diff options
Diffstat (limited to 'Documentation/powerpc/dts-bindings/4xx/emac.txt')
| -rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/emac.txt | 148 |
1 files changed, 148 insertions, 0 deletions
diff --git a/Documentation/powerpc/dts-bindings/4xx/emac.txt b/Documentation/powerpc/dts-bindings/4xx/emac.txt new file mode 100644 index 00000000000..2161334a7ca --- /dev/null +++ b/Documentation/powerpc/dts-bindings/4xx/emac.txt @@ -0,0 +1,148 @@ + 4xx/Axon EMAC ethernet nodes + + The EMAC ethernet controller in IBM and AMCC 4xx chips, and also + the Axon bridge. To operate this needs to interact with a ths + special McMAL DMA controller, and sometimes an RGMII or ZMII + interface. In addition to the nodes and properties described + below, the node for the OPB bus on which the EMAC sits must have a + correct clock-frequency property. + + i) The EMAC node itself + + Required properties: + - device_type : "network" + + - compatible : compatible list, contains 2 entries, first is + "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, + 405gp, Axon) and second is either "ibm,emac" or + "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", + "ibm,emac4" + - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> + - interrupt-parent : optional, if needed for interrupt mapping + - reg : <registers mapping> + - local-mac-address : 6 bytes, MAC address + - mal-device : phandle of the associated McMAL node + - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated + with this EMAC + - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated + with this EMAC + - cell-index : 1 cell, hardware index of the EMAC cell on a given + ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on + each Axon chip) + - max-frame-size : 1 cell, maximum frame size supported in bytes + - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048 + - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048. + - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate + thresholds). + For Axon, 0x00000010 + - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) + in bytes. + For Axon, 0x00000100 (I think ...) + - phy-mode : string, mode of operations of the PHY interface. + Supported values are: "mii", "rmii", "smii", "rgmii", + "tbi", "gmii", rtbi", "sgmii". + For Axon on CAB, it is "rgmii" + - mdio-device : 1 cell, required iff using shared MDIO registers + (440EP). phandle of the EMAC to use to drive the + MDIO lines for the PHY used by this EMAC. + - zmii-device : 1 cell, required iff connected to a ZMII. phandle of + the ZMII device node + - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII + channel or 0xffffffff if ZMII is only used for MDIO. + - rgmii-device : 1 cell, required iff connected to an RGMII. phandle + of the RGMII device node. + For Axon: phandle of plb5/plb4/opb/rgmii + - rgmii-channel : 1 cell, required iff connected to an RGMII. Which + RGMII channel is used by this EMAC. + Fox Axon: present, whatever value is appropriate for each + EMAC, that is the content of the current (bogus) "phy-port" + property. + + Optional properties: + - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, + a search is performed. + - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY + for, used if phy-address is absent. bit 0x00000001 is + MDIO address 0. + For Axon it can be absent, though my current driver + doesn't handle phy-address yet so for now, keep + 0x00ffffff in it. + - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + rx-fifo-size). For Axon, either absent or 2048. + - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + tx-fifo-size). For Axon, either absent or 2048. + - tah-device : 1 cell, optional. If connected to a TAH engine for + offload, phandle of the TAH device node. + - tah-channel : 1 cell, optional. If appropriate, channel used on the + TAH engine. + + Example: + + EMAC0: ethernet@40000800 { + device_type = "network"; + compatible = "ibm,emac-440gp", "ibm,emac"; + interrupt-parent = <&UIC1>; + interrupts = <1c 4 1d 4>; + reg = <40000800 70>; + local-mac-address = [00 04 AC E3 1B 1E]; + mal-device = <&MAL0>; + mal-tx-channel = <0 1>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + zmii-device = <&ZMII0>; + zmii-channel = <0>; + }; + + ii) McMAL node + + Required properties: + - device_type : "dma-controller" + - compatible : compatible list, containing 2 entries, first is + "ibm,mcmal-CHIP" where CHIP is the host ASIC (like + emac) and the second is either "ibm,mcmal" or + "ibm,mcmal2". + For Axon, "ibm,mcmal-axon","ibm,mcmal2" + - interrupts : <interrupt mapping for the MAL interrupts sources: + 5 sources: tx_eob, rx_eob, serr, txde, rxde>. + For Axon: This is _different_ from the current + firmware. We use the "delayed" interrupts for txeob + and rxeob. Thus we end up with mapping those 5 MPIC + interrupts, all level positive sensitive: 10, 11, 32, + 33, 34 (in decimal) + - dcr-reg : < DCR registers range > + - dcr-parent : if needed for dcr-reg + - num-tx-chans : 1 cell, number of Tx channels + - num-rx-chans : 1 cell, number of Rx channels + + iii) ZMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,zmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,zmii". + For Axon, there is no ZMII node. + - reg : <registers mapping> + + iv) RGMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,rgmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,rgmii". + For Axon, "ibm,rgmii-axon","ibm,rgmii" + - reg : <registers mapping> + - revision : as provided by the RGMII new version register if + available. + For Axon: 0x0000012a + |