diff options
Diffstat (limited to 'Documentation/power/runtime_pm.txt')
| -rw-r--r-- | Documentation/power/runtime_pm.txt | 227 |
1 files changed, 220 insertions, 7 deletions
diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt index 55b859b3bc7..489e9bacd16 100644 --- a/Documentation/power/runtime_pm.txt +++ b/Documentation/power/runtime_pm.txt @@ -1,6 +1,7 @@ Run-time Power Management Framework for I/O Devices (C) 2009 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc. +(C) 2010 Alan Stern <stern@rowland.harvard.edu> 1. Introduction @@ -157,7 +158,8 @@ rules: to execute it, the other callbacks will not be executed for the same device. * A request to execute ->runtime_resume() will cancel any pending or - scheduled requests to execute the other callbacks for the same device. + scheduled requests to execute the other callbacks for the same device, + except for scheduled autosuspends. 3. Run-time PM Device Fields @@ -165,7 +167,7 @@ The following device run-time PM fields are present in 'struct dev_pm_info', as defined in include/linux/pm.h: struct timer_list suspend_timer; - - timer used for scheduling (delayed) suspend request + - timer used for scheduling (delayed) suspend and autosuspend requests unsigned long timer_expires; - timer expiration time, in jiffies (if this is different from zero, the @@ -230,6 +232,28 @@ defined in include/linux/pm.h: interface; it may only be modified with the help of the pm_runtime_allow() and pm_runtime_forbid() helper functions + unsigned int no_callbacks; + - indicates that the device does not use the run-time PM callbacks (see + Section 8); it may be modified only by the pm_runtime_no_callbacks() + helper function + + unsigned int use_autosuspend; + - indicates that the device's driver supports delayed autosuspend (see + Section 9); it may be modified only by the + pm_runtime{_dont}_use_autosuspend() helper functions + + unsigned int timer_autosuspends; + - indicates that the PM core should attempt to carry out an autosuspend + when the timer expires rather than a normal suspend + + int autosuspend_delay; + - the delay time (in milliseconds) to be used for autosuspend + + unsigned long last_busy; + - the time (in jiffies) when the pm_runtime_mark_last_busy() helper + function was last called for this device; used in calculating inactivity + periods for autosuspend + All of the above fields are members of the 'power' member of 'struct device'. 4. Run-time PM Device Helper Functions @@ -255,6 +279,12 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: error code on failure, where -EAGAIN or -EBUSY means it is safe to attempt to suspend the device again in future + int pm_runtime_autosuspend(struct device *dev); + - same as pm_runtime_suspend() except that the autosuspend delay is taken + into account; if pm_runtime_autosuspend_expiration() says the delay has + not yet expired then an autosuspend is scheduled for the appropriate time + and 0 is returned + int pm_runtime_resume(struct device *dev); - execute the subsystem-level resume callback for the device; returns 0 on success, 1 if the device's run-time PM status was already 'active' or @@ -267,6 +297,11 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: device (the request is represented by a work item in pm_wq); returns 0 on success or error code if the request has not been queued up + int pm_request_autosuspend(struct device *dev); + - schedule the execution of the subsystem-level suspend callback for the + device when the autosuspend delay has expired; if the delay has already + expired then the work item is queued up immediately + int pm_schedule_suspend(struct device *dev, unsigned int delay); - schedule the execution of the subsystem-level suspend callback for the device in future, where 'delay' is the time to wait before queuing up a @@ -298,12 +333,20 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: - decrement the device's usage counter int pm_runtime_put(struct device *dev); - - decrement the device's usage counter, run pm_request_idle(dev) and return - its result + - decrement the device's usage counter; if the result is 0 then run + pm_request_idle(dev) and return its result + + int pm_runtime_put_autosuspend(struct device *dev); + - decrement the device's usage counter; if the result is 0 then run + pm_request_autosuspend(dev) and return its result int pm_runtime_put_sync(struct device *dev); - - decrement the device's usage counter, run pm_runtime_idle(dev) and return - its result + - decrement the device's usage counter; if the result is 0 then run + pm_runtime_idle(dev) and return its result + + int pm_runtime_put_sync_autosuspend(struct device *dev); + - decrement the device's usage counter; if the result is 0 then run + pm_runtime_autosuspend(dev) and return its result void pm_runtime_enable(struct device *dev); - enable the run-time PM helper functions to run the device bus type's @@ -349,19 +392,51 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: counter (used by the /sys/devices/.../power/control interface to effectively prevent the device from being power managed at run time) + void pm_runtime_no_callbacks(struct device *dev); + - set the power.no_callbacks flag for the device and remove the run-time + PM attributes from /sys/devices/.../power (or prevent them from being + added when the device is registered) + + void pm_runtime_mark_last_busy(struct device *dev); + - set the power.last_busy field to the current time + + void pm_runtime_use_autosuspend(struct device *dev); + - set the power.use_autosuspend flag, enabling autosuspend delays + + void pm_runtime_dont_use_autosuspend(struct device *dev); + - clear the power.use_autosuspend flag, disabling autosuspend delays + + void pm_runtime_set_autosuspend_delay(struct device *dev, int delay); + - set the power.autosuspend_delay value to 'delay' (expressed in + milliseconds); if 'delay' is negative then run-time suspends are + prevented + + unsigned long pm_runtime_autosuspend_expiration(struct device *dev); + - calculate the time when the current autosuspend delay period will expire, + based on power.last_busy and power.autosuspend_delay; if the delay time + is 1000 ms or larger then the expiration time is rounded up to the + nearest second; returns 0 if the delay period has already expired or + power.use_autosuspend isn't set, otherwise returns the expiration time + in jiffies + It is safe to execute the following helper functions from interrupt context: pm_request_idle() +pm_request_autosuspend() pm_schedule_suspend() pm_request_resume() pm_runtime_get_noresume() pm_runtime_get() pm_runtime_put_noidle() pm_runtime_put() +pm_runtime_put_autosuspend() +pm_runtime_enable() pm_suspend_ignore_children() pm_runtime_set_active() pm_runtime_set_suspended() -pm_runtime_enable() +pm_runtime_suspended() +pm_runtime_mark_last_busy() +pm_runtime_autosuspend_expiration() 5. Run-time PM Initialization, Device Probing and Removal @@ -524,3 +599,141 @@ poweroff and run-time suspend callback, and similarly for system resume, thaw, restore, and run-time resume, can achieve this with the help of the UNIVERSAL_DEV_PM_OPS macro defined in include/linux/pm.h (possibly setting its last argument to NULL). + +8. "No-Callback" Devices + +Some "devices" are only logical sub-devices of their parent and cannot be +power-managed on their own. (The prototype example is a USB interface. Entire +USB devices can go into low-power mode or send wake-up requests, but neither is +possible for individual interfaces.) The drivers for these devices have no +need of run-time PM callbacks; if the callbacks did exist, ->runtime_suspend() +and ->runtime_resume() would always return 0 without doing anything else and +->runtime_idle() would always call pm_runtime_suspend(). + +Subsystems can tell the PM core about these devices by calling +pm_runtime_no_callbacks(). This should be done after the device structure is +initialized and before it is registered (although after device registration is +also okay). The routine will set the device's power.no_callbacks flag and +prevent the non-debugging run-time PM sysfs attributes from being created. + +When power.no_callbacks is set, the PM core will not invoke the +->runtime_idle(), ->runtime_suspend(), or ->runtime_resume() callbacks. +Instead it will assume that suspends and resumes always succeed and that idle +devices should be suspended. + +As a consequence, the PM core will never directly inform the device's subsystem +or driver about run-time power changes. Instead, the driver for the device's +parent must take responsibility for telling the device's driver when the +parent's power state changes. + +9. Autosuspend, or automatically-delayed suspends + +Changing a device's power state isn't free; it requires both time and energy. +A device should be put in a low-power state only when there's some reason to +think it will remain in that state for a substantial time. A common heuristic +says that a device which hasn't been used for a while is liable to remain +unused; following this advice, drivers should not allow devices to be suspended +at run-time until they have been inactive for some minimum period. Even when +the heuristic ends up being non-optimal, it will still prevent devices from +"bouncing" too rapidly between low-power and full-power states. + +The term "autosuspend" is an historical remnant. It doesn't mean that the +device is automatically suspended (the subsystem or driver still has to call +the appropriate PM routines); rather it means that run-time suspends will +automatically be delayed until the desired period of inactivity has elapsed. + +Inactivity is determined based on the power.last_busy field. Drivers should +call pm_runtime_mark_last_busy() to update this field after carrying out I/O, +typically just before calling pm_runtime_put_autosuspend(). The desired length +of the inactivity period is a matter of policy. Subsystems can set this length +initially by calling pm_runtime_set_autosuspend_delay(), but after device +registration the length should be controlled by user space, using the +/sys/devices/.../power/autosuspend_delay_ms attribute. + +In order to use autosuspend, subsystems or drivers must call +pm_runtime_use_autosuspend() (preferably before registering the device), and +thereafter they should use the various *_autosuspend() helper functions instead +of the non-autosuspend counterparts: + + Instead of: pm_runtime_suspend use: pm_runtime_autosuspend; + Instead of: pm_schedule_suspend use: pm_request_autosuspend; + Instead of: pm_runtime_put use: pm_runtime_put_autosuspend; + Instead of: pm_runtime_put_sync use: pm_runtime_put_sync_autosuspend. + +Drivers may also continue to use the non-autosuspend helper functions; they +will behave normally, not taking the autosuspend delay into account. +Similarly, if the power.use_autosuspend field isn't set then the autosuspend +helper functions will behave just like the non-autosuspend counterparts. + +The implementation is well suited for asynchronous use in interrupt contexts. +However such use inevitably involves races, because the PM core can't +synchronize ->runtime_suspend() callbacks with the arrival of I/O requests. +This synchronization must be handled by the driver, using its private lock. +Here is a schematic pseudo-code example: + + foo_read_or_write(struct foo_priv *foo, void *data) + { + lock(&foo->private_lock); + add_request_to_io_queue(foo, data); + if (foo->num_pending_requests++ == 0) + pm_runtime_get(&foo->dev); + if (!foo->is_suspended) + foo_process_next_request(foo); + unlock(&foo->private_lock); + } + + foo_io_completion(struct foo_priv *foo, void *req) + { + lock(&foo->private_lock); + if (--foo->num_pending_requests == 0) { + pm_runtime_mark_last_busy(&foo->dev); + pm_runtime_put_autosuspend(&foo->dev); + } else { + foo_process_next_request(foo); + } + unlock(&foo->private_lock); + /* Send req result back to the user ... */ + } + + int foo_runtime_suspend(struct device *dev) + { + struct foo_priv foo = container_of(dev, ...); + int ret = 0; + + lock(&foo->private_lock); + if (foo->num_pending_requests > 0) { + ret = -EBUSY; + } else { + /* ... suspend the device ... */ + foo->is_suspended = 1; + } + unlock(&foo->private_lock); + return ret; + } + + int foo_runtime_resume(struct device *dev) + { + struct foo_priv foo = container_of(dev, ...); + + lock(&foo->private_lock); + /* ... resume the device ... */ + foo->is_suspended = 0; + pm_runtime_mark_last_busy(&foo->dev); + if (foo->num_pending_requests > 0) + foo_process_requests(foo); + unlock(&foo->private_lock); + return 0; + } + +The important point is that after foo_io_completion() asks for an autosuspend, +the foo_runtime_suspend() callback may race with foo_read_or_write(). +Therefore foo_runtime_suspend() has to check whether there are any pending I/O +requests (while holding the private lock) before allowing the suspend to +proceed. + +In addition, the power.autosuspend_delay field can be changed by user space at +any time. If a driver cares about this, it can call +pm_runtime_autosuspend_expiration() from within the ->runtime_suspend() +callback while holding its private lock. If the function returns a nonzero +value then the delay has not yet expired and the callback should return +-EAGAIN. |