diff options
Diffstat (limited to 'Documentation/powerpc')
| -rw-r--r-- | Documentation/powerpc/booting-without-of.txt | 6 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/4xx/cpm.txt | 52 | ||||
| -rw-r--r-- | Documentation/powerpc/dts-bindings/eeprom.txt | 28 |
3 files changed, 83 insertions, 3 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index 302db5da49b..7400d7555dc 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -131,7 +131,7 @@ order to avoid the degeneration that had become the ppc32 kernel entry point and the way a new platform should be added to the kernel. The legacy iSeries platform breaks those rules as it predates this scheme, but no new board support will be accepted in the main tree that -doesn't follows them properly. In addition, since the advent of the +doesn't follow them properly. In addition, since the advent of the arch/powerpc merged architecture for ppc32 and ppc64, new 32-bit platforms and 32-bit platforms which move into arch/powerpc will be required to use these rules as well. @@ -1025,7 +1025,7 @@ dtc source code can be found at WARNING: This version is still in early development stage; the resulting device-tree "blobs" have not yet been validated with the -kernel. The current generated bloc lacks a useful reserve map (it will +kernel. The current generated block lacks a useful reserve map (it will be fixed to generate an empty one, it's up to the bootloader to fill it up) among others. The error handling needs work, bugs are lurking, etc... @@ -1098,7 +1098,7 @@ supported currently at the toplevel. * an arbitrary array of bytes */ - childnode@addresss { /* define a child node named "childnode" + childnode@address { /* define a child node named "childnode" * whose unit name is "childnode at * address" */ diff --git a/Documentation/powerpc/dts-bindings/4xx/cpm.txt b/Documentation/powerpc/dts-bindings/4xx/cpm.txt new file mode 100644 index 00000000000..ee459806d35 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/4xx/cpm.txt @@ -0,0 +1,52 @@ +PPC4xx Clock Power Management (CPM) node + +Required properties: + - compatible : compatible list, currently only "ibm,cpm" + - dcr-access-method : "native" + - dcr-reg : < DCR register range > + +Optional properties: + - er-offset : All 4xx SoCs with a CPM controller have + one of two different order for the CPM + registers. Some have the CPM registers + in the following order (ER,FR,SR). The + others have them in the following order + (SR,ER,FR). For the second case set + er-offset = <1>. + - unused-units : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set to turn off unused + devices. + - idle-doze : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set to turn off unused + devices. This is usually just CPM[CPU]. + - standby : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set on standby and + restored on resume. + - suspend : specifier consist of one cell. For each + bit in the cell, the corresponding bit + in CPM will be set on suspend (mem) and + restored on resume. Note, for standby + and suspend the corresponding bits can + be different or the same. Usually for + standby only class 2 and 3 units are set. + However, the interface does not care. + If they are the same, the additional + power saving will be seeing if support + is available to put the DDR in self + refresh mode and any additional power + saving techniques for the specific SoC. + +Example: + CPM0: cpm { + compatible = "ibm,cpm"; + dcr-access-method = "native"; + dcr-reg = <0x160 0x003>; + er-offset = <0>; + unused-units = <0x00000100>; + idle-doze = <0x02000000>; + standby = <0xfeff0000>; + suspend = <0xfeff791d>; +}; diff --git a/Documentation/powerpc/dts-bindings/eeprom.txt b/Documentation/powerpc/dts-bindings/eeprom.txt new file mode 100644 index 00000000000..4342c10de1b --- /dev/null +++ b/Documentation/powerpc/dts-bindings/eeprom.txt @@ -0,0 +1,28 @@ +EEPROMs (I2C) + +Required properties: + + - compatible : should be "<manufacturer>,<type>" + If there is no specific driver for <manufacturer>, a generic + driver based on <type> is selected. Possible types are: + 24c00, 24c01, 24c02, 24c04, 24c08, 24c16, 24c32, 24c64, + 24c128, 24c256, 24c512, 24c1024, spd + + - reg : the I2C address of the EEPROM + +Optional properties: + + - pagesize : the length of the pagesize for writing. Please consult the + manual of your device, that value varies a lot. A wrong value + may result in data loss! If not specified, a safety value of + '1' is used which will be very slow. + + - read-only: this parameterless property disables writes to the eeprom + +Example: + +eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + pagesize = <32>; +}; |