diff options
Diffstat (limited to 'Documentation/powerpc/dts-bindings/4xx/emac.txt')
| -rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/emac.txt | 148 |
1 files changed, 0 insertions, 148 deletions
diff --git a/Documentation/powerpc/dts-bindings/4xx/emac.txt b/Documentation/powerpc/dts-bindings/4xx/emac.txt deleted file mode 100644 index 2161334a7ca..00000000000 --- a/Documentation/powerpc/dts-bindings/4xx/emac.txt +++ /dev/null @@ -1,148 +0,0 @@ - 4xx/Axon EMAC ethernet nodes - - The EMAC ethernet controller in IBM and AMCC 4xx chips, and also - the Axon bridge. To operate this needs to interact with a ths - special McMAL DMA controller, and sometimes an RGMII or ZMII - interface. In addition to the nodes and properties described - below, the node for the OPB bus on which the EMAC sits must have a - correct clock-frequency property. - - i) The EMAC node itself - - Required properties: - - device_type : "network" - - - compatible : compatible list, contains 2 entries, first is - "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, - 405gp, Axon) and second is either "ibm,emac" or - "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", - "ibm,emac4" - - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> - - interrupt-parent : optional, if needed for interrupt mapping - - reg : <registers mapping> - - local-mac-address : 6 bytes, MAC address - - mal-device : phandle of the associated McMAL node - - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated - with this EMAC - - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated - with this EMAC - - cell-index : 1 cell, hardware index of the EMAC cell on a given - ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on - each Axon chip) - - max-frame-size : 1 cell, maximum frame size supported in bytes - - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048 - - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048. - - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate - thresholds). - For Axon, 0x00000010 - - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) - in bytes. - For Axon, 0x00000100 (I think ...) - - phy-mode : string, mode of operations of the PHY interface. - Supported values are: "mii", "rmii", "smii", "rgmii", - "tbi", "gmii", rtbi", "sgmii". - For Axon on CAB, it is "rgmii" - - mdio-device : 1 cell, required iff using shared MDIO registers - (440EP). phandle of the EMAC to use to drive the - MDIO lines for the PHY used by this EMAC. - - zmii-device : 1 cell, required iff connected to a ZMII. phandle of - the ZMII device node - - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII - channel or 0xffffffff if ZMII is only used for MDIO. - - rgmii-device : 1 cell, required iff connected to an RGMII. phandle - of the RGMII device node. - For Axon: phandle of plb5/plb4/opb/rgmii - - rgmii-channel : 1 cell, required iff connected to an RGMII. Which - RGMII channel is used by this EMAC. - Fox Axon: present, whatever value is appropriate for each - EMAC, that is the content of the current (bogus) "phy-port" - property. - - Optional properties: - - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, - a search is performed. - - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY - for, used if phy-address is absent. bit 0x00000001 is - MDIO address 0. - For Axon it can be absent, though my current driver - doesn't handle phy-address yet so for now, keep - 0x00ffffff in it. - - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - rx-fifo-size). For Axon, either absent or 2048. - - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - tx-fifo-size). For Axon, either absent or 2048. - - tah-device : 1 cell, optional. If connected to a TAH engine for - offload, phandle of the TAH device node. - - tah-channel : 1 cell, optional. If appropriate, channel used on the - TAH engine. - - Example: - - EMAC0: ethernet@40000800 { - device_type = "network"; - compatible = "ibm,emac-440gp", "ibm,emac"; - interrupt-parent = <&UIC1>; - interrupts = <1c 4 1d 4>; - reg = <40000800 70>; - local-mac-address = [00 04 AC E3 1B 1E]; - mal-device = <&MAL0>; - mal-tx-channel = <0 1>; - mal-rx-channel = <0>; - cell-index = <0>; - max-frame-size = <5dc>; - rx-fifo-size = <1000>; - tx-fifo-size = <800>; - phy-mode = "rmii"; - phy-map = <00000001>; - zmii-device = <&ZMII0>; - zmii-channel = <0>; - }; - - ii) McMAL node - - Required properties: - - device_type : "dma-controller" - - compatible : compatible list, containing 2 entries, first is - "ibm,mcmal-CHIP" where CHIP is the host ASIC (like - emac) and the second is either "ibm,mcmal" or - "ibm,mcmal2". - For Axon, "ibm,mcmal-axon","ibm,mcmal2" - - interrupts : <interrupt mapping for the MAL interrupts sources: - 5 sources: tx_eob, rx_eob, serr, txde, rxde>. - For Axon: This is _different_ from the current - firmware. We use the "delayed" interrupts for txeob - and rxeob. Thus we end up with mapping those 5 MPIC - interrupts, all level positive sensitive: 10, 11, 32, - 33, 34 (in decimal) - - dcr-reg : < DCR registers range > - - dcr-parent : if needed for dcr-reg - - num-tx-chans : 1 cell, number of Tx channels - - num-rx-chans : 1 cell, number of Rx channels - - iii) ZMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,zmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,zmii". - For Axon, there is no ZMII node. - - reg : <registers mapping> - - iv) RGMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,rgmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,rgmii". - For Axon, "ibm,rgmii-axon","ibm,rgmii" - - reg : <registers mapping> - - revision : as provided by the RGMII new version register if - available. - For Axon: 0x0000012a - |