diff options
Diffstat (limited to 'Documentation/virtual/lguest/lguest.txt')
| -rw-r--r-- | Documentation/virtual/lguest/lguest.txt | 129 |
1 files changed, 0 insertions, 129 deletions
diff --git a/Documentation/virtual/lguest/lguest.txt b/Documentation/virtual/lguest/lguest.txt deleted file mode 100644 index bff0c554485..00000000000 --- a/Documentation/virtual/lguest/lguest.txt +++ /dev/null @@ -1,129 +0,0 @@ - __ - (___()'`; Rusty's Remarkably Unreliable Guide to Lguest - /, /` - or, A Young Coder's Illustrated Hypervisor - \\"--\\ http://lguest.ozlabs.org - -Lguest is designed to be a minimal 32-bit x86 hypervisor for the Linux kernel, -for Linux developers and users to experiment with virtualization with the -minimum of complexity. Nonetheless, it should have sufficient features to -make it useful for specific tasks, and, of course, you are encouraged to fork -and enhance it (see drivers/lguest/README). - -Features: - -- Kernel module which runs in a normal kernel. -- Simple I/O model for communication. -- Simple program to create new guests. -- Logo contains cute puppies: http://lguest.ozlabs.org - -Developer features: - -- Fun to hack on. -- No ABI: being tied to a specific kernel anyway, you can change anything. -- Many opportunities for improvement or feature implementation. - -Running Lguest: - -- The easiest way to run lguest is to use same kernel as guest and host. - You can configure them differently, but usually it's easiest not to. - - You will need to configure your kernel with the following options: - - "General setup": - "Prompt for development and/or incomplete code/drivers" = Y - (CONFIG_EXPERIMENTAL=y) - - "Processor type and features": - "Paravirtualized guest support" = Y - "Lguest guest support" = Y - "High Memory Support" = off/4GB - "Alignment value to which kernel should be aligned" = 0x100000 - (CONFIG_PARAVIRT=y, CONFIG_LGUEST_GUEST=y, CONFIG_HIGHMEM64G=n and - CONFIG_PHYSICAL_ALIGN=0x100000) - - "Device Drivers": - "Block devices" - "Virtio block driver (EXPERIMENTAL)" = M/Y - "Network device support" - "Universal TUN/TAP device driver support" = M/Y - "Virtio network driver (EXPERIMENTAL)" = M/Y - (CONFIG_VIRTIO_BLK=m, CONFIG_VIRTIO_NET=m and CONFIG_TUN=m) - - "Virtualization" - "Linux hypervisor example code" = M/Y - (CONFIG_LGUEST=m) - -- A tool called "lguest" is available in this directory: type "make" - to build it. If you didn't build your kernel in-tree, use "make - O=<builddir>". - -- Create or find a root disk image. There are several useful ones - around, such as the xm-test tiny root image at - http://xm-test.xensource.com/ramdisks/initrd-1.1-i386.img - - For more serious work, I usually use a distribution ISO image and - install it under qemu, then make multiple copies: - - dd if=/dev/zero of=rootfile bs=1M count=2048 - qemu -cdrom image.iso -hda rootfile -net user -net nic -boot d - - Make sure that you install a getty on /dev/hvc0 if you want to log in on the - console! - -- "modprobe lg" if you built it as a module. - -- Run an lguest as root: - - Documentation/virtual/lguest/lguest 64 vmlinux --tunnet=192.168.19.1 \ - --block=rootfile root=/dev/vda - - Explanation: - 64: the amount of memory to use, in MB. - - vmlinux: the kernel image found in the top of your build directory. You - can also use a standard bzImage. - - --tunnet=192.168.19.1: configures a "tap" device for networking with this - IP address. - - --block=rootfile: a file or block device which becomes /dev/vda - inside the guest. - - root=/dev/vda: this (and anything else on the command line) are - kernel boot parameters. - -- Configuring networking. I usually have the host masquerade, using - "iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE" and "echo 1 > - /proc/sys/net/ipv4/ip_forward". In this example, I would configure - eth0 inside the guest at 192.168.19.2. - - Another method is to bridge the tap device to an external interface - using --tunnet=bridge:<bridgename>, and perhaps run dhcp on the guest - to obtain an IP address. The bridge needs to be configured first: - this option simply adds the tap interface to it. - - A simple example on my system: - - ifconfig eth0 0.0.0.0 - brctl addbr lg0 - ifconfig lg0 up - brctl addif lg0 eth0 - dhclient lg0 - - Then use --tunnet=bridge:lg0 when launching the guest. - - See: - - http://www.linuxfoundation.org/collaborate/workgroups/networking/bridge - - for general information on how to get bridging to work. - -- Random number generation. Using the --rng option will provide a - /dev/hwrng in the guest that will read from the host's /dev/random. - Use this option in conjunction with rng-tools (see ../hw_random.txt) - to provide entropy to the guest kernel's /dev/random. - -There is a helpful mailing list at http://ozlabs.org/mailman/listinfo/lguest - -Good luck! -Rusty Russell rusty@rustcorp.com.au. |