1 files changed, 0 insertions, 85 deletions
diff --git a/Documentation/sound/oss/CMI8338 b/Documentation/sound/oss/CMI8338
deleted file mode 100644
index 387d058c3f9..00000000000
--- a/Documentation/sound/oss/CMI8338
+++ /dev/null
@@ -1,85 +0,0 @@
-Audio driver for CM8338/CM8738 chips by Chen-Li Tien
-
-
-HARDWARE SUPPORTED
-================================================================================
-C-Media CMI8338
-C-Media CMI8738
-On-board C-Media chips
-
-
-STEPS TO BUILD DRIVER
-================================================================================
-
-  1. Backup the Config.in and Makefile in the sound driver directory
-     (/usr/src/linux/driver/sound).
-     The Configure.help provide help when you config driver in step
-     4, please backup the original one (/usr/src/linux/Document) and
-     copy this file.
-     The cmpci is document for the driver in detail, please copy it
-     to /usr/src/linux/Document/sound so you can refer it. Backup if
-     there is already one.
-
-  2. Extract the tar file by 'tar xvzf cmpci-xx.tar.gz' in the above
-     directory.
-
-  3. Change directory to /usr/src/linux
-
-  4. Config cm8338 driver by 'make menuconfig', 'make config' or
-     'make xconfig' command.
-
-  5. Please select Sound Card (CONFIG_SOUND=m) support and CMPCI
-     driver (CONFIG_SOUND_CMPCI=m) as modules. Resident mode not tested.
-     For driver option, please refer 'DRIVER PARAMETER'
-
-  6. Compile the kernel if necessary.
-
-  7. Compile the modules by 'make modules'.
-
-  8. Install the modules by 'make modules_install'
-
-
-INSTALL DRIVER
-================================================================================
-
-  1. Before first time to run the driver, create module dependency by
-     'depmod -a'
-
-  2. To install the driver manually, enter 'modprobe cmpci'.
-
-  3. Driver installation for various distributions:
-
-    a. Slackware 4.0
-       Add the 'modprobe cmpci' command in your /etc/rc.d/rc.modules
-       file.so you can start the driver automatically each time booting.
-
-    b. Caldera OpenLinux 2.2
-       Use LISA to load the cmpci module.
-
-    c. RedHat 6.0 and S.u.S.E. 6.1
-       Add following command in /etc/conf.modules:
-
-       alias sound cmpci
-
-	also visit http://www.cmedia.com.tw for installation instruction.
-
-DRIVER PARAMETER
-================================================================================
-
-  Some functions for the cm8738 can be configured in Kernel Configuration
-  or modules parameters. Set these parameters to 1 to enable.
-
-  mpuio:	I/O ports base for MPU-401, 0 if disabled.
-  fmio:		I/O ports base for OPL-3, 0 if disabled.
-  spdif_inverse:Inverse the S/PDIF-in signal, this depends on your
-		CD-ROM or DVD-ROM.
-  spdif_loop:   Enable S/PDIF loop, this route S/PDIF-in to S/PDIF-out
-                directly.
-  speakers:     Number of speakers used.
-  use_line_as_rear:Enable this if you want to use line-in as
-                rear-out.
-  use_line_as_bass:Enable this if you want to use line-in as
-                bass-out.
-  joystick:	Enable joystick. You will need to install Linux joystick
-		driver.
-