diff options
Diffstat (limited to 'Documentation/powerpc')
60 files changed, 0 insertions, 5554 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt deleted file mode 100644 index 7400d7555dc..00000000000 --- a/Documentation/powerpc/booting-without-of.txt +++ /dev/null @@ -1,1447 +0,0 @@ - Booting the Linux/ppc kernel without Open Firmware - -------------------------------------------------- - -(c) 2005 Benjamin Herrenschmidt <benh at kernel.crashing.org>, - IBM Corp. -(c) 2005 Becky Bruce <becky.bruce at freescale.com>, - Freescale Semiconductor, FSL SOC and 32-bit additions -(c) 2006 MontaVista Software, Inc. - Flash chip node definition - -Table of Contents -================= - - I - Introduction - 1) Entry point for arch/powerpc - 2) Board support - - II - The DT block format - 1) Header - 2) Device tree generalities - 3) Device tree "structure" block - 4) Device tree "strings" block - - III - Required content of the device tree - 1) Note about cells and address representation - 2) Note about "compatible" properties - 3) Note about "name" properties - 4) Note about node and property names and character set - 5) Required nodes and properties - a) The root node - b) The /cpus node - c) The /cpus/* nodes - d) the /memory node(s) - e) The /chosen node - f) the /soc<SOCname> node - - IV - "dtc", the device tree compiler - - V - Recommendations for a bootloader - - VI - System-on-a-chip devices and nodes - 1) Defining child nodes of an SOC - 2) Representing devices without a current OF specification - a) PHY nodes - b) Interrupt controllers - c) 4xx/Axon EMAC ethernet nodes - d) Xilinx IP cores - e) USB EHCI controllers - f) MDIO on GPIOs - g) SPI busses - - VII - Specifying interrupt information for devices - 1) interrupts property - 2) interrupt-parent property - 3) OpenPIC Interrupt Controllers - 4) ISA Interrupt Controllers - - VIII - Specifying device power management information (sleep property) - - Appendix A - Sample SOC node for MPC8540 - - -Revision Information -==================== - - May 18, 2005: Rev 0.1 - Initial draft, no chapter III yet. - - May 19, 2005: Rev 0.2 - Add chapter III and bits & pieces here or - clarifies the fact that a lot of things are - optional, the kernel only requires a very - small device tree, though it is encouraged - to provide an as complete one as possible. - - May 24, 2005: Rev 0.3 - Precise that DT block has to be in RAM - - Misc fixes - - Define version 3 and new format version 16 - for the DT block (version 16 needs kernel - patches, will be fwd separately). - String block now has a size, and full path - is replaced by unit name for more - compactness. - linux,phandle is made optional, only nodes - that are referenced by other nodes need it. - "name" property is now automatically - deduced from the unit name - - June 1, 2005: Rev 0.4 - Correct confusion between OF_DT_END and - OF_DT_END_NODE in structure definition. - - Change version 16 format to always align - property data to 4 bytes. Since tokens are - already aligned, that means no specific - required alignment between property size - and property data. The old style variable - alignment would make it impossible to do - "simple" insertion of properties using - memmove (thanks Milton for - noticing). Updated kernel patch as well - - Correct a few more alignment constraints - - Add a chapter about the device-tree - compiler and the textural representation of - the tree that can be "compiled" by dtc. - - November 21, 2005: Rev 0.5 - - Additions/generalizations for 32-bit - - Changed to reflect the new arch/powerpc - structure - - Added chapter VI - - - ToDo: - - Add some definitions of interrupt tree (simple/complex) - - Add some definitions for PCI host bridges - - Add some common address format examples - - Add definitions for standard properties and "compatible" - names for cells that are not already defined by the existing - OF spec. - - Compare FSL SOC use of PCI to standard and make sure no new - node definition required. - - Add more information about node definitions for SOC devices - that currently have no standard, like the FSL CPM. - - -I - Introduction -================ - -During the recent development of the Linux/ppc64 kernel, and more -specifically, the addition of new platform types outside of the old -IBM pSeries/iSeries pair, it was decided to enforce some strict rules -regarding the kernel entry and bootloader <-> kernel interfaces, in -order to avoid the degeneration that had become the ppc32 kernel entry -point and the way a new platform should be added to the kernel. The -legacy iSeries platform breaks those rules as it predates this scheme, -but no new board support will be accepted in the main tree that -doesn't follow them properly. In addition, since the advent of the -arch/powerpc merged architecture for ppc32 and ppc64, new 32-bit -platforms and 32-bit platforms which move into arch/powerpc will be -required to use these rules as well. - -The main requirement that will be defined in more detail below is -the presence of a device-tree whose format is defined after Open -Firmware specification. However, in order to make life easier -to embedded board vendors, the kernel doesn't require the device-tree -to represent every device in the system and only requires some nodes -and properties to be present. This will be described in detail in -section III, but, for example, the kernel does not require you to -create a node for every PCI device in the system. It is a requirement -to have a node for PCI host bridges in order to provide interrupt -routing informations and memory/IO ranges, among others. It is also -recommended to define nodes for on chip devices and other busses that -don't specifically fit in an existing OF specification. This creates a -great flexibility in the way the kernel can then probe those and match -drivers to device, without having to hard code all sorts of tables. It -also makes it more flexible for board vendors to do minor hardware -upgrades without significantly impacting the kernel code or cluttering -it with special cases. - - -1) Entry point for arch/powerpc -------------------------------- - - There is one and one single entry point to the kernel, at the start - of the kernel image. That entry point supports two calling - conventions: - - a) Boot from Open Firmware. If your firmware is compatible - with Open Firmware (IEEE 1275) or provides an OF compatible - client interface API (support for "interpret" callback of - forth words isn't required), you can enter the kernel with: - - r5 : OF callback pointer as defined by IEEE 1275 - bindings to powerpc. Only the 32-bit client interface - is currently supported - - r3, r4 : address & length of an initrd if any or 0 - - The MMU is either on or off; the kernel will run the - trampoline located in arch/powerpc/kernel/prom_init.c to - extract the device-tree and other information from open - firmware and build a flattened device-tree as described - in b). prom_init() will then re-enter the kernel using - the second method. This trampoline code runs in the - context of the firmware, which is supposed to handle all - exceptions during that time. - - b) Direct entry with a flattened device-tree block. This entry - point is called by a) after the OF trampoline and can also be - called directly by a bootloader that does not support the Open - Firmware client interface. It is also used by "kexec" to - implement "hot" booting of a new kernel from a previous - running one. This method is what I will describe in more - details in this document, as method a) is simply standard Open - Firmware, and thus should be implemented according to the - various standard documents defining it and its binding to the - PowerPC platform. The entry point definition then becomes: - - r3 : physical pointer to the device-tree block - (defined in chapter II) in RAM - - r4 : physical pointer to the kernel itself. This is - used by the assembly code to properly disable the MMU - in case you are entering the kernel with MMU enabled - and a non-1:1 mapping. - - r5 : NULL (as to differentiate with method a) - - Note about SMP entry: Either your firmware puts your other - CPUs in some sleep loop or spin loop in ROM where you can get - them out via a soft reset or some other means, in which case - you don't need to care, or you'll have to enter the kernel - with all CPUs. The way to do that with method b) will be - described in a later revision of this document. - - -2) Board support ----------------- - -64-bit kernels: - - Board supports (platforms) are not exclusive config options. An - arbitrary set of board supports can be built in a single kernel - image. The kernel will "know" what set of functions to use for a - given platform based on the content of the device-tree. Thus, you - should: - - a) add your platform support as a _boolean_ option in - arch/powerpc/Kconfig, following the example of PPC_PSERIES, - PPC_PMAC and PPC_MAPLE. The later is probably a good - example of a board support to start from. - - b) create your main platform file as - "arch/powerpc/platforms/myplatform/myboard_setup.c" and add it - to the Makefile under the condition of your CONFIG_ - option. This file will define a structure of type "ppc_md" - containing the various callbacks that the generic code will - use to get to your platform specific code - - c) Add a reference to your "ppc_md" structure in the - "machines" table in arch/powerpc/kernel/setup_64.c if you are - a 64-bit platform. - - d) request and get assigned a platform number (see PLATFORM_* - constants in arch/powerpc/include/asm/processor.h - -32-bit embedded kernels: - - Currently, board support is essentially an exclusive config option. - The kernel is configured for a single platform. Part of the reason - for this is to keep kernels on embedded systems small and efficient; - part of this is due to the fact the code is already that way. In the - future, a kernel may support multiple platforms, but only if the - platforms feature the same core architecture. A single kernel build - cannot support both configurations with Book E and configurations - with classic Powerpc architectures. - - 32-bit embedded platforms that are moved into arch/powerpc using a - flattened device tree should adopt the merged tree practice of - setting ppc_md up dynamically, even though the kernel is currently - built with support for only a single platform at a time. This allows - unification of the setup code, and will make it easier to go to a - multiple-platform-support model in the future. - -NOTE: I believe the above will be true once Ben's done with the merge -of the boot sequences.... someone speak up if this is wrong! - - To add a 32-bit embedded platform support, follow the instructions - for 64-bit platforms above, with the exception that the Kconfig - option should be set up such that the kernel builds exclusively for - the platform selected. The processor type for the platform should - enable another config option to select the specific board - supported. - -NOTE: If Ben doesn't merge the setup files, may need to change this to -point to setup_32.c - - - I will describe later the boot process and various callbacks that - your platform should implement. - - -II - The DT block format -======================== - - -This chapter defines the actual format of the flattened device-tree -passed to the kernel. The actual content of it and kernel requirements -are described later. You can find example of code manipulating that -format in various places, including arch/powerpc/kernel/prom_init.c -which will generate a flattened device-tree from the Open Firmware -representation, or the fs2dt utility which is part of the kexec tools -which will generate one from a filesystem representation. It is -expected that a bootloader like uboot provides a bit more support, -that will be discussed later as well. - -Note: The block has to be in main memory. It has to be accessible in -both real mode and virtual mode with no mapping other than main -memory. If you are writing a simple flash bootloader, it should copy -the block to RAM before passing it to the kernel. - - -1) Header ---------- - - The kernel is entered with r3 pointing to an area of memory that is - roughly described in arch/powerpc/include/asm/prom.h by the structure - boot_param_header: - -struct boot_param_header { - u32 magic; /* magic word OF_DT_HEADER */ - u32 totalsize; /* total size of DT block */ - u32 off_dt_struct; /* offset to structure */ - u32 off_dt_strings; /* offset to strings */ - u32 off_mem_rsvmap; /* offset to memory reserve map - */ - u32 version; /* format version */ - u32 last_comp_version; /* last compatible version */ - - /* version 2 fields below */ - u32 boot_cpuid_phys; /* Which physical CPU id we're - booting on */ - /* version 3 fields below */ - u32 size_dt_strings; /* size of the strings block */ - - /* version 17 fields below */ - u32 size_dt_struct; /* size of the DT structure block */ -}; - - Along with the constants: - -/* Definitions used by the flattened device tree */ -#define OF_DT_HEADER 0xd00dfeed /* 4: version, - 4: total size */ -#define OF_DT_BEGIN_NODE 0x1 /* Start node: full name - */ -#define OF_DT_END_NODE 0x2 /* End node */ -#define OF_DT_PROP 0x3 /* Property: name off, - size, content */ -#define OF_DT_END 0x9 - - All values in this header are in big endian format, the various - fields in this header are defined more precisely below. All - "offset" values are in bytes from the start of the header; that is - from the value of r3. - - - magic - - This is a magic value that "marks" the beginning of the - device-tree block header. It contains the value 0xd00dfeed and is - defined by the constant OF_DT_HEADER - - - totalsize - - This is the total size of the DT block including the header. The - "DT" block should enclose all data structures defined in this - chapter (who are pointed to by offsets in this header). That is, - the device-tree structure, strings, and the memory reserve map. - - - off_dt_struct - - This is an offset from the beginning of the header to the start - of the "structure" part the device tree. (see 2) device tree) - - - off_dt_strings - - This is an offset from the beginning of the header to the start - of the "strings" part of the device-tree - - - off_mem_rsvmap - - This is an offset from the beginning of the header to the start - of the reserved memory map. This map is a list of pairs of 64- - bit integers. Each pair is a physical address and a size. The - list is terminated by an entry of size 0. This map provides the - kernel with a list of physical memory areas that are "reserved" - and thus not to be used for memory allocations, especially during - early initialization. The kernel needs to allocate memory during - boot for things like un-flattening the device-tree, allocating an - MMU hash table, etc... Those allocations must be done in such a - way to avoid overriding critical things like, on Open Firmware - capable machines, the RTAS instance, or on some pSeries, the TCE - tables used for the iommu. Typically, the reserve map should - contain _at least_ this DT block itself (header,total_size). If - you are passing an initrd to the kernel, you should reserve it as - well. You do not need to reserve the kernel image itself. The map - should be 64-bit aligned. - - - version - - This is the version of this structure. Version 1 stops - here. Version 2 adds an additional field boot_cpuid_phys. - Version 3 adds the size of the strings block, allowing the kernel - to reallocate it easily at boot and free up the unused flattened - structure after expansion. Version 16 introduces a new more - "compact" format for the tree itself that is however not backward - compatible. Version 17 adds an additional field, size_dt_struct, - allowing it to be reallocated or moved more easily (this is - particularly useful for bootloaders which need to make - adjustments to a device tree based on probed information). You - should always generate a structure of the highest version defined - at the time of your implementation. Currently that is version 17, - unless you explicitly aim at being backward compatible. - - - last_comp_version - - Last compatible version. This indicates down to what version of - the DT block you are backward compatible. For example, version 2 - is backward compatible with version 1 (that is, a kernel build - for version 1 will be able to boot with a version 2 format). You - should put a 1 in this field if you generate a device tree of - version 1 to 3, or 16 if you generate a tree of version 16 or 17 - using the new unit name format. - - - boot_cpuid_phys - - This field only exist on version 2 headers. It indicate which - physical CPU ID is calling the kernel entry point. This is used, - among others, by kexec. If you are on an SMP system, this value - should match the content of the "reg" property of the CPU node in - the device-tree corresponding to the CPU calling the kernel entry - point (see further chapters for more informations on the required - device-tree contents) - - - size_dt_strings - - This field only exists on version 3 and later headers. It - gives the size of the "strings" section of the device tree (which - starts at the offset given by off_dt_strings). - - - size_dt_struct - - This field only exists on version 17 and later headers. It gives - the size of the "structure" section of the device tree (which - starts at the offset given by off_dt_struct). - - So the typical layout of a DT block (though the various parts don't - need to be in that order) looks like this (addresses go from top to - bottom): - - - ------------------------------ - r3 -> | struct boot_param_header | - ------------------------------ - | (alignment gap) (*) | - ------------------------------ - | memory reserve map | - ------------------------------ - | (alignment gap) | - ------------------------------ - | | - | device-tree structure | - | | - ------------------------------ - | (alignment gap) | - ------------------------------ - | | - | device-tree strings | - | | - -----> ------------------------------ - | - | - --- (r3 + totalsize) - - (*) The alignment gaps are not necessarily present; their presence - and size are dependent on the various alignment requirements of - the individual data blocks. - - -2) Device tree generalities ---------------------------- - -This device-tree itself is separated in two different blocks, a -structure block and a strings block. Both need to be aligned to a 4 -byte boundary. - -First, let's quickly describe the device-tree concept before detailing -the storage format. This chapter does _not_ describe the detail of the -required types of nodes & properties for the kernel, this is done -later in chapter III. - -The device-tree layout is strongly inherited from the definition of -the Open Firmware IEEE 1275 device-tree. It's basically a tree of -nodes, each node having two or more named properties. A property can -have a value or not. - -It is a tree, so each node has one and only one parent except for the -root node who has no parent. - -A node has 2 names. The actual node name is generally contained in a -property of type "name" in the node property list whose value is a -zero terminated string and is mandatory for version 1 to 3 of the -format definition (as it is in Open Firmware). Version 16 makes it -optional as it can generate it from the unit name defined below. - -There is also a "unit name" that is used to differentiate nodes with -the same name at the same level, it is usually made of the node -names, the "@" sign, and a "unit address", which definition is -specific to the bus type the node sits on. - -The unit name doesn't exist as a property per-se but is included in -the device-tree structure. It is typically used to represent "path" in -the device-tree. More details about the actual format of these will be -below. - -The kernel powerpc generic code does not make any formal use of the -unit address (though some board support code may do) so the only real -requirement here for the unit address is to ensure uniqueness of -the node unit name at a given level of the tree. Nodes with no notion -of address and no possible sibling of the same name (like /memory or -/cpus) may omit the unit address in the context of this specification, -or use the "@0" default unit address. The unit name is used to define -a node "full path", which is the concatenation of all parent node -unit names separated with "/". - -The root node doesn't have a defined name, and isn't required to have -a name property either if you are using version 3 or earlier of the -format. It also has no unit address (no @ symbol followed by a unit -address). The root node unit name is thus an empty string. The full -path to the root node is "/". - -Every node which actually represents an actual device (that is, a node -which isn't only a virtual "container" for more nodes, like "/cpus" -is) is also required to have a "device_type" property indicating the -type of node . - -Finally, every node that can be referenced from a property in another -node is required to have a "linux,phandle" property. Real open -firmware implementations provide a unique "phandle" value for every -node that the "prom_init()" trampoline code turns into -"linux,phandle" properties. However, this is made optional if the -flattened device tree is used directly. An example of a node -referencing another node via "phandle" is when laying out the -interrupt tree which will be described in a further version of this -document. - -This "linux, phandle" property is a 32-bit value that uniquely -identifies a node. You are free to use whatever values or system of -values, internal pointers, or whatever to generate these, the only -requirement is that every node for which you provide that property has -a unique value for it. - -Here is an example of a simple device-tree. In this example, an "o" -designates a node followed by the node unit name. Properties are -presented with their name followed by their content. "content" -represents an ASCII string (zero terminated) value, while <content> -represents a 32-bit hexadecimal value. The various nodes in this -example will be discussed in a later chapter. At this point, it is -only meant to give you a idea of what a device-tree looks like. I have -purposefully kept the "name" and "linux,phandle" properties which -aren't necessary in order to give you a better idea of what the tree -looks like in practice. - - / o device-tree - |- name = "device-tree" - |- model = "MyBoardName" - |- compatible = "MyBoardFamilyName" - |- #address-cells = <2> - |- #size-cells = <2> - |- linux,phandle = <0> - | - o cpus - | | - name = "cpus" - | | - linux,phandle = <1> - | | - #address-cells = <1> - | | - #size-cells = <0> - | | - | o PowerPC,970@0 - | |- name = "PowerPC,970" - | |- device_type = "cpu" - | |- reg = <0> - | |- clock-frequency = <5f5e1000> - | |- 64-bit - | |- linux,phandle = <2> - | - o memory@0 - | |- name = "memory" - | |- device_type = "memory" - | |- reg = <00000000 00000000 00000000 20000000> - | |- linux,phandle = <3> - | - o chosen - |- name = "chosen" - |- bootargs = "root=/dev/sda2" - |- linux,phandle = <4> - -This tree is almost a minimal tree. It pretty much contains the -minimal set of required nodes and properties to boot a linux kernel; -that is, some basic model informations at the root, the CPUs, and the -physical memory layout. It also includes misc information passed -through /chosen, like in this example, the platform type (mandatory) -and the kernel command line arguments (optional). - -The /cpus/PowerPC,970@0/64-bit property is an example of a -property without a value. All other properties have a value. The -significance of the #address-cells and #size-cells properties will be -explained in chapter IV which defines precisely the required nodes and -properties and their content. - - -3) Device tree "structure" block - -The structure of the device tree is a linearized tree structure. The -"OF_DT_BEGIN_NODE" token starts a new node, and the "OF_DT_END_NODE" -ends that node definition. Child nodes are simply defined before -"OF_DT_END_NODE" (that is nodes within the node). A 'token' is a 32 -bit value. The tree has to be "finished" with a OF_DT_END token - -Here's the basic structure of a single node: - - * token OF_DT_BEGIN_NODE (that is 0x00000001) - * for version 1 to 3, this is the node full path as a zero - terminated string, starting with "/". For version 16 and later, - this is the node unit name only (or an empty string for the - root node) - * [align gap to next 4 bytes boundary] - * for each property: - * token OF_DT_PROP (that is 0x00000003) - * 32-bit value of property value size in bytes (or 0 if no - value) - * 32-bit value of offset in string block of property name - * property value data if any - * [align gap to next 4 bytes boundary] - * [child nodes if any] - * token OF_DT_END_NODE (that is 0x00000002) - -So the node content can be summarized as a start token, a full path, -a list of properties, a list of child nodes, and an end token. Every -child node is a full node structure itself as defined above. - -NOTE: The above definition requires that all property definitions for -a particular node MUST precede any subnode definitions for that node. -Although the structure would not be ambiguous if properties and -subnodes were intermingled, the kernel parser requires that the -properties come first (up until at least 2.6.22). Any tools -manipulating a flattened tree must take care to preserve this -constraint. - -4) Device tree "strings" block - -In order to save space, property names, which are generally redundant, -are stored separately in the "strings" block. This block is simply the -whole bunch of zero terminated strings for all property names -concatenated together. The device-tree property definitions in the -structure block will contain offset values from the beginning of the -strings block. - - -III - Required content of the device tree -========================================= - -WARNING: All "linux,*" properties defined in this document apply only -to a flattened device-tree. If your platform uses a real -implementation of Open Firmware or an implementation compatible with -the Open Firmware client interface, those properties will be created -by the trampoline code in the kernel's prom_init() file. For example, -that's where you'll have to add code to detect your board model and -set the platform number. However, when using the flattened device-tree -entry point, there is no prom_init() pass, and thus you have to -provide those properties yourself. - - -1) Note about cells and address representation ----------------------------------------------- - -The general rule is documented in the various Open Firmware -documentations. If you choose to describe a bus with the device-tree -and there exist an OF bus binding, then you should follow the -specification. However, the kernel does not require every single -device or bus to be described by the device tree. - -In general, the format of an address for a device is defined by the -parent bus type, based on the #address-cells and #size-cells -properties. Note that the parent's parent definitions of #address-cells -and #size-cells are not inherited so every node with children must specify -them. The kernel requires the root node to have those properties defining -addresses format for devices directly mapped on the processor bus. - -Those 2 properties define 'cells' for representing an address and a -size. A "cell" is a 32-bit number. For example, if both contain 2 -like the example tree given above, then an address and a size are both -composed of 2 cells, and each is a 64-bit number (cells are -concatenated and expected to be in big endian format). Another example -is the way Apple firmware defines them, with 2 cells for an address -and one cell for a size. Most 32-bit implementations should define -#address-cells and #size-cells to 1, which represents a 32-bit value. -Some 32-bit processors allow for physical addresses greater than 32 -bits; these processors should define #address-cells as 2. - -"reg" properties are always a tuple of the type "address size" where -the number of cells of address and size is specified by the bus -#address-cells and #size-cells. When a bus supports various address -spaces and other flags relative to a given address allocation (like -prefetchable, etc...) those flags are usually added to the top level -bits of the physical address. For example, a PCI physical address is -made of 3 cells, the bottom two containing the actual address itself -while the top cell contains address space indication, flags, and pci -bus & device numbers. - -For busses that support dynamic allocation, it's the accepted practice -to then not provide the address in "reg" (keep it 0) though while -providing a flag indicating the address is dynamically allocated, and -then, to provide a separate "assigned-addresses" property that -contains the fully allocated addresses. See the PCI OF bindings for -details. - -In general, a simple bus with no address space bits and no dynamic -allocation is preferred if it reflects your hardware, as the existing -kernel address parsing functions will work out of the box. If you -define a bus type with a more complex address format, including things -like address space bits, you'll have to add a bus translator to the -prom_parse.c file of the recent kernels for your bus type. - -The "reg" property only defines addresses and sizes (if #size-cells is -non-0) within a given bus. In order to translate addresses upward -(that is into parent bus addresses, and possibly into CPU physical -addresses), all busses must contain a "ranges" property. If the -"ranges" property is missing at a given level, it's assumed that -translation isn't possible, i.e., the registers are not visible on the -parent bus. The format of the "ranges" property for a bus is a list -of: - - bus address, parent bus address, size - -"bus address" is in the format of the bus this bus node is defining, -that is, for a PCI bridge, it would be a PCI address. Thus, (bus -address, size) defines a range of addresses for child devices. "parent -bus address" is in the format of the parent bus of this bus. For -example, for a PCI host controller, that would be a CPU address. For a -PCI<->ISA bridge, that would be a PCI address. It defines the base -address in the parent bus where the beginning of that range is mapped. - -For a new 64-bit powerpc board, I recommend either the 2/2 format or -Apple's 2/1 format which is slightly more compact since sizes usually -fit in a single 32-bit word. New 32-bit powerpc boards should use a -1/1 format, unless the processor supports physical addresses greater -than 32-bits, in which case a 2/1 format is recommended. - -Alternatively, the "ranges" property may be empty, indicating that the -registers are visible on the parent bus using an identity mapping -translation. In other words, the parent bus address space is the same -as the child bus address space. - -2) Note about "compatible" properties -------------------------------------- - -These properties are optional, but recommended in devices and the root -node. The format of a "compatible" property is a list of concatenated -zero terminated strings. They allow a device to express its -compatibility with a family of similar devices, in some cases, -allowing a single driver to match against several devices regardless -of their actual names. - -3) Note about "name" properties -------------------------------- - -While earlier users of Open Firmware like OldWorld macintoshes tended -to use the actual device name for the "name" property, it's nowadays -considered a good practice to use a name that is closer to the device -class (often equal to device_type). For example, nowadays, ethernet -controllers are named "ethernet", an additional "model" property -defining precisely the chip type/model, and "compatible" property -defining the family in case a single driver can driver more than one -of these chips. However, the kernel doesn't generally put any -restriction on the "name" property; it is simply considered good -practice to follow the standard and its evolutions as closely as -possible. - -Note also that the new format version 16 makes the "name" property -optional. If it's absent for a node, then the node's unit name is then -used to reconstruct the name. That is, the part of the unit name -before the "@" sign is used (or the entire unit name if no "@" sign -is present). - -4) Note about node and property names and character set -------------------------------------------------------- - -While open firmware provides more flexible usage of 8859-1, this -specification enforces more strict rules. Nodes and properties should -be comprised only of ASCII characters 'a' to 'z', '0' to -'9', ',', '.', '_', '+', '#', '?', and '-'. Node names additionally -allow uppercase characters 'A' to 'Z' (property names should be -lowercase. The fact that vendors like Apple don't respect this rule is -irrelevant here). Additionally, node and property names should always -begin with a character in the range 'a' to 'z' (or 'A' to 'Z' for node -names). - -The maximum number of characters for both nodes and property names -is 31. In the case of node names, this is only the leftmost part of -a unit name (the pure "name" property), it doesn't include the unit -address which can extend beyond that limit. - - -5) Required nodes and properties --------------------------------- - These are all that are currently required. However, it is strongly - recommended that you expose PCI host bridges as documented in the - PCI binding to open firmware, and your interrupt tree as documented - in OF interrupt tree specification. - - a) The root node - - The root node requires some properties to be present: - - - model : this is your board name/model - - #address-cells : address representation for "root" devices - - #size-cells: the size representation for "root" devices - - device_type : This property shouldn't be necessary. However, if - you decide to create a device_type for your root node, make sure it - is _not_ "chrp" unless your platform is a pSeries or PAPR compliant - one for 64-bit, or a CHRP-type machine for 32-bit as this will - matched by the kernel this way. - - Additionally, some recommended properties are: - - - compatible : the board "family" generally finds its way here, - for example, if you have 2 board models with a similar layout, - that typically get driven by the same platform code in the - kernel, you would use a different "model" property but put a - value in "compatible". The kernel doesn't directly use that - value but it is generally useful. - - The root node is also generally where you add additional properties - specific to your board like the serial number if any, that sort of - thing. It is recommended that if you add any "custom" property whose - name may clash with standard defined ones, you prefix them with your - vendor name and a comma. - - b) The /cpus node - - This node is the parent of all individual CPU nodes. It doesn't - have any specific requirements, though it's generally good practice - to have at least: - - #address-cells = <00000001> - #size-cells = <00000000> - - This defines that the "address" for a CPU is a single cell, and has - no meaningful size. This is not necessary but the kernel will assume - that format when reading the "reg" properties of a CPU node, see - below - - c) The /cpus/* nodes - - So under /cpus, you are supposed to create a node for every CPU on - the machine. There is no specific restriction on the name of the - CPU, though It's common practice to call it PowerPC,<name>. For - example, Apple uses PowerPC,G5 while IBM uses PowerPC,970FX. - - Required properties: - - - device_type : has to be "cpu" - - reg : This is the physical CPU number, it's a single 32-bit cell - and is also used as-is as the unit number for constructing the - unit name in the full path. For example, with 2 CPUs, you would - have the full path: - /cpus/PowerPC,970FX@0 - /cpus/PowerPC,970FX@1 - (unit addresses do not require leading zeroes) - - d-cache-block-size : one cell, L1 data cache block size in bytes (*) - - i-cache-block-size : one cell, L1 instruction cache block size in - bytes - - d-cache-size : one cell, size of L1 data cache in bytes - - i-cache-size : one cell, size of L1 instruction cache in bytes - -(*) The cache "block" size is the size on which the cache management -instructions operate. Historically, this document used the cache -"line" size here which is incorrect. The kernel will prefer the cache -block size and will fallback to cache line size for backward -compatibility. - - Recommended properties: - - - timebase-frequency : a cell indicating the frequency of the - timebase in Hz. This is not directly used by the generic code, - but you are welcome to copy/paste the pSeries code for setting - the kernel timebase/decrementer calibration based on this - value. - - clock-frequency : a cell indicating the CPU core clock frequency - in Hz. A new property will be defined for 64-bit values, but if - your frequency is < 4Ghz, one cell is enough. Here as well as - for the above, the common code doesn't use that property, but - you are welcome to re-use the pSeries or Maple one. A future - kernel version might provide a common function for this. - - d-cache-line-size : one cell, L1 data cache line size in bytes - if different from the block size - - i-cache-line-size : one cell, L1 instruction cache line size in - bytes if different from the block size - - You are welcome to add any property you find relevant to your board, - like some information about the mechanism used to soft-reset the - CPUs. For example, Apple puts the GPIO number for CPU soft reset - lines in there as a "soft-reset" property since they start secondary - CPUs by soft-resetting them. - - - d) the /memory node(s) - - To define the physical memory layout of your board, you should - create one or more memory node(s). You can either create a single - node with all memory ranges in its reg property, or you can create - several nodes, as you wish. The unit address (@ part) used for the - full path is the address of the first range of memory defined by a - given node. If you use a single memory node, this will typically be - @0. - - Required properties: - - - device_type : has to be "memory" - - reg : This property contains all the physical memory ranges of - your board. It's a list of addresses/sizes concatenated - together, with the number of cells of each defined by the - #address-cells and #size-cells of the root node. For example, - with both of these properties being 2 like in the example given - earlier, a 970 based machine with 6Gb of RAM could typically - have a "reg" property here that looks like: - - 00000000 00000000 00000000 80000000 - 00000001 00000000 00000001 00000000 - - That is a range starting at 0 of 0x80000000 bytes and a range - starting at 0x100000000 and of 0x100000000 bytes. You can see - that there is no memory covering the IO hole between 2Gb and - 4Gb. Some vendors prefer splitting those ranges into smaller - segments, but the kernel doesn't care. - - e) The /chosen node - - This node is a bit "special". Normally, that's where open firmware - puts some variable environment information, like the arguments, or - the default input/output devices. - - This specification makes a few of these mandatory, but also defines - some linux-specific properties that would be normally constructed by - the prom_init() trampoline when booting with an OF client interface, - but that you have to provide yourself when using the flattened format. - - Recommended properties: - - - bootargs : This zero-terminated string is passed as the kernel - command line - - linux,stdout-path : This is the full path to your standard - console device if any. Typically, if you have serial devices on - your board, you may want to put the full path to the one set as - the default console in the firmware here, for the kernel to pick - it up as its own default console. If you look at the function - set_preferred_console() in arch/ppc64/kernel/setup.c, you'll see - that the kernel tries to find out the default console and has - knowledge of various types like 8250 serial ports. You may want - to extend this function to add your own. - - Note that u-boot creates and fills in the chosen node for platforms - that use it. - - (Note: a practice that is now obsolete was to include a property - under /chosen called interrupt-controller which had a phandle value - that pointed to the main interrupt controller) - - f) the /soc<SOCname> node - - This node is used to represent a system-on-a-chip (SOC) and must be - present if the processor is a SOC. The top-level soc node contains - information that is global to all devices on the SOC. The node name - should contain a unit address for the SOC, which is the base address - of the memory-mapped register set for the SOC. The name of an soc - node should start with "soc", and the remainder of the name should - represent the part number for the soc. For example, the MPC8540's - soc node would be called "soc8540". - - Required properties: - - - device_type : Should be "soc" - - ranges : Should be defined as specified in 1) to describe the - translation of SOC addresses for memory mapped SOC registers. - - bus-frequency: Contains the bus frequency for the SOC node. - Typically, the value of this field is filled in by the boot - loader. - - - Recommended properties: - - - reg : This property defines the address and size of the - memory-mapped registers that are used for the SOC node itself. - It does not include the child device registers - these will be - defined inside each child node. The address specified in the - "reg" property should match the unit address of the SOC node. - - #address-cells : Address representation for "soc" devices. The - format of this field may vary depending on whether or not the - device registers are memory mapped. For memory mapped - registers, this field represents the number of cells needed to - represent the address of the registers. For SOCs that do not - use MMIO, a special address format should be defined that - contains enough cells to represent the required information. - See 1) above for more details on defining #address-cells. - - #size-cells : Size representation for "soc" devices - - #interrupt-cells : Defines the width of cells used to represent - interrupts. Typically this value is <2>, which includes a - 32-bit number that represents the interrupt number, and a - 32-bit number that represents the interrupt sense and level. - This field is only needed if the SOC contains an interrupt - controller. - - The SOC node may contain child nodes for each SOC device that the - platform uses. Nodes should not be created for devices which exist - on the SOC but are not used by a particular platform. See chapter VI - for more information on how to specify devices that are part of a SOC. - - Example SOC node for the MPC8540: - - soc8540@e0000000 { - #address-cells = <1>; - #size-cells = <1>; - #interrupt-cells = <2>; - device_type = "soc"; - ranges = <00000000 e0000000 00100000> - reg = <e0000000 00003000>; - bus-frequency = <0>; - } - - - -IV - "dtc", the device tree compiler -==================================== - - -dtc source code can be found at -<http://git.jdl.com/gitweb/?p=dtc.git> - -WARNING: This version is still in early development stage; the -resulting device-tree "blobs" have not yet been validated with the -kernel. The current generated block lacks a useful reserve map (it will -be fixed to generate an empty one, it's up to the bootloader to fill -it up) among others. The error handling needs work, bugs are lurking, -etc... - -dtc basically takes a device-tree in a given format and outputs a -device-tree in another format. The currently supported formats are: - - Input formats: - ------------- - - - "dtb": "blob" format, that is a flattened device-tree block - with - header all in a binary blob. - - "dts": "source" format. This is a text file containing a - "source" for a device-tree. The format is defined later in this - chapter. - - "fs" format. This is a representation equivalent to the - output of /proc/device-tree, that is nodes are directories and - properties are files - - Output formats: - --------------- - - - "dtb": "blob" format - - "dts": "source" format - - "asm": assembly language file. This is a file that can be - sourced by gas to generate a device-tree "blob". That file can - then simply be added to your Makefile. Additionally, the - assembly file exports some symbols that can be used. - - -The syntax of the dtc tool is - - dtc [-I <input-format>] [-O <output-format>] - [-o output-filename] [-V output_version] input_filename - - -The "output_version" defines what version of the "blob" format will be -generated. Supported versions are 1,2,3 and 16. The default is -currently version 3 but that may change in the future to version 16. - -Additionally, dtc performs various sanity checks on the tree, like the -uniqueness of linux, phandle properties, validity of strings, etc... - -The format of the .dts "source" file is "C" like, supports C and C++ -style comments. - -/ { -} - -The above is the "device-tree" definition. It's the only statement -supported currently at the toplevel. - -/ { - property1 = "string_value"; /* define a property containing a 0 - * terminated string - */ - - property2 = <1234abcd>; /* define a property containing a - * numerical 32-bit value (hexadecimal) - */ - - property3 = <12345678 12345678 deadbeef>; - /* define a property containing 3 - * numerical 32-bit values (cells) in - * hexadecimal - */ - property4 = [0a 0b 0c 0d de ea ad be ef]; - /* define a property whose content is - * an arbitrary array of bytes - */ - - childnode@address { /* define a child node named "childnode" - * whose unit name is "childnode at - * address" - */ - - childprop = "hello\n"; /* define a property "childprop" of - * childnode (in this case, a string) - */ - }; -}; - -Nodes can contain other nodes etc... thus defining the hierarchical -structure of the tree. - -Strings support common escape sequences from C: "\n", "\t", "\r", -"\(octal value)", "\x(hex value)". - -It is also suggested that you pipe your source file through cpp (gcc -preprocessor) so you can use #include's, #define for constants, etc... - -Finally, various options are planned but not yet implemented, like -automatic generation of phandles, labels (exported to the asm file so -you can point to a property content and change it easily from whatever -you link the device-tree with), label or path instead of numeric value -in some cells to "point" to a node (replaced by a phandle at compile -time), export of reserve map address to the asm file, ability to -specify reserve map content at compile time, etc... - -We may provide a .h include file with common definitions of that -proves useful for some properties (like building PCI properties or -interrupt maps) though it may be better to add a notion of struct -definitions to the compiler... - - -V - Recommendations for a bootloader -==================================== - - -Here are some various ideas/recommendations that have been proposed -while all this has been defined and implemented. - - - The bootloader may want to be able to use the device-tree itself - and may want to manipulate it (to add/edit some properties, - like physical memory size or kernel arguments). At this point, 2 - choices can be made. Either the bootloader works directly on the - flattened format, or the bootloader has its own internal tree - representation with pointers (similar to the kernel one) and - re-flattens the tree when booting the kernel. The former is a bit - more difficult to edit/modify, the later requires probably a bit - more code to handle the tree structure. Note that the structure - format has been designed so it's relatively easy to "insert" - properties or nodes or delete them by just memmoving things - around. It contains no internal offsets or pointers for this - purpose. - - - An example of code for iterating nodes & retrieving properties - directly from the flattened tree format can be found in the kernel - file arch/ppc64/kernel/prom.c, look at scan_flat_dt() function, - its usage in early_init_devtree(), and the corresponding various - early_init_dt_scan_*() callbacks. That code can be re-used in a - GPL bootloader, and as the author of that code, I would be happy - to discuss possible free licensing to any vendor who wishes to - integrate all or part of this code into a non-GPL bootloader. - - - -VI - System-on-a-chip devices and nodes -======================================= - -Many companies are now starting to develop system-on-a-chip -processors, where the processor core (CPU) and many peripheral devices -exist on a single piece of silicon. For these SOCs, an SOC node -should be used that defines child nodes for the devices that make -up the SOC. While platforms are not required to use this model in -order to boot the kernel, it is highly encouraged that all SOC -implementations define as complete a flat-device-tree as possible to -describe the devices on the SOC. This will allow for the -genericization of much of the kernel code. - - -1) Defining child nodes of an SOC ---------------------------------- - -Each device that is part of an SOC may have its own node entry inside -the SOC node. For each device that is included in the SOC, the unit -address property represents the address offset for this device's -memory-mapped registers in the parent's address space. The parent's -address space is defined by the "ranges" property in the top-level soc -node. The "reg" property for each node that exists directly under the -SOC node should contain the address mapping from the child address space -to the parent SOC address space and the size of the device's -memory-mapped register file. - -For many devices that may exist inside an SOC, there are predefined -specifications for the format of the device tree node. All SOC child -nodes should follow these specifications, except where noted in this -document. - -See appendix A for an example partial SOC node definition for the -MPC8540. - - -2) Representing devices without a current OF specification ----------------------------------------------------------- - -Currently, there are many devices on SOCs that do not have a standard -representation pre-defined as part of the open firmware -specifications, mainly because the boards that contain these SOCs are -not currently booted using open firmware. This section contains -descriptions for the SOC devices for which new nodes have been -defined; this list will expand as more and more SOC-containing -platforms are moved over to use the flattened-device-tree model. - -VII - Specifying interrupt information for devices -=================================================== - -The device tree represents the busses and devices of a hardware -system in a form similar to the physical bus topology of the -hardware. - -In addition, a logical 'interrupt tree' exists which represents the -hierarchy and routing of interrupts in the hardware. - -The interrupt tree model is fully described in the -document "Open Firmware Recommended Practice: Interrupt -Mapping Version 0.9". The document is available at: -<http://playground.sun.com/1275/practice>. - -1) interrupts property ----------------------- - -Devices that generate interrupts to a single interrupt controller -should use the conventional OF representation described in the -OF interrupt mapping documentation. - -Each device which generates interrupts must have an 'interrupt' -property. The interrupt property value is an arbitrary number of -of 'interrupt specifier' values which describe the interrupt or -interrupts for the device. - -The encoding of an interrupt specifier is determined by the -interrupt domain in which the device is located in the -interrupt tree. The root of an interrupt domain specifies in -its #interrupt-cells property the number of 32-bit cells -required to encode an interrupt specifier. See the OF interrupt -mapping documentation for a detailed description of domains. - -For example, the binding for the OpenPIC interrupt controller -specifies an #interrupt-cells value of 2 to encode the interrupt -number and level/sense information. All interrupt children in an -OpenPIC interrupt domain use 2 cells per interrupt in their interrupts -property. - -The PCI bus binding specifies a #interrupt-cell value of 1 to encode -which interrupt pin (INTA,INTB,INTC,INTD) is used. - -2) interrupt-parent property ----------------------------- - -The interrupt-parent property is specified to define an explicit -link between a device node and its interrupt parent in -the interrupt tree. The value of interrupt-parent is the -phandle of the parent node. - -If the interrupt-parent property is not defined for a node, its -interrupt parent is assumed to be an ancestor in the node's -_device tree_ hierarchy. - -3) OpenPIC Interrupt Controllers --------------------------------- - -OpenPIC interrupt controllers require 2 cells to encode -interrupt information. The first cell defines the interrupt -number. The second cell defines the sense and level -information. - -Sense and level information should be encoded as follows: - - 0 = low to high edge sensitive type enabled - 1 = active low level sensitive type enabled - 2 = active high level sensitive type enabled - 3 = high to low edge sensitive type enabled - -4) ISA Interrupt Controllers ----------------------------- - -ISA PIC interrupt controllers require 2 cells to encode -interrupt information. The first cell defines the interrupt -number. The second cell defines the sense and level -information. - -ISA PIC interrupt controllers should adhere to the ISA PIC -encodings listed below: - - 0 = active low level sensitive type enabled - 1 = active high level sensitive type enabled - 2 = high to low edge sensitive type enabled - 3 = low to high edge sensitive type enabled - -VIII - Specifying Device Power Management Information (sleep property) -=================================================================== - -Devices on SOCs often have mechanisms for placing devices into low-power -states that are decoupled from the devices' own register blocks. Sometimes, -this information is more complicated than a cell-index property can -reasonably describe. Thus, each device controlled in such a manner -may contain a "sleep" property which describes these connections. - -The sleep property consists of one or more sleep resources, each of -which consists of a phandle to a sleep controller, followed by a -controller-specific sleep specifier of zero or more cells. - -The semantics of what type of low power modes are possible are defined -by the sleep controller. Some examples of the types of low power modes -that may be supported are: - - - Dynamic: The device may be disabled or enabled at any time. - - System Suspend: The device may request to be disabled or remain - awake during system suspend, but will not be disabled until then. - - Permanent: The device is disabled permanently (until the next hard - reset). - -Some devices may share a clock domain with each other, such that they should -only be suspended when none of the devices are in use. Where reasonable, -such nodes should be placed on a virtual bus, where the bus has the sleep -property. If the clock domain is shared among devices that cannot be -reasonably grouped in this manner, then create a virtual sleep controller -(similar to an interrupt nexus, except that defining a standardized -sleep-map should wait until its necessity is demonstrated). - -Appendix A - Sample SOC node for MPC8540 -======================================== - - soc@e0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8540-ccsr", "simple-bus"; - device_type = "soc"; - ranges = <0x00000000 0xe0000000 0x00100000> - bus-frequency = <0>; - interrupt-parent = <&pic>; - - ethernet@24000 { - #address-cells = <1>; - #size-cells = <1>; - device_type = "network"; - model = "TSEC"; - compatible = "gianfar", "simple-bus"; - reg = <0x24000 0x1000>; - local-mac-address = [ 00 E0 0C 00 73 00 ]; - interrupts = <29 2 30 2 34 2>; - phy-handle = <&phy0>; - sleep = <&pmc 00000080>; - ranges; - - mdio@24520 { - reg = <0x24520 0x20>; - compatible = "fsl,gianfar-mdio"; - - phy0: ethernet-phy@0 { - interrupts = <5 1>; - reg = <0>; - device_type = "ethernet-phy"; - }; - - phy1: ethernet-phy@1 { - interrupts = <5 1>; - reg = <1>; - device_type = "ethernet-phy"; - }; - - phy3: ethernet-phy@3 { - interrupts = <7 1>; - reg = <3>; - device_type = "ethernet-phy"; - }; - }; - }; - - ethernet@25000 { - device_type = "network"; - model = "TSEC"; - compatible = "gianfar"; - reg = <0x25000 0x1000>; - local-mac-address = [ 00 E0 0C 00 73 01 ]; - interrupts = <13 2 14 2 18 2>; - phy-handle = <&phy1>; - sleep = <&pmc 00000040>; - }; - - ethernet@26000 { - device_type = "network"; - model = "FEC"; - compatible = "gianfar"; - reg = <0x26000 0x1000>; - local-mac-address = [ 00 E0 0C 00 73 02 ]; - interrupts = <41 2>; - phy-handle = <&phy3>; - sleep = <&pmc 00000020>; - }; - - serial@4500 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8540-duart", "simple-bus"; - sleep = <&pmc 00000002>; - ranges; - - serial@4500 { - device_type = "serial"; - compatible = "ns16550"; - reg = <0x4500 0x100>; - clock-frequency = <0>; - interrupts = <42 2>; - }; - - serial@4600 { - device_type = "serial"; - compatible = "ns16550"; - reg = <0x4600 0x100>; - clock-frequency = <0>; - interrupts = <42 2>; - }; - }; - - pic: pic@40000 { - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <2>; - reg = <0x40000 0x40000>; - compatible = "chrp,open-pic"; - device_type = "open-pic"; - }; - - i2c@3000 { - interrupts = <43 2>; - reg = <0x3000 0x100>; - compatible = "fsl-i2c"; - dfsrr; - sleep = <&pmc 00000004>; - }; - - pmc: power@e0070 { - compatible = "fsl,mpc8540-pmc", "fsl,mpc8548-pmc"; - reg = <0xe0070 0x20>; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/4xx/cpm.txt b/Documentation/powerpc/dts-bindings/4xx/cpm.txt deleted file mode 100644 index ee459806d35..00000000000 --- a/Documentation/powerpc/dts-bindings/4xx/cpm.txt +++ /dev/null @@ -1,52 +0,0 @@ -PPC4xx Clock Power Management (CPM) node - -Required properties: - - compatible : compatible list, currently only "ibm,cpm" - - dcr-access-method : "native" - - dcr-reg : < DCR register range > - -Optional properties: - - er-offset : All 4xx SoCs with a CPM controller have - one of two different order for the CPM - registers. Some have the CPM registers - in the following order (ER,FR,SR). The - others have them in the following order - (SR,ER,FR). For the second case set - er-offset = <1>. - - unused-units : specifier consist of one cell. For each - bit in the cell, the corresponding bit - in CPM will be set to turn off unused - devices. - - idle-doze : specifier consist of one cell. For each - bit in the cell, the corresponding bit - in CPM will be set to turn off unused - devices. This is usually just CPM[CPU]. - - standby : specifier consist of one cell. For each - bit in the cell, the corresponding bit - in CPM will be set on standby and - restored on resume. - - suspend : specifier consist of one cell. For each - bit in the cell, the corresponding bit - in CPM will be set on suspend (mem) and - restored on resume. Note, for standby - and suspend the corresponding bits can - be different or the same. Usually for - standby only class 2 and 3 units are set. - However, the interface does not care. - If they are the same, the additional - power saving will be seeing if support - is available to put the DDR in self - refresh mode and any additional power - saving techniques for the specific SoC. - -Example: - CPM0: cpm { - compatible = "ibm,cpm"; - dcr-access-method = "native"; - dcr-reg = <0x160 0x003>; - er-offset = <0>; - unused-units = <0x00000100>; - idle-doze = <0x02000000>; - standby = <0xfeff0000>; - suspend = <0xfeff791d>; -}; diff --git a/Documentation/powerpc/dts-bindings/4xx/emac.txt b/Documentation/powerpc/dts-bindings/4xx/emac.txt deleted file mode 100644 index 2161334a7ca..00000000000 --- a/Documentation/powerpc/dts-bindings/4xx/emac.txt +++ /dev/null @@ -1,148 +0,0 @@ - 4xx/Axon EMAC ethernet nodes - - The EMAC ethernet controller in IBM and AMCC 4xx chips, and also - the Axon bridge. To operate this needs to interact with a ths - special McMAL DMA controller, and sometimes an RGMII or ZMII - interface. In addition to the nodes and properties described - below, the node for the OPB bus on which the EMAC sits must have a - correct clock-frequency property. - - i) The EMAC node itself - - Required properties: - - device_type : "network" - - - compatible : compatible list, contains 2 entries, first is - "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, - 405gp, Axon) and second is either "ibm,emac" or - "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", - "ibm,emac4" - - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> - - interrupt-parent : optional, if needed for interrupt mapping - - reg : <registers mapping> - - local-mac-address : 6 bytes, MAC address - - mal-device : phandle of the associated McMAL node - - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated - with this EMAC - - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated - with this EMAC - - cell-index : 1 cell, hardware index of the EMAC cell on a given - ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on - each Axon chip) - - max-frame-size : 1 cell, maximum frame size supported in bytes - - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048 - - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec - operations. - For Axon, 2048. - - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate - thresholds). - For Axon, 0x00000010 - - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) - in bytes. - For Axon, 0x00000100 (I think ...) - - phy-mode : string, mode of operations of the PHY interface. - Supported values are: "mii", "rmii", "smii", "rgmii", - "tbi", "gmii", rtbi", "sgmii". - For Axon on CAB, it is "rgmii" - - mdio-device : 1 cell, required iff using shared MDIO registers - (440EP). phandle of the EMAC to use to drive the - MDIO lines for the PHY used by this EMAC. - - zmii-device : 1 cell, required iff connected to a ZMII. phandle of - the ZMII device node - - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII - channel or 0xffffffff if ZMII is only used for MDIO. - - rgmii-device : 1 cell, required iff connected to an RGMII. phandle - of the RGMII device node. - For Axon: phandle of plb5/plb4/opb/rgmii - - rgmii-channel : 1 cell, required iff connected to an RGMII. Which - RGMII channel is used by this EMAC. - Fox Axon: present, whatever value is appropriate for each - EMAC, that is the content of the current (bogus) "phy-port" - property. - - Optional properties: - - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, - a search is performed. - - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY - for, used if phy-address is absent. bit 0x00000001 is - MDIO address 0. - For Axon it can be absent, though my current driver - doesn't handle phy-address yet so for now, keep - 0x00ffffff in it. - - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - rx-fifo-size). For Axon, either absent or 2048. - - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec - operations (if absent the value is the same as - tx-fifo-size). For Axon, either absent or 2048. - - tah-device : 1 cell, optional. If connected to a TAH engine for - offload, phandle of the TAH device node. - - tah-channel : 1 cell, optional. If appropriate, channel used on the - TAH engine. - - Example: - - EMAC0: ethernet@40000800 { - device_type = "network"; - compatible = "ibm,emac-440gp", "ibm,emac"; - interrupt-parent = <&UIC1>; - interrupts = <1c 4 1d 4>; - reg = <40000800 70>; - local-mac-address = [00 04 AC E3 1B 1E]; - mal-device = <&MAL0>; - mal-tx-channel = <0 1>; - mal-rx-channel = <0>; - cell-index = <0>; - max-frame-size = <5dc>; - rx-fifo-size = <1000>; - tx-fifo-size = <800>; - phy-mode = "rmii"; - phy-map = <00000001>; - zmii-device = <&ZMII0>; - zmii-channel = <0>; - }; - - ii) McMAL node - - Required properties: - - device_type : "dma-controller" - - compatible : compatible list, containing 2 entries, first is - "ibm,mcmal-CHIP" where CHIP is the host ASIC (like - emac) and the second is either "ibm,mcmal" or - "ibm,mcmal2". - For Axon, "ibm,mcmal-axon","ibm,mcmal2" - - interrupts : <interrupt mapping for the MAL interrupts sources: - 5 sources: tx_eob, rx_eob, serr, txde, rxde>. - For Axon: This is _different_ from the current - firmware. We use the "delayed" interrupts for txeob - and rxeob. Thus we end up with mapping those 5 MPIC - interrupts, all level positive sensitive: 10, 11, 32, - 33, 34 (in decimal) - - dcr-reg : < DCR registers range > - - dcr-parent : if needed for dcr-reg - - num-tx-chans : 1 cell, number of Tx channels - - num-rx-chans : 1 cell, number of Rx channels - - iii) ZMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,zmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,zmii". - For Axon, there is no ZMII node. - - reg : <registers mapping> - - iv) RGMII node - - Required properties: - - compatible : compatible list, containing 2 entries, first is - "ibm,rgmii-CHIP" where CHIP is the host ASIC (like - EMAC) and the second is "ibm,rgmii". - For Axon, "ibm,rgmii-axon","ibm,rgmii" - - reg : <registers mapping> - - revision : as provided by the RGMII new version register if - available. - For Axon: 0x0000012a - diff --git a/Documentation/powerpc/dts-bindings/4xx/ndfc.txt b/Documentation/powerpc/dts-bindings/4xx/ndfc.txt deleted file mode 100644 index 869f0b5f16e..00000000000 --- a/Documentation/powerpc/dts-bindings/4xx/ndfc.txt +++ /dev/null @@ -1,39 +0,0 @@ -AMCC NDFC (NanD Flash Controller) - -Required properties: -- compatible : "ibm,ndfc". -- reg : should specify chip select and size used for the chip (0x2000). - -Optional properties: -- ccr : NDFC config and control register value (default 0). -- bank-settings : NDFC bank configuration register value (default 0). - -Notes: -- partition(s) - follows the OF MTD standard for partitions - -Example: - -ndfc@1,0 { - compatible = "ibm,ndfc"; - reg = <0x00000001 0x00000000 0x00002000>; - ccr = <0x00001000>; - bank-settings = <0x80002222>; - #address-cells = <1>; - #size-cells = <1>; - - nand { - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "kernel"; - reg = <0x00000000 0x00200000>; - }; - partition@200000 { - label = "root"; - reg = <0x00200000 0x03E00000>; - }; - }; -}; - - diff --git a/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt b/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt deleted file mode 100644 index 515ebcf1b97..00000000000 --- a/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt +++ /dev/null @@ -1,93 +0,0 @@ -PPC440SPe DMA/XOR (DMA Controller and XOR Accelerator) - -Device nodes needed for operation of the ppc440spe-adma driver -are specified hereby. These are I2O/DMA, DMA and XOR nodes -for DMA engines and Memory Queue Module node. The latter is used -by ADMA driver for configuration of RAID-6 H/W capabilities of -the PPC440SPe. In addition to the nodes and properties described -below, the ranges property of PLB node must specify ranges for -DMA devices. - - i) The I2O node - - Required properties: - - - compatible : "ibm,i2o-440spe"; - - reg : <registers mapping> - - dcr-reg : <DCR registers range> - - Example: - - I2O: i2o@400100000 { - compatible = "ibm,i2o-440spe"; - reg = <0x00000004 0x00100000 0x100>; - dcr-reg = <0x060 0x020>; - }; - - - ii) The DMA node - - Required properties: - - - compatible : "ibm,dma-440spe"; - - cell-index : 1 cell, hardware index of the DMA engine - (typically 0x0 and 0x1 for DMA0 and DMA1) - - reg : <registers mapping> - - dcr-reg : <DCR registers range> - - interrupts : <interrupt mapping for DMA0/1 interrupts sources: - 2 sources: DMAx CS FIFO Needs Service IRQ (on UIC0) - and DMA Error IRQ (on UIC1). The latter is common - for both DMA engines>. - - interrupt-parent : needed for interrupt mapping - - Example: - - DMA0: dma0@400100100 { - compatible = "ibm,dma-440spe"; - cell-index = <0>; - reg = <0x00000004 0x00100100 0x100>; - dcr-reg = <0x060 0x020>; - interrupt-parent = <&DMA0>; - interrupts = <0 1>; - #interrupt-cells = <1>; - #address-cells = <0>; - #size-cells = <0>; - interrupt-map = < - 0 &UIC0 0x14 4 - 1 &UIC1 0x16 4>; - }; - - - iii) XOR Accelerator node - - Required properties: - - - compatible : "amcc,xor-accelerator"; - - reg : <registers mapping> - - interrupts : <interrupt mapping for XOR interrupt source> - - interrupt-parent : for interrupt mapping - - Example: - - xor-accel@400200000 { - compatible = "amcc,xor-accelerator"; - reg = <0x00000004 0x00200000 0x400>; - interrupt-parent = <&UIC1>; - interrupts = <0x1f 4>; - }; - - - iv) Memory Queue Module node - - Required properties: - - - compatible : "ibm,mq-440spe"; - - dcr-reg : <DCR registers range> - - Example: - - MQ0: mq { - compatible = "ibm,mq-440spe"; - dcr-reg = <0x040 0x020>; - }; - diff --git a/Documentation/powerpc/dts-bindings/4xx/reboot.txt b/Documentation/powerpc/dts-bindings/4xx/reboot.txt deleted file mode 100644 index d7217260589..00000000000 --- a/Documentation/powerpc/dts-bindings/4xx/reboot.txt +++ /dev/null @@ -1,18 +0,0 @@ -Reboot property to control system reboot on PPC4xx systems: - -By setting "reset_type" to one of the following values, the default -software reset mechanism may be overidden. Here the possible values of -"reset_type": - - 1 - PPC4xx core reset - 2 - PPC4xx chip reset - 3 - PPC4xx system reset (default) - -Example: - - cpu@0 { - device_type = "cpu"; - model = "PowerPC,440SPe"; - ... - reset-type = <2>; /* Use chip-reset */ - }; diff --git a/Documentation/powerpc/dts-bindings/can/sja1000.txt b/Documentation/powerpc/dts-bindings/can/sja1000.txt deleted file mode 100644 index d6d209ded93..00000000000 --- a/Documentation/powerpc/dts-bindings/can/sja1000.txt +++ /dev/null @@ -1,53 +0,0 @@ -Memory mapped SJA1000 CAN controller from NXP (formerly Philips) - -Required properties: - -- compatible : should be "nxp,sja1000". - -- reg : should specify the chip select, address offset and size required - to map the registers of the SJA1000. The size is usually 0x80. - -- interrupts: property with a value describing the interrupt source - (number and sensitivity) required for the SJA1000. - -Optional properties: - -- nxp,external-clock-frequency : Frequency of the external oscillator - clock in Hz. Note that the internal clock frequency used by the - SJA1000 is half of that value. If not specified, a default value - of 16000000 (16 MHz) is used. - -- nxp,tx-output-mode : operation mode of the TX output control logic: - <0x0> : bi-phase output mode - <0x1> : normal output mode (default) - <0x2> : test output mode - <0x3> : clock output mode - -- nxp,tx-output-config : TX output pin configuration: - <0x01> : TX0 invert - <0x02> : TX0 pull-down (default) - <0x04> : TX0 pull-up - <0x06> : TX0 push-pull - <0x08> : TX1 invert - <0x10> : TX1 pull-down - <0x20> : TX1 pull-up - <0x30> : TX1 push-pull - -- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin. - If not specified or if the specified value is 0, the CLKOUT pin - will be disabled. - -- nxp,no-comparator-bypass : Allows to disable the CAN input comperator. - -For futher information, please have a look to the SJA1000 data sheet. - -Examples: - -can@3,100 { - compatible = "nxp,sja1000"; - reg = <3 0x100 0x80>; - interrupts = <2 0>; - interrupt-parent = <&mpic>; - nxp,external-clock-frequency = <16000000>; -}; - diff --git a/Documentation/powerpc/dts-bindings/ecm.txt b/Documentation/powerpc/dts-bindings/ecm.txt deleted file mode 100644 index f514f29c67d..00000000000 --- a/Documentation/powerpc/dts-bindings/ecm.txt +++ /dev/null @@ -1,64 +0,0 @@ -===================================================================== -E500 LAW & Coherency Module Device Tree Binding -Copyright (C) 2009 Freescale Semiconductor Inc. -===================================================================== - -Local Access Window (LAW) Node - -The LAW node represents the region of CCSR space where local access -windows are configured. For ECM based devices this is the first 4k -of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some -number of local access windows as specified by fsl,num-laws. - -PROPERTIES - - - compatible - Usage: required - Value type: <string> - Definition: Must include "fsl,ecm-law" - - - reg - Usage: required - Value type: <prop-encoded-array> - Definition: A standard property. The value specifies the - physical address offset and length of the CCSR space - registers. - - - fsl,num-laws - Usage: required - Value type: <u32> - Definition: The value specifies the number of local access - windows for this device. - -===================================================================== - -E500 Coherency Module Node - -The E500 LAW node represents the region of CCSR space where ECM config -and error reporting registers exist, this is the second 4k (0x1000) -of CCSR space. - -PROPERTIES - - - compatible - Usage: required - Value type: <string> - Definition: Must include "fsl,CHIP-ecm", "fsl,ecm" where - CHIP is the processor (mpc8572, mpc8544, etc.) - - - reg - Usage: required - Value type: <prop-encoded-array> - Definition: A standard property. The value specifies the - physical address offset and length of the CCSR space - registers. - - - interrupts - Usage: required - Value type: <prop-encoded-array> - - - interrupt-parent - Usage: required - Value type: <phandle> - -===================================================================== diff --git a/Documentation/powerpc/dts-bindings/eeprom.txt b/Documentation/powerpc/dts-bindings/eeprom.txt deleted file mode 100644 index 4342c10de1b..00000000000 --- a/Documentation/powerpc/dts-bindings/eeprom.txt +++ /dev/null @@ -1,28 +0,0 @@ -EEPROMs (I2C) - -Required properties: - - - compatible : should be "<manufacturer>,<type>" - If there is no specific driver for <manufacturer>, a generic - driver based on <type> is selected. Possible types are: - 24c00, 24c01, 24c02, 24c04, 24c08, 24c16, 24c32, 24c64, - 24c128, 24c256, 24c512, 24c1024, spd - - - reg : the I2C address of the EEPROM - -Optional properties: - - - pagesize : the length of the pagesize for writing. Please consult the - manual of your device, that value varies a lot. A wrong value - may result in data loss! If not specified, a safety value of - '1' is used which will be very slow. - - - read-only: this parameterless property disables writes to the eeprom - -Example: - -eeprom@52 { - compatible = "atmel,24c32"; - reg = <0x52>; - pagesize = <32>; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt b/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt deleted file mode 100644 index 35a46536240..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt +++ /dev/null @@ -1,40 +0,0 @@ -* Freescale 83xx and 512x PCI bridges - -Freescale 83xx and 512x SOCs include the same pci bridge core. - -83xx/512x specific notes: -- reg: should contain two address length tuples - The first is for the internal pci bridge registers - The second is for the pci config space access registers - -Example (MPC8313ERDB) - pci0: pci@e0008500 { - cell-index = <1>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = < - /* IDSEL 0x0E -mini PCI */ - 0x7000 0x0 0x0 0x1 &ipic 18 0x8 - 0x7000 0x0 0x0 0x2 &ipic 18 0x8 - 0x7000 0x0 0x0 0x3 &ipic 18 0x8 - 0x7000 0x0 0x0 0x4 &ipic 18 0x8 - - /* IDSEL 0x0F - PCI slot */ - 0x7800 0x0 0x0 0x1 &ipic 17 0x8 - 0x7800 0x0 0x0 0x2 &ipic 18 0x8 - 0x7800 0x0 0x0 0x3 &ipic 17 0x8 - 0x7800 0x0 0x0 0x4 &ipic 18 0x8>; - interrupt-parent = <&ipic>; - interrupts = <66 0x8>; - bus-range = <0x0 0x0>; - ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 - 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 - 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; - clock-frequency = <66666666>; - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - reg = <0xe0008500 0x100 /* internal registers */ - 0xe0008300 0x8>; /* config space access registers */ - compatible = "fsl,mpc8349-pci"; - device_type = "pci"; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt b/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt deleted file mode 100644 index b0019eb5330..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt +++ /dev/null @@ -1,60 +0,0 @@ -GPIO controllers on MPC8xxx SoCs - -This is for the non-QE/CPM/GUTs GPIO controllers as found on -8349, 8572, 8610 and compatible. - -Every GPIO controller node must have #gpio-cells property defined, -this information will be used to translate gpio-specifiers. - -Required properties: -- compatible : "fsl,<CHIP>-gpio" followed by "fsl,mpc8349-gpio" for - 83xx, "fsl,mpc8572-gpio" for 85xx and "fsl,mpc8610-gpio" for 86xx. -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). - - interrupts : Interrupt mapping for GPIO IRQ. - - interrupt-parent : Phandle for the interrupt controller that - services interrupts for this device. -- gpio-controller : Marks the port as GPIO controller. - -Example of gpio-controller nodes for a MPC8347 SoC: - - gpio1: gpio-controller@c00 { - #gpio-cells = <2>; - compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; - reg = <0xc00 0x100>; - interrupts = <74 0x8>; - interrupt-parent = <&ipic>; - gpio-controller; - }; - - gpio2: gpio-controller@d00 { - #gpio-cells = <2>; - compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; - reg = <0xd00 0x100>; - interrupts = <75 0x8>; - interrupt-parent = <&ipic>; - gpio-controller; - }; - -See booting-without-of.txt for details of how to specify GPIO -information for devices. - -To use GPIO pins as interrupt sources for peripherals, specify the -GPIO controller as the interrupt parent and define GPIO number + -trigger mode using the interrupts property, which is defined like -this: - -interrupts = <number trigger>, where: - - number: GPIO pin (0..31) - - trigger: trigger mode: - 2 = trigger on falling edge - 3 = trigger on both edges - -Example of device using this is: - - funkyfpga@0 { - compatible = "funky-fpga"; - ... - interrupts = <4 3>; - interrupt-parent = <&gpio1>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt deleted file mode 100644 index 39e941515a3..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/board.txt +++ /dev/null @@ -1,63 +0,0 @@ -* Board Control and Status (BCSR) - -Required properties: - - - compatible : Should be "fsl,<board>-bcsr" - - reg : Offset and length of the register set for the device - -Example: - - bcsr@f8000000 { - compatible = "fsl,mpc8360mds-bcsr"; - reg = <f8000000 8000>; - }; - -* Freescale on board FPGA - -This is the memory-mapped registers for on board FPGA. - -Required properities: -- compatible : should be "fsl,fpga-pixis". -- reg : should contain the address and the length of the FPPGA register - set. -- interrupt-parent: should specify phandle for the interrupt controller. -- interrupts : should specify event (wakeup) IRQ. - -Example (MPC8610HPCD): - - board-control@e8000000 { - compatible = "fsl,fpga-pixis"; - reg = <0xe8000000 32>; - interrupt-parent = <&mpic>; - interrupts = <8 8>; - }; - -* Freescale BCSR GPIO banks - -Some BCSR registers act as simple GPIO controllers, each such -register can be represented by the gpio-controller node. - -Required properities: -- compatible : Should be "fsl,<board>-bcsr-gpio". -- reg : Should contain the address and the length of the GPIO bank - register. -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). -- gpio-controller : Marks the port as GPIO controller. - -Example: - - bcsr@1,0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8360mds-bcsr"; - reg = <1 0 0x8000>; - ranges = <0 1 0 0x8000>; - - bcsr13: gpio-controller@d { - #gpio-cells = <2>; - compatible = "fsl,mpc8360mds-bcsr-gpio"; - reg = <0xd 1>; - gpio-controller; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/can.txt b/Documentation/powerpc/dts-bindings/fsl/can.txt deleted file mode 100644 index 2fa4fcd38fd..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/can.txt +++ /dev/null @@ -1,53 +0,0 @@ -CAN Device Tree Bindings ------------------------- - -(c) 2006-2009 Secret Lab Technologies Ltd -Grant Likely <grant.likely@secretlab.ca> - -fsl,mpc5200-mscan nodes ------------------------ -In addition to the required compatible-, reg- and interrupt-properties, you can -also specify which clock source shall be used for the controller: - -- fsl,mscan-clock-source : a string describing the clock source. Valid values - are: "ip" for ip bus clock - "ref" for reference clock (XTAL) - "ref" is default in case this property is not - present. - -fsl,mpc5121-mscan nodes ------------------------ -In addition to the required compatible-, reg- and interrupt-properties, you can -also specify which clock source and divider shall be used for the controller: - -- fsl,mscan-clock-source : a string describing the clock source. Valid values - are: "ip" for ip bus clock - "ref" for reference clock - "sys" for system clock - If this property is not present, an optimal CAN - clock source and frequency based on the system - clock will be selected. If this is not possible, - the reference clock will be used. - -- fsl,mscan-clock-divider: for the reference and system clock, an additional - clock divider can be specified. By default, a - value of 1 is used. - -Note that the MPC5121 Rev. 1 processor is not supported. - -Examples: - can@1300 { - compatible = "fsl,mpc5121-mscan"; - interrupts = <12 0x8>; - interrupt-parent = <&ipic>; - reg = <0x1300 0x80>; - }; - - can@1380 { - compatible = "fsl,mpc5121-mscan"; - interrupts = <13 0x8>; - interrupt-parent = <&ipic>; - reg = <0x1380 0x80>; - fsl,mscan-clock-source = "ref"; - fsl,mscan-clock-divider = <3>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt deleted file mode 100644 index 160c752484b..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt +++ /dev/null @@ -1,67 +0,0 @@ -* Freescale Communications Processor Module - -NOTE: This is an interim binding, and will likely change slightly, -as more devices are supported. The QE bindings especially are -incomplete. - -* Root CPM node - -Properties: -- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe". -- reg : A 48-byte region beginning with CPCR. - -Example: - cpm@119c0 { - #address-cells = <1>; - #size-cells = <1>; - #interrupt-cells = <2>; - compatible = "fsl,mpc8272-cpm", "fsl,cpm2"; - reg = <119c0 30>; - } - -* Properties common to multiple CPM/QE devices - -- fsl,cpm-command : This value is ORed with the opcode and command flag - to specify the device on which a CPM command operates. - -- fsl,cpm-brg : Indicates which baud rate generator the device - is associated with. If absent, an unused BRG - should be dynamically allocated. If zero, the - device uses an external clock rather than a BRG. - -- reg : Unless otherwise specified, the first resource represents the - scc/fcc/ucc registers, and the second represents the device's - parameter RAM region (if it has one). - -* Multi-User RAM (MURAM) - -The multi-user/dual-ported RAM is expressed as a bus under the CPM node. - -Ranges must be set up subject to the following restrictions: - -- Children's reg nodes must be offsets from the start of all muram, even - if the user-data area does not begin at zero. -- If multiple range entries are used, the difference between the parent - address and the child address must be the same in all, so that a single - mapping can cover them all while maintaining the ability to determine - CPM-side offsets with pointer subtraction. It is recommended that - multiple range entries not be used. -- A child address of zero must be translatable, even if no reg resources - contain it. - -A child "data" node must exist, compatible with "fsl,cpm-muram-data", to -indicate the portion of muram that is usable by the OS for arbitrary -purposes. The data node may have an arbitrary number of reg resources, -all of which contribute to the allocatable muram pool. - -Example, based on mpc8272: - muram@0 { - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 10000>; - - data@0 { - compatible = "fsl,cpm-muram-data"; - reg = <0 2000 9800 800>; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt deleted file mode 100644 index 4c7d45eaf02..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt +++ /dev/null @@ -1,21 +0,0 @@ -* Baud Rate Generators - -Currently defined compatibles: -fsl,cpm-brg -fsl,cpm1-brg -fsl,cpm2-brg - -Properties: -- reg : There may be an arbitrary number of reg resources; BRG - numbers are assigned to these in order. -- clock-frequency : Specifies the base frequency driving - the BRG. - -Example: - brg@119f0 { - compatible = "fsl,mpc8272-brg", - "fsl,cpm2-brg", - "fsl,cpm-brg"; - reg = <119f0 10 115f0 10>; - clock-frequency = <d#25000000>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt deleted file mode 100644 index 87bc6048667..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt +++ /dev/null @@ -1,41 +0,0 @@ -* I2C - -The I2C controller is expressed as a bus under the CPM node. - -Properties: -- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c" -- reg : On CPM2 devices, the second resource doesn't specify the I2C - Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM - (typically 0x8afc 0x2). -- #address-cells : Should be one. The cell is the i2c device address with - the r/w bit set to zero. -- #size-cells : Should be zero. -- clock-frequency : Can be used to set the i2c clock frequency. If - unspecified, a default frequency of 60kHz is being used. -The following two properties are deprecated. They are only used by legacy -i2c drivers to find the bus to probe: -- linux,i2c-index : Can be used to hard code an i2c bus number. By default, - the bus number is dynamically assigned by the i2c core. -- linux,i2c-class : Can be used to override the i2c class. The class is used - by legacy i2c device drivers to find a bus in a specific context like - system management, video or sound. By default, I2C_CLASS_HWMON (1) is - being used. The definition of the classes can be found in - include/i2c/i2c.h - -Example, based on mpc823: - - i2c@860 { - compatible = "fsl,mpc823-i2c", - "fsl,cpm1-i2c"; - reg = <0x860 0x20 0x3c80 0x30>; - interrupts = <16>; - interrupt-parent = <&CPM_PIC>; - fsl,cpm-command = <0x10>; - #address-cells = <1>; - #size-cells = <0>; - - rtc@68 { - compatible = "dallas,ds1307"; - reg = <0x68>; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt deleted file mode 100644 index 8e3ee168161..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt +++ /dev/null @@ -1,18 +0,0 @@ -* Interrupt Controllers - -Currently defined compatibles: -- fsl,cpm1-pic - - only one interrupt cell -- fsl,pq1-pic -- fsl,cpm2-pic - - second interrupt cell is level/sense: - - 2 is falling edge - - 8 is active low - -Example: - interrupt-controller@10c00 { - #interrupt-cells = <2>; - interrupt-controller; - reg = <10c00 80>; - compatible = "mpc8272-pic", "fsl,cpm2-pic"; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt deleted file mode 100644 index 74bfda4bb82..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt +++ /dev/null @@ -1,15 +0,0 @@ -* USB (Universal Serial Bus Controller) - -Properties: -- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb" - -Example: - usb@11bc0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,cpm2-usb"; - reg = <11b60 18 8b00 100>; - interrupts = <b 8>; - interrupt-parent = <&PIC>; - fsl,cpm-command = <2e600000>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/gpio.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/gpio.txt deleted file mode 100644 index 349f79fd707..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/gpio.txt +++ /dev/null @@ -1,38 +0,0 @@ -Every GPIO controller node must have #gpio-cells property defined, -this information will be used to translate gpio-specifiers. - -On CPM1 devices, all ports are using slightly different register layouts. -Ports A, C and D are 16bit ports and Ports B and E are 32bit ports. - -On CPM2 devices, all ports are 32bit ports and use a common register layout. - -Required properties: -- compatible : "fsl,cpm1-pario-bank-a", "fsl,cpm1-pario-bank-b", - "fsl,cpm1-pario-bank-c", "fsl,cpm1-pario-bank-d", - "fsl,cpm1-pario-bank-e", "fsl,cpm2-pario-bank" -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). -- gpio-controller : Marks the port as GPIO controller. - -Example of three SOC GPIO banks defined as gpio-controller nodes: - - CPM1_PIO_A: gpio-controller@950 { - #gpio-cells = <2>; - compatible = "fsl,cpm1-pario-bank-a"; - reg = <0x950 0x10>; - gpio-controller; - }; - - CPM1_PIO_B: gpio-controller@ab8 { - #gpio-cells = <2>; - compatible = "fsl,cpm1-pario-bank-b"; - reg = <0xab8 0x10>; - gpio-controller; - }; - - CPM1_PIO_E: gpio-controller@ac8 { - #gpio-cells = <2>; - compatible = "fsl,cpm1-pario-bank-e"; - reg = <0xac8 0x18>; - gpio-controller; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt deleted file mode 100644 index 0e426944658..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt +++ /dev/null @@ -1,45 +0,0 @@ -* Network - -Currently defined compatibles: -- fsl,cpm1-scc-enet -- fsl,cpm2-scc-enet -- fsl,cpm1-fec-enet -- fsl,cpm2-fcc-enet (third resource is GFEMR) -- fsl,qe-enet - -Example: - - ethernet@11300 { - device_type = "network"; - compatible = "fsl,mpc8272-fcc-enet", - "fsl,cpm2-fcc-enet"; - reg = <11300 20 8400 100 11390 1>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <20 8>; - interrupt-parent = <&PIC>; - phy-handle = <&PHY0>; - fsl,cpm-command = <12000300>; - }; - -* MDIO - -Currently defined compatibles: -fsl,pq1-fec-mdio (reg is same as first resource of FEC device) -fsl,cpm2-mdio-bitbang (reg is port C registers) - -Properties for fsl,cpm2-mdio-bitbang: -fsl,mdio-pin : pin of port C controlling mdio data -fsl,mdc-pin : pin of port C controlling mdio clock - -Example: - mdio@10d40 { - device_type = "mdio"; - compatible = "fsl,mpc8272ads-mdio-bitbang", - "fsl,mpc8272-mdio-bitbang", - "fsl,cpm2-mdio-bitbang"; - reg = <10d40 14>; - #address-cells = <1>; - #size-cells = <0>; - fsl,mdio-pin = <12>; - fsl,mdc-pin = <13>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt deleted file mode 100644 index 4f8930263dd..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt +++ /dev/null @@ -1,115 +0,0 @@ -* Freescale QUICC Engine module (QE) -This represents qe module that is installed on PowerQUICC II Pro. - -NOTE: This is an interim binding; it should be updated to fit -in with the CPM binding later in this document. - -Basically, it is a bus of devices, that could act more or less -as a complete entity (UCC, USB etc ). All of them should be siblings on -the "root" qe node, using the common properties from there. -The description below applies to the qe of MPC8360 and -more nodes and properties would be extended in the future. - -i) Root QE device - -Required properties: -- compatible : should be "fsl,qe"; -- model : precise model of the QE, Can be "QE", "CPM", or "CPM2" -- reg : offset and length of the device registers. -- bus-frequency : the clock frequency for QUICC Engine. -- fsl,qe-num-riscs: define how many RISC engines the QE has. -- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the - threads. - -Optional properties: -- fsl,firmware-phandle: - Usage: required only if there is no fsl,qe-firmware child node - Value type: <phandle> - Definition: Points to a firmware node (see "QE Firmware Node" below) - that contains the firmware that should be uploaded for this QE. - The compatible property for the firmware node should say, - "fsl,qe-firmware". - -Recommended properties -- brg-frequency : the internal clock source frequency for baud-rate - generators in Hz. - -Example: - qe@e0100000 { - #address-cells = <1>; - #size-cells = <1>; - #interrupt-cells = <2>; - compatible = "fsl,qe"; - ranges = <0 e0100000 00100000>; - reg = <e0100000 480>; - brg-frequency = <0>; - bus-frequency = <179A7B00>; - } - -* Multi-User RAM (MURAM) - -Required properties: -- compatible : should be "fsl,qe-muram", "fsl,cpm-muram". -- mode : the could be "host" or "slave". -- ranges : Should be defined as specified in 1) to describe the - translation of MURAM addresses. -- data-only : sub-node which defines the address area under MURAM - bus that can be allocated as data/parameter - -Example: - - muram@10000 { - compatible = "fsl,qe-muram", "fsl,cpm-muram"; - ranges = <0 00010000 0000c000>; - - data-only@0{ - compatible = "fsl,qe-muram-data", - "fsl,cpm-muram-data"; - reg = <0 c000>; - }; - }; - -* QE Firmware Node - -This node defines a firmware binary that is embedded in the device tree, for -the purpose of passing the firmware from bootloader to the kernel, or from -the hypervisor to the guest. - -The firmware node itself contains the firmware binary contents, a compatible -property, and any firmware-specific properties. The node should be placed -inside a QE node that needs it. Doing so eliminates the need for a -fsl,firmware-phandle property. Other QE nodes that need the same firmware -should define an fsl,firmware-phandle property that points to the firmware node -in the first QE node. - -The fsl,firmware property can be specified in the DTS (possibly using incbin) -or can be inserted by the boot loader at boot time. - -Required properties: - - compatible - Usage: required - Value type: <string> - Definition: A standard property. Specify a string that indicates what - kind of firmware it is. For QE, this should be "fsl,qe-firmware". - - - fsl,firmware - Usage: required - Value type: <prop-encoded-array>, encoded as an array of bytes - Definition: A standard property. This property contains the firmware - binary "blob". - -Example: - qe1@e0080000 { - compatible = "fsl,qe"; - qe_firmware:qe-firmware { - compatible = "fsl,qe-firmware"; - fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...]; - }; - ... - }; - - qe2@e0090000 { - compatible = "fsl,qe"; - fsl,firmware-phandle = <&qe_firmware>; - ... - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt deleted file mode 100644 index 249db3a15d1..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt +++ /dev/null @@ -1,24 +0,0 @@ -* Uploaded QE firmware - - If a new firmware has been uploaded to the QE (usually by the - boot loader), then a 'firmware' child node should be added to the QE - node. This node provides information on the uploaded firmware that - device drivers may need. - - Required properties: - - id: The string name of the firmware. This is taken from the 'id' - member of the qe_firmware structure of the uploaded firmware. - Device drivers can search this string to determine if the - firmware they want is already present. - - extended-modes: The Extended Modes bitfield, taken from the - firmware binary. It is a 64-bit number represented - as an array of two 32-bit numbers. - - virtual-traps: The virtual traps, taken from the firmware binary. - It is an array of 8 32-bit numbers. - -Example: - firmware { - id = "Soft-UART"; - extended-modes = <0 0>; - virtual-traps = <0 0 0 0 0 0 0 0>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt deleted file mode 100644 index 60984260207..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt +++ /dev/null @@ -1,51 +0,0 @@ -* Parallel I/O Ports - -This node configures Parallel I/O ports for CPUs with QE support. -The node should reside in the "soc" node of the tree. For each -device that using parallel I/O ports, a child node should be created. -See the definition of the Pin configuration nodes below for more -information. - -Required properties: -- device_type : should be "par_io". -- reg : offset to the register set and its length. -- num-ports : number of Parallel I/O ports - -Example: -par_io@1400 { - reg = <1400 100>; - #address-cells = <1>; - #size-cells = <0>; - device_type = "par_io"; - num-ports = <7>; - ucc_pin@01 { - ...... - }; - -Note that "par_io" nodes are obsolete, and should not be used for -the new device trees. Instead, each Par I/O bank should be represented -via its own gpio-controller node: - -Required properties: -- #gpio-cells : should be "2". -- compatible : should be "fsl,<chip>-qe-pario-bank", - "fsl,mpc8323-qe-pario-bank". -- reg : offset to the register set and its length. -- gpio-controller : node to identify gpio controllers. - -Example: - qe_pio_a: gpio-controller@1400 { - #gpio-cells = <2>; - compatible = "fsl,mpc8360-qe-pario-bank", - "fsl,mpc8323-qe-pario-bank"; - reg = <0x1400 0x18>; - gpio-controller; - }; - - qe_pio_e: gpio-controller@1460 { - #gpio-cells = <2>; - compatible = "fsl,mpc8360-qe-pario-bank", - "fsl,mpc8323-qe-pario-bank"; - reg = <0x1460 0x18>; - gpio-controller; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt deleted file mode 100644 index c5b43061db3..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt +++ /dev/null @@ -1,60 +0,0 @@ -* Pin configuration nodes - -Required properties: -- linux,phandle : phandle of this node; likely referenced by a QE - device. -- pio-map : array of pin configurations. Each pin is defined by 6 - integers. The six numbers are respectively: port, pin, dir, - open_drain, assignment, has_irq. - - port : port number of the pin; 0-6 represent port A-G in UM. - - pin : pin number in the port. - - dir : direction of the pin, should encode as follows: - - 0 = The pin is disabled - 1 = The pin is an output - 2 = The pin is an input - 3 = The pin is I/O - - - open_drain : indicates the pin is normal or wired-OR: - - 0 = The pin is actively driven as an output - 1 = The pin is an open-drain driver. As an output, the pin is - driven active-low, otherwise it is three-stated. - - - assignment : function number of the pin according to the Pin Assignment - tables in User Manual. Each pin can have up to 4 possible functions in - QE and two options for CPM. - - has_irq : indicates if the pin is used as source of external - interrupts. - -Example: - ucc_pin@01 { - linux,phandle = <140001>; - pio-map = < - /* port pin dir open_drain assignment has_irq */ - 0 3 1 0 1 0 /* TxD0 */ - 0 4 1 0 1 0 /* TxD1 */ - 0 5 1 0 1 0 /* TxD2 */ - 0 6 1 0 1 0 /* TxD3 */ - 1 6 1 0 3 0 /* TxD4 */ - 1 7 1 0 1 0 /* TxD5 */ - 1 9 1 0 2 0 /* TxD6 */ - 1 a 1 0 2 0 /* TxD7 */ - 0 9 2 0 1 0 /* RxD0 */ - 0 a 2 0 1 0 /* RxD1 */ - 0 b 2 0 1 0 /* RxD2 */ - 0 c 2 0 1 0 /* RxD3 */ - 0 d 2 0 1 0 /* RxD4 */ - 1 1 2 0 2 0 /* RxD5 */ - 1 0 2 0 2 0 /* RxD6 */ - 1 4 2 0 2 0 /* RxD7 */ - 0 7 1 0 1 0 /* TX_EN */ - 0 8 1 0 1 0 /* TX_ER */ - 0 f 2 0 1 0 /* RX_DV */ - 0 10 2 0 1 0 /* RX_ER */ - 0 0 2 0 1 0 /* RX_CLK */ - 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ - 2 8 2 0 1 0>; /* GTX125 - CLK9 */ - }; - - diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt deleted file mode 100644 index e47734bee3f..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt +++ /dev/null @@ -1,70 +0,0 @@ -* UCC (Unified Communications Controllers) - -Required properties: -- device_type : should be "network", "hldc", "uart", "transparent" - "bisync", "atm", or "serial". -- compatible : could be "ucc_geth" or "fsl_atm" and so on. -- cell-index : the ucc number(1-8), corresponding to UCCx in UM. -- reg : Offset and length of the register set for the device -- interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. -- interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. -- pio-handle : The phandle for the Parallel I/O port configuration. -- port-number : for UART drivers, the port number to use, between 0 and 3. - This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0. - The port number is added to the minor number of the device. Unlike the - CPM UART driver, the port-number is required for the QE UART driver. -- soft-uart : for UART drivers, if specified this means the QE UART device - driver should use "Soft-UART" mode, which is needed on some SOCs that have - broken UART hardware. Soft-UART is provided via a microcode upload. -- rx-clock-name: the UCC receive clock source - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively -- tx-clock-name: the UCC transmit clock source - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively -The following two properties are deprecated. rx-clock has been replaced -with rx-clock-name, and tx-clock has been replaced with tx-clock-name. -Drivers that currently use the deprecated properties should continue to -do so, in order to support older device trees, but they should be updated -to check for the new properties first. -- rx-clock : represents the UCC receive clock source. - 0x00 : clock source is disabled; - 0x1~0x10 : clock source is BRG1~BRG16 respectively; - 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. -- tx-clock: represents the UCC transmit clock source; - 0x00 : clock source is disabled; - 0x1~0x10 : clock source is BRG1~BRG16 respectively; - 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. - -Required properties for network device_type: -- mac-address : list of bytes representing the ethernet address. -- phy-handle : The phandle for the PHY connected to this controller. - -Recommended properties: -- phy-connection-type : a string naming the controller/PHY interface type, - i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal - Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), - "tbi", or "rtbi". - -Example: - ucc@2000 { - device_type = "network"; - compatible = "ucc_geth"; - cell-index = <1>; - reg = <2000 200>; - interrupts = <a0 0>; - interrupt-parent = <700>; - mac-address = [ 00 04 9f 00 23 23 ]; - rx-clock = "none"; - tx-clock = "clk9"; - phy-handle = <212000>; - phy-connection-type = "gmii"; - pio-handle = <140001>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt deleted file mode 100644 index 9ccd5f30405..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt +++ /dev/null @@ -1,37 +0,0 @@ -Freescale QUICC Engine USB Controller - -Required properties: -- compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb". -- reg : the first two cells should contain usb registers location and - length, the next two two cells should contain PRAM location and - length. -- interrupts : should contain USB interrupt. -- interrupt-parent : interrupt source phandle. -- fsl,fullspeed-clock : specifies the full speed USB clock source: - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively -- fsl,lowspeed-clock : specifies the low speed USB clock source: - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively -- hub-power-budget : USB power budget for the root hub, in mA. -- gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP, - USBRN, SPEED (optional), and POWER (optional). - -Example: - -usb@6c0 { - compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb"; - reg = <0x6c0 0x40 0x8b00 0x100>; - interrupts = <11>; - interrupt-parent = <&qeic>; - fsl,fullspeed-clock = "clk21"; - gpios = <&qe_pio_b 2 0 /* USBOE */ - &qe_pio_b 3 0 /* USBTP */ - &qe_pio_b 8 0 /* USBTN */ - &qe_pio_b 9 0 /* USBRP */ - &qe_pio_b 11 0 /* USBRN */ - &qe_pio_e 20 0 /* SPEED */ - &qe_pio_e 21 0 /* POWER */>; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt deleted file mode 100644 index 2ea76d9d137..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt +++ /dev/null @@ -1,32 +0,0 @@ -* Serial - -Currently defined compatibles: -- fsl,cpm1-smc-uart -- fsl,cpm2-smc-uart -- fsl,cpm1-scc-uart -- fsl,cpm2-scc-uart -- fsl,qe-uart - -Modem control lines connected to GPIO controllers are listed in the gpios -property as described in booting-without-of.txt, section IX.1 in the following -order: - -CTS, RTS, DCD, DSR, DTR, and RI. - -The gpios property is optional and can be left out when control lines are -not used. - -Example: - - serial@11a00 { - device_type = "serial"; - compatible = "fsl,mpc8272-scc-uart", - "fsl,cpm2-scc-uart"; - reg = <11a00 20 8000 100>; - interrupts = <28 8>; - interrupt-parent = <&PIC>; - fsl,cpm-brg = <1>; - fsl,cpm-command = <00800000>; - gpios = <&gpio_c 15 0 - &gpio_d 29 0>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/diu.txt b/Documentation/powerpc/dts-bindings/fsl/diu.txt deleted file mode 100644 index b66cb6d31d6..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/diu.txt +++ /dev/null @@ -1,34 +0,0 @@ -* Freescale Display Interface Unit - -The Freescale DIU is a LCD controller, with proper hardware, it can also -drive DVI monitors. - -Required properties: -- compatible : should be "fsl,diu" or "fsl,mpc5121-diu". -- reg : should contain at least address and length of the DIU register - set. -- interrupts : one DIU interrupt should be described here. -- interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Optional properties: -- edid : verbatim EDID data block describing attached display. - Data from the detailed timing descriptor will be used to - program the display controller. - -Example (MPC8610HPCD): - display@2c000 { - compatible = "fsl,diu"; - reg = <0x2c000 100>; - interrupts = <72 2>; - interrupt-parent = <&mpic>; - }; - -Example for MPC5121: - display@2100 { - compatible = "fsl,mpc5121-diu"; - reg = <0x2100 0x100>; - interrupts = <64 0x8>; - interrupt-parent = <&ipic>; - edid = [edid-data]; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/dma.txt b/Documentation/powerpc/dts-bindings/fsl/dma.txt deleted file mode 100644 index 2a4b4bce611..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/dma.txt +++ /dev/null @@ -1,144 +0,0 @@ -* Freescale 83xx DMA Controller - -Freescale PowerPC 83xx have on chip general purpose DMA controllers. - -Required properties: - -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8349, mpc8360, etc.) and the second is - "fsl,elo-dma" -- reg : <registers mapping for DMA general status reg> -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. -- cell-index : controller index. 0 for controller @ 0x8100 -- interrupts : <interrupt mapping for DMA IRQ> -- interrupt-parent : optional, if needed for interrupt mapping - - -- DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8349, mpc8350, etc.) and the second is - "fsl,elo-dma-channel". However, see note below. - - reg : <registers mapping for channel> - - cell-index : dma channel index starts at 0. - -Optional properties: - - interrupts : <interrupt mapping for DMA channel IRQ> - (on 83xx this is expected to be identical to - the interrupts property of the parent node) - - interrupt-parent : optional, if needed for interrupt mapping - -Example: - dma@82a8 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8349-dma", "fsl,elo-dma"; - reg = <0x82a8 4>; - ranges = <0 0x8100 0x1a4>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - cell-index = <0>; - dma-channel@0 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <0>; - reg = <0 0x80>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - }; - dma-channel@80 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <1>; - reg = <0x80 0x80>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - }; - dma-channel@100 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <2>; - reg = <0x100 0x80>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - }; - dma-channel@180 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <3>; - reg = <0x180 0x80>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - }; - }; - -* Freescale 85xx/86xx DMA Controller - -Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. - -Required properties: - -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8540, mpc8540, etc.) and the second is - "fsl,eloplus-dma" -- reg : <registers mapping for DMA general status reg> -- cell-index : controller index. 0 for controller @ 0x21000, - 1 for controller @ 0xc000 -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. - -- DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8540, mpc8560, etc.) and the second is - "fsl,eloplus-dma-channel". However, see note below. - - cell-index : dma channel index starts at 0. - - reg : <registers mapping for channel> - - interrupts : <interrupt mapping for DMA channel IRQ> - - interrupt-parent : optional, if needed for interrupt mapping - -Example: - dma@21300 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma"; - reg = <0x21300 4>; - ranges = <0 0x21100 0x200>; - cell-index = <0>; - dma-channel@0 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0 0x80>; - cell-index = <0>; - interrupt-parent = <&mpic>; - interrupts = <20 2>; - }; - dma-channel@80 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0x80 0x80>; - cell-index = <1>; - interrupt-parent = <&mpic>; - interrupts = <21 2>; - }; - dma-channel@100 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0x100 0x80>; - cell-index = <2>; - interrupt-parent = <&mpic>; - interrupts = <22 2>; - }; - dma-channel@180 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0x180 0x80>; - cell-index = <3>; - interrupt-parent = <&mpic>; - interrupts = <23 2>; - }; - }; - -Note on DMA channel compatible properties: The compatible property must say -"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA -driver (fsldma). Any DMA channel used by fsldma cannot be used by another -DMA driver, such as the SSI sound drivers for the MPC8610. Therefore, any DMA -channel that should be used for another driver should not use -"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel". For the SSI drivers, for -example, the compatible property should be "fsl,ssi-dma-channel". See ssi.txt -for more information. diff --git a/Documentation/powerpc/dts-bindings/fsl/esdhc.txt b/Documentation/powerpc/dts-bindings/fsl/esdhc.txt deleted file mode 100644 index 64bcb8be973..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/esdhc.txt +++ /dev/null @@ -1,29 +0,0 @@ -* Freescale Enhanced Secure Digital Host Controller (eSDHC) - -The Enhanced Secure Digital Host Controller provides an interface -for MMC, SD, and SDIO types of memory cards. - -Required properties: - - compatible : should be - "fsl,<chip>-esdhc", "fsl,esdhc" - - reg : should contain eSDHC registers location and length. - - interrupts : should contain eSDHC interrupt. - - interrupt-parent : interrupt source phandle. - - clock-frequency : specifies eSDHC base clock frequency. - - sdhci,wp-inverted : (optional) specifies that eSDHC controller - reports inverted write-protect state; - - sdhci,1-bit-only : (optional) specifies that a controller can - only handle 1-bit data transfers. - - sdhci,auto-cmd12: (optional) specifies that a controller can - only handle auto CMD12. - -Example: - -sdhci@2e000 { - compatible = "fsl,mpc8378-esdhc", "fsl,esdhc"; - reg = <0x2e000 0x1000>; - interrupts = <42 0x8>; - interrupt-parent = <&ipic>; - /* Filled in by U-Boot */ - clock-frequency = <0>; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/gtm.txt b/Documentation/powerpc/dts-bindings/fsl/gtm.txt deleted file mode 100644 index 9a33efded4b..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/gtm.txt +++ /dev/null @@ -1,31 +0,0 @@ -* Freescale General-purpose Timers Module - -Required properties: - - compatible : should be - "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs - "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs - "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs - - reg : should contain gtm registers location and length (0x40). - - interrupts : should contain four interrupts. - - interrupt-parent : interrupt source phandle. - - clock-frequency : specifies the frequency driving the timer. - -Example: - -timer@500 { - compatible = "fsl,mpc8360-gtm", "fsl,gtm"; - reg = <0x500 0x40>; - interrupts = <90 8 78 8 84 8 72 8>; - interrupt-parent = <&ipic>; - /* filled by u-boot */ - clock-frequency = <0>; -}; - -timer@440 { - compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; - reg = <0x440 0x40>; - interrupts = <12 13 14 15>; - interrupt-parent = <&qeic>; - /* filled by u-boot */ - clock-frequency = <0>; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/guts.txt b/Documentation/powerpc/dts-bindings/fsl/guts.txt deleted file mode 100644 index 9e7a2417dac..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/guts.txt +++ /dev/null @@ -1,25 +0,0 @@ -* Global Utilities Block - -The global utilities block controls power management, I/O device -enabling, power-on-reset configuration monitoring, general-purpose -I/O signal configuration, alternate function selection for multiplexed -signals, and clock control. - -Required properties: - - - compatible : Should define the compatible device type for - global-utilities. - - reg : Offset and length of the register set for the device. - -Recommended properties: - - - fsl,has-rstcr : Indicates that the global utilities register set - contains a functioning "reset control register" (i.e. the board - is wired to reset upon setting the HRESET_REQ bit in this register). - -Example: - global-utilities@e0000 { /* global utilities block */ - compatible = "fsl,mpc8548-guts"; - reg = <e0000 1000>; - fsl,has-rstcr; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt deleted file mode 100644 index 1eacd6b20ed..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/i2c.txt +++ /dev/null @@ -1,64 +0,0 @@ -* I2C - -Required properties : - - - reg : Offset and length of the register set for the device - - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a - compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121, - mpc5200 or mpc5200b. For the mpc5121, an additional node - "fsl,mpc5121-i2c-ctrl" is required as shown in the example below. - -Recommended properties : - - - interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - fsl,preserve-clocking : boolean; if defined, the clock settings - from the bootloader are preserved (not touched). - - clock-frequency : desired I2C bus clock frequency in Hz. - - fsl,timeout : I2C bus timeout in microseconds. - -Examples : - - /* MPC5121 based board */ - i2c@1740 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5121-i2c", "fsl-i2c"; - reg = <0x1740 0x20>; - interrupts = <11 0x8>; - interrupt-parent = <&ipic>; - clock-frequency = <100000>; - }; - - i2ccontrol@1760 { - compatible = "fsl,mpc5121-i2c-ctrl"; - reg = <0x1760 0x8>; - }; - - /* MPC5200B based board */ - i2c@3d00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d00 0x40>; - interrupts = <2 15 0>; - interrupt-parent = <&mpc5200_pic>; - fsl,preserve-clocking; - }; - - /* MPC8544 base board */ - i2c@3100 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc8544-i2c", "fsl-i2c"; - reg = <0x3100 0x100>; - interrupts = <43 2>; - interrupt-parent = <&mpic>; - clock-frequency = <400000>; - fsl,timeout = <10000>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/lbc.txt b/Documentation/powerpc/dts-bindings/fsl/lbc.txt deleted file mode 100644 index 3300fec501c..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/lbc.txt +++ /dev/null @@ -1,35 +0,0 @@ -* Chipselect/Local Bus - -Properties: -- name : Should be localbus -- #address-cells : Should be either two or three. The first cell is the - chipselect number, and the remaining cells are the - offset into the chipselect. -- #size-cells : Either one or two, depending on how large each chipselect - can be. -- ranges : Each range corresponds to a single chipselect, and cover - the entire access window as configured. - -Example: - localbus@f0010100 { - compatible = "fsl,mpc8272-localbus", - "fsl,pq2-localbus"; - #address-cells = <2>; - #size-cells = <1>; - reg = <f0010100 40>; - - ranges = <0 0 fe000000 02000000 - 1 0 f4500000 00008000>; - - flash@0,0 { - compatible = "jedec-flash"; - reg = <0 0 2000000>; - bank-width = <4>; - device-width = <1>; - }; - - board-control@1,0 { - reg = <1 0 20>; - compatible = "fsl,mpc8272ads-bcsr"; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/mcm.txt b/Documentation/powerpc/dts-bindings/fsl/mcm.txt deleted file mode 100644 index 4ceda9b3b41..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mcm.txt +++ /dev/null @@ -1,64 +0,0 @@ -===================================================================== -MPX LAW & Coherency Module Device Tree Binding -Copyright (C) 2009 Freescale Semiconductor Inc. -===================================================================== - -Local Access Window (LAW) Node - -The LAW node represents the region of CCSR space where local access -windows are configured. For MCM based devices this is the first 4k -of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some -number of local access windows as specified by fsl,num-laws. - -PROPERTIES - - - compatible - Usage: required - Value type: <string> - Definition: Must include "fsl,mcm-law" - - - reg - Usage: required - Value type: <prop-encoded-array> - Definition: A standard property. The value specifies the - physical address offset and length of the CCSR space - registers. - - - fsl,num-laws - Usage: required - Value type: <u32> - Definition: The value specifies the number of local access - windows for this device. - -===================================================================== - -MPX Coherency Module Node - -The MPX LAW node represents the region of CCSR space where MCM config -and error reporting registers exist, this is the second 4k (0x1000) -of CCSR space. - -PROPERTIES - - - compatible - Usage: required - Value type: <string> - Definition: Must include "fsl,CHIP-mcm", "fsl,mcm" where - CHIP is the processor (mpc8641, mpc8610, etc.) - - - reg - Usage: required - Value type: <prop-encoded-array> - Definition: A standard property. The value specifies the - physical address offset and length of the CCSR space - registers. - - - interrupts - Usage: required - Value type: <prop-encoded-array> - - - interrupt-parent - Usage: required - Value type: <phandle> - -===================================================================== diff --git a/Documentation/powerpc/dts-bindings/fsl/mcu-mpc8349emitx.txt b/Documentation/powerpc/dts-bindings/fsl/mcu-mpc8349emitx.txt deleted file mode 100644 index 0f766333b6e..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mcu-mpc8349emitx.txt +++ /dev/null @@ -1,17 +0,0 @@ -Freescale MPC8349E-mITX-compatible Power Management Micro Controller Unit (MCU) - -Required properties: -- compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx". -- reg : should specify I2C address (0x0a). -- #gpio-cells : should be 2. -- gpio-controller : should be present. - -Example: - -mcu@0a { - #gpio-cells = <2>; - compatible = "fsl,mc9s08qg8-mpc8349emitx", - "fsl,mcu-mpc8349emitx"; - reg = <0x0a>; - gpio-controller; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt deleted file mode 100644 index 8832e879891..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt +++ /dev/null @@ -1,70 +0,0 @@ -MPC5121 PSC Device Tree Bindings - -PSC in UART mode ----------------- - -For PSC in UART mode the needed PSC serial devices -are specified by fsl,mpc5121-psc-uart nodes in the -fsl,mpc5121-immr SoC node. Additionally the PSC FIFO -Controller node fsl,mpc5121-psc-fifo is requered there: - -fsl,mpc5121-psc-uart nodes --------------------------- - -Required properties : - - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" - - cell-index : Index of the PSC in hardware - - reg : Offset and length of the register set for the PSC device - - interrupts : <a b> where a is the interrupt number of the - PSC FIFO Controller and b is a field that represents an - encoding of the sense and level information for the interrupt. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Recommended properties : - - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) - - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) - - -fsl,mpc5121-psc-fifo node -------------------------- - -Required properties : - - compatible : Should be "fsl,mpc5121-psc-fifo" - - reg : Offset and length of the register set for the PSC - FIFO Controller - - interrupts : <a b> where a is the interrupt number of the - PSC FIFO Controller and b is a field that represents an - encoding of the sense and level information for the interrupt. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - -Example for a board using PSC0 and PSC1 devices in serial mode: - -serial@11000 { - compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; - cell-index = <0>; - reg = <0x11000 0x100>; - interrupts = <40 0x8>; - interrupt-parent = < &ipic >; - fsl,rx-fifo-size = <16>; - fsl,tx-fifo-size = <16>; -}; - -serial@11100 { - compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; - cell-index = <1>; - reg = <0x11100 0x100>; - interrupts = <40 0x8>; - interrupt-parent = < &ipic >; - fsl,rx-fifo-size = <16>; - fsl,tx-fifo-size = <16>; -}; - -pscfifo@11f00 { - compatible = "fsl,mpc5121-psc-fifo"; - reg = <0x11f00 0x100>; - interrupts = <40 0x8>; - interrupt-parent = < &ipic >; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt deleted file mode 100644 index 4ccb2cd5df9..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt +++ /dev/null @@ -1,198 +0,0 @@ -MPC5200 Device Tree Bindings ----------------------------- - -(c) 2006-2009 Secret Lab Technologies Ltd -Grant Likely <grant.likely@secretlab.ca> - -Naming conventions ------------------- -For mpc5200 on-chip devices, the format for each compatible value is -<chip>-<device>[-<mode>]. The OS should be able to match a device driver -to the device based solely on the compatible value. If two drivers -match on the compatible list; the 'most compatible' driver should be -selected. - -The split between the MPC5200 and the MPC5200B leaves a bit of a -conundrum. How should the compatible property be set up to provide -maximum compatibility information; but still accurately describe the -chip? For the MPC5200; the answer is easy. Most of the SoC devices -originally appeared on the MPC5200. Since they didn't exist anywhere -else; the 5200 compatible properties will contain only one item; -"fsl,mpc5200-<device>". - -The 5200B is almost the same as the 5200, but not quite. It fixes -silicon bugs and it adds a small number of enhancements. Most of the -devices either provide exactly the same interface as on the 5200. A few -devices have extra functions but still have a backwards compatible mode. -To express this information as completely as possible, 5200B device trees -should have two items in the compatible list: - compatible = "fsl,mpc5200b-<device>","fsl,mpc5200-<device>"; - -It is *strongly* recommended that 5200B device trees follow this convention -(instead of only listing the base mpc5200 item). - -ie. ethernet on mpc5200: compatible = "fsl,mpc5200-fec"; - ethernet on mpc5200b: compatible = "fsl,mpc5200b-fec", "fsl,mpc5200-fec"; - -Modal devices, like PSCs, also append the configured function to the -end of the compatible field. ie. A PSC in i2s mode would specify -"fsl,mpc5200-psc-i2s", not "fsl,mpc5200-i2s". This convention is chosen to -avoid naming conflicts with non-psc devices providing the same -function. For example, "fsl,mpc5200-spi" and "fsl,mpc5200-psc-spi" describe -the mpc5200 simple spi device and a PSC spi mode respectively. - -At the time of writing, exact chip may be either 'fsl,mpc5200' or -'fsl,mpc5200b'. - -The soc node ------------- -This node describes the on chip SOC peripherals. Every mpc5200 based -board will have this node, and as such there is a common naming -convention for SOC devices. - -Required properties: -name description ----- ----------- -ranges Memory range of the internal memory mapped registers. - Should be <0 [baseaddr] 0xc000> -reg Should be <[baseaddr] 0x100> -compatible mpc5200: "fsl,mpc5200-immr" - mpc5200b: "fsl,mpc5200b-immr" -system-frequency 'fsystem' frequency in Hz; XLB, IPB, USB and PCI - clocks are derived from the fsystem clock. -bus-frequency IPB bus frequency in Hz. Clock rate - used by most of the soc devices. - -soc child nodes ---------------- -Any on chip SOC devices available to Linux must appear as soc5200 child nodes. - -Note: The tables below show the value for the mpc5200. A mpc5200b device -tree should use the "fsl,mpc5200b-<device>","fsl,mpc5200-<device>" form. - -Required soc5200 child nodes: -name compatible Description ----- ---------- ----------- -cdm@<addr> fsl,mpc5200-cdm Clock Distribution -interrupt-controller@<addr> fsl,mpc5200-pic need an interrupt - controller to boot -bestcomm@<addr> fsl,mpc5200-bestcomm Bestcomm DMA controller - -Recommended soc5200 child nodes; populate as needed for your board -name compatible Description ----- ---------- ----------- -timer@<addr> fsl,mpc5200-gpt General purpose timers -gpio@<addr> fsl,mpc5200-gpio MPC5200 simple gpio controller -gpio@<addr> fsl,mpc5200-gpio-wkup MPC5200 wakeup gpio controller -rtc@<addr> fsl,mpc5200-rtc Real time clock -mscan@<addr> fsl,mpc5200-mscan CAN bus controller -pci@<addr> fsl,mpc5200-pci PCI bridge -serial@<addr> fsl,mpc5200-psc-uart PSC in serial mode -i2s@<addr> fsl,mpc5200-psc-i2s PSC in i2s mode -ac97@<addr> fsl,mpc5200-psc-ac97 PSC in ac97 mode -spi@<addr> fsl,mpc5200-psc-spi PSC in spi mode -irda@<addr> fsl,mpc5200-psc-irda PSC in IrDA mode -spi@<addr> fsl,mpc5200-spi MPC5200 spi device -ethernet@<addr> fsl,mpc5200-fec MPC5200 ethernet device -ata@<addr> fsl,mpc5200-ata IDE ATA interface -i2c@<addr> fsl,mpc5200-i2c I2C controller -usb@<addr> fsl,mpc5200-ohci,ohci-be USB controller -xlb@<addr> fsl,mpc5200-xlb XLB arbitrator - -fsl,mpc5200-gpt nodes ---------------------- -On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board -design supports the internal wdt, then the device node for GPT0 should -include the empty property 'fsl,has-wdt'. Note that this does not activate -the watchdog. The timer will function as a GPT if the timer api is used, and -it will function as watchdog if the watchdog device is used. The watchdog -mode has priority over the gpt mode, i.e. if the watchdog is activated, any -gpt api call to this timer will fail with -EBUSY. - -If you add the property - fsl,wdt-on-boot = <n>; -GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it. -If n>0, the watchdog is started with a timeout of n seconds. If n=0, the -configuration of the watchdog is not touched. This is useful in two cases: -- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later; -- do not touch a configuration assigned by the boot loader which supervises - the boot process itself. - -The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option. - -An mpc5200-gpt can be used as a single line GPIO controller. To do so, -add the following properties to the gpt node: - gpio-controller; - #gpio-cells = <2>; -When referencing the GPIO line from another node, the first cell must always -be zero and the second cell represents the gpio flags and described in the -gpio device tree binding. - -An mpc5200-gpt can be used as a single line edge sensitive interrupt -controller. To do so, add the following properties to the gpt node: - interrupt-controller; - #interrupt-cells = <1>; -When referencing the IRQ line from another node, the cell represents the -sense mode; 1 for edge rising, 2 for edge falling. - -fsl,mpc5200-psc nodes ---------------------- -The PSCs should include a cell-index which is the index of the PSC in -hardware. cell-index is used to determine which shared SoC registers to -use when setting up PSC clocking. cell-index number starts at '0'. ie: - PSC1 has 'cell-index = <0>' - PSC4 has 'cell-index = <3>' - -PSC in i2s mode: The mpc5200 and mpc5200b PSCs are not compatible when in -i2s mode. An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the -compatible field. - - -fsl,mpc5200-gpio and fsl,mpc5200-gpio-wkup nodes ------------------------------------------------- -Each GPIO controller node should have the empty property gpio-controller and -#gpio-cells set to 2. First cell is the GPIO number which is interpreted -according to the bit numbers in the GPIO control registers. The second cell -is for flags which is currently unused. - -fsl,mpc5200-fec nodes ---------------------- -The FEC node can specify one of the following properties to configure -the MII link: -- fsl,7-wire-mode - An empty property that specifies the link uses 7-wire - mode instead of MII -- current-speed - Specifies that the MII should be configured for a fixed - speed. This property should contain two cells. The - first cell specifies the speed in Mbps and the second - should be '0' for half duplex and '1' for full duplex -- phy-handle - Contains a phandle to an Ethernet PHY. - -Interrupt controller (fsl,mpc5200-pic) node -------------------------------------------- -The mpc5200 pic binding splits hardware IRQ numbers into two levels. The -split reflects the layout of the PIC hardware itself, which groups -interrupts into one of three groups; CRIT, MAIN or PERP. Also, the -Bestcomm dma engine has it's own set of interrupt sources which are -cascaded off of peripheral interrupt 0, which the driver interprets as a -fourth group, SDMA. - -The interrupts property for device nodes using the mpc5200 pic consists -of three cells; <L1 L2 level> - - L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3] - L2 := interrupt number; directly mapped from the value in the - "ICTL PerStat, MainStat, CritStat Encoded Register" - level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3] - -For external IRQs, use the following interrupt property values (how to -specify external interrupts is a frequently asked question): -External interrupts: - external irq0: interrupts = <0 0 n>; - external irq1: interrupts = <1 1 n>; - external irq2: interrupts = <1 2 n>; - external irq3: interrupts = <1 3 n>; -'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low) - -fsl,mpc5200-mscan nodes ------------------------ -See file can.txt in this directory. diff --git a/Documentation/powerpc/dts-bindings/fsl/mpic.txt b/Documentation/powerpc/dts-bindings/fsl/mpic.txt deleted file mode 100644 index 71e39cf3215..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mpic.txt +++ /dev/null @@ -1,42 +0,0 @@ -* OpenPIC and its interrupt numbers on Freescale's e500/e600 cores - -The OpenPIC specification does not specify which interrupt source has to -become which interrupt number. This is up to the software implementation -of the interrupt controller. The only requirement is that every -interrupt source has to have an unique interrupt number / vector number. -To accomplish this the current implementation assigns the number zero to -the first source, the number one to the second source and so on until -all interrupt sources have their unique number. -Usually the assigned vector number equals the interrupt number mentioned -in the documentation for a given core / CPU. This is however not true -for the e500 cores (MPC85XX CPUs) where the documentation distinguishes -between internal and external interrupt sources and starts counting at -zero for both of them. - -So what to write for external interrupt source X or internal interrupt -source Y into the device tree? Here is an example: - -The memory map for the interrupt controller in the MPC8544[0] shows, -that the first interrupt source starts at 0x5_0000 (PIC Register Address -Map-Interrupt Source Configuration Registers). This source becomes the -number zero therefore: - External interrupt 0 = interrupt number 0 - External interrupt 1 = interrupt number 1 - External interrupt 2 = interrupt number 2 - ... -Every interrupt number allocates 0x20 bytes register space. So to get -its number it is sufficient to shift the lower 16bits to right by five. -So for the external interrupt 10 we have: - 0x0140 >> 5 = 10 - -After the external sources, the internal sources follow. The in core I2C -controller on the MPC8544 for instance has the internal source number -27. Oo obtain its interrupt number we take the lower 16bits of its memory -address (0x5_0560) and shift it right: - 0x0560 >> 5 = 43 - -Therefore the I2C device node for the MPC8544 CPU has to have the -interrupt number 43 specified in the device tree. - -[0] MPC8544E PowerQUICCTM III, Integrated Host Processor Family Reference Manual - MPC8544ERM Rev. 1 10/2007 diff --git a/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt b/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt deleted file mode 100644 index bcc30bac683..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt +++ /dev/null @@ -1,36 +0,0 @@ -* Freescale MSI interrupt controller - -Required properties: -- compatible : compatible list, contains 2 entries, - first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, - etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on - the parent type. -- reg : should contain the address and the length of the shared message - interrupt register set. -- msi-available-ranges: use <start count> style section to define which - msi interrupt can be used in the 256 msi interrupts. This property is - optional, without this, all the 256 MSI interrupts can be used. -- interrupts : each one of the interrupts here is one entry per 32 MSIs, - and routed to the host interrupt controller. the interrupts should - be set as edge sensitive. -- interrupt-parent: the phandle for the interrupt controller - that services interrupts for this device. for 83xx cpu, the interrupts - are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed - to MPIC. - -Example: - msi@41600 { - compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; - reg = <0x41600 0x80>; - msi-available-ranges = <0 0x100>; - interrupts = < - 0xe0 0 - 0xe1 0 - 0xe2 0 - 0xe3 0 - 0xe4 0 - 0xe5 0 - 0xe6 0 - 0xe7 0>; - interrupt-parent = <&mpic>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/pmc.txt b/Documentation/powerpc/dts-bindings/fsl/pmc.txt deleted file mode 100644 index 07256b7ffca..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/pmc.txt +++ /dev/null @@ -1,63 +0,0 @@ -* Power Management Controller - -Properties: -- compatible: "fsl,<chip>-pmc". - - "fsl,mpc8349-pmc" should be listed for any chip whose PMC is - compatible. "fsl,mpc8313-pmc" should also be listed for any chip - whose PMC is compatible, and implies deep-sleep capability. - - "fsl,mpc8548-pmc" should be listed for any chip whose PMC is - compatible. "fsl,mpc8536-pmc" should also be listed for any chip - whose PMC is compatible, and implies deep-sleep capability. - - "fsl,mpc8641d-pmc" should be listed for any chip whose PMC is - compatible; all statements below that apply to "fsl,mpc8548-pmc" also - apply to "fsl,mpc8641d-pmc". - - Compatibility does not include bit assignments in SCCR/PMCDR/DEVDISR; these - bit assignments are indicated via the sleep specifier in each device's - sleep property. - -- reg: For devices compatible with "fsl,mpc8349-pmc", the first resource - is the PMC block, and the second resource is the Clock Configuration - block. - - For devices compatible with "fsl,mpc8548-pmc", the first resource - is a 32-byte block beginning with DEVDISR. - -- interrupts: For "fsl,mpc8349-pmc"-compatible devices, the first - resource is the PMC block interrupt. - -- fsl,mpc8313-wakeup-timer: For "fsl,mpc8313-pmc"-compatible devices, - this is a phandle to an "fsl,gtm" node on which timer 4 can be used as - a wakeup source from deep sleep. - -Sleep specifiers: - - fsl,mpc8349-pmc: Sleep specifiers consist of one cell. For each bit - that is set in the cell, the corresponding bit in SCCR will be saved - and cleared on suspend, and restored on resume. This sleep controller - supports disabling and resuming devices at any time. - - fsl,mpc8536-pmc: Sleep specifiers consist of three cells, the third of - which will be ORed into PMCDR upon suspend, and cleared from PMCDR - upon resume. The first two cells are as described for fsl,mpc8578-pmc. - This sleep controller only supports disabling devices during system - sleep, or permanently. - - fsl,mpc8548-pmc: Sleep specifiers consist of one or two cells, the - first of which will be ORed into DEVDISR (and the second into - DEVDISR2, if present -- this cell should be zero or absent if the - hardware does not have DEVDISR2) upon a request for permanent device - disabling. This sleep controller does not support configuring devices - to disable during system sleep (unless supported by another compatible - match), or dynamically. - -Example: - - power@b00 { - compatible = "fsl,mpc8313-pmc", "fsl,mpc8349-pmc"; - reg = <0xb00 0x100 0xa00 0x100>; - interrupts = <80 8>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/sata.txt b/Documentation/powerpc/dts-bindings/fsl/sata.txt deleted file mode 100644 index b46bcf46c3d..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/sata.txt +++ /dev/null @@ -1,29 +0,0 @@ -* Freescale 8xxx/3.0 Gb/s SATA nodes - -SATA nodes are defined to describe on-chip Serial ATA controllers. -Each SATA port should have its own node. - -Required properties: -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-sata", where CHIP is the processor - (mpc8315, mpc8379, etc.) and the second is - "fsl,pq-sata" -- interrupts : <interrupt mapping for SATA IRQ> -- cell-index : controller index. - 1 for controller @ 0x18000 - 2 for controller @ 0x19000 - 3 for controller @ 0x1a000 - 4 for controller @ 0x1b000 - -Optional properties: -- interrupt-parent : optional, if needed for interrupt mapping -- reg : <registers mapping> - -Example: - sata@18000 { - compatible = "fsl,mpc8379-sata", "fsl,pq-sata"; - reg = <0x18000 0x1000>; - cell-index = <1>; - interrupts = <2c 8>; - interrupt-parent = < &ipic >; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/sec.txt b/Documentation/powerpc/dts-bindings/fsl/sec.txt deleted file mode 100644 index 2b6f2d45c45..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/sec.txt +++ /dev/null @@ -1,68 +0,0 @@ -Freescale SoC SEC Security Engines - -Required properties: - -- compatible : Should contain entries for this and backward compatible - SEC versions, high to low, e.g., "fsl,sec2.1", "fsl,sec2.0" -- reg : Offset and length of the register set for the device -- interrupts : the SEC's interrupt number -- fsl,num-channels : An integer representing the number of channels - available. -- fsl,channel-fifo-len : An integer representing the number of - descriptor pointers each channel fetch fifo can hold. -- fsl,exec-units-mask : The bitmask representing what execution units - (EUs) are available. It's a single 32-bit cell. EU information - should be encoded following the SEC's Descriptor Header Dword - EU_SEL0 field documentation, i.e. as follows: - - bit 0 = reserved - should be 0 - bit 1 = set if SEC has the ARC4 EU (AFEU) - bit 2 = set if SEC has the DES/3DES EU (DEU) - bit 3 = set if SEC has the message digest EU (MDEU/MDEU-A) - bit 4 = set if SEC has the random number generator EU (RNG) - bit 5 = set if SEC has the public key EU (PKEU) - bit 6 = set if SEC has the AES EU (AESU) - bit 7 = set if SEC has the Kasumi EU (KEU) - bit 8 = set if SEC has the CRC EU (CRCU) - bit 11 = set if SEC has the message digest EU extended alg set (MDEU-B) - -remaining bits are reserved for future SEC EUs. - -- fsl,descriptor-types-mask : The bitmask representing what descriptors - are available. It's a single 32-bit cell. Descriptor type information - should be encoded following the SEC's Descriptor Header Dword DESC_TYPE - field documentation, i.e. as follows: - - bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type - bit 1 = set if SEC supports the ipsec_esp descriptor type - bit 2 = set if SEC supports the common_nonsnoop desc. type - bit 3 = set if SEC supports the 802.11i AES ccmp desc. type - bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type - bit 5 = set if SEC supports the srtp descriptor type - bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type - bit 7 = set if SEC supports the pkeu_assemble descriptor type - bit 8 = set if SEC supports the aesu_key_expand_output desc.type - bit 9 = set if SEC supports the pkeu_ptmul descriptor type - bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type - bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type - - ..and so on and so forth. - -Optional properties: - -- interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Example: - - /* MPC8548E */ - crypto@30000 { - compatible = "fsl,sec2.1", "fsl,sec2.0"; - reg = <0x30000 0x10000>; - interrupts = <29 2>; - interrupt-parent = <&mpic>; - fsl,num-channels = <4>; - fsl,channel-fifo-len = <24>; - fsl,exec-units-mask = <0xfe>; - fsl,descriptor-types-mask = <0x12b0ebf>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/spi.txt b/Documentation/powerpc/dts-bindings/fsl/spi.txt deleted file mode 100644 index 777abd7399d..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/spi.txt +++ /dev/null @@ -1,53 +0,0 @@ -* SPI (Serial Peripheral Interface) - -Required properties: -- cell-index : QE SPI subblock index. - 0: QE subblock SPI1 - 1: QE subblock SPI2 -- compatible : should be "fsl,spi". -- mode : the SPI operation mode, it can be "cpu" or "cpu-qe". -- reg : Offset and length of the register set for the device -- interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. -- interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Optional properties: -- gpios : specifies the gpio pins to be used for chipselects. - The gpios will be referred to as reg = <index> in the SPI child nodes. - If unspecified, a single SPI device without a chip select can be used. - -Example: - spi@4c0 { - cell-index = <0>; - compatible = "fsl,spi"; - reg = <4c0 40>; - interrupts = <82 0>; - interrupt-parent = <700>; - mode = "cpu"; - gpios = <&gpio 18 1 // device reg=<0> - &gpio 19 1>; // device reg=<1> - }; - - -* eSPI (Enhanced Serial Peripheral Interface) - -Required properties: -- compatible : should be "fsl,mpc8536-espi". -- reg : Offset and length of the register set for the device. -- interrupts : should contain eSPI interrupt, the device has one interrupt. -- fsl,espi-num-chipselects : the number of the chipselect signals. - -Example: - spi@110000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc8536-espi"; - reg = <0x110000 0x1000>; - interrupts = <53 0x2>; - interrupt-parent = <&mpic>; - fsl,espi-num-chipselects = <4>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/ssi.txt b/Documentation/powerpc/dts-bindings/fsl/ssi.txt deleted file mode 100644 index 5ff76c9c57d..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/ssi.txt +++ /dev/null @@ -1,73 +0,0 @@ -Freescale Synchronous Serial Interface - -The SSI is a serial device that communicates with audio codecs. It can -be programmed in AC97, I2S, left-justified, or right-justified modes. - -Required properties: -- compatible: Compatible list, contains "fsl,ssi". -- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. -- reg: Offset and length of the register set for the device. -- interrupts: <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and - level information for the interrupt. This should be - encoded based on the information in section 2) - depending on the type of interrupt controller you - have. -- interrupt-parent: The phandle for the interrupt controller that - services interrupts for this device. -- fsl,mode: The operating mode for the SSI interface. - "i2s-slave" - I2S mode, SSI is clock slave - "i2s-master" - I2S mode, SSI is clock master - "lj-slave" - left-justified mode, SSI is clock slave - "lj-master" - l.j. mode, SSI is clock master - "rj-slave" - right-justified mode, SSI is clock slave - "rj-master" - r.j., SSI is clock master - "ac97-slave" - AC97 mode, SSI is clock slave - "ac97-master" - AC97 mode, SSI is clock master -- fsl,playback-dma: Phandle to a node for the DMA channel to use for - playback of audio. This is typically dictated by SOC - design. See the notes below. -- fsl,capture-dma: Phandle to a node for the DMA channel to use for - capture (recording) of audio. This is typically dictated - by SOC design. See the notes below. -- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. - This number is the maximum allowed value for SFCSR[TFWM0]. -- fsl,ssi-asynchronous: - If specified, the SSI is to be programmed in asynchronous - mode. In this mode, pins SRCK, STCK, SRFS, and STFS must - all be connected to valid signals. In synchronous mode, - SRCK and SRFS are ignored. Asynchronous mode allows - playback and capture to use different sample sizes and - sample rates. Some drivers may require that SRCK and STCK - be connected together, and SRFS and STFS be connected - together. This would still allow different sample sizes, - but not different sample rates. - -Optional properties: -- codec-handle: Phandle to a 'codec' node that defines an audio - codec connected to this SSI. This node is typically - a child of an I2C or other control node. - -Child 'codec' node required properties: -- compatible: Compatible list, contains the name of the codec - -Child 'codec' node optional properties: -- clock-frequency: The frequency of the input clock, which typically comes - from an on-board dedicated oscillator. - -Notes on fsl,playback-dma and fsl,capture-dma: - -On SOCs that have an SSI, specific DMA channels are hard-wired for playback -and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for -playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for -playback and DMA channel 3 for capture. The developer can choose which -DMA controller to use, but the channels themselves are hard-wired. The -purpose of these two properties is to represent this hardware design. - -The device tree nodes for the DMA channels that are referenced by -"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with -"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g. -"fsl,mpc8610-dma-channel") can remain. If these nodes are left as -"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA -drivers (fsldma) will attempt to use them, and it will conflict with the -sound drivers. diff --git a/Documentation/powerpc/dts-bindings/fsl/tsec.txt b/Documentation/powerpc/dts-bindings/fsl/tsec.txt deleted file mode 100644 index edb7ae19e86..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/tsec.txt +++ /dev/null @@ -1,76 +0,0 @@ -* MDIO IO device - -The MDIO is a bus to which the PHY devices are connected. For each -device that exists on this bus, a child node should be created. See -the definition of the PHY node in booting-without-of.txt for an example -of how to define a PHY. - -Required properties: - - reg : Offset and length of the register set for the device - - compatible : Should define the compatible device type for the - mdio. Currently, this is most likely to be "fsl,gianfar-mdio" - -Example: - - mdio@24520 { - reg = <24520 20>; - compatible = "fsl,gianfar-mdio"; - - ethernet-phy@0 { - ...... - }; - }; - -* TBI Internal MDIO bus - -As of this writing, every tsec is associated with an internal TBI PHY. -This PHY is accessed through the local MDIO bus. These buses are defined -similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi". -The TBI PHYs underneath them are similar to normal PHYs, but the reg property -is considered instructive, rather than descriptive. The reg property should -be chosen so it doesn't interfere with other PHYs on the bus. - -* Gianfar-compatible ethernet nodes - -Properties: - - - device_type : Should be "network" - - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" - - compatible : Should be "gianfar" - - reg : Offset and length of the register set for the device - - local-mac-address : List of bytes representing the ethernet address of - this controller - - interrupts : For FEC devices, the first interrupt is the device's - interrupt. For TSEC and eTSEC devices, the first interrupt is - transmit, the second is receive, and the third is error. - - phy-handle : The phandle for the PHY connected to this ethernet - controller. - - fixed-link : <a b c d e> where a is emulated phy id - choose any, - but unique to the all specified fixed-links, b is duplex - 0 half, - 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no - pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause. - - phy-connection-type : a string naming the controller/PHY interface type, - i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii", - "tbi", or "rtbi". This property is only really needed if the connection - is of type "rgmii-id", as all other connection types are detected by - hardware. - - fsl,magic-packet : If present, indicates that the hardware supports - waking up via magic packet. - - bd-stash : If present, indicates that the hardware supports stashing - buffer descriptors in the L2. - - rx-stash-len : Denotes the number of bytes of a received buffer to stash - in the L2. - - rx-stash-idx : Denotes the index of the first byte from the received - buffer to stash in the L2. - -Example: - ethernet@24000 { - device_type = "network"; - model = "TSEC"; - compatible = "gianfar"; - reg = <0x24000 0x1000>; - local-mac-address = [ 00 E0 0C 00 73 00 ]; - interrupts = <29 2 30 2 34 2>; - interrupt-parent = <&mpic>; - phy-handle = <&phy0> - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt b/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt deleted file mode 100644 index a48b2cadc7f..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt +++ /dev/null @@ -1,63 +0,0 @@ -Freescale Localbus UPM programmed to work with NAND flash - -Required properties: -- compatible : "fsl,upm-nand". -- reg : should specify localbus chip select and size used for the chip. -- fsl,upm-addr-offset : UPM pattern offset for the address latch. -- fsl,upm-cmd-offset : UPM pattern offset for the command latch. - -Optional properties: -- fsl,upm-wait-flags : add chip-dependent short delays after running the - UPM pattern (0x1), after writing a data byte (0x2) or after - writing out a buffer (0x4). -- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support. - The corresponding address lines are used to select the chip. -- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins - (R/B#). For multi-chip devices, "n" GPIO definitions are required - according to the number of chips. -- chip-delay : chip dependent delay for transfering data from array to - read registers (tR). Required if property "gpios" is not used - (R/B# pins not connected). - -Examples: - -upm@1,0 { - compatible = "fsl,upm-nand"; - reg = <1 0 1>; - fsl,upm-addr-offset = <16>; - fsl,upm-cmd-offset = <8>; - gpios = <&qe_pio_e 18 0>; - - flash { - #address-cells = <1>; - #size-cells = <1>; - compatible = "..."; - - partition@0 { - ... - }; - }; -}; - -upm@3,0 { - #address-cells = <0>; - #size-cells = <0>; - compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand"; - reg = <3 0x0 0x800>; - fsl,upm-addr-offset = <0x10>; - fsl,upm-cmd-offset = <0x08>; - /* Multi-chip NAND device */ - fsl,upm-addr-line-cs-offsets = <0x0 0x200>; - fsl,upm-wait-flags = <0x5>; - chip-delay = <25>; // in micro-seconds - - nand@0 { - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "fs"; - reg = <0x00000000 0x10000000>; - }; - }; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/usb.txt b/Documentation/powerpc/dts-bindings/fsl/usb.txt deleted file mode 100644 index bd5723f0b67..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/usb.txt +++ /dev/null @@ -1,81 +0,0 @@ -Freescale SOC USB controllers - -The device node for a USB controller that is part of a Freescale -SOC is as described in the document "Open Firmware Recommended -Practice : Universal Serial Bus" with the following modifications -and additions : - -Required properties : - - compatible : Should be "fsl-usb2-mph" for multi port host USB - controllers, or "fsl-usb2-dr" for dual role USB controllers - or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121 - - phy_type : For multi port host USB controllers, should be one of - "ulpi", or "serial". For dual role USB controllers, should be - one of "ulpi", "utmi", "utmi_wide", or "serial". - - reg : Offset and length of the register set for the device - - port0 : boolean; if defined, indicates port0 is connected for - fsl-usb2-mph compatible controllers. Either this property or - "port1" (or both) must be defined for "fsl-usb2-mph" compatible - controllers. - - port1 : boolean; if defined, indicates port1 is connected for - fsl-usb2-mph compatible controllers. Either this property or - "port0" (or both) must be defined for "fsl-usb2-mph" compatible - controllers. - - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible - controllers. Can be "host", "peripheral", or "otg". Default to - "host" if not defined for backward compatibility. - -Recommended properties : - - interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Optional properties : - - fsl,invert-drvvbus : boolean; for MPC5121 USB0 only. Indicates the - port power polarity of internal PHY signal DRVVBUS is inverted. - - fsl,invert-pwr-fault : boolean; for MPC5121 USB0 only. Indicates - the PWR_FAULT signal polarity is inverted. - -Example multi port host USB controller device node : - usb@22000 { - compatible = "fsl-usb2-mph"; - reg = <22000 1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <700>; - interrupts = <27 1>; - phy_type = "ulpi"; - port0; - port1; - }; - -Example dual role USB controller device node : - usb@23000 { - compatible = "fsl-usb2-dr"; - reg = <23000 1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <700>; - interrupts = <26 1>; - dr_mode = "otg"; - phy = "ulpi"; - }; - -Example dual role USB controller device node for MPC5121ADS: - - usb@4000 { - compatible = "fsl,mpc5121-usb2-dr"; - reg = <0x4000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = < &ipic >; - interrupts = <44 0x8>; - dr_mode = "otg"; - phy_type = "utmi_wide"; - fsl,invert-drvvbus; - fsl,invert-pwr-fault; - }; diff --git a/Documentation/powerpc/dts-bindings/gpio/gpio.txt b/Documentation/powerpc/dts-bindings/gpio/gpio.txt deleted file mode 100644 index edaa84d288a..00000000000 --- a/Documentation/powerpc/dts-bindings/gpio/gpio.txt +++ /dev/null @@ -1,50 +0,0 @@ -Specifying GPIO information for devices -============================================ - -1) gpios property ------------------ - -Nodes that makes use of GPIOs should define them using `gpios' property, -format of which is: <&gpio-controller1-phandle gpio1-specifier - &gpio-controller2-phandle gpio2-specifier - 0 /* holes are permitted, means no GPIO 3 */ - &gpio-controller4-phandle gpio4-specifier - ...>; - -Note that gpio-specifier length is controller dependent. - -gpio-specifier may encode: bank, pin position inside the bank, -whether pin is open-drain and whether pin is logically inverted. - -Example of the node using GPIOs: - - node { - gpios = <&qe_pio_e 18 0>; - }; - -In this example gpio-specifier is "18 0" and encodes GPIO pin number, -and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. - -2) gpio-controller nodes ------------------------- - -Every GPIO controller node must have #gpio-cells property defined, -this information will be used to translate gpio-specifiers. - -Example of two SOC GPIO banks defined as gpio-controller nodes: - - qe_pio_a: gpio-controller@1400 { - #gpio-cells = <2>; - compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; - reg = <0x1400 0x18>; - gpio-controller; - }; - - qe_pio_e: gpio-controller@1460 { - #gpio-cells = <2>; - compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; - reg = <0x1460 0x18>; - gpio-controller; - }; - - diff --git a/Documentation/powerpc/dts-bindings/gpio/led.txt b/Documentation/powerpc/dts-bindings/gpio/led.txt deleted file mode 100644 index 064db928c3c..00000000000 --- a/Documentation/powerpc/dts-bindings/gpio/led.txt +++ /dev/null @@ -1,58 +0,0 @@ -LEDs connected to GPIO lines - -Required properties: -- compatible : should be "gpio-leds". - -Each LED is represented as a sub-node of the gpio-leds device. Each -node's name represents the name of the corresponding LED. - -LED sub-node properties: -- gpios : Should specify the LED's GPIO, see "Specifying GPIO information - for devices" in Documentation/powerpc/booting-without-of.txt. Active - low LEDs should be indicated using flags in the GPIO specifier. -- label : (optional) The label for this LED. If omitted, the label is - taken from the node name (excluding the unit address). -- linux,default-trigger : (optional) This parameter, if present, is a - string defining the trigger assigned to the LED. Current triggers are: - "backlight" - LED will act as a back-light, controlled by the framebuffer - system - "default-on" - LED will turn on, but see "default-state" below - "heartbeat" - LED "double" flashes at a load average based rate - "ide-disk" - LED indicates disk activity - "timer" - LED flashes at a fixed, configurable rate -- default-state: (optional) The initial state of the LED. Valid - values are "on", "off", and "keep". If the LED is already on or off - and the default-state property is set the to same value, then no - glitch should be produced where the LED momentarily turns off (or - on). The "keep" setting will keep the LED at whatever its current - state is, without producing a glitch. The default is off if this - property is not present. - -Examples: - -leds { - compatible = "gpio-leds"; - hdd { - label = "IDE Activity"; - gpios = <&mcu_pio 0 1>; /* Active low */ - linux,default-trigger = "ide-disk"; - }; - - fault { - gpios = <&mcu_pio 1 0>; - /* Keep LED on if BIOS detected hardware fault */ - default-state = "keep"; - }; -}; - -run-control { - compatible = "gpio-leds"; - red { - gpios = <&mpc8572 6 0>; - default-state = "off"; - }; - green { - gpios = <&mpc8572 7 0>; - default-state = "on"; - }; -} diff --git a/Documentation/powerpc/dts-bindings/gpio/mdio.txt b/Documentation/powerpc/dts-bindings/gpio/mdio.txt deleted file mode 100644 index bc954952901..00000000000 --- a/Documentation/powerpc/dts-bindings/gpio/mdio.txt +++ /dev/null @@ -1,19 +0,0 @@ -MDIO on GPIOs - -Currently defined compatibles: -- virtual,gpio-mdio - -MDC and MDIO lines connected to GPIO controllers are listed in the -gpios property as described in section VIII.1 in the following order: - -MDC, MDIO. - -Example: - -mdio { - compatible = "virtual,mdio-gpio"; - #address-cells = <1>; - #size-cells = <0>; - gpios = <&qe_pio_a 11 - &qe_pio_c 6>; -}; diff --git a/Documentation/powerpc/dts-bindings/marvell.txt b/Documentation/powerpc/dts-bindings/marvell.txt deleted file mode 100644 index f1533d91953..00000000000 --- a/Documentation/powerpc/dts-bindings/marvell.txt +++ /dev/null @@ -1,521 +0,0 @@ -Marvell Discovery mv64[345]6x System Controller chips -=========================================================== - -The Marvell mv64[345]60 series of system controller chips contain -many of the peripherals needed to implement a complete computer -system. In this section, we define device tree nodes to describe -the system controller chip itself and each of the peripherals -which it contains. Compatible string values for each node are -prefixed with the string "marvell,", for Marvell Technology Group Ltd. - -1) The /system-controller node - - This node is used to represent the system-controller and must be - present when the system uses a system controller chip. The top-level - system-controller node contains information that is global to all - devices within the system controller chip. The node name begins - with "system-controller" followed by the unit address, which is - the base address of the memory-mapped register set for the system - controller chip. - - Required properties: - - - ranges : Describes the translation of system controller addresses - for memory mapped registers. - - clock-frequency: Contains the main clock frequency for the system - controller chip. - - reg : This property defines the address and size of the - memory-mapped registers contained within the system controller - chip. The address specified in the "reg" property should match - the unit address of the system-controller node. - - #address-cells : Address representation for system controller - devices. This field represents the number of cells needed to - represent the address of the memory-mapped registers of devices - within the system controller chip. - - #size-cells : Size representation for the memory-mapped - registers within the system controller chip. - - #interrupt-cells : Defines the width of cells used to represent - interrupts. - - Optional properties: - - - model : The specific model of the system controller chip. Such - as, "mv64360", "mv64460", or "mv64560". - - compatible : A string identifying the compatibility identifiers - of the system controller chip. - - The system-controller node contains child nodes for each system - controller device that the platform uses. Nodes should not be created - for devices which exist on the system controller chip but are not used - - Example Marvell Discovery mv64360 system-controller node: - - system-controller@f1000000 { /* Marvell Discovery mv64360 */ - #address-cells = <1>; - #size-cells = <1>; - model = "mv64360"; /* Default */ - compatible = "marvell,mv64360"; - clock-frequency = <133333333>; - reg = <0xf1000000 0x10000>; - virtual-reg = <0xf1000000>; - ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */ - 0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */ - 0xa0000000 0xa0000000 0x4000000 /* User FLASH */ - 0x00000000 0xf1000000 0x0010000 /* Bridge's regs */ - 0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */ - - [ child node definitions... ] - } - -2) Child nodes of /system-controller - - a) Marvell Discovery MDIO bus - - The MDIO is a bus to which the PHY devices are connected. For each - device that exists on this bus, a child node should be created. See - the definition of the PHY node below for an example of how to define - a PHY. - - Required properties: - - #address-cells : Should be <1> - - #size-cells : Should be <0> - - device_type : Should be "mdio" - - compatible : Should be "marvell,mv64360-mdio" - - Example: - - mdio { - #address-cells = <1>; - #size-cells = <0>; - device_type = "mdio"; - compatible = "marvell,mv64360-mdio"; - - ethernet-phy@0 { - ...... - }; - }; - - - b) Marvell Discovery ethernet controller - - The Discover ethernet controller is described with two levels - of nodes. The first level describes an ethernet silicon block - and the second level describes up to 3 ethernet nodes within - that block. The reason for the multiple levels is that the - registers for the node are interleaved within a single set - of registers. The "ethernet-block" level describes the - shared register set, and the "ethernet" nodes describe ethernet - port-specific properties. - - Ethernet block node - - Required properties: - - #address-cells : <1> - - #size-cells : <0> - - compatible : "marvell,mv64360-eth-block" - - reg : Offset and length of the register set for this block - - Example Discovery Ethernet block node: - ethernet-block@2000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "marvell,mv64360-eth-block"; - reg = <0x2000 0x2000>; - ethernet@0 { - ....... - }; - }; - - Ethernet port node - - Required properties: - - device_type : Should be "network". - - compatible : Should be "marvell,mv64360-eth". - - reg : Should be <0>, <1>, or <2>, according to which registers - within the silicon block the device uses. - - interrupts : <a> where a is the interrupt number for the port. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - phy : the phandle for the PHY connected to this ethernet - controller. - - local-mac-address : 6 bytes, MAC address - - Example Discovery Ethernet port node: - ethernet@0 { - device_type = "network"; - compatible = "marvell,mv64360-eth"; - reg = <0>; - interrupts = <32>; - interrupt-parent = <&PIC>; - phy = <&PHY0>; - local-mac-address = [ 00 00 00 00 00 00 ]; - }; - - - - c) Marvell Discovery PHY nodes - - Required properties: - - device_type : Should be "ethernet-phy" - - interrupts : <a> where a is the interrupt number for this phy. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - reg : The ID number for the phy, usually a small integer - - Example Discovery PHY node: - ethernet-phy@1 { - device_type = "ethernet-phy"; - compatible = "broadcom,bcm5421"; - interrupts = <76>; /* GPP 12 */ - interrupt-parent = <&PIC>; - reg = <1>; - }; - - - d) Marvell Discovery SDMA nodes - - Represent DMA hardware associated with the MPSC (multiprotocol - serial controllers). - - Required properties: - - compatible : "marvell,mv64360-sdma" - - reg : Offset and length of the register set for this device - - interrupts : <a> where a is the interrupt number for the DMA - device. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery SDMA node: - sdma@4000 { - compatible = "marvell,mv64360-sdma"; - reg = <0x4000 0xc18>; - virtual-reg = <0xf1004000>; - interrupts = <36>; - interrupt-parent = <&PIC>; - }; - - - e) Marvell Discovery BRG nodes - - Represent baud rate generator hardware associated with the MPSC - (multiprotocol serial controllers). - - Required properties: - - compatible : "marvell,mv64360-brg" - - reg : Offset and length of the register set for this device - - clock-src : A value from 0 to 15 which selects the clock - source for the baud rate generator. This value corresponds - to the CLKS value in the BRGx configuration register. See - the mv64x60 User's Manual. - - clock-frequence : The frequency (in Hz) of the baud rate - generator's input clock. - - current-speed : The current speed setting (presumably by - firmware) of the baud rate generator. - - Example Discovery BRG node: - brg@b200 { - compatible = "marvell,mv64360-brg"; - reg = <0xb200 0x8>; - clock-src = <8>; - clock-frequency = <133333333>; - current-speed = <9600>; - }; - - - f) Marvell Discovery CUNIT nodes - - Represent the Serial Communications Unit device hardware. - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery CUNIT node: - cunit@f200 { - reg = <0xf200 0x200>; - }; - - - g) Marvell Discovery MPSCROUTING nodes - - Represent the Discovery's MPSC routing hardware - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery CUNIT node: - mpscrouting@b500 { - reg = <0xb400 0xc>; - }; - - - h) Marvell Discovery MPSCINTR nodes - - Represent the Discovery's MPSC DMA interrupt hardware registers - (SDMA cause and mask registers). - - Required properties: - - reg : Offset and length of the register set for this device - - Example Discovery MPSCINTR node: - mpsintr@b800 { - reg = <0xb800 0x100>; - }; - - - i) Marvell Discovery MPSC nodes - - Represent the Discovery's MPSC (Multiprotocol Serial Controller) - serial port. - - Required properties: - - device_type : "serial" - - compatible : "marvell,mv64360-mpsc" - - reg : Offset and length of the register set for this device - - sdma : the phandle for the SDMA node used by this port - - brg : the phandle for the BRG node used by this port - - cunit : the phandle for the CUNIT node used by this port - - mpscrouting : the phandle for the MPSCROUTING node used by this port - - mpscintr : the phandle for the MPSCINTR node used by this port - - cell-index : the hardware index of this cell in the MPSC core - - max_idle : value needed for MPSC CHR3 (Maximum Frame Length) - register - - interrupts : <a> where a is the interrupt number for the MPSC. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery MPSCINTR node: - mpsc@8000 { - device_type = "serial"; - compatible = "marvell,mv64360-mpsc"; - reg = <0x8000 0x38>; - virtual-reg = <0xf1008000>; - sdma = <&SDMA0>; - brg = <&BRG0>; - cunit = <&CUNIT>; - mpscrouting = <&MPSCROUTING>; - mpscintr = <&MPSCINTR>; - cell-index = <0>; - max_idle = <40>; - interrupts = <40>; - interrupt-parent = <&PIC>; - }; - - - j) Marvell Discovery Watch Dog Timer nodes - - Represent the Discovery's watchdog timer hardware - - Required properties: - - compatible : "marvell,mv64360-wdt" - - reg : Offset and length of the register set for this device - - Example Discovery Watch Dog Timer node: - wdt@b410 { - compatible = "marvell,mv64360-wdt"; - reg = <0xb410 0x8>; - }; - - - k) Marvell Discovery I2C nodes - - Represent the Discovery's I2C hardware - - Required properties: - - device_type : "i2c" - - compatible : "marvell,mv64360-i2c" - - reg : Offset and length of the register set for this device - - interrupts : <a> where a is the interrupt number for the I2C. - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery I2C node: - compatible = "marvell,mv64360-i2c"; - reg = <0xc000 0x20>; - virtual-reg = <0xf100c000>; - interrupts = <37>; - interrupt-parent = <&PIC>; - }; - - - l) Marvell Discovery PIC (Programmable Interrupt Controller) nodes - - Represent the Discovery's PIC hardware - - Required properties: - - #interrupt-cells : <1> - - #address-cells : <0> - - compatible : "marvell,mv64360-pic" - - reg : Offset and length of the register set for this device - - interrupt-controller - - Example Discovery PIC node: - pic { - #interrupt-cells = <1>; - #address-cells = <0>; - compatible = "marvell,mv64360-pic"; - reg = <0x0 0x88>; - interrupt-controller; - }; - - - m) Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes - - Represent the Discovery's MPP hardware - - Required properties: - - compatible : "marvell,mv64360-mpp" - - reg : Offset and length of the register set for this device - - Example Discovery MPP node: - mpp@f000 { - compatible = "marvell,mv64360-mpp"; - reg = <0xf000 0x10>; - }; - - - n) Marvell Discovery GPP (General Purpose Pins) nodes - - Represent the Discovery's GPP hardware - - Required properties: - - compatible : "marvell,mv64360-gpp" - - reg : Offset and length of the register set for this device - - Example Discovery GPP node: - gpp@f000 { - compatible = "marvell,mv64360-gpp"; - reg = <0xf100 0x20>; - }; - - - o) Marvell Discovery PCI host bridge node - - Represents the Discovery's PCI host bridge device. The properties - for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE - 1275-1994. A typical value for the compatible property is - "marvell,mv64360-pci". - - Example Discovery PCI host bridge node - pci@80000000 { - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - device_type = "pci"; - compatible = "marvell,mv64360-pci"; - reg = <0xcf8 0x8>; - ranges = <0x01000000 0x0 0x0 - 0x88000000 0x0 0x01000000 - 0x02000000 0x0 0x80000000 - 0x80000000 0x0 0x08000000>; - bus-range = <0 255>; - clock-frequency = <66000000>; - interrupt-parent = <&PIC>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = < - /* IDSEL 0x0a */ - 0x5000 0 0 1 &PIC 80 - 0x5000 0 0 2 &PIC 81 - 0x5000 0 0 3 &PIC 91 - 0x5000 0 0 4 &PIC 93 - - /* IDSEL 0x0b */ - 0x5800 0 0 1 &PIC 91 - 0x5800 0 0 2 &PIC 93 - 0x5800 0 0 3 &PIC 80 - 0x5800 0 0 4 &PIC 81 - - /* IDSEL 0x0c */ - 0x6000 0 0 1 &PIC 91 - 0x6000 0 0 2 &PIC 93 - 0x6000 0 0 3 &PIC 80 - 0x6000 0 0 4 &PIC 81 - - /* IDSEL 0x0d */ - 0x6800 0 0 1 &PIC 93 - 0x6800 0 0 2 &PIC 80 - 0x6800 0 0 3 &PIC 81 - 0x6800 0 0 4 &PIC 91 - >; - }; - - - p) Marvell Discovery CPU Error nodes - - Represent the Discovery's CPU error handler device. - - Required properties: - - compatible : "marvell,mv64360-cpu-error" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery CPU Error node: - cpu-error@0070 { - compatible = "marvell,mv64360-cpu-error"; - reg = <0x70 0x10 0x128 0x28>; - interrupts = <3>; - interrupt-parent = <&PIC>; - }; - - - q) Marvell Discovery SRAM Controller nodes - - Represent the Discovery's SRAM controller device. - - Required properties: - - compatible : "marvell,mv64360-sram-ctrl" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery SRAM Controller node: - sram-ctrl@0380 { - compatible = "marvell,mv64360-sram-ctrl"; - reg = <0x380 0x80>; - interrupts = <13>; - interrupt-parent = <&PIC>; - }; - - - r) Marvell Discovery PCI Error Handler nodes - - Represent the Discovery's PCI error handler device. - - Required properties: - - compatible : "marvell,mv64360-pci-error" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery PCI Error Handler node: - pci-error@1d40 { - compatible = "marvell,mv64360-pci-error"; - reg = <0x1d40 0x40 0xc28 0x4>; - interrupts = <12>; - interrupt-parent = <&PIC>; - }; - - - s) Marvell Discovery Memory Controller nodes - - Represent the Discovery's memory controller device. - - Required properties: - - compatible : "marvell,mv64360-mem-ctrl" - - reg : Offset and length of the register set for this device - - interrupts : the interrupt number for this device - - interrupt-parent : the phandle for the interrupt controller - that services interrupts for this device. - - Example Discovery Memory Controller node: - mem-ctrl@1400 { - compatible = "marvell,mv64360-mem-ctrl"; - reg = <0x1400 0x60>; - interrupts = <17>; - interrupt-parent = <&PIC>; - }; - - diff --git a/Documentation/powerpc/dts-bindings/mmc-spi-slot.txt b/Documentation/powerpc/dts-bindings/mmc-spi-slot.txt deleted file mode 100644 index c39ac289195..00000000000 --- a/Documentation/powerpc/dts-bindings/mmc-spi-slot.txt +++ /dev/null @@ -1,23 +0,0 @@ -MMC/SD/SDIO slot directly connected to a SPI bus - -Required properties: -- compatible : should be "mmc-spi-slot". -- reg : should specify SPI address (chip-select number). -- spi-max-frequency : maximum frequency for this device (Hz). -- voltage-ranges : two cells are required, first cell specifies minimum - slot voltage (mV), second cell specifies maximum slot voltage (mV). - Several ranges could be specified. -- gpios : (optional) may specify GPIOs in this order: Card-Detect GPIO, - Write-Protect GPIO. - -Example: - - mmc-slot@0 { - compatible = "fsl,mpc8323rdb-mmc-slot", - "mmc-spi-slot"; - reg = <0>; - gpios = <&qe_pio_d 14 1 - &qe_pio_d 15 0>; - voltage-ranges = <3300 3300>; - spi-max-frequency = <50000000>; - }; diff --git a/Documentation/powerpc/dts-bindings/mtd-physmap.txt b/Documentation/powerpc/dts-bindings/mtd-physmap.txt deleted file mode 100644 index 80152cb567d..00000000000 --- a/Documentation/powerpc/dts-bindings/mtd-physmap.txt +++ /dev/null @@ -1,90 +0,0 @@ -CFI or JEDEC memory-mapped NOR flash, MTD-RAM (NVRAM...) - -Flash chips (Memory Technology Devices) are often used for solid state -file systems on embedded devices. - - - compatible : should contain the specific model of mtd chip(s) - used, if known, followed by either "cfi-flash", "jedec-flash" - or "mtd-ram". - - reg : Address range(s) of the mtd chip(s) - It's possible to (optionally) define multiple "reg" tuples so that - non-identical chips can be described in one node. - - bank-width : Width (in bytes) of the bank. Equal to the - device width times the number of interleaved chips. - - device-width : (optional) Width of a single mtd chip. If - omitted, assumed to be equal to 'bank-width'. - - #address-cells, #size-cells : Must be present if the device has - sub-nodes representing partitions (see below). In this case - both #address-cells and #size-cells must be equal to 1. - -For JEDEC compatible devices, the following additional properties -are defined: - - - vendor-id : Contains the flash chip's vendor id (1 byte). - - device-id : Contains the flash chip's device id (1 byte). - -In addition to the information on the mtd bank itself, the -device tree may optionally contain additional information -describing partitions of the address space. This can be -used on platforms which have strong conventions about which -portions of a flash are used for what purposes, but which don't -use an on-flash partition table such as RedBoot. - -Each partition is represented as a sub-node of the mtd device. -Each node's name represents the name of the corresponding -partition of the mtd device. - -Flash partitions - - reg : The partition's offset and size within the mtd bank. - - label : (optional) The label / name for this partition. - If omitted, the label is taken from the node name (excluding - the unit address). - - read-only : (optional) This parameter, if present, is a hint to - Linux that this partition should only be mounted - read-only. This is usually used for flash partitions - containing early-boot firmware images or data which should not - be clobbered. - -Example: - - flash@ff000000 { - compatible = "amd,am29lv128ml", "cfi-flash"; - reg = <ff000000 01000000>; - bank-width = <4>; - device-width = <1>; - #address-cells = <1>; - #size-cells = <1>; - fs@0 { - label = "fs"; - reg = <0 f80000>; - }; - firmware@f80000 { - label ="firmware"; - reg = <f80000 80000>; - read-only; - }; - }; - -Here an example with multiple "reg" tuples: - - flash@f0000000,0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "intel,PC48F4400P0VB", "cfi-flash"; - reg = <0 0x00000000 0x02000000 - 0 0x02000000 0x02000000>; - bank-width = <2>; - partition@0 { - label = "test-part1"; - reg = <0 0x04000000>; - }; - }; - -An example using SRAM: - - sram@2,0 { - compatible = "samsung,k6f1616u6a", "mtd-ram"; - reg = <2 0 0x00200000>; - bank-width = <2>; - }; - diff --git a/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt b/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt deleted file mode 100644 index b558585b1aa..00000000000 --- a/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt +++ /dev/null @@ -1,109 +0,0 @@ - -Nintendo GameCube device tree -============================= - -1) The "flipper" node - - This node represents the multi-function "Flipper" chip, which packages - many of the devices found in the Nintendo GameCube. - - Required properties: - - - compatible : Should be "nintendo,flipper" - -1.a) The Video Interface (VI) node - - Represents the interface between the graphics processor and a external - video encoder. - - Required properties: - - - compatible : should be "nintendo,flipper-vi" - - reg : should contain the VI registers location and length - - interrupts : should contain the VI interrupt - -1.b) The Processor Interface (PI) node - - Represents the data and control interface between the main processor - and graphics and audio processor. - - Required properties: - - - compatible : should be "nintendo,flipper-pi" - - reg : should contain the PI registers location and length - -1.b.i) The "Flipper" interrupt controller node - - Represents the interrupt controller within the "Flipper" chip. - The node for the "Flipper" interrupt controller must be placed under - the PI node. - - Required properties: - - - compatible : should be "nintendo,flipper-pic" - -1.c) The Digital Signal Procesor (DSP) node - - Represents the digital signal processor interface, designed to offload - audio related tasks. - - Required properties: - - - compatible : should be "nintendo,flipper-dsp" - - reg : should contain the DSP registers location and length - - interrupts : should contain the DSP interrupt - -1.c.i) The Auxiliary RAM (ARAM) node - - Represents the non cpu-addressable ram designed mainly to store audio - related information. - The ARAM node must be placed under the DSP node. - - Required properties: - - - compatible : should be "nintendo,flipper-aram" - - reg : should contain the ARAM start (zero-based) and length - -1.d) The Disk Interface (DI) node - - Represents the interface used to communicate with mass storage devices. - - Required properties: - - - compatible : should be "nintendo,flipper-di" - - reg : should contain the DI registers location and length - - interrupts : should contain the DI interrupt - -1.e) The Audio Interface (AI) node - - Represents the interface to the external 16-bit stereo digital-to-analog - converter. - - Required properties: - - - compatible : should be "nintendo,flipper-ai" - - reg : should contain the AI registers location and length - - interrupts : should contain the AI interrupt - -1.f) The Serial Interface (SI) node - - Represents the interface to the four single bit serial interfaces. - The SI is a proprietary serial interface used normally to control gamepads. - It's NOT a RS232-type interface. - - Required properties: - - - compatible : should be "nintendo,flipper-si" - - reg : should contain the SI registers location and length - - interrupts : should contain the SI interrupt - -1.g) The External Interface (EXI) node - - Represents the multi-channel SPI-like interface. - - Required properties: - - - compatible : should be "nintendo,flipper-exi" - - reg : should contain the EXI registers location and length - - interrupts : should contain the EXI interrupt - diff --git a/Documentation/powerpc/dts-bindings/nintendo/wii.txt b/Documentation/powerpc/dts-bindings/nintendo/wii.txt deleted file mode 100644 index a7e155a023b..00000000000 --- a/Documentation/powerpc/dts-bindings/nintendo/wii.txt +++ /dev/null @@ -1,184 +0,0 @@ - -Nintendo Wii device tree -======================== - -0) The root node - - This node represents the Nintendo Wii video game console. - - Required properties: - - - model : Should be "nintendo,wii" - - compatible : Should be "nintendo,wii" - -1) The "hollywood" node - - This node represents the multi-function "Hollywood" chip, which packages - many of the devices found in the Nintendo Wii. - - Required properties: - - - compatible : Should be "nintendo,hollywood" - -1.a) The Video Interface (VI) node - - Represents the interface between the graphics processor and a external - video encoder. - - Required properties: - - - compatible : should be "nintendo,hollywood-vi","nintendo,flipper-vi" - - reg : should contain the VI registers location and length - - interrupts : should contain the VI interrupt - -1.b) The Processor Interface (PI) node - - Represents the data and control interface between the main processor - and graphics and audio processor. - - Required properties: - - - compatible : should be "nintendo,hollywood-pi","nintendo,flipper-pi" - - reg : should contain the PI registers location and length - -1.b.i) The "Flipper" interrupt controller node - - Represents the "Flipper" interrupt controller within the "Hollywood" chip. - The node for the "Flipper" interrupt controller must be placed under - the PI node. - - Required properties: - - - #interrupt-cells : <1> - - compatible : should be "nintendo,flipper-pic" - - interrupt-controller - -1.c) The Digital Signal Procesor (DSP) node - - Represents the digital signal processor interface, designed to offload - audio related tasks. - - Required properties: - - - compatible : should be "nintendo,hollywood-dsp","nintendo,flipper-dsp" - - reg : should contain the DSP registers location and length - - interrupts : should contain the DSP interrupt - -1.d) The Serial Interface (SI) node - - Represents the interface to the four single bit serial interfaces. - The SI is a proprietary serial interface used normally to control gamepads. - It's NOT a RS232-type interface. - - Required properties: - - - compatible : should be "nintendo,hollywood-si","nintendo,flipper-si" - - reg : should contain the SI registers location and length - - interrupts : should contain the SI interrupt - -1.e) The Audio Interface (AI) node - - Represents the interface to the external 16-bit stereo digital-to-analog - converter. - - Required properties: - - - compatible : should be "nintendo,hollywood-ai","nintendo,flipper-ai" - - reg : should contain the AI registers location and length - - interrupts : should contain the AI interrupt - -1.f) The External Interface (EXI) node - - Represents the multi-channel SPI-like interface. - - Required properties: - - - compatible : should be "nintendo,hollywood-exi","nintendo,flipper-exi" - - reg : should contain the EXI registers location and length - - interrupts : should contain the EXI interrupt - -1.g) The Open Host Controller Interface (OHCI) nodes - - Represent the USB 1.x Open Host Controller Interfaces. - - Required properties: - - - compatible : should be "nintendo,hollywood-usb-ohci","usb-ohci" - - reg : should contain the OHCI registers location and length - - interrupts : should contain the OHCI interrupt - -1.h) The Enhanced Host Controller Interface (EHCI) node - - Represents the USB 2.0 Enhanced Host Controller Interface. - - Required properties: - - - compatible : should be "nintendo,hollywood-usb-ehci","usb-ehci" - - reg : should contain the EHCI registers location and length - - interrupts : should contain the EHCI interrupt - -1.i) The Secure Digital Host Controller Interface (SDHCI) nodes - - Represent the Secure Digital Host Controller Interfaces. - - Required properties: - - - compatible : should be "nintendo,hollywood-sdhci","sdhci" - - reg : should contain the SDHCI registers location and length - - interrupts : should contain the SDHCI interrupt - -1.j) The Inter-Processsor Communication (IPC) node - - Represent the Inter-Processor Communication interface. This interface - enables communications between the Broadway and the Starlet processors. - - - compatible : should be "nintendo,hollywood-ipc" - - reg : should contain the IPC registers location and length - - interrupts : should contain the IPC interrupt - -1.k) The "Hollywood" interrupt controller node - - Represents the "Hollywood" interrupt controller within the - "Hollywood" chip. - - Required properties: - - - #interrupt-cells : <1> - - compatible : should be "nintendo,hollywood-pic" - - reg : should contain the controller registers location and length - - interrupt-controller - - interrupts : should contain the cascade interrupt of the "flipper" pic - - interrupt-parent: should contain the phandle of the "flipper" pic - -1.l) The General Purpose I/O (GPIO) controller node - - Represents the dual access 32 GPIO controller interface. - - Required properties: - - - #gpio-cells : <2> - - compatible : should be "nintendo,hollywood-gpio" - - reg : should contain the IPC registers location and length - - gpio-controller - -1.m) The control node - - Represents the control interface used to setup several miscellaneous - settings of the "Hollywood" chip like boot memory mappings, resets, - disk interface mode, etc. - - Required properties: - - - compatible : should be "nintendo,hollywood-control" - - reg : should contain the control registers location and length - -1.n) The Disk Interface (DI) node - - Represents the interface used to communicate with mass storage devices. - - Required properties: - - - compatible : should be "nintendo,hollywood-di" - - reg : should contain the DI registers location and length - - interrupts : should contain the DI interrupt - diff --git a/Documentation/powerpc/dts-bindings/phy.txt b/Documentation/powerpc/dts-bindings/phy.txt deleted file mode 100644 index bb8c742eb8c..00000000000 --- a/Documentation/powerpc/dts-bindings/phy.txt +++ /dev/null @@ -1,25 +0,0 @@ -PHY nodes - -Required properties: - - - device_type : Should be "ethernet-phy" - - interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - reg : The ID number for the phy, usually a small integer - - linux,phandle : phandle for this node; likely referenced by an - ethernet controller node. - -Example: - -ethernet-phy@0 { - linux,phandle = <2452000> - interrupt-parent = <40000>; - interrupts = <35 1>; - reg = <0>; - device_type = "ethernet-phy"; -}; diff --git a/Documentation/powerpc/dts-bindings/spi-bus.txt b/Documentation/powerpc/dts-bindings/spi-bus.txt deleted file mode 100644 index e782add2e45..00000000000 --- a/Documentation/powerpc/dts-bindings/spi-bus.txt +++ /dev/null @@ -1,57 +0,0 @@ -SPI (Serial Peripheral Interface) busses - -SPI busses can be described with a node for the SPI master device -and a set of child nodes for each SPI slave on the bus. For this -discussion, it is assumed that the system's SPI controller is in -SPI master mode. This binding does not describe SPI controllers -in slave mode. - -The SPI master node requires the following properties: -- #address-cells - number of cells required to define a chip select - address on the SPI bus. -- #size-cells - should be zero. -- compatible - name of SPI bus controller following generic names - recommended practice. -No other properties are required in the SPI bus node. It is assumed -that a driver for an SPI bus device will understand that it is an SPI bus. -However, the binding does not attempt to define the specific method for -assigning chip select numbers. Since SPI chip select configuration is -flexible and non-standardized, it is left out of this binding with the -assumption that board specific platform code will be used to manage -chip selects. Individual drivers can define additional properties to -support describing the chip select layout. - -SPI slave nodes must be children of the SPI master node and can -contain the following properties. -- reg - (required) chip select address of device. -- compatible - (required) name of SPI device following generic names - recommended practice -- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz -- spi-cpol - (optional) Empty property indicating device requires - inverse clock polarity (CPOL) mode -- spi-cpha - (optional) Empty property indicating device requires - shifted clock phase (CPHA) mode -- spi-cs-high - (optional) Empty property indicating device requires - chip select active high - -SPI example for an MPC5200 SPI bus: - spi@f00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - interrupt-parent = <&mpc5200_pic>; - - ethernet-switch@0 { - compatible = "micrel,ks8995m"; - spi-max-frequency = <1000000>; - reg = <0>; - }; - - codec@1 { - compatible = "ti,tlv320aic26"; - spi-max-frequency = <100000>; - reg = <1>; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/usb-ehci.txt b/Documentation/powerpc/dts-bindings/usb-ehci.txt deleted file mode 100644 index fa18612f757..00000000000 --- a/Documentation/powerpc/dts-bindings/usb-ehci.txt +++ /dev/null @@ -1,25 +0,0 @@ -USB EHCI controllers - -Required properties: - - compatible : should be "usb-ehci". - - reg : should contain at least address and length of the standard EHCI - register set for the device. Optional platform-dependent registers - (debug-port or other) can be also specified here, but only after - definition of standard EHCI registers. - - interrupts : one EHCI interrupt should be described here. -If device registers are implemented in big endian mode, the device -node should have "big-endian-regs" property. -If controller implementation operates with big endian descriptors, -"big-endian-desc" property should be specified. -If both big endian registers and descriptors are used by the controller -implementation, "big-endian" property can be specified instead of having -both "big-endian-regs" and "big-endian-desc". - -Example (Sequoia 440EPx): - ehci@e0000300 { - compatible = "ibm,usb-ehci-440epx", "usb-ehci"; - interrupt-parent = <&UIC0>; - interrupts = <1a 4>; - reg = <0 e0000300 90 0 e0000390 70>; - big-endian; - }; diff --git a/Documentation/powerpc/dts-bindings/xilinx.txt b/Documentation/powerpc/dts-bindings/xilinx.txt deleted file mode 100644 index 299d0923537..00000000000 --- a/Documentation/powerpc/dts-bindings/xilinx.txt +++ /dev/null @@ -1,306 +0,0 @@ - d) Xilinx IP cores - - The Xilinx EDK toolchain ships with a set of IP cores (devices) for use - in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range - of standard device types (network, serial, etc.) and miscellaneous - devices (gpio, LCD, spi, etc). Also, since these devices are - implemented within the fpga fabric every instance of the device can be - synthesised with different options that change the behaviour. - - Each IP-core has a set of parameters which the FPGA designer can use to - control how the core is synthesized. Historically, the EDK tool would - extract the device parameters relevant to device drivers and copy them - into an 'xparameters.h' in the form of #define symbols. This tells the - device drivers how the IP cores are configured, but it requires the kernel - to be recompiled every time the FPGA bitstream is resynthesized. - - The new approach is to export the parameters into the device tree and - generate a new device tree each time the FPGA bitstream changes. The - parameters which used to be exported as #defines will now become - properties of the device node. In general, device nodes for IP-cores - will take the following form: - - (name): (generic-name)@(base-address) { - compatible = "xlnx,(ip-core-name)-(HW_VER)" - [, (list of compatible devices), ...]; - reg = <(baseaddr) (size)>; - interrupt-parent = <&interrupt-controller-phandle>; - interrupts = < ... >; - xlnx,(parameter1) = "(string-value)"; - xlnx,(parameter2) = <(int-value)>; - }; - - (generic-name): an open firmware-style name that describes the - generic class of device. Preferably, this is one word, such - as 'serial' or 'ethernet'. - (ip-core-name): the name of the ip block (given after the BEGIN - directive in system.mhs). Should be in lowercase - and all underscores '_' converted to dashes '-'. - (name): is derived from the "PARAMETER INSTANCE" value. - (parameter#): C_* parameters from system.mhs. The C_ prefix is - dropped from the parameter name, the name is converted - to lowercase and all underscore '_' characters are - converted to dashes '-'. - (baseaddr): the baseaddr parameter value (often named C_BASEADDR). - (HW_VER): from the HW_VER parameter. - (size): the address range size (often C_HIGHADDR - C_BASEADDR + 1). - - Typically, the compatible list will include the exact IP core version - followed by an older IP core version which implements the same - interface or any other device with the same interface. - - 'reg', 'interrupt-parent' and 'interrupts' are all optional properties. - - For example, the following block from system.mhs: - - BEGIN opb_uartlite - PARAMETER INSTANCE = opb_uartlite_0 - PARAMETER HW_VER = 1.00.b - PARAMETER C_BAUDRATE = 115200 - PARAMETER C_DATA_BITS = 8 - PARAMETER C_ODD_PARITY = 0 - PARAMETER C_USE_PARITY = 0 - PARAMETER C_CLK_FREQ = 50000000 - PARAMETER C_BASEADDR = 0xEC100000 - PARAMETER C_HIGHADDR = 0xEC10FFFF - BUS_INTERFACE SOPB = opb_7 - PORT OPB_Clk = CLK_50MHz - PORT Interrupt = opb_uartlite_0_Interrupt - PORT RX = opb_uartlite_0_RX - PORT TX = opb_uartlite_0_TX - PORT OPB_Rst = sys_bus_reset_0 - END - - becomes the following device tree node: - - opb_uartlite_0: serial@ec100000 { - device_type = "serial"; - compatible = "xlnx,opb-uartlite-1.00.b"; - reg = <ec100000 10000>; - interrupt-parent = <&opb_intc_0>; - interrupts = <1 0>; // got this from the opb_intc parameters - current-speed = <d#115200>; // standard serial device prop - clock-frequency = <d#50000000>; // standard serial device prop - xlnx,data-bits = <8>; - xlnx,odd-parity = <0>; - xlnx,use-parity = <0>; - }; - - Some IP cores actually implement 2 or more logical devices. In - this case, the device should still describe the whole IP core with - a single node and add a child node for each logical device. The - ranges property can be used to translate from parent IP-core to the - registers of each device. In addition, the parent node should be - compatible with the bus type 'xlnx,compound', and should contain - #address-cells and #size-cells, as with any other bus. (Note: this - makes the assumption that both logical devices have the same bus - binding. If this is not true, then separate nodes should be used - for each logical device). The 'cell-index' property can be used to - enumerate logical devices within an IP core. For example, the - following is the system.mhs entry for the dual ps2 controller found - on the ml403 reference design. - - BEGIN opb_ps2_dual_ref - PARAMETER INSTANCE = opb_ps2_dual_ref_0 - PARAMETER HW_VER = 1.00.a - PARAMETER C_BASEADDR = 0xA9000000 - PARAMETER C_HIGHADDR = 0xA9001FFF - BUS_INTERFACE SOPB = opb_v20_0 - PORT Sys_Intr1 = ps2_1_intr - PORT Sys_Intr2 = ps2_2_intr - PORT Clkin1 = ps2_clk_rx_1 - PORT Clkin2 = ps2_clk_rx_2 - PORT Clkpd1 = ps2_clk_tx_1 - PORT Clkpd2 = ps2_clk_tx_2 - PORT Rx1 = ps2_d_rx_1 - PORT Rx2 = ps2_d_rx_2 - PORT Txpd1 = ps2_d_tx_1 - PORT Txpd2 = ps2_d_tx_2 - END - - It would result in the following device tree nodes: - - opb_ps2_dual_ref_0: opb-ps2-dual-ref@a9000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "xlnx,compound"; - ranges = <0 a9000000 2000>; - // If this device had extra parameters, then they would - // go here. - ps2@0 { - compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; - reg = <0 40>; - interrupt-parent = <&opb_intc_0>; - interrupts = <3 0>; - cell-index = <0>; - }; - ps2@1000 { - compatible = "xlnx,opb-ps2-dual-ref-1.00.a"; - reg = <1000 40>; - interrupt-parent = <&opb_intc_0>; - interrupts = <3 0>; - cell-index = <0>; - }; - }; - - Also, the system.mhs file defines bus attachments from the processor - to the devices. The device tree structure should reflect the bus - attachments. Again an example; this system.mhs fragment: - - BEGIN ppc405_virtex4 - PARAMETER INSTANCE = ppc405_0 - PARAMETER HW_VER = 1.01.a - BUS_INTERFACE DPLB = plb_v34_0 - BUS_INTERFACE IPLB = plb_v34_0 - END - - BEGIN opb_intc - PARAMETER INSTANCE = opb_intc_0 - PARAMETER HW_VER = 1.00.c - PARAMETER C_BASEADDR = 0xD1000FC0 - PARAMETER C_HIGHADDR = 0xD1000FDF - BUS_INTERFACE SOPB = opb_v20_0 - END - - BEGIN opb_uart16550 - PARAMETER INSTANCE = opb_uart16550_0 - PARAMETER HW_VER = 1.00.d - PARAMETER C_BASEADDR = 0xa0000000 - PARAMETER C_HIGHADDR = 0xa0001FFF - BUS_INTERFACE SOPB = opb_v20_0 - END - - BEGIN plb_v34 - PARAMETER INSTANCE = plb_v34_0 - PARAMETER HW_VER = 1.02.a - END - - BEGIN plb_bram_if_cntlr - PARAMETER INSTANCE = plb_bram_if_cntlr_0 - PARAMETER HW_VER = 1.00.b - PARAMETER C_BASEADDR = 0xFFFF0000 - PARAMETER C_HIGHADDR = 0xFFFFFFFF - BUS_INTERFACE SPLB = plb_v34_0 - END - - BEGIN plb2opb_bridge - PARAMETER INSTANCE = plb2opb_bridge_0 - PARAMETER HW_VER = 1.01.a - PARAMETER C_RNG0_BASEADDR = 0x20000000 - PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF - PARAMETER C_RNG1_BASEADDR = 0x60000000 - PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF - PARAMETER C_RNG2_BASEADDR = 0x80000000 - PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF - PARAMETER C_RNG3_BASEADDR = 0xC0000000 - PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF - BUS_INTERFACE SPLB = plb_v34_0 - BUS_INTERFACE MOPB = opb_v20_0 - END - - Gives this device tree (some properties removed for clarity): - - plb@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "xlnx,plb-v34-1.02.a"; - device_type = "ibm,plb"; - ranges; // 1:1 translation - - plb_bram_if_cntrl_0: bram@ffff0000 { - reg = <ffff0000 10000>; - } - - opb@20000000 { - #address-cells = <1>; - #size-cells = <1>; - ranges = <20000000 20000000 20000000 - 60000000 60000000 20000000 - 80000000 80000000 40000000 - c0000000 c0000000 20000000>; - - opb_uart16550_0: serial@a0000000 { - reg = <a00000000 2000>; - }; - - opb_intc_0: interrupt-controller@d1000fc0 { - reg = <d1000fc0 20>; - }; - }; - }; - - That covers the general approach to binding xilinx IP cores into the - device tree. The following are bindings for specific devices: - - i) Xilinx ML300 Framebuffer - - Simple framebuffer device from the ML300 reference design (also on the - ML403 reference design as well as others). - - Optional properties: - - resolution = <xres yres> : pixel resolution of framebuffer. Some - implementations use a different resolution. - Default is <d#640 d#480> - - virt-resolution = <xvirt yvirt> : Size of framebuffer in memory. - Default is <d#1024 d#480>. - - rotate-display (empty) : rotate display 180 degrees. - - ii) Xilinx SystemACE - - The Xilinx SystemACE device is used to program FPGAs from an FPGA - bitstream stored on a CF card. It can also be used as a generic CF - interface device. - - Optional properties: - - 8-bit (empty) : Set this property for SystemACE in 8 bit mode - - iii) Xilinx EMAC and Xilinx TEMAC - - Xilinx Ethernet devices. In addition to general xilinx properties - listed above, nodes for these devices should include a phy-handle - property, and may include other common network device properties - like local-mac-address. - - iv) Xilinx Uartlite - - Xilinx uartlite devices are simple fixed speed serial ports. - - Required properties: - - current-speed : Baud rate of uartlite - - v) Xilinx hwicap - - Xilinx hwicap devices provide access to the configuration logic - of the FPGA through the Internal Configuration Access Port - (ICAP). The ICAP enables partial reconfiguration of the FPGA, - readback of the configuration information, and some control over - 'warm boots' of the FPGA fabric. - - Required properties: - - xlnx,family : The family of the FPGA, necessary since the - capabilities of the underlying ICAP hardware - differ between different families. May be - 'virtex2p', 'virtex4', or 'virtex5'. - - vi) Xilinx Uart 16550 - - Xilinx UART 16550 devices are very similar to the NS16550 but with - different register spacing and an offset from the base address. - - Required properties: - - clock-frequency : Frequency of the clock input - - reg-offset : A value of 3 is required - - reg-shift : A value of 2 is required - - vii) Xilinx USB Host controller - - The Xilinx USB host controller is EHCI compatible but with a different - base address for the EHCI registers, and it is always a big-endian - USB Host controller. The hardware can be configured as high speed only, - or high speed/full speed hybrid. - - Required properties: - - xlnx,support-usb-fs: A value 0 means the core is built as high speed - only. A value 1 means the core also supports - full speed devices. - |