - See tcp_wmem for a description. + Currently this tunable has no effect. addr_scope_policy - INTEGER Control IPv4 address scoping - draft-stewart-tsvwg-sctp-ipv4-00 diff --git a/Documentation/networking/netdev-features.txt b/Documentation/networking/netdev-features.txt new file mode 100644 index 00000000000..4b1c0dcef84 --- /dev/null +++ b/Documentation/networking/netdev-features.txt @@ -0,0 +1,154 @@ +Netdev features mess and how to get out from it alive +===================================================== + +Author: + Michał Mirosław <mirq-linux@rere.qmqm.pl> + + + + Part I: Feature sets +====================== + +Long gone are the days when a network card would just take and give packets +verbatim. Today's devices add multiple features and bugs (read: offloads) +that relieve an OS of various tasks like generating and checking checksums, +splitting packets, classifying them. Those capabilities and their state +are commonly referred to as netdev features in Linux kernel world. + +There are currently three sets of features relevant to the driver, and +one used internally by network core: + + 1. netdev->hw_features set contains features whose state may possibly + be changed (enabled or disabled) for a particular device by user's + request. This set should be initialized in ndo_init callback and not + changed later. + + 2. netdev->features set contains features which are currently enabled + for a device. This should be changed only by network core or in + error paths of ndo_set_features callback. + + 3. netdev->vlan_features set contains features whose state is inherited + by child VLAN devices (limits netdev->features set). This is currently + used for all VLAN devices whether tags are stripped or inserted in + hardware or software. + + 4. netdev->wanted_features set contains feature set requested by user. + This set is filtered by ndo_fix_features callback whenever it or + some device-specific conditions change. This set is internal to + networking core and should not be referenced in drivers. + + + + Part II: Controlling enabled features +======================================= + +When current feature set (netdev->features) is to be changed, new set +is calculated and filtered by calling ndo_fix_features callback +and netdev_fix_features(). If the resulting set differs from current +set, it is passed to ndo_set_features callback and (if the callback +returns success) replaces value stored in netdev->features. +NETDEV_FEAT_CHANGE notification is issued after that whenever current +set might have changed. + +The following events trigger recalculation: + 1. device's registration, after ndo_init returned success + 2. user requested changes in features state + 3. netdev_update_features() is called + +ndo_*_features callbacks are called with rtnl_lock held. Missing callbacks +are treated as always returning success. + +A driver that wants to trigger recalculation must do so by calling +netdev_update_features() while holding rtnl_lock. This should not be done +from ndo_*_features callbacks. netdev->features should not be modified by +driver except by means of ndo_fix_features callback. + + + + Part III: Implementation hints +================================ + + * ndo_fix_features: + +All dependencies between features should be resolved here. The resulting +set can be reduced further by networking core imposed limitations (as coded +in netdev_fix_features()). For this reason it is safer to disable a feature +when its dependencies are not met instead of forcing the dependency on. + +This callback should not modify hardware nor driver state (should be +stateless). It can be called multiple times between successive +ndo_set_features calls. + +Callback must not alter features contained in NETIF_F_SOFT_FEATURES or +NETIF_F_NEVER_CHANGE sets. The exception is NETIF_F_VLAN_CHALLENGED but +care must be taken as the change won't affect already configured VLANs. + + * ndo_set_features: + +Hardware should be reconfigured to match passed feature set. The set +should not be altered unless some error condition happens that can't +be reliably detected in ndo_fix_features. In this case, the callback +should update netdev->features to match resulting hardware state. +Errors returned are not (and cannot be) propagated anywhere except dmesg. +(Note: successful return is zero, >0 means silent error.) + + + + Part IV: Features +=================== + +For current list of features, see include/linux/netdev_features.h. +This section describes semantics of some of them. + + * Transmit checksumming + +For complete description, see comments near the top of include/linux/skbuff.h. + +Note: NETIF_F_HW_CSUM is a superset of NETIF_F_IP_CSUM + NETIF_F_IPV6_CSUM. +It means that device can fill TCP/UDP-like checksum anywhere in the packets +whatever headers there might be. + + * Transmit TCP segmentation offload + +NETIF_F_TSO_ECN means that hardware can properly split packets with CWR bit +set, be it TCPv4 (when NETIF_F_TSO is enabled) or TCPv6 (NETIF_F_TSO6). + + * Transmit DMA from high memory + +On platforms where this is relevant, NETIF_F_HIGHDMA signals that +ndo_start_xmit can handle skbs with frags in high memory. + + * Transmit scatter-gather + +Those features say that ndo_start_xmit can handle fragmented skbs: +NETIF_F_SG --- paged skbs (skb_shinfo()->frags), NETIF_F_FRAGLIST --- +chained skbs (skb->next/prev list). + + * Software features + +Features contained in NETIF_F_SOFT_FEATURES are features of networking +stack. Driver should not change behaviour based on them. + + * LLTX driver (deprecated for hardware drivers) + +NETIF_F_LLTX should be set in drivers that implement their own locking in +transmit path or don't need locking at all (e.g. software tunnels). +In ndo_start_xmit, it is recommended to use a try_lock and return +NETDEV_TX_LOCKED when the spin lock fails. The locking should also properly +protect against other callbacks (the rules you need to find out). + +Don't use it for new drivers. + + * netns-local device + +NETIF_F_NETNS_LOCAL is set for devices that are not allowed to move between +network namespaces (e.g. loopback). + +Don't use it in drivers. + + * VLAN challenged + +NETIF_F_VLAN_CHALLENGED should be set for devices which can't cope with VLAN +headers. Some drivers set this because the cards can't handle the bigger MTU. +[FIXME: Those cases could be fixed in VLAN code by allowing only reduced-MTU +VLANs. This may be not useful, though.] diff --git a/Documentation/networking/nfc.txt b/Documentation/networking/nfc.txt new file mode 100644 index 00000000000..b24c29bdae2 --- /dev/null +++ b/Documentation/networking/nfc.txt @@ -0,0 +1,128 @@ +Linux NFC subsystem +=================== + +The Near Field Communication (NFC) subsystem is required to standardize the +NFC device drivers development and to create an unified userspace interface. + +This document covers the architecture overview, the device driver interface +description and the userspace interface description. + +Architecture overview +--------------------- + +The NFC subsystem is responsible for: + - NFC adapters management; + - Polling for targets; + - Low-level data exchange; + +The subsystem is divided in some parts. The 'core' is responsible for +providing the device driver interface. On the other side, it is also +responsible for providing an interface to control operations and low-level +data exchange. + +The control operations are available to userspace via generic netlink. + +The low-level data exchange interface is provided by the new socket family +PF_NFC. The NFC_SOCKPROTO_RAW performs raw communication with NFC targets. + + + +--------------------------------------+ + | USER SPACE | + +--------------------------------------+ + ^ ^ + | low-level | control + | data exchange | operations + | | + | v + | +-----------+ + | AF_NFC | netlink | + | socket +-----------+ + | raw ^ + | | + v v + +---------+ +-----------+ + | rawsock | <--------> | core | + +---------+ +-----------+ + ^ + | + v + +-----------+ + | driver | + +-----------+ + +Device Driver Interface +----------------------- + +When registering on the NFC subsystem, the device driver must inform the core +of the set of supported NFC protocols and the set of ops callbacks. The ops +callbacks that must be implemented are the following: + +* start_poll - setup the device to poll for targets +* stop_poll - stop on progress polling operation +* activate_target - select and initialize one of the targets found +* deactivate_target - deselect and deinitialize the selected target +* data_exchange - send data and receive the response (transceive operation) + +Userspace interface +-------------------- + +The userspace interface is divided in control operations and low-level data +exchange operation. + +CONTROL OPERATIONS: + +Generic netlink is used to implement the interface to the control operations. +The operations are composed by commands and events, all listed below: + +* NFC_CMD_GET_DEVICE - get specific device info or dump the device list +* NFC_CMD_START_POLL - setup a specific device to polling for targets +* NFC_CMD_STOP_POLL - stop the polling operation in a specific device +* NFC_CMD_GET_TARGET - dump the list of targets found by a specific device + +* NFC_EVENT_DEVICE_ADDED - reports an NFC device addition +* NFC_EVENT_DEVICE_REMOVED - reports an NFC device removal +* NFC_EVENT_TARGETS_FOUND - reports START_POLL results when 1 or more targets +are found + +The user must call START_POLL to poll for NFC targets, passing the desired NFC +protocols through NFC_ATTR_PROTOCOLS attribute. The device remains in polling +state until it finds any target. However, the user can stop the polling +operation by calling STOP_POLL command. In this case, it will be checked if +the requester of STOP_POLL is the same of START_POLL. + +If the polling operation finds one or more targets, the event TARGETS_FOUND is +sent (including the device id). The user must call GET_TARGET to get the list of +all targets found by such device. Each reply message has target attributes with +relevant information such as the supported NFC protocols. + +All polling operations requested through one netlink socket are stopped when +it's closed. + +LOW-LEVEL DATA EXCHANGE: + +The userspace must use PF_NFC sockets to perform any data communication with +targets. All NFC sockets use AF_NFC: + +struct sockaddr_nfc { + sa_family_t sa_family; + __u32 dev_idx; + __u32 target_idx; + __u32 nfc_protocol; +}; + +To establish a connection with one target, the user must create an +NFC_SOCKPROTO_RAW socket and call the 'connect' syscall with the sockaddr_nfc +struct correctly filled. All information comes from NFC_EVENT_TARGETS_FOUND +netlink event. As a target can support more than one NFC protocol, the user +must inform which protocol it wants to use. + +Internally, 'connect' will result in an activate_target call to the driver. +When the socket is closed, the target is deactivated. + +The data format exchanged through the sockets is NFC protocol dependent. For +instance, when communicating with MIFARE tags, the data exchanged are MIFARE +commands and their responses. + +The first received package is the response to the first sent package and so +on. In order to allow valid "empty" responses, every data received has a NULL +header of 1 byte. diff --git a/Documentation/networking/stmmac.txt b/Documentation/networking/stmmac.txt index 80a7a345490..57a24108b84 100644 --- a/Documentation/networking/stmmac.txt +++ b/Documentation/networking/stmmac.txt @@ -7,7 +7,7 @@ This is the driver for the MAC 10/100/1000 on-chip Ethernet controllers (Synopsys IP blocks); it has been fully tested on STLinux platforms. Currently this network device driver is for all STM embedded MAC/GMAC -(7xxx SoCs). Other platforms start using it i.e. ARM SPEAr. +(i.e. 7xxx/5xxx SoCs) and it's known working on other platforms i.e. ARM SPEAr. DWC Ether MAC 10/100/1000 Universal version 3.41a and DWC Ether MAC 10/100 Universal version 4.0 have been used for developing the first code @@ -71,7 +71,7 @@ Several performance tests on STM platforms showed this optimisation allows to sp the CPU while having the maximum throughput. 4.4) WOL -Wake up on Lan feature through Magic Frame is only supported for the GMAC +Wake up on Lan feature through Magic and Unicast frames are supported for the GMAC core. 4.5) DMA descriptors @@ -91,11 +91,15 @@ LRO is not supported. The driver is compatible with PAL to work with PHY and GPHY devices. 4.9) Platform information -Several information came from the platform; please refer to the -driver's Header file in include/linux directory. +Several driver's information can be passed through the platform +These are included in the include/linux/stmmac.h header file +and detailed below as well: -struct plat_stmmacenet_data { + struct plat_stmmacenet_data { int bus_id; + int phy_addr; + int interface; + struct stmmac_mdio_bus_data *mdio_bus_data; int pbl; int clk_csr; int has_gmac; @@ -103,67 +107,135 @@ struct plat_stmmacenet_data { int tx_coe; int bugged_jumbo; int pmt; - void (*fix_mac_speed)(void *priv, unsigned int speed); - void (*bus_setup)(unsigned long ioaddr); -#ifdef CONFIG_STM_DRIVERS - struct stm_pad_config *pad_config; -#endif - void *bsp_priv; -}; + int force_sf_dma_mode; + void (*fix_mac_speed)(void *priv, unsigned int speed); + void (*bus_setup)(void __iomem *ioaddr); + int (*init)(struct platform_device *pdev); + void (*exit)(struct platform_device *pdev); + void *bsp_priv; + }; Where: -- pbl (Programmable Burst Length) is maximum number of - beats to be transferred in one DMA transaction. - GMAC also enables the 4xPBL by default. -- fix_mac_speed and bus_setup are used to configure internal target - registers (on STM platforms); -- has_gmac: GMAC core is on board (get it at run-time in the next step); -- bus_id: bus identifier. -- tx_coe: core is able to perform the tx csum in HW. -- enh_desc: if sets the MAC will use the enhanced descriptor structure. -- clk_csr: CSR Clock range selection. -- bugged_jumbo: some HWs are not able to perform the csum in HW for - over-sized frames due to limited buffer sizes. Setting this - flag the csum will be done in SW on JUMBO frames. - -struct plat_stmmacphy_data { - int bus_id; - int phy_addr; - unsigned int phy_mask; - int interface; - int (*phy_reset)(void *priv); - void *priv; -}; + o bus_id: bus identifier. + o phy_addr: the physical address can be passed from the platform. + If it is set to -1 the driver will automatically + detect it at run-time by probing all the 32 addresses. + o interface: PHY device's interface. + o mdio_bus_data: specific platform fields for the MDIO bus. + o pbl: the Programmable Burst Length is maximum number of beats to + be transferred in one DMA transaction. + GMAC also enables the 4xPBL by default. + o clk_csr: CSR Clock range selection. + o has_gmac: uses the GMAC core. + o enh_desc: if sets the MAC will use the enhanced descriptor structure. + o tx_coe: core is able to perform the tx csum in HW. + o bugged_jumbo: some HWs are not able to perform the csum in HW for + over-sized frames due to limited buffer sizes. + Setting this flag the csum will be done in SW on + JUMBO frames. + o pmt: core has the embedded power module (optional). + o force_sf_dma_mode: force DMA to use the Store and Forward mode + instead of the Threshold. + o fix_mac_speed: this callback is used for modifying some syscfg registers + (on ST SoCs) according to the link speed negotiated by the + physical layer . + o bus_setup: perform HW setup of the bus. For example, on some ST platforms + this field is used to configure the AMBA bridge to generate more + efficient STBus traffic. + o init/exit: callbacks used for calling a custom initialisation; + this is sometime necessary on some platforms (e.g. ST boxes) + where the HW needs to have set some PIO lines or system cfg + registers. + o custom_cfg: this is a custom configuration that can be passed while + initialising the resources. + +The we have: + + struct stmmac_mdio_bus_data { + int bus_id; + int (*phy_reset)(void *priv); + unsigned int phy_mask; + int *irqs; + int probed_phy_irq; + }; Where: -- bus_id: bus identifier; -- phy_addr: physical address used for the attached phy device; - set it to -1 to get it at run-time; -- interface: physical MII interface mode; -- phy_reset: hook to reset HW function. - -SOURCES: -- Kconfig -- Makefile -- stmmac_main.c: main network device driver; -- stmmac_mdio.c: mdio functions; -- stmmac_ethtool.c: ethtool support; -- stmmac_timer.[ch]: timer code used for mitigating the driver dma interrupts - Only tested on ST40 platforms based. -- stmmac.h: private driver structure; -- common.h: common definitions and VFTs; -- descs.h: descriptor structure definitions; -- dwmac1000_core.c: GMAC core functions; -- dwmac1000_dma.c: dma functions for the GMAC chip; -- dwmac1000.h: specific header file for the GMAC; -- dwmac100_core: MAC 100 core and dma code; -- dwmac100_dma.c: dma funtions for the MAC chip; -- dwmac1000.h: specific header file for the MAC; -- dwmac_lib.c: generic DMA functions shared among chips -- enh_desc.c: functions for handling enhanced descriptors -- norm_desc.c: functions for handling normal descriptors - -TODO: -- XGMAC controller is not supported. -- Review the timer optimisation code to use an embedded device that seems to be + o bus_id: bus identifier; + o phy_reset: hook to reset the phy device attached to the bus. + o phy_mask: phy mask passed when register the MDIO bus within the driver. + o irqs: list of IRQs, one per PHY. + o probed_phy_irq: if irqs is NULL, use this for probed PHY. + +Below an example how the structures above are using on ST platforms. + + static struct plat_stmmacenet_data stxYYY_ethernet_platform_data = { + .pbl = 32, + .has_gmac = 0, + .enh_desc = 0, + .fix_mac_speed = stxYYY_ethernet_fix_mac_speed, + | + |-> to write an internal syscfg + | on this platform when the + | link speed changes from 10 to + | 100 and viceversa + .init = &stmmac_claim_resource, + | + |-> On ST SoC this calls own "PAD" + | manager framework to claim + | all the resources necessary + | (GPIO ...). The .custom_cfg field + | is used to pass a custom config. +}; + +Below the usage of the stmmac_mdio_bus_data: on this SoC, in fact, +there are two MAC cores: one MAC is for MDIO Bus/PHY emulation +with fixed_link support. + +static struct stmmac_mdio_bus_data stmmac1_mdio_bus = { + .bus_id = 1, + | + |-> phy device on the bus_id 1 + .phy_reset = phy_reset; + | + |-> function to provide the phy_reset on this board + .phy_mask = 0, +}; + +static struct fixed_phy_status stmmac0_fixed_phy_status = { + .link = 1, + .speed = 100, + .duplex = 1, +}; + +During the board's device_init we can configure the first +MAC for fixed_link by calling: + fixed_phy_add(PHY_POLL, 1, &stmmac0_fixed_phy_status));) +and the second one, with a real PHY device attached to the bus, +by using the stmmac_mdio_bus_data structure (to provide the id, the +reset procedure etc). + +4.10) List of source files: + o Kconfig + o Makefile + o stmmac_main.c: main network device driver; + o stmmac_mdio.c: mdio functions; + o stmmac_ethtool.c: ethtool support; + o stmmac_timer.[ch]: timer code used for mitigating the driver dma interrupts + Only tested on ST40 platforms based. + o stmmac.h: private driver structure; + o common.h: common definitions and VFTs; + o descs.h: descriptor structure definitions; + o dwmac1000_core.c: GMAC core functions; + o dwmac1000_dma.c: dma functions for the GMAC chip; + o dwmac1000.h: specific header file for the GMAC; + o dwmac100_core: MAC 100 core and dma code; + o dwmac100_dma.c: dma funtions for the MAC chip; + o dwmac1000.h: specific header file for the MAC; + o dwmac_lib.c: generic DMA functions shared among chips + o enh_desc.c: functions for handling enhanced descriptors + o norm_desc.c: functions for handling normal descriptors + +5) TODO: + o XGMAC is not supported. + o Review the timer optimisation code to use an embedded device that will be available in new chip generations. |