summaryrefslogtreecommitdiffstats
path: root/Documentation/power/userland-swsusp.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/power/userland-swsusp.txt')
-rw-r--r--Documentation/power/userland-swsusp.txt64
1 files changed, 51 insertions, 13 deletions
diff --git a/Documentation/power/userland-swsusp.txt b/Documentation/power/userland-swsusp.txt
index 64755e9285d..000556c932e 100644
--- a/Documentation/power/userland-swsusp.txt
+++ b/Documentation/power/userland-swsusp.txt
@@ -9,9 +9,8 @@ done it already.
Now, to use the userland interface for software suspend you need special
utilities that will read/write the system memory snapshot from/to the
kernel. Such utilities are available, for example, from
-<http://www.sisk.pl/kernel/utilities/suspend>. You may want to have
-a look at them if you are going to develop your own suspend/resume
-utilities.
+<http://suspend.sourceforge.net>. You may want to have a look at them if you
+are going to develop your own suspend/resume utilities.
The interface consists of a character device providing the open(),
release(), read(), and write() operations as well as several ioctl()
@@ -21,9 +20,9 @@ be read from /sys/class/misc/snapshot/dev.
The device can be open either for reading or for writing. If open for
reading, it is considered to be in the suspend mode. Otherwise it is
-assumed to be in the resume mode. The device cannot be open for reading
-and writing. It is also impossible to have the device open more than once
-at a time.
+assumed to be in the resume mode. The device cannot be open for simultaneous
+reading and writing. It is also impossible to have the device open more than
+once at a time.
The ioctl() commands recognized by the device are:
@@ -69,9 +68,46 @@ SNAPSHOT_FREE_SWAP_PAGES - free all swap pages allocated with
SNAPSHOT_SET_SWAP_FILE - set the resume partition (the last ioctl() argument
should specify the device's major and minor numbers in the old
two-byte format, as returned by the stat() function in the .st_rdev
- member of the stat structure); it is recommended to always use this
- call, because the code to set the resume partition could be removed from
- future kernels
+ member of the stat structure)
+
+SNAPSHOT_SET_SWAP_AREA - set the resume partition and the offset (in <PAGE_SIZE>
+ units) from the beginning of the partition at which the swap header is
+ located (the last ioctl() argument should point to a struct
+ resume_swap_area, as defined in kernel/power/power.h, containing the
+ resume device specification, as for the SNAPSHOT_SET_SWAP_FILE ioctl(),
+ and the offset); for swap partitions the offset is always 0, but it is
+ different to zero for swap files (please see
+ Documentation/swsusp-and-swap-files.txt for details).
+ The SNAPSHOT_SET_SWAP_AREA ioctl() is considered as a replacement for
+ SNAPSHOT_SET_SWAP_FILE which is regarded as obsolete. It is
+ recommended to always use this call, because the code to set the resume
+ partition may be removed from future kernels
+
+SNAPSHOT_S2RAM - suspend to RAM; using this call causes the kernel to
+ immediately enter the suspend-to-RAM state, so this call must always
+ be preceded by the SNAPSHOT_FREEZE call and it is also necessary
+ to use the SNAPSHOT_UNFREEZE call after the system wakes up. This call
+ is needed to implement the suspend-to-both mechanism in which the
+ suspend image is first created, as though the system had been suspended
+ to disk, and then the system is suspended to RAM (this makes it possible
+ to resume the system from RAM if there's enough battery power or restore
+ its state on the basis of the saved suspend image otherwise)
+
+SNAPSHOT_PMOPS - enable the usage of the pmops->prepare, pmops->enter and
+ pmops->finish methods (the in-kernel swsusp knows these as the "platform
+ method") which are needed on many machines to (among others) speed up
+ the resume by letting the BIOS skip some steps or to let the system
+ recognise the correct state of the hardware after the resume (in
+ particular on many machines this ensures that unplugged AC
+ adapters get correctly detected and that kacpid does not run wild after
+ the resume). The last ioctl() argument can take one of the three
+ values, defined in kernel/power/power.h:
+ PMOPS_PREPARE - make the kernel carry out the
+ pm_ops->prepare(PM_SUSPEND_DISK) operation
+ PMOPS_ENTER - make the kernel power off the system by calling
+ pm_ops->enter(PM_SUSPEND_DISK)
+ PMOPS_FINISH - make the kernel carry out the
+ pm_ops->finish(PM_SUSPEND_DISK) operation
The device's read() operation can be used to transfer the snapshot image from
the kernel. It has the following limitations:
@@ -91,10 +127,12 @@ unfreeze user space processes frozen by SNAPSHOT_UNFREEZE if they are
still frozen when the device is being closed).
Currently it is assumed that the userland utilities reading/writing the
-snapshot image from/to the kernel will use a swap partition, called the resume
-partition, as storage space. However, this is not really required, as they
-can use, for example, a special (blank) suspend partition or a file on a partition
-that is unmounted before SNAPSHOT_ATOMIC_SNAPSHOT and mounted afterwards.
+snapshot image from/to the kernel will use a swap parition, called the resume
+partition, or a swap file as storage space (if a swap file is used, the resume
+partition is the partition that holds this file). However, this is not really
+required, as they can use, for example, a special (blank) suspend partition or
+a file on a partition that is unmounted before SNAPSHOT_ATOMIC_SNAPSHOT and
+mounted afterwards.
These utilities SHOULD NOT make any assumptions regarding the ordering of
data within the snapshot image, except for the image header that MAY be