diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/00-INDEX | 30 | ||||
| -rw-r--r-- | Documentation/networking/3c505.txt | 45 | ||||
| -rw-r--r-- | Documentation/networking/can.txt | 6 | ||||
| -rw-r--r-- | Documentation/networking/netlink_mmap.txt | 4 | ||||
| -rw-r--r-- | Documentation/networking/packet_mmap.txt | 2 | ||||
| -rw-r--r-- | Documentation/networking/timestamping.txt | 52 |
6 files changed, 60 insertions, 79 deletions
diff --git a/Documentation/networking/00-INDEX b/Documentation/networking/00-INDEX index f11580f8719..557b6ef70c2 100644 --- a/Documentation/networking/00-INDEX +++ b/Documentation/networking/00-INDEX @@ -6,8 +6,14 @@ - information on the 3Com Etherlink III Series Ethernet cards. 6pack.txt - info on the 6pack protocol, an alternative to KISS for AX.25 -DLINK.txt - - info on the D-Link DE-600/DE-620 parallel port pocket adapters +LICENSE.qla3xxx + - GPLv2 for QLogic Linux Networking HBA Driver +LICENSE.qlge + - GPLv2 for QLogic Linux qlge NIC Driver +LICENSE.qlcnic + - GPLv2 for QLogic Linux qlcnic NIC Driver +Makefile + - Makefile for docsrc. PLIP.txt - PLIP: The Parallel Line Internet Protocol device driver README.ipw2100 @@ -17,7 +23,7 @@ README.ipw2200 README.sb1000 - info on General Instrument/NextLevel SURFboard1000 cable modem. alias.txt - - info on using alias network devices + - info on using alias network devices. arcnet-hardware.txt - tons of info on ARCnet, hubs, jumper settings for ARCnet cards, etc. arcnet.txt @@ -80,7 +86,7 @@ framerelay.txt - info on using Frame Relay/Data Link Connection Identifier (DLCI). gen_stats.txt - Generic networking statistics for netlink users. -generic_hdlc.txt +generic-hdlc.txt - The generic High Level Data Link Control (HDLC) layer. generic_netlink.txt - info on Generic Netlink @@ -88,6 +94,8 @@ gianfar.txt - Gianfar Ethernet Driver. i40e.txt - README for the Intel Ethernet Controller XL710 Driver (i40e). +i40evf.txt + - Short note on the Driver for the Intel(R) XL710 X710 Virtual Function ieee802154.txt - Linux IEEE 802.15.4 implementation, API and drivers igb.txt @@ -102,6 +110,8 @@ ipddp.txt - AppleTalk-IP Decapsulation and AppleTalk-IP Encapsulation iphase.txt - Interphase PCI ATM (i)Chip IA Linux driver info. +ipsec.txt + - Note on not compressing IPSec payload and resulting failed policy check. ipv6.txt - Options to the ipv6 kernel module. ipvs-sysctl.txt @@ -120,6 +130,8 @@ lapb-module.txt - programming information of the LAPB module. ltpc.txt - the Apple or Farallon LocalTalk PC card driver +mac80211-auth-assoc-deauth.txt + - authentication and association / deauth-disassoc with max80211 mac80211-injection.txt - HOWTO use packet injection with mac80211 multiqueue.txt @@ -134,6 +146,10 @@ netdevices.txt - info on network device driver functions exported to the kernel. netif-msg.txt - Design of the network interface message level setting (NETIF_MSG_*). +netlink_mmap.txt + - memory mapped I/O with netlink +nf_conntrack-sysctl.txt + - list of netfilter-sysctl knobs. nfc.txt - The Linux Near Field Communication (NFS) subsystem. openvswitch.txt @@ -176,7 +192,7 @@ skfp.txt - SysKonnect FDDI (SK-5xxx, Compaq Netelligent) driver info. smc9.txt - the driver for SMC's 9000 series of Ethernet cards -spider-net.txt +spider_net.txt - README for the Spidernet Driver (as found in PS3 / Cell BE). stmmac.txt - README for the STMicro Synopsys Ethernet driver. @@ -188,6 +204,8 @@ tcp.txt - short blurb on how TCP output takes place. tcp-thin.txt - kernel tuning options for low rate 'thin' TCP streams. +team.txt + - pointer to information for ethernet teaming devices. tlan.txt - ThunderLAN (Compaq Netelligent 10/100, Olicom OC-2xxx) driver info. tproxy.txt @@ -200,6 +218,8 @@ vortex.txt - info on using 3Com Vortex (3c590, 3c592, 3c595, 3c597) Ethernet cards. vxge.txt - README for the Neterion X3100 PCIe Server Adapter. +vxlan.txt + - Virtual extensible LAN overview x25.txt - general info on X.25 development. x25-iface.txt diff --git a/Documentation/networking/3c505.txt b/Documentation/networking/3c505.txt deleted file mode 100644 index 72f38b13101..00000000000 --- a/Documentation/networking/3c505.txt +++ /dev/null @@ -1,45 +0,0 @@ -The 3Com Etherlink Plus (3c505) driver. - -This driver now uses DMA. There is currently no support for PIO operation. -The default DMA channel is 6; this is _not_ autoprobed, so you must -make sure you configure it correctly. If loading the driver as a -module, you can do this with "modprobe 3c505 dma=n". If the driver is -linked statically into the kernel, you must either use an "ether=" -statement on the command line, or change the definition of ELP_DMA in 3c505.h. - -The driver will warn you if it has to fall back on the compiled in -default DMA channel. - -If no base address is given at boot time, the driver will autoprobe -ports 0x300, 0x280 and 0x310 (in that order). If no IRQ is given, the driver -will try to probe for it. - -The driver can be used as a loadable module. - -Theoretically, one instance of the driver can now run multiple cards, -in the standard way (when loading a module, say "modprobe 3c505 -io=0x300,0x340 irq=10,11 dma=6,7" or whatever). I have not tested -this, though. - -The driver may now support revision 2 hardware; the dependency on -being able to read the host control register has been removed. This -is also untested, since I don't have a suitable card. - -Known problems: - I still see "DMA upload timed out" messages from time to time. These -seem to be fairly non-fatal though. - The card is old and slow. - -To do: - Improve probe/setup code - Test multicast and promiscuous operation - -Authors: - The driver is mainly written by Craig Southeren, email - <craigs@ineluki.apana.org.au>. - Parts of the driver (adapting the driver to 1.1.4+ kernels, - IRQ/address detection, some changes) and this README by - Juha Laiho <jlaiho@ichaos.nullnet.fi>. - DMA mode, more fixes, etc, by Philip Blundell <pjb27@cam.ac.uk> - Multicard support, Software configurable DMA, etc., by - Christopher Collins <ccollins@pcug.org.au> diff --git a/Documentation/networking/can.txt b/Documentation/networking/can.txt index f3089d42351..0cbe6ec22d6 100644 --- a/Documentation/networking/can.txt +++ b/Documentation/networking/can.txt @@ -554,12 +554,6 @@ solution for a couple of reasons: not specified in the struct can_frame and therefore it is only valid in CANFD_MTU sized CAN FD frames. - As long as the payload length is <=8 the received CAN frames from CAN FD - capable CAN devices can be received and read by legacy sockets too. When - user-generated CAN FD frames have a payload length <=8 these can be send - by legacy CAN network interfaces too. Sending CAN FD frames with payload - length > 8 to a legacy CAN network interface returns an -EMSGSIZE error. - Implementation hint for new CAN applications: To build a CAN FD aware application use struct canfd_frame as basic CAN diff --git a/Documentation/networking/netlink_mmap.txt b/Documentation/networking/netlink_mmap.txt index b2612297352..c6af4bac5aa 100644 --- a/Documentation/networking/netlink_mmap.txt +++ b/Documentation/networking/netlink_mmap.txt @@ -226,9 +226,9 @@ Ring setup: void *rx_ring, *tx_ring; /* Configure ring parameters */ - if (setsockopt(fd, NETLINK_RX_RING, &req, sizeof(req)) < 0) + if (setsockopt(fd, SOL_NETLINK, NETLINK_RX_RING, &req, sizeof(req)) < 0) exit(1); - if (setsockopt(fd, NETLINK_TX_RING, &req, sizeof(req)) < 0) + if (setsockopt(fd, SOL_NETLINK, NETLINK_TX_RING, &req, sizeof(req)) < 0) exit(1) /* Calculate size of each individual ring */ diff --git a/Documentation/networking/packet_mmap.txt b/Documentation/networking/packet_mmap.txt index 1404674c0a0..6fea79efb4c 100644 --- a/Documentation/networking/packet_mmap.txt +++ b/Documentation/networking/packet_mmap.txt @@ -453,7 +453,7 @@ TP_STATUS_COPY : This flag indicates that the frame (and associated enabled previously with setsockopt() and the PACKET_COPY_THRESH option. - The number of frames than can be buffered to + The number of frames that can be buffered to be read with recvfrom is limited like a normal socket. See the SO_RCVBUF option in the socket (7) man page. diff --git a/Documentation/networking/timestamping.txt b/Documentation/networking/timestamping.txt index 661d3c316a1..048c92b487f 100644 --- a/Documentation/networking/timestamping.txt +++ b/Documentation/networking/timestamping.txt @@ -21,26 +21,38 @@ has such a feature). SO_TIMESTAMPING: -Instructs the socket layer which kind of information is wanted. The -parameter is an integer with some of the following bits set. Setting -other bits is an error and doesn't change the current state. - -SOF_TIMESTAMPING_TX_HARDWARE: try to obtain send time stamp in hardware -SOF_TIMESTAMPING_TX_SOFTWARE: if SOF_TIMESTAMPING_TX_HARDWARE is off or - fails, then do it in software -SOF_TIMESTAMPING_RX_HARDWARE: return the original, unmodified time stamp - as generated by the hardware -SOF_TIMESTAMPING_RX_SOFTWARE: if SOF_TIMESTAMPING_RX_HARDWARE is off or - fails, then do it in software -SOF_TIMESTAMPING_RAW_HARDWARE: return original raw hardware time stamp -SOF_TIMESTAMPING_SYS_HARDWARE: return hardware time stamp transformed to - the system time base -SOF_TIMESTAMPING_SOFTWARE: return system time stamp generated in - software - -SOF_TIMESTAMPING_TX/RX determine how time stamps are generated. -SOF_TIMESTAMPING_RAW/SYS determine how they are reported in the -following control message: +Instructs the socket layer which kind of information should be collected +and/or reported. The parameter is an integer with some of the following +bits set. Setting other bits is an error and doesn't change the current +state. + +Four of the bits are requests to the stack to try to generate +timestamps. Any combination of them is valid. + +SOF_TIMESTAMPING_TX_HARDWARE: try to obtain send time stamps in hardware +SOF_TIMESTAMPING_TX_SOFTWARE: try to obtain send time stamps in software +SOF_TIMESTAMPING_RX_HARDWARE: try to obtain receive time stamps in hardware +SOF_TIMESTAMPING_RX_SOFTWARE: try to obtain receive time stamps in software + +The other three bits control which timestamps will be reported in a +generated control message. If none of these bits are set or if none of +the set bits correspond to data that is available, then the control +message will not be generated: + +SOF_TIMESTAMPING_SOFTWARE: report systime if available +SOF_TIMESTAMPING_SYS_HARDWARE: report hwtimetrans if available +SOF_TIMESTAMPING_RAW_HARDWARE: report hwtimeraw if available + +It is worth noting that timestamps may be collected for reasons other +than being requested by a particular socket with +SOF_TIMESTAMPING_[TR]X_(HARD|SOFT)WARE. For example, most drivers that +can generate hardware receive timestamps ignore +SOF_TIMESTAMPING_RX_HARDWARE. It is still a good idea to set that flag +in case future drivers pay attention. + +If timestamps are reported, they will appear in a control message with +cmsg_level==SOL_SOCKET, cmsg_type==SO_TIMESTAMPING, and a payload like +this: struct scm_timestamping { struct timespec systime; |