diff options
Diffstat (limited to 'Documentation/sound')
| -rw-r--r-- | Documentation/sound/alsa/ALSA-Configuration.txt | 4 | ||||
| -rw-r--r-- | Documentation/sound/alsa/HD-Audio-Models.txt | 33 | ||||
| -rw-r--r-- | Documentation/sound/alsa/HD-Audio.txt | 64 |
3 files changed, 92 insertions, 9 deletions
diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt index ea16e7d184a..ad51c93d41e 100644 --- a/Documentation/sound/alsa/ALSA-Configuration.txt +++ b/Documentation/sound/alsa/ALSA-Configuration.txt @@ -788,6 +788,10 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed. bdl_pos_adj - Specifies the DMA IRQ timing delay in samples. Passing -1 will make the driver to choose the appropriate value based on the controller chip. + patch - Specifies the early "patch" files to modify the HD-audio + setup before initializing the codecs. This option is + available only when CONFIG_SND_HDA_PATCH_LOADER=y is set. + See HD-Audio.txt for details. [Single (global) options] single_cmd - Use single immediate commands to communicate with diff --git a/Documentation/sound/alsa/HD-Audio-Models.txt b/Documentation/sound/alsa/HD-Audio-Models.txt index 939a3dd5814..97eebd63bed 100644 --- a/Documentation/sound/alsa/HD-Audio-Models.txt +++ b/Documentation/sound/alsa/HD-Audio-Models.txt @@ -114,8 +114,8 @@ ALC662/663/272 samsung-nc10 Samsung NC10 mini notebook auto auto-config reading BIOS (default) -ALC882/885 -========== +ALC882/883/885/888/889 +====================== 3stack-dig 3-jack with SPDIF I/O 6stack-dig 6-jack digital with SPDIF I/O arima Arima W820Di1 @@ -127,12 +127,8 @@ ALC882/885 mbp3 Macbook Pro rev3 imac24 iMac 24'' with jack detection w2jc ASUS W2JC - auto auto-config reading BIOS (default) - -ALC883/888 -========== - 3stack-dig 3-jack with SPDIF I/O - 6stack-dig 6-jack digital with SPDIF I/O + 3stack-2ch-dig 3-jack with SPDIF I/O (ALC883) + alc883-6stack-dig 6-jack digital with SPDIF I/O (ALC883) 3stack-6ch 3-jack 6-channel 3stack-6ch-dig 3-jack 6-channel with SPDIF I/O 6stack-dig-demo 6-jack digital for Intel demo board @@ -140,6 +136,7 @@ ALC883/888 acer-aspire Acer Aspire 9810 acer-aspire-4930g Acer Aspire 4930G acer-aspire-6530g Acer Aspire 6530G + acer-aspire-7730g Acer Aspire 7730G acer-aspire-8930g Acer Aspire 8930G medion Medion Laptops medion-md2 Medion MD2 @@ -155,10 +152,13 @@ ALC883/888 3stack-hp HP machines with 3stack (Lucknow, Samba boards) 6stack-dell Dell machines with 6stack (Inspiron 530) mitac Mitac 8252D + clevo-m540r Clevo M540R (6ch + digital) clevo-m720 Clevo M720 laptop series fujitsu-pi2515 Fujitsu AMILO Pi2515 fujitsu-xa3530 Fujitsu AMILO XA3530 3stack-6ch-intel Intel DG33* boards + intel-alc889a Intel IbexPeak with ALC889A + intel-x58 Intel DX58 with ALC889 asus-p5q ASUS P5Q-EM boards mb31 MacBook 3,1 sony-vaio-tt Sony VAIO TT @@ -229,7 +229,7 @@ AD1984 ====== basic default configuration thinkpad Lenovo Thinkpad T61/X61 - dell Dell T3400 + dell_desktop Dell T3400 AD1986A ======= @@ -258,6 +258,7 @@ Conexant 5045 laptop-micsense Laptop with Mic sense (old model fujitsu) laptop-hpmicsense Laptop with HP and Mic senses benq Benq R55E + laptop-hp530 HP 530 laptop test for testing/debugging purpose, almost all controls can be adjusted. Appearing only when compiled with $CONFIG_SND_DEBUG=y @@ -278,9 +279,16 @@ Conexant 5051 hp-dv6736 HP dv6736 lenovo-x200 Lenovo X200 laptop +Conexant 5066 +============= + laptop Basic Laptop config (default) + dell-laptop Dell laptops + olpc-xo-1_5 OLPC XO 1.5 + STAC9200 ======== ref Reference board + oqo OQO Model 2 dell-d21 Dell (unknown) dell-d22 Dell (unknown) dell-d23 Dell (unknown) @@ -368,10 +376,12 @@ STAC92HD73* =========== ref Reference board no-jd BIOS setup but without jack-detection + intel Intel DG45* mobos dell-m6-amic Dell desktops/laptops with analog mics dell-m6-dmic Dell desktops/laptops with digital mics dell-m6 Dell desktops/laptops with both type of mics dell-eq Dell desktops/laptops + alienware Alienware M17x auto BIOS setup (default) STAC92HD83* @@ -385,3 +395,8 @@ STAC9872 ======== vaio VAIO laptop without SPDIF auto BIOS setup (default) + +Cirrus Logic CS4206/4207 +======================== + mbp55 MacBook Pro 5,5 + auto BIOS setup (default) diff --git a/Documentation/sound/alsa/HD-Audio.txt b/Documentation/sound/alsa/HD-Audio.txt index 71ac995b191..7b8a5f947d1 100644 --- a/Documentation/sound/alsa/HD-Audio.txt +++ b/Documentation/sound/alsa/HD-Audio.txt @@ -139,6 +139,10 @@ The driver checks PCI SSID and looks through the static configuration table until any matching entry is found. If you have a new machine, you may see a message like below: ------------------------------------------------------------------------ + hda_codec: ALC880: BIOS auto-probing. +------------------------------------------------------------------------ +Meanwhile, in the earlier versions, you would see a message like: +------------------------------------------------------------------------ hda_codec: Unknown model for ALC880, trying auto-probe from BIOS... ------------------------------------------------------------------------ Even if you see such a message, DON'T PANIC. Take a deep breath and @@ -403,6 +407,66 @@ re-configure based on that state, run like below: ------------------------------------------------------------------------ +Early Patching +~~~~~~~~~~~~~~ +When CONFIG_SND_HDA_PATCH_LOADER=y is set, you can pass a "patch" as a +firmware file for modifying the HD-audio setup before initializing the +codec. This can work basically like the reconfiguration via sysfs in +the above, but it does it before the first codec configuration. + +A patch file is a plain text file which looks like below: + +------------------------------------------------------------------------ + [codec] + 0x12345678 0xabcd1234 2 + + [model] + auto + + [pincfg] + 0x12 0x411111f0 + + [verb] + 0x20 0x500 0x03 + 0x20 0x400 0xff + + [hint] + hp_detect = yes +------------------------------------------------------------------------ + +The file needs to have a line `[codec]`. The next line should contain +three numbers indicating the codec vendor-id (0x12345678 in the +example), the codec subsystem-id (0xabcd1234) and the address (2) of +the codec. The rest patch entries are applied to this specified codec +until another codec entry is given. + +The `[model]` line allows to change the model name of the each codec. +In the example above, it will be changed to model=auto. +Note that this overrides the module option. + +After the `[pincfg]` line, the contents are parsed as the initial +default pin-configurations just like `user_pin_configs` sysfs above. +The values can be shown in user_pin_configs sysfs file, too. + +Similarly, the lines after `[verb]` are parsed as `init_verbs` +sysfs entries, and the lines after `[hint]` are parsed as `hints` +sysfs entries, respectively. + +The hd-audio driver reads the file via request_firmware(). Thus, +a patch file has to be located on the appropriate firmware path, +typically, /lib/firmware. For example, when you pass the option +`patch=hda-init.fw`, the file /lib/firmware/hda-init-fw must be +present. + +The patch module option is specific to each card instance, and you +need to give one file name for each instance, separated by commas. +For example, if you have two cards, one for an on-board analog and one +for an HDMI video board, you may pass patch option like below: +------------------------------------------------------------------------ + options snd-hda-intel patch=on-board-patch,hdmi-patch +------------------------------------------------------------------------ + + Power-Saving ~~~~~~~~~~~~ The power-saving is a kind of auto-suspend of the device. When the |