diff options
Diffstat (limited to 'Documentation/video4linux/ibmcam.txt')
| -rw-r--r-- | Documentation/video4linux/ibmcam.txt | 168 |
1 files changed, 84 insertions, 84 deletions
diff --git a/Documentation/video4linux/ibmcam.txt b/Documentation/video4linux/ibmcam.txt index 4a40a2e9945..397a94eb77b 100644 --- a/Documentation/video4linux/ibmcam.txt +++ b/Documentation/video4linux/ibmcam.txt @@ -21,7 +21,7 @@ Internal interface: Video For Linux (V4L) Supported controls: - by V4L: Contrast, Brightness, Color, Hue - by driver options: frame rate, lighting conditions, video format, - default picture settings, sharpness. + default picture settings, sharpness. SUPPORTED CAMERAS: @@ -191,66 +191,66 @@ init_model2_sat Integer 0..255 [0x34] init_model2_sat=65 init_model2_yb Integer 0..255 [0xa0] init_model2_yb=200 debug You don't need this option unless you are a developer. - If you are a developer then you will see in the code - what values do what. 0=off. + If you are a developer then you will see in the code + what values do what. 0=off. flags This is a bit mask, and you can combine any number of - bits to produce what you want. Usually you don't want - any of extra features this option provides: - - FLAGS_RETRY_VIDIOCSYNC 1 This bit allows to retry failed - VIDIOCSYNC ioctls without failing. - Will work with xawtv, will not - with xrealproducer. Default is - not set. - FLAGS_MONOCHROME 2 Activates monochrome (b/w) mode. - FLAGS_DISPLAY_HINTS 4 Shows colored pixels which have - magic meaning to developers. - FLAGS_OVERLAY_STATS 8 Shows tiny numbers on screen, - useful only for debugging. - FLAGS_FORCE_TESTPATTERN 16 Shows blue screen with numbers. - FLAGS_SEPARATE_FRAMES 32 Shows each frame separately, as - it was received from the camera. - Default (not set) is to mix the - preceding frame in to compensate - for occasional loss of Isoc data - on high frame rates. - FLAGS_CLEAN_FRAMES 64 Forces "cleanup" of each frame - prior to use; relevant only if - FLAGS_SEPARATE_FRAMES is set. - Default is not to clean frames, - this is a little faster but may - produce flicker if frame rate is - too high and Isoc data gets lost. - FLAGS_NO_DECODING 128 This flag turns the video stream - decoder off, and dumps the raw - Isoc data from the camera into - the reading process. Useful to - developers, but not to users. + bits to produce what you want. Usually you don't want + any of extra features this option provides: + + FLAGS_RETRY_VIDIOCSYNC 1 This bit allows to retry failed + VIDIOCSYNC ioctls without failing. + Will work with xawtv, will not + with xrealproducer. Default is + not set. + FLAGS_MONOCHROME 2 Activates monochrome (b/w) mode. + FLAGS_DISPLAY_HINTS 4 Shows colored pixels which have + magic meaning to developers. + FLAGS_OVERLAY_STATS 8 Shows tiny numbers on screen, + useful only for debugging. + FLAGS_FORCE_TESTPATTERN 16 Shows blue screen with numbers. + FLAGS_SEPARATE_FRAMES 32 Shows each frame separately, as + it was received from the camera. + Default (not set) is to mix the + preceding frame in to compensate + for occasional loss of Isoc data + on high frame rates. + FLAGS_CLEAN_FRAMES 64 Forces "cleanup" of each frame + prior to use; relevant only if + FLAGS_SEPARATE_FRAMES is set. + Default is not to clean frames, + this is a little faster but may + produce flicker if frame rate is + too high and Isoc data gets lost. + FLAGS_NO_DECODING 128 This flag turns the video stream + decoder off, and dumps the raw + Isoc data from the camera into + the reading process. Useful to + developers, but not to users. framerate This setting controls frame rate of the camera. This is - an approximate setting (in terms of "worst" ... "best") - because camera changes frame rate depending on amount - of light available. Setting 0 is slowest, 6 is fastest. - Beware - fast settings are very demanding and may not - work well with all video sizes. Be conservative. + an approximate setting (in terms of "worst" ... "best") + because camera changes frame rate depending on amount + of light available. Setting 0 is slowest, 6 is fastest. + Beware - fast settings are very demanding and may not + work well with all video sizes. Be conservative. hue_correction This highly optional setting allows to adjust the - hue of the image in a way slightly different from - what usual "hue" control does. Both controls affect - YUV colorspace: regular "hue" control adjusts only - U component, and this "hue_correction" option similarly - adjusts only V component. However usually it is enough - to tweak only U or V to compensate for colored light or - color temperature; this option simply allows more - complicated correction when and if it is necessary. + hue of the image in a way slightly different from + what usual "hue" control does. Both controls affect + YUV colorspace: regular "hue" control adjusts only + U component, and this "hue_correction" option similarly + adjusts only V component. However usually it is enough + to tweak only U or V to compensate for colored light or + color temperature; this option simply allows more + complicated correction when and if it is necessary. init_brightness These settings specify _initial_ values which will be init_contrast used to set up the camera. If your V4L application has init_color its own controls to adjust the picture then these init_hue controls will be used too. These options allow you to - preconfigure the camera when it gets connected, before - any V4L application connects to it. Good for webcams. + preconfigure the camera when it gets connected, before + any V4L application connects to it. Good for webcams. init_model2_rg These initial settings alter color balance of the init_model2_rg2 camera on hardware level. All four settings may be used @@ -258,47 +258,47 @@ init_model2_sat to tune the camera to specific lighting conditions. These init_model2_yb settings only apply to Model 2 cameras. lighting This option selects one of three hardware-defined - photosensitivity settings of the camera. 0=bright light, - 1=Medium (default), 2=Low light. This setting affects - frame rate: the dimmer the lighting the lower the frame - rate (because longer exposition time is needed). The - Model 2 cameras allow values more than 2 for this option, - thus enabling extremely high sensitivity at cost of frame - rate, color saturation and imaging sensor noise. + photosensitivity settings of the camera. 0=bright light, + 1=Medium (default), 2=Low light. This setting affects + frame rate: the dimmer the lighting the lower the frame + rate (because longer exposition time is needed). The + Model 2 cameras allow values more than 2 for this option, + thus enabling extremely high sensitivity at cost of frame + rate, color saturation and imaging sensor noise. sharpness This option controls smoothing (noise reduction) - made by camera. Setting 0 is most smooth, setting 6 - is most sharp. Be aware that CMOS sensor used in the - camera is pretty noisy, so if you choose 6 you will - be greeted with "snowy" image. Default is 4. Model 2 - cameras do not support this feature. + made by camera. Setting 0 is most smooth, setting 6 + is most sharp. Be aware that CMOS sensor used in the + camera is pretty noisy, so if you choose 6 you will + be greeted with "snowy" image. Default is 4. Model 2 + cameras do not support this feature. size This setting chooses one of several image sizes that are - supported by this driver. Cameras may support more, but - it's difficult to reverse-engineer all formats. - Following video sizes are supported: - - size=0 128x96 (Model 1 only) - size=1 160x120 - size=2 176x144 - size=3 320x240 (Model 2 only) - size=4 352x240 (Model 2 only) - size=5 352x288 - size=6 640x480 (Model 3 only) - - The 352x288 is the native size of the Model 1 sensor - array, so it's the best resolution the camera can - yield. The best resolution of Model 2 is 176x144, and - larger images are produced by stretching the bitmap. - Model 3 has sensor with 640x480 grid, and it works too, - but the frame rate will be exceptionally low (1-2 FPS); - it may be still OK for some applications, like security. - Choose the image size you need. The smaller image can - support faster frame rate. Default is 352x288. + supported by this driver. Cameras may support more, but + it's difficult to reverse-engineer all formats. + Following video sizes are supported: + + size=0 128x96 (Model 1 only) + size=1 160x120 + size=2 176x144 + size=3 320x240 (Model 2 only) + size=4 352x240 (Model 2 only) + size=5 352x288 + size=6 640x480 (Model 3 only) + + The 352x288 is the native size of the Model 1 sensor + array, so it's the best resolution the camera can + yield. The best resolution of Model 2 is 176x144, and + larger images are produced by stretching the bitmap. + Model 3 has sensor with 640x480 grid, and it works too, + but the frame rate will be exceptionally low (1-2 FPS); + it may be still OK for some applications, like security. + Choose the image size you need. The smaller image can + support faster frame rate. Default is 352x288. For more information and the Troubleshooting FAQ visit this URL: - http://www.linux-usb.org/ibmcam/ + http://www.linux-usb.org/ibmcam/ WHAT NEEDS TO BE DONE: |