diff options
Diffstat (limited to 'Documentation')
63 files changed, 1923 insertions, 2436 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-pci b/Documentation/ABI/testing/sysfs-bus-pci index e638e15a889..97ad190e13a 100644 --- a/Documentation/ABI/testing/sysfs-bus-pci +++ b/Documentation/ABI/testing/sysfs-bus-pci @@ -41,6 +41,49 @@ Description: for the device and attempt to bind to it. For example: # echo "8086 10f5" > /sys/bus/pci/drivers/foo/new_id +What: /sys/bus/pci/drivers/.../remove_id +Date: February 2009 +Contact: Chris Wright <chrisw@sous-sol.org> +Description: + Writing a device ID to this file will remove an ID + that was dynamically added via the new_id sysfs entry. + The format for the device ID is: + VVVV DDDD SVVV SDDD CCCC MMMM. That is Vendor ID, Device + ID, Subsystem Vendor ID, Subsystem Device ID, Class, + and Class Mask. The Vendor ID and Device ID fields are + required, the rest are optional. After successfully + removing an ID, the driver will no longer support the + device. This is useful to ensure auto probing won't + match the driver to the device. For example: + # echo "8086 10f5" > /sys/bus/pci/drivers/foo/remove_id + +What: /sys/bus/pci/rescan +Date: January 2009 +Contact: Linux PCI developers <linux-pci@vger.kernel.org> +Description: + Writing a non-zero value to this attribute will + force a rescan of all PCI buses in the system, and + re-discover previously removed devices. + Depends on CONFIG_HOTPLUG. + +What: /sys/bus/pci/devices/.../remove +Date: January 2009 +Contact: Linux PCI developers <linux-pci@vger.kernel.org> +Description: + Writing a non-zero value to this attribute will + hot-remove the PCI device and any of its children. + Depends on CONFIG_HOTPLUG. + +What: /sys/bus/pci/devices/.../rescan +Date: January 2009 +Contact: Linux PCI developers <linux-pci@vger.kernel.org> +Description: + Writing a non-zero value to this attribute will + force a rescan of the device's parent bus and all + child buses, and re-discover devices removed earlier + from this part of the device tree. + Depends on CONFIG_HOTPLUG. + What: /sys/bus/pci/devices/.../vpd Date: February 2008 Contact: Ben Hutchings <bhutchings@solarflare.com> @@ -52,3 +95,30 @@ Description: that some devices may have malformatted data. If the underlying VPD has a writable section then the corresponding section of this file will be writable. + +What: /sys/bus/pci/devices/.../virtfnN +Date: March 2009 +Contact: Yu Zhao <yu.zhao@intel.com> +Description: + This symbolic link appears when hardware supports the SR-IOV + capability and the Physical Function driver has enabled it. + The symbolic link points to the PCI device sysfs entry of the + Virtual Function whose index is N (0...MaxVFs-1). + +What: /sys/bus/pci/devices/.../dep_link +Date: March 2009 +Contact: Yu Zhao <yu.zhao@intel.com> +Description: + This symbolic link appears when hardware supports the SR-IOV + capability and the Physical Function driver has enabled it, + and this device has vendor specific dependencies with others. + The symbolic link points to the PCI device sysfs entry of + Physical Function this device depends on. + +What: /sys/bus/pci/devices/.../physfn +Date: March 2009 +Contact: Yu Zhao <yu.zhao@intel.com> +Description: + This symbolic link appears when a device is a Virtual Function. + The symbolic link points to the PCI device sysfs entry of the + Physical Function this device associates with. diff --git a/Documentation/ABI/testing/sysfs-fs-ext4 b/Documentation/ABI/testing/sysfs-fs-ext4 new file mode 100644 index 00000000000..4e79074de28 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-fs-ext4 @@ -0,0 +1,81 @@ +What: /sys/fs/ext4/<disk>/mb_stats +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + Controls whether the multiblock allocator should + collect statistics, which are shown during the unmount. + 1 means to collect statistics, 0 means not to collect + statistics + +What: /sys/fs/ext4/<disk>/mb_group_prealloc +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + The multiblock allocator will round up allocation + requests to a multiple of this tuning parameter if the + stripe size is not set in the ext4 superblock + +What: /sys/fs/ext4/<disk>/mb_max_to_scan +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + The maximum number of extents the multiblock allocator + will search to find the best extent + +What: /sys/fs/ext4/<disk>/mb_min_to_scan +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + The minimum number of extents the multiblock allocator + will search to find the best extent + +What: /sys/fs/ext4/<disk>/mb_order2_req +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + Tuning parameter which controls the minimum size for + requests (as a power of 2) where the buddy cache is + used + +What: /sys/fs/ext4/<disk>/mb_stream_req +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + Files which have fewer blocks than this tunable + parameter will have their blocks allocated out of a + block group specific preallocation pool, so that small + files are packed closely together. Each large file + will have its blocks allocated out of its own unique + preallocation pool. + +What: /sys/fs/ext4/<disk>/inode_readahead +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + Tuning parameter which controls the maximum number of + inode table blocks that ext4's inode table readahead + algorithm will pre-read into the buffer cache + +What: /sys/fs/ext4/<disk>/delayed_allocation_blocks +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + This file is read-only and shows the number of blocks + that are dirty in the page cache, but which do not + have their location in the filesystem allocated yet. + +What: /sys/fs/ext4/<disk>/lifetime_write_kbytes +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + This file is read-only and shows the number of kilobytes + of data that have been written to this filesystem since it was + created. + +What: /sys/fs/ext4/<disk>/session_write_kbytes +Date: March 2008 +Contact: "Theodore Ts'o" <tytso@mit.edu> +Description: + This file is read-only and shows the number of + kilobytes of data that have been written to this + filesystem since it was mounted. diff --git a/Documentation/DMA-API.txt b/Documentation/DMA-API.txt index 2a3fcc55e98..d9aa43d78bc 100644 --- a/Documentation/DMA-API.txt +++ b/Documentation/DMA-API.txt @@ -609,3 +609,109 @@ size is the size (and should be a page-sized multiple). The return value will be either a pointer to the processor virtual address of the memory, or an error (via PTR_ERR()) if any part of the region is occupied. + +Part III - Debug drivers use of the DMA-API +------------------------------------------- + +The DMA-API as described above as some constraints. DMA addresses must be +released with the corresponding function with the same size for example. With +the advent of hardware IOMMUs it becomes more and more important that drivers +do not violate those constraints. In the worst case such a violation can +result in data corruption up to destroyed filesystems. + +To debug drivers and find bugs in the usage of the DMA-API checking code can +be compiled into the kernel which will tell the developer about those +violations. If your architecture supports it you can select the "Enable +debugging of DMA-API usage" option in your kernel configuration. Enabling this +option has a performance impact. Do not enable it in production kernels. + +If you boot the resulting kernel will contain code which does some bookkeeping +about what DMA memory was allocated for which device. If this code detects an +error it prints a warning message with some details into your kernel log. An +example warning message may look like this: + +------------[ cut here ]------------ +WARNING: at /data2/repos/linux-2.6-iommu/lib/dma-debug.c:448 + check_unmap+0x203/0x490() +Hardware name: +forcedeth 0000:00:08.0: DMA-API: device driver frees DMA memory with wrong + function [device address=0x00000000640444be] [size=66 bytes] [mapped as +single] [unmapped as page] +Modules linked in: nfsd exportfs bridge stp llc r8169 +Pid: 0, comm: swapper Tainted: G W 2.6.28-dmatest-09289-g8bb99c0 #1 +Call Trace: + <IRQ> [<ffffffff80240b22>] warn_slowpath+0xf2/0x130 + [<ffffffff80647b70>] _spin_unlock+0x10/0x30 + [<ffffffff80537e75>] usb_hcd_link_urb_to_ep+0x75/0xc0 + [<ffffffff80647c22>] _spin_unlock_irqrestore+0x12/0x40 + [<ffffffff8055347f>] ohci_urb_enqueue+0x19f/0x7c0 + [<ffffffff80252f96>] queue_work+0x56/0x60 + [<ffffffff80237e10>] enqueue_task_fair+0x20/0x50 + [<ffffffff80539279>] usb_hcd_submit_urb+0x379/0xbc0 + [<ffffffff803b78c3>] cpumask_next_and+0x23/0x40 + [<ffffffff80235177>] find_busiest_group+0x207/0x8a0 + [<ffffffff8064784f>] _spin_lock_irqsave+0x1f/0x50 + [<ffffffff803c7ea3>] check_unmap+0x203/0x490 + [<ffffffff803c8259>] debug_dma_unmap_page+0x49/0x50 + [<ffffffff80485f26>] nv_tx_done_optimized+0xc6/0x2c0 + [<ffffffff80486c13>] nv_nic_irq_optimized+0x73/0x2b0 + [<ffffffff8026df84>] handle_IRQ_event+0x34/0x70 + [<ffffffff8026ffe9>] handle_edge_irq+0xc9/0x150 + [<ffffffff8020e3ab>] do_IRQ+0xcb/0x1c0 + [<ffffffff8020c093>] ret_from_intr+0x0/0xa + <EOI> <4>---[ end trace f6435a98e2a38c0e ]--- + +The driver developer can find the driver and the device including a stacktrace +of the DMA-API call which caused this warning. + +Per default only the first error will result in a warning message. All other +errors will only silently counted. This limitation exist to prevent the code +from flooding your kernel log. To support debugging a device driver this can +be disabled via debugfs. See the debugfs interface documentation below for +details. + +The debugfs directory for the DMA-API debugging code is called dma-api/. In +this directory the following files can currently be found: + + dma-api/all_errors This file contains a numeric value. If this + value is not equal to zero the debugging code + will print a warning for every error it finds + into the kernel log. Be carefull with this + option. It can easily flood your logs. + + dma-api/disabled This read-only file contains the character 'Y' + if the debugging code is disabled. This can + happen when it runs out of memory or if it was + disabled at boot time + + dma-api/error_count This file is read-only and shows the total + numbers of errors found. + + dma-api/num_errors The number in this file shows how many + warnings will be printed to the kernel log + before it stops. This number is initialized to + one at system boot and be set by writing into + this file + + dma-api/min_free_entries + This read-only file can be read to get the + minimum number of free dma_debug_entries the + allocator has ever seen. If this value goes + down to zero the code will disable itself + because it is not longer reliable. + + dma-api/num_free_entries + The current number of free dma_debug_entries + in the allocator. + +If you have this code compiled into your kernel it will be enabled by default. +If you want to boot without the bookkeeping anyway you can provide +'dma_debug=off' as a boot parameter. This will disable DMA-API debugging. +Notice that you can not enable it again at runtime. You have to reboot to do +so. + +When the code disables itself at runtime this is most likely because it ran +out of dma_debug_entries. These entries are preallocated at boot. The number +of preallocated entries is defined per architecture. If it is too low for you +boot with 'dma_debug_entries=<your_desired_number>' to overwrite the +architectural default. diff --git a/Documentation/DocBook/.gitignore b/Documentation/DocBook/.gitignore index c102c02ecf8..c6def352fe3 100644 --- a/Documentation/DocBook/.gitignore +++ b/Documentation/DocBook/.gitignore @@ -4,3 +4,7 @@ *.html *.9.gz *.9 +*.aux +*.dvi +*.log +*.out diff --git a/Documentation/DocBook/kernel-api.tmpl b/Documentation/DocBook/kernel-api.tmpl index bc962cda650..58c194572c7 100644 --- a/Documentation/DocBook/kernel-api.tmpl +++ b/Documentation/DocBook/kernel-api.tmpl @@ -199,6 +199,7 @@ X!Edrivers/pci/hotplug.c --> !Edrivers/pci/probe.c !Edrivers/pci/rom.c +!Edrivers/pci/iov.c </sect1> <sect1><title>PCI Hotplug Support Library</title> !Edrivers/pci/hotplug/pci_hotplug_core.c diff --git a/Documentation/DocBook/procfs_example.c b/Documentation/DocBook/procfs_example.c index 8c6396e4bf3..a5b11793b1e 100644 --- a/Documentation/DocBook/procfs_example.c +++ b/Documentation/DocBook/procfs_example.c @@ -117,9 +117,6 @@ static int __init init_procfs_example(void) rv = -ENOMEM; goto out; } - - example_dir->owner = THIS_MODULE; - /* create jiffies using convenience function */ jiffies_file = create_proc_read_entry("jiffies", 0444, example_dir, @@ -130,8 +127,6 @@ static int __init init_procfs_example(void) goto no_jiffies; } - jiffies_file->owner = THIS_MODULE; - /* create foo and bar files using same callback * functions */ @@ -146,7 +141,6 @@ static int __init init_procfs_example(void) foo_file->data = &foo_data; foo_file->read_proc = proc_read_foobar; foo_file->write_proc = proc_write_foobar; - foo_file->owner = THIS_MODULE; bar_file = create_proc_entry("bar", 0644, example_dir); if(bar_file == NULL) { @@ -159,7 +153,6 @@ static int __init init_procfs_example(void) bar_file->data = &bar_data; bar_file->read_proc = proc_read_foobar; bar_file->write_proc = proc_write_foobar; - bar_file->owner = THIS_MODULE; /* create symlink */ symlink = proc_symlink("jiffies_too", example_dir, @@ -169,8 +162,6 @@ static int __init init_procfs_example(void) goto no_symlink; } - symlink->owner = THIS_MODULE; - /* everything OK */ printk(KERN_INFO "%s %s initialised\n", MODULE_NAME, MODULE_VERS); diff --git a/Documentation/PCI/MSI-HOWTO.txt b/Documentation/PCI/MSI-HOWTO.txt index 256defd7e17..dcf7acc720e 100644 --- a/Documentation/PCI/MSI-HOWTO.txt +++ b/Documentation/PCI/MSI-HOWTO.txt @@ -4,506 +4,356 @@ Revised Feb 12, 2004 by Martine Silbermann email: Martine.Silbermann@hp.com Revised Jun 25, 2004 by Tom L Nguyen + Revised Jul 9, 2008 by Matthew Wilcox <willy@linux.intel.com> + Copyright 2003, 2008 Intel Corporation 1. About this guide -This guide describes the basics of Message Signaled Interrupts (MSI), -the advantages of using MSI over traditional interrupt mechanisms, -and how to enable your driver to use MSI or MSI-X. Also included is -a Frequently Asked Questions (FAQ) section. - -1.1 Terminology - -PCI devices can be single-function or multi-function. In either case, -when this text talks about enabling or disabling MSI on a "device -function," it is referring to one specific PCI device and function and -not to all functions on a PCI device (unless the PCI device has only -one function). - -2. Copyright 2003 Intel Corporation - -3. What is MSI/MSI-X? - -Message Signaled Interrupt (MSI), as described in the PCI Local Bus -Specification Revision 2.3 or later, is an optional feature, and a -required feature for PCI Express devices. MSI enables a device function -to request service by sending an Inbound Memory Write on its PCI bus to -the FSB as a Message Signal Interrupt transaction. Because MSI is -generated in the form of a Memory Write, all transaction conditions, -such as a Retry, Master-Abort, Target-Abort or normal completion, are -supported. - -A PCI device that supports MSI must also support pin IRQ assertion -interrupt mechanism to provide backward compatibility for systems that -do not support MSI. In systems which support MSI, the bus driver is -responsible for initializing the message address and message data of -the device function's MSI/MSI-X capability structure during device -initial configuration. - -An MSI capable device function indicates MSI support by implementing -the MSI/MSI-X capability structure in its PCI capability list. The -device function may implement both the MSI capability structure and -the MSI-X capability structure; however, the bus driver should not -enable both. - -The MSI capability structure contains Message Control register, -Message Address register and Message Data register. These registers -provide the bus driver control over MSI. The Message Control register -indicates the MSI capability supported by the device. The Message -Address register specifies the target address and the Message Data -register specifies the characteristics of the message. To request -service, the device function writes the content of the Message Data -register to the target address. The device and its software driver -are prohibited from writing to these registers. - -The MSI-X capability structure is an optional extension to MSI. It -uses an independent and separate capability structure. There are -some key advantages to implementing the MSI-X capability structure -over the MSI capability structure as described below. - - - Support a larger maximum number of vectors per function. - - - Provide the ability for system software to configure - each vector with an independent message address and message - data, specified by a table that resides in Memory Space. - - - MSI and MSI-X both support per-vector masking. Per-vector - masking is an optional extension of MSI but a required - feature for MSI-X. Per-vector masking provides the kernel the - ability to mask/unmask a single MSI while running its - interrupt service routine. If per-vector masking is - not supported, then the device driver should provide the - hardware/software synchronization to ensure that the device - generates MSI when the driver wants it to do so. - -4. Why use MSI? - -As a benefit to the simplification of board design, MSI allows board -designers to remove out-of-band interrupt routing. MSI is another -step towards a legacy-free environment. - -Due to increasing pressure on chipset and processor packages to -reduce pin count, the need for interrupt pins is expected to -diminish over time. Devices, due to pin constraints, may implement -messages to increase performance. - -PCI Express endpoints uses INTx emulation (in-band messages) instead -of IRQ pin assertion. Using INTx emulation requires interrupt -sharing among devices connected to the same node (PCI bridge) while -MSI is unique (non-shared) and does not require BIOS configuration -support. As a result, the PCI Express technology requires MSI -support for better interrupt performance. - -Using MSI enables the device functions to support two or more -vectors, which can be configured to target different CPUs to -increase scalability. - -5. Configuring a driver to use MSI/MSI-X - -By default, the kernel will not enable MSI/MSI-X on all devices that -support this capability. The CONFIG_PCI_MSI kernel option -must be selected to enable MSI/MSI-X support. - -5.1 Including MSI/MSI-X support into the kernel - -To allow MSI/MSI-X capable device drivers to selectively enable -MSI/MSI-X (using pci_enable_msi()/pci_enable_msix() as described -below), the VECTOR based scheme needs to be enabled by setting -CONFIG_PCI_MSI during kernel config. - -Since the target of the inbound message is the local APIC, providing -CONFIG_X86_LOCAL_APIC must be enabled as well as CONFIG_PCI_MSI. - -5.2 Configuring for MSI support - -Due to the non-contiguous fashion in vector assignment of the -existing Linux kernel, this version does not support multiple -messages regardless of a device function is capable of supporting -more than one vector. To enable MSI on a device function's MSI -capability structure requires a device driver to call the function -pci_enable_msi() explicitly. - -5.2.1 API pci_enable_msi +This guide describes the basics of Message Signaled Interrupts (MSIs), +the advantages of using MSI over traditional interrupt mechanisms, how +to change your driver to use MSI or MSI-X and some basic diagnostics to +try if a device doesn't support MSIs. -int pci_enable_msi(struct pci_dev *dev) -With this new API, a device driver that wants to have MSI -enabled on its device function must call this API to enable MSI. -A successful call will initialize the MSI capability structure -with ONE vector, regardless of whether a device function is -capable of supporting multiple messages. This vector replaces the -pre-assigned dev->irq with a new MSI vector. To avoid a conflict -of the new assigned vector with existing pre-assigned vector requires -a device driver to call this API before calling request_irq(). +2. What are MSIs? -5.2.2 API pci_disable_msi +A Message Signaled Interrupt is a write from the device to a special +address which causes an interrupt to be received by the CPU. -void pci_disable_msi(struct pci_dev *dev) +The MSI capability was first specified in PCI 2.2 and was later enhanced +in PCI 3.0 to allow each interrupt to be masked individually. The MSI-X +capability was also introduced with PCI 3.0. It supports more interrupts +per device than MSI and allows interrupts to be independently configured. -This API should always be used to undo the effect of pci_enable_msi() -when a device driver is unloading. This API restores dev->irq with -the pre-assigned IOAPIC vector and switches a device's interrupt -mode to PCI pin-irq assertion/INTx emulation mode. - -Note that a device driver should always call free_irq() on the MSI vector -that it has done request_irq() on before calling this API. Failure to do -so results in a BUG_ON() and a device will be left with MSI enabled and -leaks its vector. - -5.2.3 MSI mode vs. legacy mode diagram - -The below diagram shows the events which switch the interrupt -mode on the MSI-capable device function between MSI mode and -PIN-IRQ assertion mode. - - ------------ pci_enable_msi ------------------------ - | | <=============== | | - | MSI MODE | | PIN-IRQ ASSERTION MODE | - | | ===============> | | - ------------ pci_disable_msi ------------------------ - - -Figure 1. MSI Mode vs. Legacy Mode - -In Figure 1, a device operates by default in legacy mode. Legacy -in this context means PCI pin-irq assertion or PCI-Express INTx -emulation. A successful MSI request (using pci_enable_msi()) switches -a device's interrupt mode to MSI mode. A pre-assigned IOAPIC vector -stored in dev->irq will be saved by the PCI subsystem and a new -assigned MSI vector will replace dev->irq. - -To return back to its default mode, a device driver should always call -pci_disable_msi() to undo the effect of pci_enable_msi(). Note that a -device driver should always call free_irq() on the MSI vector it has -done request_irq() on before calling pci_disable_msi(). Failure to do -so results in a BUG_ON() and a device will be left with MSI enabled and -leaks its vector. Otherwise, the PCI subsystem restores a device's -dev->irq with a pre-assigned IOAPIC vector and marks the released -MSI vector as unused. - -Once being marked as unused, there is no guarantee that the PCI -subsystem will reserve this MSI vector for a device. Depending on -the availability of current PCI vector resources and the number of -MSI/MSI-X requests from other drivers, this MSI may be re-assigned. - -For the case where the PCI subsystem re-assigns this MSI vector to -another driver, a request to switch back to MSI mode may result -in being assigned a different MSI vector or a failure if no more -vectors are available. - -5.3 Configuring for MSI-X support - -Due to the ability of the system software to configure each vector of -the MSI-X capability structure with an independent message address -and message data, the non-contiguous fashion in vector assignment of -the existing Linux kernel has no impact on supporting multiple -messages on an MSI-X capable device functions. To enable MSI-X on -a device function's MSI-X capability structure requires its device -driver to call the function pci_enable_msix() explicitly. - -The function pci_enable_msix(), once invoked, enables either -all or nothing, depending on the current availability of PCI vector -resources. If the PCI vector resources are available for the number -of vectors requested by a device driver, this function will configure -the MSI-X table of the MSI-X capability structure of a device with -requested messages. To emphasize this reason, for example, a device -may be capable for supporting the maximum of 32 vectors while its -software driver usually may request 4 vectors. It is recommended -that the device driver should call this function once during the -initialization phase of the device driver. - -Unlike the function pci_enable_msi(), the function pci_enable_msix() -does not replace the pre-assigned IOAPIC dev->irq with a new MSI -vector because the PCI subsystem writes the 1:1 vector-to-entry mapping -into the field vector of each element contained in a second argument. -Note that the pre-assigned IOAPIC dev->irq is valid only if the device -operates in PIN-IRQ assertion mode. In MSI-X mode, any attempt at -using dev->irq by the device driver to request for interrupt service -may result in unpredictable behavior. - -For each MSI-X vector granted, a device driver is responsible for calling -other functions like request_irq(), enable_irq(), etc. to enable -this vector with its corresponding interrupt service handler. It is -a device driver's choice to assign all vectors with the same -interrupt service handler or each vector with a unique interrupt -service handler. - -5.3.1 Handling MMIO address space of MSI-X Table - -The PCI 3.0 specification has implementation notes that MMIO address -space for a device's MSI-X structure should be isolated so that the -software system can set different pages for controlling accesses to the -MSI-X structure. The implementation of MSI support requires the PCI -subsystem, not a device driver, to maintain full control of the MSI-X -table/MSI-X PBA (Pending Bit Array) and MMIO address space of the MSI-X -table/MSI-X PBA. A device driver should not access the MMIO address -space of the MSI-X table/MSI-X PBA. - -5.3.2 API pci_enable_msix +Devices may support both MSI and MSI-X, but only one can be enabled at +a time. -int pci_enable_msix(struct pci_dev *dev, struct msix_entry *entries, int nvec) -This API enables a device driver to request the PCI subsystem -to enable MSI-X messages on its hardware device. Depending on -the availability of PCI vectors resources, the PCI subsystem enables -either all or none of the requested vectors. +3. Why use MSIs? + +There are three reasons why using MSIs can give an advantage over +traditional pin-based interrupts. + +Pin-based PCI interrupts are often shared amongst several devices. +To support this, the kernel must call each interrupt handler associated +with an interrupt, which leads to reduced performance for the system as +a whole. MSIs are never shared, so this problem cannot arise. + +When a device writes data to memory, then raises a pin-based interrupt, +it is possible that the interrupt may arrive before all the data has +arrived in memory (this becomes more likely with devices behind PCI-PCI +bridges). In order to ensure that all the data has arrived in memory, +the interrupt handler must read a register on the device which raised +the interrupt. PCI transaction ordering rules require that all the data +arrives in memory before the value can be returned from the register. +Using MSIs avoids this problem as the interrupt-generating write cannot +pass the data writes, so by the time the interrupt is raised, the driver +knows that all the data has arrived in memory. + +PCI devices can only support a single pin-based interrupt per function. +Often drivers have to query the device to find out what event has +occurred, slowing down interrupt handling for the common case. With +MSIs, a device can support more interrupts, allowing each interrupt +to be specialised to a different purpose. One possible design gives +infrequent conditions (such as errors) their own interrupt which allows +the driver to handle the normal interrupt handling path more efficiently. +Other possible designs include giving one interrupt to each packet queue +in a network card or each port in a storage controller. + + +4. How to use MSIs + +PCI devices are initialised to use pin-based interrupts. The device +driver has to set up the device to use MSI or MSI-X. Not all machines +support MSIs correctly, and for those machines, the APIs described below +will simply fail and the device will continue to use pin-based interrupts. + +4.1 Include kernel support for MSIs + +To support MSI or MSI-X, the kernel must be built with the CONFIG_PCI_MSI +option enabled. This option is only available on some architectures, +and it may depend on some other options also being set. For example, +on x86, you must also enable X86_UP_APIC or SMP in order to see the +CONFIG_PCI_MSI option. + +4.2 Using MSI + +Most of the hard work is done for the driver in the PCI layer. It simply +has to request that the PCI layer set up the MSI capability for this +device. + +4.2.1 pci_enable_msi + +int pci_enable_msi(struct pci_dev *dev) + +A successful call will allocate ONE interrupt to the device, regardless +of how many MSIs the device supports. The device will be switched from +pin-based interrupt mode to MSI mode. The dev->irq number is changed +to a new number which represents the message signaled interrupt. +This function should be called before the driver calls request_irq() +since enabling MSIs disables the pin-based IRQ and the driver will not +receive interrupts on the old interrupt. + +4.2.2 pci_enable_msi_block + +int pci_enable_msi_block(struct pci_dev *dev, int count) + +This variation on the above call allows a device driver to request multiple +MSIs. The MSI specification only allows interrupts to be allocated in +powers of two, up to a maximum of 2^5 (32). + +If this function returns 0, it has succeeded in allocating at least as many +interrupts as the driver requested (it may have allocated more in order +to satisfy the power-of-two requirement). In this case, the function +enables MSI on this device and updates dev->irq to be the lowest of +the new interrupts assigned to it. The other interrupts assigned to +the device are in the range dev->irq to dev->irq + count - 1. + +If this function returns a negative number, it indicates an error and +the driver should not attempt to request any more MSI interrupts for +this device. If this function returns a positive number, it will be +less than 'count' and indicate the number of interrupts that could have +been allocated. In neither case will the irq value have been +updated, nor will the device have been switched into MSI mode. + +The device driver must decide what action to take if +pci_enable_msi_block() returns a value less than the number asked for. +Some devices can make use of fewer interrupts than the maximum they +request; in this case the driver should call pci_enable_msi_block() +again. Note that it is not guaranteed to succeed, even when the +'count' has been reduced to the value returned from a previous call to +pci_enable_msi_block(). This is because there are multiple constraints +on the number of vectors that can be allocated; pci_enable_msi_block() +will return as soon as it finds any constraint that doesn't allow the +call to succeed. + +4.2.3 pci_disable_msi + +void pci_disable_msi(struct pci_dev *dev) -Argument 'dev' points to the device (pci_dev) structure. +This function should be used to undo the effect of pci_enable_msi() or +pci_enable_msi_block(). Calling it restores dev->irq to the pin-based +interrupt number and frees the previously allocated message signaled +interrupt(s). The interrupt may subsequently be assigned to another +device, so drivers should not cache the value of dev->irq. -Argument 'entries' is a pointer to an array of msix_entry structs. -The number of entries is indicated in argument 'nvec'. -struct msix_entry is defined in /driver/pci/msi.h: +A device driver must always call free_irq() on the interrupt(s) +for which it has called request_irq() before calling this function. +Failure to do so will result in a BUG_ON(), the device will be left with +MSI enabled and will leak its vector. + +4.3 Using MSI-X + +The MSI-X capability is much more flexible than the MSI capability. +It supports up to 2048 interrupts, each of which can be controlled +independently. To support this flexibility, drivers must use an array of +`struct msix_entry': struct msix_entry { u16 vector; /* kernel uses to write alloc vector */ u16 entry; /* driver uses to specify entry */ }; -A device driver is responsible for initializing the field 'entry' of -each element with a unique entry supported by MSI-X table. Otherwise, --EINVAL will be returned as a result. A successful return of zero -indicates the PCI subsystem completed initializing each of the requested -entries of the MSI-X table with message address and message data. -Last but not least, the PCI subsystem will write the 1:1 -vector-to-entry mapping into the field 'vector' of each element. A -device driver is responsible for keeping track of allocated MSI-X -vectors in its internal data structure. - -A return of zero indicates that the number of MSI-X vectors was -successfully allocated. A return of greater than zero indicates -MSI-X vector shortage. Or a return of less than zero indicates -a failure. This failure may be a result of duplicate entries -specified in second argument, or a result of no available vector, -or a result of failing to initialize MSI-X table entries. - -5.3.3 API pci_disable_msix +This allows for the device to use these interrupts in a sparse fashion; +for example it could use interrupts 3 and 1027 and allocate only a +two-element array. The driver is expected to fill in the 'entry' value +in each element of the array to indicate which entries it wants the kernel +to assign interrupts for. It is invalid to fill in two entries with the +same number. + +4.3.1 pci_enable_msix + +int pci_enable_msix(struct pci_dev *dev, struct msix_entry *entries, int nvec) + +Calling this function asks the PCI subsystem to allocate 'nvec' MSIs. +The 'entries' argument is a pointer to an array of msix_entry structs +which should be at least 'nvec' entries in size. On success, the +function will return 0 and the device will have been switched into +MSI-X interrupt mode. The 'vector' elements in each entry will have +been filled in with the interrupt number. The driver should then call +request_irq() for each 'vector' that it decides to use. + +If this function returns a negative number, it indicates an error and +the driver should not attempt to allocate any more MSI-X interrupts for +this device. If it returns a positive number, it indicates the maximum +number of interrupt vectors that could have been allocated. See example +below. + +This function, in contrast with pci_enable_msi(), does not adjust +dev->irq. The device will not generate interrupts for this interrupt +number once MSI-X is enabled. The device driver is responsible for +keeping track of the interrupts assigned to the MSI-X vectors so it can +free them again later. + +Device drivers should normally call this function once per device +during the initialization phase. + +It is ideal if drivers can cope with a variable number of MSI-X interrupts, +there are many reasons why the platform may not be able to provide the +exact number a driver asks for. + +A request loop to achieve that might look like: + +static int foo_driver_enable_msix(struct foo_adapter *adapter, int nvec) +{ + while (nvec >= FOO_DRIVER_MINIMUM_NVEC) { + rc = pci_enable_msix(adapter->pdev, + adapter->msix_entries, nvec); + if (rc > 0) + nvec = rc; + else + return rc; + } + + return -ENOSPC; +} + +4.3.2 pci_disable_msix void pci_disable_msix(struct pci_dev *dev) -This API should always be used to undo the effect of pci_enable_msix() -when a device driver is unloading. Note that a device driver should -always call free_irq() on all MSI-X vectors it has done request_irq() -on before calling this API. Failure to do so results in a BUG_ON() and -a device will be left with MSI-X enabled and leaks its vectors. - -5.3.4 MSI-X mode vs. legacy mode diagram - -The below diagram shows the events which switch the interrupt -mode on the MSI-X capable device function between MSI-X mode and -PIN-IRQ assertion mode (legacy). - - ------------ pci_enable_msix(,,n) ------------------------ - | | <=============== | | - | MSI-X MODE | | PIN-IRQ ASSERTION MODE | - | | ===============> | | - ------------ pci_disable_msix ------------------------ - -Figure 2. MSI-X Mode vs. Legacy Mode - -In Figure 2, a device operates by default in legacy mode. A -successful MSI-X request (using pci_enable_msix()) switches a -device's interrupt mode to MSI-X mode. A pre-assigned IOAPIC vector -stored in dev->irq will be saved by the PCI subsystem; however, -unlike MSI mode, the PCI subsystem will not replace dev->irq with -assigned MSI-X vector because the PCI subsystem already writes the 1:1 -vector-to-entry mapping into the field 'vector' of each element -specified in second argument. - -To return back to its default mode, a device driver should always call -pci_disable_msix() to undo the effect of pci_enable_msix(). Note that -a device driver should always call free_irq() on all MSI-X vectors it -has done request_irq() on before calling pci_disable_msix(). Failure -to do so results in a BUG_ON() and a device will be left with MSI-X -enabled and leaks its vectors. Otherwise, the PCI subsystem switches a -device function's interrupt mode from MSI-X mode to legacy mode and -marks all allocated MSI-X vectors as unused. - -Once being marked as unused, there is no guarantee that the PCI -subsystem will reserve these MSI-X vectors for a device. Depending on -the availability of current PCI vector resources and the number of -MSI/MSI-X requests from other drivers, these MSI-X vectors may be -re-assigned. - -For the case where the PCI subsystem re-assigned these MSI-X vectors -to other drivers, a request to switch back to MSI-X mode may result -being assigned with another set of MSI-X vectors or a failure if no -more vectors are available. - -5.4 Handling function implementing both MSI and MSI-X capabilities - -For the case where a function implements both MSI and MSI-X -capabilities, the PCI subsystem enables a device to run either in MSI -mode or MSI-X mode but not both. A device driver determines whether it -wants MSI or MSI-X enabled on its hardware device. Once a device -driver requests for MSI, for example, it is prohibited from requesting -MSI-X; in other words, a device driver is not permitted to ping-pong -between MSI mod MSI-X mode during a run-time. - -5.5 Hardware requirements for MSI/MSI-X support - -MSI/MSI-X support requires support from both system hardware and -individual hardware device functions. - -5.5.1 Required x86 hardware support - -Since the target of MSI address is the local APIC CPU, enabling -MSI/MSI-X support in the Linux kernel is dependent on whether existing -system hardware supports local APIC. Users should verify that their -system supports local APIC operation by testing that it runs when -CONFIG_X86_LOCAL_APIC=y. - -In SMP environment, CONFIG_X86_LOCAL_APIC is automatically set; -however, in UP environment, users must manually set -CONFIG_X86_LOCAL_APIC. Once CONFIG_X86_LOCAL_APIC=y, setting -CONFIG_PCI_MSI enables the VECTOR based scheme and the option for -MSI-capable device drivers to selectively enable MSI/MSI-X. - -Note that CONFIG_X86_IO_APIC setting is irrelevant because MSI/MSI-X -vector is allocated new during runtime and MSI/MSI-X support does not -depend on BIOS support. This key independency enables MSI/MSI-X -support on future IOxAPIC free platforms. - -5.5.2 Device hardware support - -The hardware device function supports MSI by indicating the -MSI/MSI-X capability structure on its PCI capability list. By -default, this capability structure will not be initialized by -the kernel to enable MSI during the system boot. In other words, -the device function is running on its default pin assertion mode. -Note that in many cases the hardware supporting MSI have bugs, -which may result in system hangs. The software driver of specific -MSI-capable hardware is responsible for deciding whether to call -pci_enable_msi or not. A return of zero indicates the kernel -successfully initialized the MSI/MSI-X capability structure of the -device function. The device function is now running on MSI/MSI-X mode. - -5.6 How to tell whether MSI/MSI-X is enabled on device function - -At the driver level, a return of zero from the function call of -pci_enable_msi()/pci_enable_msix() indicates to a device driver that -its device function is initialized successfully and ready to run in -MSI/MSI-X mode. - -At the user level, users can use the command 'cat /proc/interrupts' -to display the vectors allocated for devices and their interrupt -MSI/MSI-X modes ("PCI-MSI"/"PCI-MSI-X"). Below shows MSI mode is -enabled on a SCSI Adaptec 39320D Ultra320 controller. - - CPU0 CPU1 - 0: 324639 0 IO-APIC-edge timer - 1: 1186 0 IO-APIC-edge i8042 - 2: 0 0 XT-PIC cascade - 12: 2797 0 IO-APIC-edge i8042 - 14: 6543 0 IO-APIC-edge ide0 - 15: 1 0 IO-APIC-edge ide1 -169: 0 0 IO-APIC-level uhci-hcd -185: 0 0 IO-APIC-level uhci-hcd -193: 138 10 PCI-MSI aic79xx -201: 30 0 PCI-MSI aic79xx -225: 30 0 IO-APIC-level aic7xxx -233: 30 0 IO-APIC-level aic7xxx -NMI: 0 0 -LOC: 324553 325068 -ERR: 0 -MIS: 0 - -6. MSI quirks - -Several PCI chipsets or devices are known to not support MSI. -The PCI stack provides 3 possible levels of MSI disabling: -* on a single device -* on all devices behind a specific bridge -* globally - -6.1. Disabling MSI on a single device - -Under some circumstances it might be required to disable MSI on a -single device. This may be achieved by either not calling pci_enable_msi() -or all, or setting the pci_dev->no_msi flag before (most of the time -in a quirk). - -6.2. Disabling MSI below a bridge - -The vast majority of MSI quirks are required by PCI bridges not -being able to route MSI between busses. In this case, MSI have to be -disabled on all devices behind this bridge. It is achieves by setting -the PCI_BUS_FLAGS_NO_MSI flag in the pci_bus->bus_flags of the bridge -subordinate bus. There is no need to set the same flag on bridges that -are below the broken bridge. When pci_enable_msi() is called to enable -MSI on a device, pci_msi_supported() takes care of checking the NO_MSI -flag in all parent busses of the device. - -Some bridges actually support dynamic MSI support enabling/disabling -by changing some bits in their PCI configuration space (especially -the Hypertransport chipsets such as the nVidia nForce and Serverworks -HT2000). It may then be required to update the NO_MSI flag on the -corresponding devices in the sysfs hierarchy. To enable MSI support -on device "0000:00:0e", do: - - echo 1 > /sys/bus/pci/devices/0000:00:0e/msi_bus - -To disable MSI support, echo 0 instead of 1. Note that it should be -used with caution since changing this value might break interrupts. - -6.3. Disabling MSI globally - -Some extreme cases may require to disable MSI globally on the system. -For now, the only known case is a Serverworks PCI-X chipsets (MSI are -not supported on several busses that are not all connected to the -chipset in the Linux PCI hierarchy). In the vast majority of other -cases, disabling only behind a specific bridge is enough. - -For debugging purpose, the user may also pass pci=nomsi on the kernel -command-line to explicitly disable MSI globally. But, once the appro- -priate quirks are added to the kernel, this option should not be -required anymore. - -6.4. Finding why MSI cannot be enabled on a device - -Assuming that MSI are not enabled on a device, you should look at -dmesg to find messages that quirks may output when disabling MSI -on some devices, some bridges or even globally. -Then, lspci -t gives the list of bridges above a device. Reading -/sys/bus/pci/devices/0000:00:0e/msi_bus will tell you whether MSI -are enabled (1) or disabled (0). In 0 is found in a single bridge -msi_bus file above the device, MSI cannot be enabled. - -7. FAQ - -Q1. Are there any limitations on using the MSI? - -A1. If the PCI device supports MSI and conforms to the -specification and the platform supports the APIC local bus, -then using MSI should work. - -Q2. Will it work on all the Pentium processors (P3, P4, Xeon, -AMD processors)? In P3 IPI's are transmitted on the APIC local -bus and in P4 and Xeon they are transmitted on the system -bus. Are there any implications with this? - -A2. MSI support enables a PCI device sending an inbound -memory write (0xfeexxxxx as target address) on its PCI bus -directly to the FSB. Since the message address has a -redirection hint bit cleared, it should work. - -Q3. The target address 0xfeexxxxx will be translated by the -Host Bridge into an interrupt message. Are there any -limitations on the chipsets such as Intel 8xx, Intel e7xxx, -or VIA? - -A3. If these chipsets support an inbound memory write with -target address set as 0xfeexxxxx, as conformed to PCI -specification 2.3 or latest, then it should work. - -Q4. From the driver point of view, if the MSI is lost because -of errors occurring during inbound memory write, then it may -wait forever. Is there a mechanism for it to recover? - -A4. Since the target of the transaction is an inbound memory -write, all transaction termination conditions (Retry, -Master-Abort, Target-Abort, or normal completion) are -supported. A device sending an MSI must abide by all the PCI -rules and conditions regarding that inbound memory write. So, -if a retry is signaled it must retry, etc... We believe that -the recommendation for Abort is also a retry (refer to PCI -specification 2.3 or latest). +This API should be used to undo the effect of pci_enable_msix(). It frees +the previously allocated message signaled interrupts. The interrupts may +subsequently be assigned to another device, so drivers should not cache +the value of the 'vector' elements over a call to pci_disable_msix(). + +A device driver must always call free_irq() on the interrupt(s) +for which it has called request_irq() before calling this function. +Failure to do so will result in a BUG_ON(), the device will be left with +MSI enabled and will leak its vector. + +4.3.3 The MSI-X Table + +The MSI-X capability specifies a BAR and offset within that BAR for the +MSI-X Table. This address is mapped by the PCI subsystem, and should not +be accessed directly by the device driver. If the driver wishes to +mask or unmask an interrupt, it should call disable_irq() / enable_irq(). + +4.4 Handling devices implementing both MSI and MSI-X capabilities + +If a device implements both MSI and MSI-X capabilities, it can +run in either MSI mode or MSI-X mode but not both simultaneously. +This is a requirement of the PCI spec, and it is enforced by the +PCI layer. Calling pci_enable_msi() when MSI-X is already enabled or +pci_enable_msix() when MSI is already enabled will result in an error. +If a device driver wishes to switch between MSI and MSI-X at runtime, +it must first quiesce the device, then switch it back to pin-interrupt +mode, before calling pci_enable_msi() or pci_enable_msix() and resuming +operation. This is not expected to be a common operation but may be +useful for debugging or testing during development. + +4.5 Considerations when using MSIs + +4.5.1 Choosing between MSI-X and MSI + +If your device supports both MSI-X and MSI capabilities, you should use +the MSI-X facilities in preference to the MSI facilities. As mentioned +above, MSI-X supports any number of interrupts between 1 and 2048. +In constrast, MSI is restricted to a maximum of 32 interrupts (and +must be a power of two). In addition, the MSI interrupt vectors must +be allocated consecutively, so the system may not be able to allocate +as many vectors for MSI as it could for MSI-X. On some platforms, MSI +interrupts must all be targetted at the same set of CPUs whereas MSI-X +interrupts can all be targetted at different CPUs. + +4.5.2 Spinlocks + +Most device drivers have a per-device spinlock which is taken in the +interrupt handler. With pin-based interrupts or a single MSI, it is not +necessary to disable interrupts (Linux guarantees the same interrupt will +not be re-entered). If a device uses multiple interrupts, the driver +must disable interrupts while the lock is held. If the device sends +a different interrupt, the driver will deadlock trying to recursively +acquire the spinlock. + +There are two solutions. The first is to take the lock with +spin_lock_irqsave() or spin_lock_irq() (see +Documentation/DocBook/kernel-locking). The second is to specify +IRQF_DISABLED to request_irq() so that the kernel runs the entire +interrupt routine with interrupts disabled. + +If your MSI interrupt routine does not hold the lock for the whole time +it is running, the first solution may be best. The second solution is +normally preferred as it avoids making two transitions from interrupt +disabled to enabled and back again. + +4.6 How to tell whether MSI/MSI-X is enabled on a device + +Using 'lspci -v' (as root) may show some devices with "MSI", "Message +Signalled Interrupts" or "MSI-X" capabilities. Each of these capabilities +has an 'Enable' flag which will be followed with either "+" (enabled) +or "-" (disabled). + + +5. MSI quirks + +Several PCI chipsets or devices are known not to support MSIs. +The PCI stack provides three ways to disable MSIs: + +1. globally +2. on all devices behind a specific bridge +3. on a single device + +5.1. Disabling MSIs globally + +Some host chipsets simply don't support MSIs properly. If we're +lucky, the manufacturer knows this and has indicated it in the ACPI +FADT table. In this case, Linux will automatically disable MSIs. +Some boards don't include this information in the table and so we have +to detect them ourselves. The complete list of these is found near the +quirk_disable_all_msi() function in drivers/pci/quirks.c. + +If you have a board which has problems with MSIs, you can pass pci=nomsi +on the kernel command line to disable MSIs on all devices. It would be +in your best interests to report the problem to linux-pci@vger.kernel.org +including a full 'lspci -v' so we can add the quirks to the kernel. + +5.2. Disabling MSIs below a bridge + +Some PCI bridges are not able to route MSIs between busses properly. +In this case, MSIs must be disabled on all devices behind the bridge. + +Some bridges allow you to enable MSIs by changing some bits in their +PCI configuration space (especially the Hypertransport chipsets such +as the nVidia nForce and Serverworks HT2000). As with host chipsets, +Linux mostly knows about them and automatically enables MSIs if it can. +If you have a bridge which Linux doesn't yet know about, you can enable +MSIs in configuration space using whatever method you know works, then +enable MSIs on that bridge by doing: + + echo 1 > /sys/bus/pci/devices/$bridge/msi_bus + +where $bridge is the PCI address of the bridge you've enabled (eg +0000:00:0e.0). + +To disable MSIs, echo 0 instead of 1. Changing this value should be +done with caution as it can break interrupt handling for all devices +below this bridge. + +Again, please notify linux-pci@vger.kernel.org of any bridges that need +special handling. + +5.3. Disabling MSIs on a single device + +Some devices are known to have faulty MSI implementations. Usually this +is handled in the individual device driver but occasionally it's necessary +to handle this with a quirk. Some drivers have an option to disable use +of MSI. While this is a convenient workaround for the driver author, +it is not good practise, and should not be emulated. + +5.4. Finding why MSIs are disabled on a device + +From the above three sections, you can see that there are many reasons +why MSIs may not be enabled for a given device. Your first step should +be to examine your dmesg carefully to determine whether MSIs are enabled +for your machine. You should also check your .config to be sure you +have enabled CONFIG_PCI_MSI. + +Then, 'lspci -t' gives the list of bridges above a device. Reading +/sys/bus/pci/devices/*/msi_bus will tell you whether MSI are enabled (1) +or disabled (0). If 0 is found in any of the msi_bus files belonging +to bridges between the PCI root and the device, MSIs are disabled. + +It is also worth checking the device driver to see whether it supports MSIs. +For example, it may contain calls to pci_enable_msi(), pci_enable_msix() or +pci_enable_msi_block(). diff --git a/Documentation/PCI/pci-iov-howto.txt b/Documentation/PCI/pci-iov-howto.txt new file mode 100644 index 00000000000..fc73ef5d65b --- /dev/null +++ b/Documentation/PCI/pci-iov-howto.txt @@ -0,0 +1,99 @@ + PCI Express I/O Virtualization Howto + Copyright (C) 2009 Intel Corporation + Yu Zhao <yu.zhao@intel.com> + + +1. Overview + +1.1 What is SR-IOV + +Single Root I/O Virtualization (SR-IOV) is a PCI Express Extended +capability which makes one physical device appear as multiple virtual +devices. The physical device is referred to as Physical Function (PF) +while the virtual devices are referred to as Virtual Functions (VF). +Allocation of the VF can be dynamically controlled by the PF via +registers encapsulated in the capability. By default, this feature is +not enabled and the PF behaves as traditional PCIe device. Once it's +turned on, each VF's PCI configuration space can be accessed by its own +Bus, Device and Function Number (Routing ID). And each VF also has PCI +Memory Space, which is used to map its register set. VF device driver +operates on the register set so it can be functional and appear as a +real existing PCI device. + +2. User Guide + +2.1 How can I enable SR-IOV capability + +The device driver (PF driver) will control the enabling and disabling +of the capability via API provided by SR-IOV core. If the hardware +has SR-IOV capability, loading its PF driver would enable it and all +VFs associated with the PF. + +2.2 How can I use the Virtual Functions + +The VF is treated as hot-plugged PCI devices in the kernel, so they +should be able to work in the same way as real PCI devices. The VF +requires device driver that is same as a normal PCI device's. + +3. Developer Guide + +3.1 SR-IOV API + +To enable SR-IOV capability: + int pci_enable_sriov(struct pci_dev *dev, int nr_virtfn); + 'nr_virtfn' is number of VFs to be enabled. + +To disable SR-IOV capability: + void pci_disable_sriov(struct pci_dev *dev); + +To notify SR-IOV core of Virtual Function Migration: + irqreturn_t pci_sriov_migration(struct pci_dev *dev); + +3.2 Usage example + +Following piece of code illustrates the usage of the SR-IOV API. + +static int __devinit dev_probe(struct pci_dev *dev, const struct pci_device_id *id) +{ + pci_enable_sriov(dev, NR_VIRTFN); + + ... + + return 0; +} + +static void __devexit dev_remove(struct pci_dev *dev) +{ + pci_disable_sriov(dev); + + ... +} + +static int dev_suspend(struct pci_dev *dev, pm_message_t state) +{ + ... + + return 0; +} + +static int dev_resume(struct pci_dev *dev) +{ + ... + + return 0; +} + +static void dev_shutdown(struct pci_dev *dev) +{ + ... +} + +static struct pci_driver dev_driver = { + .name = "SR-IOV Physical Function driver", + .id_table = dev_id_table, + .probe = dev_probe, + .remove = __devexit_p(dev_remove), + .suspend = dev_suspend, + .resume = dev_resume, + .shutdown = dev_shutdown, +}; diff --git a/Documentation/Smack.txt b/Documentation/Smack.txt index 989c2fcd811..629c92e9978 100644 --- a/Documentation/Smack.txt +++ b/Documentation/Smack.txt @@ -184,14 +184,16 @@ length. Single character labels using special characters, that being anything other than a letter or digit, are reserved for use by the Smack development team. Smack labels are unstructured, case sensitive, and the only operation ever performed on them is comparison for equality. Smack labels cannot -contain unprintable characters or the "/" (slash) character. +contain unprintable characters or the "/" (slash) character. Smack labels +cannot begin with a '-', which is reserved for special options. There are some predefined labels: - _ Pronounced "floor", a single underscore character. - ^ Pronounced "hat", a single circumflex character. - * Pronounced "star", a single asterisk character. - ? Pronounced "huh", a single question mark character. + _ Pronounced "floor", a single underscore character. + ^ Pronounced "hat", a single circumflex character. + * Pronounced "star", a single asterisk character. + ? Pronounced "huh", a single question mark character. + @ Pronounced "Internet", a single at sign character. Every task on a Smack system is assigned a label. System tasks, such as init(8) and systems daemons, are run with the floor ("_") label. User tasks @@ -412,6 +414,36 @@ sockets. A privileged program may set this to match the label of another task with which it hopes to communicate. +Smack Netlabel Exceptions + +You will often find that your labeled application has to talk to the outside, +unlabeled world. To do this there's a special file /smack/netlabel where you can +add some exceptions in the form of : +@IP1 LABEL1 or +@IP2/MASK LABEL2 + +It means that your application will have unlabeled access to @IP1 if it has +write access on LABEL1, and access to the subnet @IP2/MASK if it has write +access on LABEL2. + +Entries in the /smack/netlabel file are matched by longest mask first, like in +classless IPv4 routing. + +A special label '@' and an option '-CIPSO' can be used there : +@ means Internet, any application with any label has access to it +-CIPSO means standard CIPSO networking + +If you don't know what CIPSO is and don't plan to use it, you can just do : +echo 127.0.0.1 -CIPSO > /smack/netlabel +echo 0.0.0.0/0 @ > /smack/netlabel + +If you use CIPSO on your 192.168.0.0/16 local network and need also unlabeled +Internet access, you can have : +echo 127.0.0.1 -CIPSO > /smack/netlabel +echo 192.168.0.0/16 -CIPSO > /smack/netlabel +echo 0.0.0.0/0 @ > /smack/netlabel + + Writing Applications for Smack There are three sorts of applications that will run on a Smack system. How an diff --git a/Documentation/cgroups/cgroups.txt b/Documentation/cgroups/cgroups.txt index 93feb844448..4ea852345a4 100644 --- a/Documentation/cgroups/cgroups.txt +++ b/Documentation/cgroups/cgroups.txt @@ -333,12 +333,23 @@ The "xxx" is not interpreted by the cgroup code, but will appear in To mount a cgroup hierarchy with just the cpuset and numtasks subsystems, type: -# mount -t cgroup -o cpuset,numtasks hier1 /dev/cgroup +# mount -t cgroup -o cpuset,memory hier1 /dev/cgroup To change the set of subsystems bound to a mounted hierarchy, just remount with different options: +# mount -o remount,cpuset,ns hier1 /dev/cgroup -# mount -o remount,cpuset,ns /dev/cgroup +Now memory is removed from the hierarchy and ns is added. + +Note this will add ns to the hierarchy but won't remove memory or +cpuset, because the new options are appended to the old ones: +# mount -o remount,ns /dev/cgroup + +To Specify a hierarchy's release_agent: +# mount -t cgroup -o cpuset,release_agent="/sbin/cpuset_release_agent" \ + xxx /dev/cgroup + +Note that specifying 'release_agent' more than once will return failure. Note that changing the set of subsystems is currently only supported when the hierarchy consists of a single (root) cgroup. Supporting @@ -349,6 +360,11 @@ Then under /dev/cgroup you can find a tree that corresponds to the tree of the cgroups in the system. For instance, /dev/cgroup is the cgroup that holds the whole system. +If you want to change the value of release_agent: +# echo "/sbin/new_release_agent" > /dev/cgroup/release_agent + +It can also be changed via remount. + If you want to create a new cgroup under /dev/cgroup: # cd /dev/cgroup # mkdir my_cgroup @@ -476,11 +492,13 @@ cgroup->parent is still valid. (Note - can also be called for a newly-created cgroup if an error occurs after this subsystem's create() method has been called for the new cgroup). -void pre_destroy(struct cgroup_subsys *ss, struct cgroup *cgrp); +int pre_destroy(struct cgroup_subsys *ss, struct cgroup *cgrp); Called before checking the reference count on each subsystem. This may be useful for subsystems which have some extra references even if -there are not tasks in the cgroup. +there are not tasks in the cgroup. If pre_destroy() returns error code, +rmdir() will fail with it. From this behavior, pre_destroy() can be +called multiple times against a cgroup. int can_attach(struct cgroup_subsys *ss, struct cgroup *cgrp, struct task_struct *task) diff --git a/Documentation/cgroups/memcg_test.txt b/Documentation/cgroups/memcg_test.txt index 523a9c16c40..8a11caf417a 100644 --- a/Documentation/cgroups/memcg_test.txt +++ b/Documentation/cgroups/memcg_test.txt @@ -1,5 +1,5 @@ Memory Resource Controller(Memcg) Implementation Memo. -Last Updated: 2009/1/19 +Last Updated: 2009/1/20 Base Kernel Version: based on 2.6.29-rc2. Because VM is getting complex (one of reasons is memcg...), memcg's behavior @@ -360,3 +360,21 @@ Under below explanation, we assume CONFIG_MEM_RES_CTRL_SWAP=y. # kill malloc task. Of course, tmpfs v.s. swapoff test should be tested, too. + + 9.8 OOM-Killer + Out-of-memory caused by memcg's limit will kill tasks under + the memcg. When hierarchy is used, a task under hierarchy + will be killed by the kernel. + In this case, panic_on_oom shouldn't be invoked and tasks + in other groups shouldn't be killed. + + It's not difficult to cause OOM under memcg as following. + Case A) when you can swapoff + #swapoff -a + #echo 50M > /memory.limit_in_bytes + run 51M of malloc + + Case B) when you use mem+swap limitation. + #echo 50M > memory.limit_in_bytes + #echo 50M > memory.memsw.limit_in_bytes + run 51M of malloc diff --git a/Documentation/dvb/get_dvb_firmware b/Documentation/dvb/get_dvb_firmware index f2e908d7f90..2f21ecd4c20 100644 --- a/Documentation/dvb/get_dvb_firmware +++ b/Documentation/dvb/get_dvb_firmware @@ -25,7 +25,7 @@ use IO::Handle; "tda10046lifeview", "av7110", "dec2000t", "dec2540t", "dec3000s", "vp7041", "dibusb", "nxt2002", "nxt2004", "or51211", "or51132_qam", "or51132_vsb", "bluebird", - "opera1"); + "opera1", "cx231xx", "cx18", "cx23885", "pvrusb2" ); # Check args syntax() if (scalar(@ARGV) != 1); @@ -37,8 +37,8 @@ for ($i=0; $i < scalar(@components); $i++) { $outfile = eval($cid); die $@ if $@; print STDERR <<EOF; -Firmware $outfile extracted successfully. -Now copy it to either /usr/lib/hotplug/firmware or /lib/firmware +Firmware(s) $outfile extracted successfully. +Now copy it(they) to either /usr/lib/hotplug/firmware or /lib/firmware (depending on configuration of firmware hotplug). EOF exit(0); @@ -345,6 +345,85 @@ sub or51211 { $fwfile; } +sub cx231xx { + my $fwfile = "v4l-cx231xx-avcore-01.fw"; + my $url = "http://linuxtv.org/downloads/firmware/$fwfile"; + my $hash = "7d3bb956dc9df0eafded2b56ba57cc42"; + + checkstandard(); + + wgetfile($fwfile, $url); + verify($fwfile, $hash); + + $fwfile; +} + +sub cx18 { + my $url = "http://linuxtv.org/downloads/firmware/"; + + my %files = ( + 'v4l-cx23418-apu.fw' => '588f081b562f5c653a3db1ad8f65939a', + 'v4l-cx23418-cpu.fw' => 'b6c7ed64bc44b1a6e0840adaeac39d79', + 'v4l-cx23418-dig.fw' => '95bc688d3e7599fd5800161e9971cc55', + ); + + checkstandard(); + + my $allfiles; + foreach my $fwfile (keys %files) { + wgetfile($fwfile, "$url/$fwfile"); + verify($fwfile, $files{$fwfile}); + $allfiles .= " $fwfile"; + } + + $allfiles =~ s/^\s//; + + $allfiles; +} + +sub cx23885 { + my $url = "http://linuxtv.org/downloads/firmware/"; + + my %files = ( + 'v4l-cx23885-avcore-01.fw' => 'a9f8f5d901a7fb42f552e1ee6384f3bb', + 'v4l-cx23885-enc.fw' => 'a9f8f5d901a7fb42f552e1ee6384f3bb', + ); + + checkstandard(); + + my $allfiles; + foreach my $fwfile (keys %files) { + wgetfile($fwfile, "$url/$fwfile"); + verify($fwfile, $files{$fwfile}); + $allfiles .= " $fwfile"; + } + + $allfiles =~ s/^\s//; + + $allfiles; +} + +sub pvrusb2 { + my $url = "http://linuxtv.org/downloads/firmware/"; + + my %files = ( + 'v4l-cx25840.fw' => 'dadb79e9904fc8af96e8111d9cb59320', + ); + + checkstandard(); + + my $allfiles; + foreach my $fwfile (keys %files) { + wgetfile($fwfile, "$url/$fwfile"); + verify($fwfile, $files{$fwfile}); + $allfiles .= " $fwfile"; + } + + $allfiles =~ s/^\s//; + + $allfiles; +} + sub or51132_qam { my $fwfile = "dvb-fe-or51132-qam.fw"; my $url = "http://linuxtv.org/downloads/firmware/$fwfile"; diff --git a/Documentation/fb/00-INDEX b/Documentation/fb/00-INDEX index caabbd395e6..a618fd99c9f 100644 --- a/Documentation/fb/00-INDEX +++ b/Documentation/fb/00-INDEX @@ -11,8 +11,6 @@ aty128fb.txt - info on the ATI Rage128 frame buffer driver. cirrusfb.txt - info on the driver for Cirrus Logic chipsets. -cyblafb/ - - directory with documentation files related to the cyblafb driver. deferred_io.txt - an introduction to deferred IO. fbcon.txt diff --git a/Documentation/fb/cyblafb/bugs b/Documentation/fb/cyblafb/bugs deleted file mode 100644 index 9443a6d72cd..00000000000 --- a/Documentation/fb/cyblafb/bugs +++ /dev/null @@ -1,13 +0,0 @@ -Bugs -==== - -I currently don't know of any bug. Please do send reports to: - - linux-fbdev-devel@lists.sourceforge.net - - Knut_Petersen@t-online.de. - - -Untested features -================= - -All LCD stuff is untested. If it worked in tridentfb, it should work in -cyblafb. Please test and report the results to Knut_Petersen@t-online.de. diff --git a/Documentation/fb/cyblafb/credits b/Documentation/fb/cyblafb/credits deleted file mode 100644 index 0eb3b443dc2..00000000000 --- a/Documentation/fb/cyblafb/credits +++ /dev/null @@ -1,7 +0,0 @@ -Thanks to -========= - * Alan Hourihane, for writing the X trident driver - * Jani Monoses, for writing the tridentfb driver - * Antonino A. Daplas, for review of the first published - version of cyblafb and some code - * Jochen Hein, for testing and a helpfull bug report diff --git a/Documentation/fb/cyblafb/documentation b/Documentation/fb/cyblafb/documentation deleted file mode 100644 index bb1aac04842..00000000000 --- a/Documentation/fb/cyblafb/documentation +++ /dev/null @@ -1,17 +0,0 @@ -Available Documentation -======================= - -Apollo PLE 133 Chipset VT8601A North Bridge Datasheet, Rev. 1.82, October 22, -2001, available from VIA: - - http://www.viavpsd.com/product/6/15/DS8601A182.pdf - -The datasheet is incomplete, some registers that need to be programmed are not -explained at all and important bits are listed as "reserved". But you really -need the datasheet to understand the code. "p. xxx" comments refer to page -numbers of this document. - -XFree/XOrg drivers are available and of good quality, looking at the code -there is a good idea if the datasheet does not provide enough information -or if the datasheet seems to be wrong. - diff --git a/Documentation/fb/cyblafb/fb.modes b/Documentation/fb/cyblafb/fb.modes deleted file mode 100644 index fe0e5223ba8..00000000000 --- a/Documentation/fb/cyblafb/fb.modes +++ /dev/null @@ -1,154 +0,0 @@ -# -# Sample fb.modes file -# -# Provides an incomplete list of working modes for -# the cyberblade/i1 graphics core. -# -# The value 4294967256 is used instead of -40. Of course, -40 is not -# a really reasonable value, but chip design does not always follow -# logic. Believe me, it's ok, and it's the way the BIOS does it. -# -# fbset requires 4294967256 in fb.modes and -40 as an argument to -# the -t parameter. That's also not too reasonable, and it might change -# in the future or might even be differt for your current version. -# - -mode "640x480-50" - geometry 640 480 2048 4096 8 - timings 47619 4294967256 24 17 0 216 3 -endmode - -mode "640x480-60" - geometry 640 480 2048 4096 8 - timings 39682 4294967256 24 17 0 216 3 -endmode - -mode "640x480-70" - geometry 640 480 2048 4096 8 - timings 34013 4294967256 24 17 0 216 3 -endmode - -mode "640x480-72" - geometry 640 480 2048 4096 8 - timings 33068 4294967256 24 17 0 216 3 -endmode - -mode "640x480-75" - geometry 640 480 2048 4096 8 - timings 31746 4294967256 24 17 0 216 3 -endmode - -mode "640x480-80" - geometry 640 480 2048 4096 8 - timings 29761 4294967256 24 17 0 216 3 -endmode - -mode "640x480-85" - geometry 640 480 2048 4096 8 - timings 28011 4294967256 24 17 0 216 3 -endmode - -mode "800x600-50" - geometry 800 600 2048 4096 8 - timings 30303 96 24 14 0 136 11 -endmode - -mode "800x600-60" - geometry 800 600 2048 4096 8 - timings 25252 96 24 14 0 136 11 -endmode - -mode "800x600-70" - geometry 800 600 2048 4096 8 - timings 21645 96 24 14 0 136 11 -endmode - -mode "800x600-72" - geometry 800 600 2048 4096 8 - timings 21043 96 24 14 0 136 11 -endmode - -mode "800x600-75" - geometry 800 600 2048 4096 8 - timings 20202 96 24 14 0 136 11 -endmode - -mode "800x600-80" - geometry 800 600 2048 4096 8 - timings 18939 96 24 14 0 136 11 -endmode - -mode "800x600-85" - geometry 800 600 2048 4096 8 - timings 17825 96 24 14 0 136 11 -endmode - -mode "1024x768-50" - geometry 1024 768 2048 4096 8 - timings 19054 144 24 29 0 120 3 -endmode - -mode "1024x768-60" - geometry 1024 768 2048 4096 8 - timings 15880 144 24 29 0 120 3 -endmode - -mode "1024x768-70" - geometry 1024 768 2048 4096 8 - timings 13610 144 24 29 0 120 3 -endmode - -mode "1024x768-72" - geometry 1024 768 2048 4096 8 - timings 13232 144 24 29 0 120 3 -endmode - -mode "1024x768-75" - geometry 1024 768 2048 4096 8 - timings 12703 144 24 29 0 120 3 -endmode - -mode "1024x768-80" - geometry 1024 768 2048 4096 8 - timings 11910 144 24 29 0 120 3 -endmode - -mode "1024x768-85" - geometry 1024 768 2048 4096 8 - timings 11209 144 24 29 0 120 3 -endmode - -mode "1280x1024-50" - geometry 1280 1024 2048 4096 8 - timings 11114 232 16 39 0 160 3 -endmode - -mode "1280x1024-60" - geometry 1280 1024 2048 4096 8 - timings 9262 232 16 39 0 160 3 -endmode - -mode "1280x1024-70" - geometry 1280 1024 2048 4096 8 - timings 7939 232 16 39 0 160 3 -endmode - -mode "1280x1024-72" - geometry 1280 1024 2048 4096 8 - timings 7719 232 16 39 0 160 3 -endmode - -mode "1280x1024-75" - geometry 1280 1024 2048 4096 8 - timings 7410 232 16 39 0 160 3 -endmode - -mode "1280x1024-80" - geometry 1280 1024 2048 4096 8 - timings 6946 232 16 39 0 160 3 -endmode - -mode "1280x1024-85" - geometry 1280 1024 2048 4096 8 - timings 6538 232 16 39 0 160 3 -endmode diff --git a/Documentation/fb/cyblafb/performance b/Documentation/fb/cyblafb/performance deleted file mode 100644 index 8d15d5dfc6b..00000000000 --- a/Documentation/fb/cyblafb/performance +++ /dev/null @@ -1,79 +0,0 @@ -Speed -===== - -CyBlaFB is much faster than tridentfb and vesafb. Compare the performance data -for mode 1280x1024-[8,16,32]@61 Hz. - -Test 1: Cat a file with 2000 lines of 0 characters. -Test 2: Cat a file with 2000 lines of 80 characters. -Test 3: Cat a file with 2000 lines of 160 characters. - -All values show system time use in seconds, kernel 2.6.12 was used for -the measurements. 2.6.13 is a bit slower, 2.6.14 hopefully will include a -patch that speeds up kernel bitblitting a lot ( > 20%). - -+-----------+-----------------------------------------------------+ -| | not accelerated | -| TRIDENTFB +-----------------+-----------------+-----------------+ -| of 2.6.12 | 8 bpp | 16 bpp | 32 bpp | -| | noypan | ypan | noypan | ypan | noypan | ypan | -+-----------+--------+--------+--------+--------+--------+--------+ -| Test 1 | 4.31 | 4.33 | 6.05 | 12.81 | ---- | ---- | -| Test 2 | 67.94 | 5.44 | 123.16 | 14.79 | ---- | ---- | -| Test 3 | 131.36 | 6.55 | 240.12 | 16.76 | ---- | ---- | -+-----------+--------+--------+--------+--------+--------+--------+ -| Comments | | | completely bro- | -| | | | ken, monitor | -| | | | switches off | -+-----------+-----------------+-----------------+-----------------+ - - -+-----------+-----------------------------------------------------+ -| | accelerated | -| TRIDENTFB +-----------------+-----------------+-----------------+ -| of 2.6.12 | 8 bpp | 16 bpp | 32 bpp | -| | noypan | ypan | noypan | ypan | noypan | ypan | -+-----------+--------+--------+--------+--------+--------+--------+ -| Test 1 | ---- | ---- | 20.62 | 1.22 | ---- | ---- | -| Test 2 | ---- | ---- | 22.61 | 3.19 | ---- | ---- | -| Test 3 | ---- | ---- | 24.59 | 5.16 | ---- | ---- | -+-----------+--------+--------+--------+--------+--------+--------+ -| Comments | broken, writing | broken, ok only | completely bro- | -| | to wrong places | if bgcolor is | ken, monitor | -| | on screen + bug | black, bug in | switches off | -| | in fillrect() | fillrect() | | -+-----------+-----------------+-----------------+-----------------+ - - -+-----------+-----------------------------------------------------+ -| | not accelerated | -| VESAFB +-----------------+-----------------+-----------------+ -| of 2.6.12 | 8 bpp | 16 bpp | 32 bpp | -| | noypan | ypan | noypan | ypan | noypan | ypan | -+-----------+--------+--------+--------+--------+--------+--------+ -| Test 1 | 4.26 | 3.76 | 5.99 | 7.23 | ---- | ---- | -| Test 2 | 65.65 | 4.89 | 120.88 | 9.08 | ---- | ---- | -| Test 3 | 126.91 | 5.94 | 235.77 | 11.03 | ---- | ---- | -+-----------+--------+--------+--------+--------+--------+--------+ -| Comments | vga=0x307 | vga=0x31a | vga=0x31b not | -| | fh=80kHz | fh=80kHz | supported by | -| | fv=75kHz | fv=75kHz | video BIOS and | -| | | | hardware | -+-----------+-----------------+-----------------+-----------------+ - - -+-----------+-----------------------------------------------------+ -| | accelerated | -| CYBLAFB +-----------------+-----------------+-----------------+ -| | 8 bpp | 16 bpp | 32 bpp | -| | noypan | ypan | noypan | ypan | noypan | ypan | -+-----------+--------+--------+--------+--------+--------+--------+ -| Test 1 | 8.02 | 0.23 | 19.04 | 0.61 | 57.12 | 2.74 | -| Test 2 | 8.38 | 0.55 | 19.39 | 0.92 | 57.54 | 3.13 | -| Test 3 | 8.73 | 0.86 | 19.74 | 1.24 | 57.95 | 3.51 | -+-----------+--------+--------+--------+--------+--------+--------+ -| Comments | | | | -| | | | | -| | | | | -| | | | | -+-----------+-----------------+-----------------+-----------------+ diff --git a/Documentation/fb/cyblafb/todo b/Documentation/fb/cyblafb/todo deleted file mode 100644 index c5f6d0eae54..00000000000 --- a/Documentation/fb/cyblafb/todo +++ /dev/null @@ -1,31 +0,0 @@ -TODO / Missing features -======================= - -Verify LCD stuff "stretch" and "center" options are - completely untested ... this code needs to be - verified. As I don't have access to such - hardware, please contact me if you are - willing run some tests. - -Interlaced video modes The reason that interleaved - modes are disabled is that I do not know - the meaning of the vertical interlace - parameter. Also the datasheet mentions a - bit d8 of a horizontal interlace parameter, - but nowhere the lower 8 bits. Please help - if you can. - -low-res double scan modes Who needs it? - -accelerated color blitting Who needs it? The console driver does use color - blitting for nothing but drawing the penguine, - everything else is done using color expanding - blitting of 1bpp character bitmaps. - -ioctls Who needs it? - -TV-out Will be done later. Use "vga= " at boot time - to set a suitable video mode. - -??? Feel free to contact me if you have any - feature requests diff --git a/Documentation/fb/cyblafb/usage b/Documentation/fb/cyblafb/usage deleted file mode 100644 index a39bb3d402a..00000000000 --- a/Documentation/fb/cyblafb/usage +++ /dev/null @@ -1,217 +0,0 @@ -CyBlaFB is a framebuffer driver for the Cyberblade/i1 graphics core integrated -into the VIA Apollo PLE133 (aka vt8601) south bridge. It is developed and -tested using a VIA EPIA 5000 board. - -Cyblafb - compiled into the kernel or as a module? -================================================== - -You might compile cyblafb either as a module or compile it permanently into the -kernel. - -Unless you have a real reason to do so you should not compile both vesafb and -cyblafb permanently into the kernel. It's possible and it helps during the -developement cycle, but it's useless and will at least block some otherwise -usefull memory for ordinary users. - -Selecting Modes -=============== - - Startup Mode - ============ - - First of all, you might use the "vga=???" boot parameter as it is - documented in vesafb.txt and svga.txt. Cyblafb will detect the video - mode selected and will use the geometry and timings found by - inspecting the hardware registers. - - video=cyblafb vga=0x317 - - Alternatively you might use a combination of the mode, ref and bpp - parameters. If you compiled the driver into the kernel, add something - like this to the kernel command line: - - video=cyblafb:1280x1024,bpp=16,ref=50 ... - - If you compiled the driver as a module, the same mode would be - selected by the following command: - - modprobe cyblafb mode=1280x1024 bpp=16 ref=50 ... - - None of the modes possible to select as startup modes are affected by - the problems described at the end of the next subsection. - - For all startup modes cyblafb chooses a virtual x resolution of 2048, - the only exception is mode 1280x1024 in combination with 32 bpp. This - allows ywrap scrolling for all those modes if rotation is 0 or 2, and - also fast scrolling if rotation is 1 or 3. The default virtual y reso- - lution is 4096 for bpp == 8, 2048 for bpp==16 and 1024 for bpp == 32, - again with the only exception of 1280x1024 at 32 bpp. - - Please do set your video memory size to 8 Mb in the Bios setup. Other - values will work, but performace is decreased for a lot of modes. - - Mode changes using fbset - ======================== - - You might use fbset to change the video mode, see "man fbset". Cyblafb - generally does assume that you know what you are doing. But it does - some checks, especially those that are needed to prevent you from - damaging your hardware. - - - only 8, 16, 24 and 32 bpp video modes are accepted - - interlaced video modes are not accepted - - double scan video modes are not accepted - - if a flat panel is found, cyblafb does not allow you - to program a resolution higher than the physical - resolution of the flat panel monitor - - cyblafb does not allow vclk to exceed 230 MHz. As 32 bpp - and (currently) 24 bit modes use a doubled vclk internally, - the dotclock limit as seen by fbset is 115 MHz for those - modes and 230 MHz for 8 and 16 bpp modes. - - cyblafb will allow you to select very high resolutions as - long as the hardware can be programmed to these modes. The - documented limit 1600x1200 is not enforced, but don't expect - perfect signal quality. - - Any request that violates the rules given above will be either changed - to something the hardware supports or an error value will be returned. - - If you program a virtual y resolution higher than the hardware limit, - cyblafb will silently decrease that value to the highest possible - value. The same is true for a virtual x resolution that is not - supported by the hardware. Cyblafb tries to adapt vyres first because - vxres decides if ywrap scrolling is possible or not. - - Attempts to disable acceleration are ignored, I believe that this is - safe. - - Some video modes that should work do not work as expected. If you use - the standard fb.modes, fbset 640x480-60 will program that mode, but - you will see a vertical area, about two characters wide, with only - much darker characters than the other characters on the screen. - Cyblafb does allow that mode to be set, as it does not violate the - official specifications. It would need a lot of code to reliably sort - out all invalid modes, playing around with the margin values will - give a valid mode quickly. And if cyblafb would detect such an invalid - mode, should it silently alter the requested values or should it - report an error? Both options have some pros and cons. As stated - above, none of the startup modes are affected, and if you set - verbosity to 1 or higher, cyblafb will print the fbset command that - would be needed to program that mode using fbset. - - -Other Parameters -================ - - -crt don't autodetect, assume monitor connected to - standard VGA connector - -fp don't autodetect, assume flat panel display - connected to flat panel monitor interface - -nativex inform driver about native x resolution of - flat panel monitor connected to special - interface (should be autodetected) - -stretch stretch image to adapt low resolution modes to - higer resolutions of flat panel monitors - connected to special interface - -center center image to adapt low resolution modes to - higer resolutions of flat panel monitors - connected to special interface - -memsize use if autodetected memsize is wrong ... - should never be necessary - -nopcirr disable PCI read retry -nopciwr disable PCI write retry -nopcirb disable PCI read bursts -nopciwb disable PCI write bursts - -bpp bpp for specified modes - valid values: 8 || 16 || 24 || 32 - -ref refresh rate for specified mode - valid values: 50 <= ref <= 85 - -mode 640x480 or 800x600 or 1024x768 or 1280x1024 - if not specified, the startup mode will be detected - and used, so you might also use the vga=??? parameter - described in vesafb.txt. If you do not specify a mode, - bpp and ref parameters are ignored. - -verbosity 0 is the default, increase to at least 2 for every - bug report! - -Development hints -================= - -It's much faster do compile a module and to load the new version after -unloading the old module than to compile a new kernel and to reboot. So if you -try to work on cyblafb, it might be a good idea to use cyblafb as a module. -In real life, fast often means dangerous, and that's also the case here. If -you introduce a serious bug when cyblafb is compiled into the kernel, the -kernel will lock or oops with a high probability before the file system is -mounted, and the danger for your data is low. If you load a broken own version -of cyblafb on a running system, the danger for the integrity of the file -system is much higher as you might need a hard reset afterwards. Decide -yourself. - -Module unloading, the vfb method -================================ - -If you want to unload/reload cyblafb using the virtual framebuffer, you need -to enable vfb support in the kernel first. After that, load the modules as -shown below: - - modprobe vfb vfb_enable=1 - modprobe fbcon - modprobe cyblafb - fbset -fb /dev/fb1 1280x1024-60 -vyres 2662 - con2fb /dev/fb1 /dev/tty1 - ... - -If you now made some changes to cyblafb and want to reload it, you might do it -as show below: - - con2fb /dev/fb0 /dev/tty1 - ... - rmmod cyblafb - modprobe cyblafb - con2fb /dev/fb1 /dev/tty1 - ... - -Of course, you might choose another mode, and most certainly you also want to -map some other /dev/tty* to the real framebuffer device. You might also choose -to compile fbcon as a kernel module or place it permanently in the kernel. - -I do not know of any way to unload fbcon, and fbcon will prevent the -framebuffer device loaded first from unloading. [If there is a way, then -please add a description here!] - -Module unloading, the vesafb method -=================================== - -Configure the kernel: - - <*> Support for frame buffer devices - [*] VESA VGA graphics support - <M> Cyberblade/i1 support - -Add e.g. "video=vesafb:ypan vga=0x307" to the kernel parameters. The ypan -parameter is important, choose any vga parameter you like as long as it is -a graphics mode. - -After booting, load cyblafb without any mode and bpp parameter and assign -cyblafb to individual ttys using con2fb, e.g.: - - modprobe cyblafb - con2fb /dev/fb1 /dev/tty1 - -Unloading cyblafb works without problems after you assign vesafb to all -ttys again, e.g.: - - con2fb /dev/fb0 /dev/tty1 - rmmod cyblafb diff --git a/Documentation/fb/cyblafb/whatsnew b/Documentation/fb/cyblafb/whatsnew deleted file mode 100644 index 76c07a26e04..00000000000 --- a/Documentation/fb/cyblafb/whatsnew +++ /dev/null @@ -1,29 +0,0 @@ -0.62 -==== - - - the vesafb parameter has been removed as I decided to allow the - feature without any special parameter. - - - Cyblafb does not use the vga style of panning any longer, now the - "right view" register in the graphics engine IO space is used. Without - that change it was impossible to use all available memory, and without - access to all available memory it is impossible to ywrap. - - - The imageblit function now uses hardware acceleration for all font - widths. Hardware blitting across pixel column 2048 is broken in the - cyberblade/i1 graphics core, but we work around that hardware bug. - - - modes with vxres != xres are supported now. - - - ywrap scrolling is supported now and the default. This is a big - performance gain. - - - default video modes use vyres > yres and vxres > xres to allow - almost optimal scrolling speed for normal and rotated screens - - - some features mainly usefull for debugging the upper layers of the - framebuffer system have been added, have a look at the code - - - fixed: Oops after unloading cyblafb when reading /proc/io* - - - we work around some bugs of the higher framebuffer layers. diff --git a/Documentation/fb/cyblafb/whycyblafb b/Documentation/fb/cyblafb/whycyblafb deleted file mode 100644 index a123bc11e69..00000000000 --- a/Documentation/fb/cyblafb/whycyblafb +++ /dev/null @@ -1,85 +0,0 @@ -I tried the following framebuffer drivers: - - - TRIDENTFB is full of bugs. Acceleration is broken for Blade3D - graphics cores like the cyberblade/i1. It claims to support a great - number of devices, but documentation for most of these devices is - unfortunately not available. There is _no_ reason to use tridentfb - for cyberblade/i1 + CRT users. VESAFB is faster, and the one - advantage, mode switching, is broken in tridentfb. - - - VESAFB is used by many distributions as a standard. Vesafb does - not support mode switching. VESAFB is a bit faster than the working - configurations of TRIDENTFB, but it is still too slow, even if you - use ypan. - - - EPIAFB (you'll find it on sourceforge) supports the Cyberblade/i1 - graphics core, but it still has serious bugs and developement seems - to have stopped. This is the one driver with TV-out support. If you - do need this feature, try epiafb. - -None of these drivers was a real option for me. - -I believe that is unreasonable to change code that announces to support 20 -devices if I only have more or less sufficient documentation for exactly one -of these. The risk of breaking device foo while fixing device bar is too high. - -So I decided to start CyBlaFB as a stripped down tridentfb. - -All code specific to other Trident chips has been removed. After that there -were a lot of cosmetic changes to increase the readability of the code. All -register names were changed to those mnemonics used in the datasheet. Function -and macro names were changed if they hindered easy understanding of the code. - -After that I debugged the code and implemented some new features. I'll try to -give a little summary of the main changes: - - - calculation of vertical and horizontal timings was fixed - - - video signal quality has been improved dramatically - - - acceleration: - - - fillrect and copyarea were fixed and reenabled - - - color expanding imageblit was newly implemented, color - imageblit (only used to draw the penguine) still uses the - generic code. - - - init of the acceleration engine was improved and moved to a - place where it really works ... - - - sync function has a timeout now and tries to reset and - reinit the accel engine if necessary - - - fewer slow copyarea calls when doing ypan scrolling by using - undocumented bit d21 of screen start address stored in - CR2B[5]. BIOS does use it also, so this should be safe. - - - cyblafb rejects any attempt to set modes that would cause vclk - values above reasonable 230 MHz. 32bit modes use a clock - multiplicator of 2, so fbset does show the correct values for - pixclock but not for vclk in this case. The fbset limit is 115 MHz - for 32 bpp modes. - - - cyblafb rejects modes known to be broken or unimplemented (all - interlaced modes, all doublescan modes for now) - - - cyblafb now works independant of the video mode in effect at startup - time (tridentfb does not init all needed registers to reasonable - values) - - - switching between video modes does work reliably now - - - the first video mode now is the one selected on startup using the - vga=???? mechanism or any of - - 640x480, 800x600, 1024x768, 1280x1024 - - 8, 16, 24 or 32 bpp - - refresh between 50 Hz and 85 Hz, 1 Hz steps (1280x1024-32 - is limited to 63Hz) - - - pci retry and pci burst mode are settable (try to disable if you - experience latency problems) - - - built as a module cyblafb might be unloaded and reloaded using - the vfb module and con2vt or might be used together with vesafb - diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 7907586c6e0..a23361e80c6 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -64,10 +64,10 @@ Who: Pavel Machek <pavel@suse.cz> --------------------------- -What: Video4Linux API 1 ioctls and video_decoder.h from Video devices. -When: December 2008 -Files: include/linux/video_decoder.h include/linux/videodev.h -Check: include/linux/video_decoder.h include/linux/videodev.h +What: Video4Linux API 1 ioctls and from Video devices. +When: July 2009 +Files: include/linux/videodev.h +Check: include/linux/videodev.h Why: V4L1 AP1 was replaced by V4L2 API during migration from 2.4 to 2.6 series. The old API have lots of drawbacks and don't provide enough means to work with all video and audio standards. The newer API is @@ -255,6 +255,16 @@ Who: Jan Engelhardt <jengelh@computergmbh.de> --------------------------- +What: GPIO autorequest on gpio_direction_{input,output}() in gpiolib +When: February 2010 +Why: All callers should use explicit gpio_request()/gpio_free(). + The autorequest mechanism in gpiolib was provided mostly as a + migration aid for legacy GPIO interfaces (for SOC based GPIOs). + Those users have now largely migrated. Platforms implementing + the GPIO interfaces without using gpiolib will see no changes. +Who: David Brownell <dbrownell@users.sourceforge.net> +--------------------------- + What: b43 support for firmware revision < 410 When: The schedule was July 2008, but it was decided that we are going to keep the code as long as there are no major maintanance headaches. @@ -311,6 +321,18 @@ Who: Vlad Yasevich <vladislav.yasevich@hp.com> --------------------------- +What: Ability for non root users to shm_get hugetlb pages based on mlock + resource limits +When: 2.6.31 +Why: Non root users need to be part of /proc/sys/vm/hugetlb_shm_group or + have CAP_IPC_LOCK to be able to allocate shm segments backed by + huge pages. The mlock based rlimit check to allow shm hugetlb is + inconsistent with mmap based allocations. Hence it is being + deprecated. +Who: Ravikiran Thirumalai <kiran@scalex86.org> + +--------------------------- + What: CONFIG_THERMAL_HWMON When: January 2009 Why: This option was introduced just to allow older lm-sensors userspace @@ -356,17 +378,6 @@ Who: Hans de Goede <hdegoede@redhat.com> --------------------------- -What: SELinux "compat_net" functionality -When: 2.6.30 at the earliest -Why: In 2.6.18 the Secmark concept was introduced to replace the "compat_net" - network access control functionality of SELinux. Secmark offers both - better performance and greater flexibility than the "compat_net" - mechanism. Now that the major Linux distributions have moved to - Secmark, it is time to deprecate the older mechanism and start the - process of removing the old code. -Who: Paul Moore <paul.moore@hp.com> ---------------------------- - What: sysfs ui for changing p4-clockmod parameters When: September 2009 Why: See commits 129f8ae9b1b5be94517da76009ea956e89104ce8 and @@ -391,3 +402,35 @@ Why: The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have been kept around for migration reasons. After more than two years it's time to remove them finally Who: Thomas Gleixner <tglx@linutronix.de> + +--------------------------- + +What: fakephp and associated sysfs files in /sys/bus/pci/slots/ +When: 2011 +Why: In 2.6.27, the semantics of /sys/bus/pci/slots was redefined to + represent a machine's physical PCI slots. The change in semantics + had userspace implications, as the hotplug core no longer allowed + drivers to create multiple sysfs files per physical slot (required + for multi-function devices, e.g.). fakephp was seen as a developer's + tool only, and its interface changed. Too late, we learned that + there were some users of the fakephp interface. + + In 2.6.30, the original fakephp interface was restored. At the same + time, the PCI core gained the ability that fakephp provided, namely + function-level hot-remove and hot-add. + + Since the PCI core now provides the same functionality, exposed in: + + /sys/bus/pci/rescan + /sys/bus/pci/devices/.../remove + /sys/bus/pci/devices/.../rescan + + there is no functional reason to maintain fakephp as well. + + We will keep the existing module so that 'modprobe fakephp' will + present the old /sys/bus/pci/slots/... interface for compatibility, + but users are urged to migrate their applications to the API above. + + After a reasonable transition period, we will remove the legacy + fakephp interface. +Who: Alex Chiang <achiang@hp.com> diff --git a/Documentation/filesystems/Locking b/Documentation/filesystems/Locking index 4e78ce67784..76efe5b71d7 100644 --- a/Documentation/filesystems/Locking +++ b/Documentation/filesystems/Locking @@ -505,7 +505,7 @@ prototypes: void (*open)(struct vm_area_struct*); void (*close)(struct vm_area_struct*); int (*fault)(struct vm_area_struct*, struct vm_fault *); - int (*page_mkwrite)(struct vm_area_struct *, struct page *); + int (*page_mkwrite)(struct vm_area_struct *, struct vm_fault *); int (*access)(struct vm_area_struct *, unsigned long, void*, int, int); locking rules: diff --git a/Documentation/filesystems/ext4.txt b/Documentation/filesystems/ext4.txt index cec829bc729..97882df0486 100644 --- a/Documentation/filesystems/ext4.txt +++ b/Documentation/filesystems/ext4.txt @@ -85,7 +85,7 @@ Note: More extensive information for getting started with ext4 can be * extent format more robust in face of on-disk corruption due to magics, * internal redundancy in tree * improved file allocation (multi-block alloc) -* fix 32000 subdirectory limit +* lift 32000 subdirectory limit imposed by i_links_count[1] * nsec timestamps for mtime, atime, ctime, create time * inode version field on disk (NFSv4, Lustre) * reduced e2fsck time via uninit_bg feature @@ -100,6 +100,9 @@ Note: More extensive information for getting started with ext4 can be * efficent new ordered mode in JBD2 and ext4(avoid using buffer head to force the ordering) +[1] Filesystems with a block size of 1k may see a limit imposed by the +directory hash tree having a maximum depth of two. + 2.2 Candidate features for future inclusion * Online defrag (patches available but not well tested) @@ -180,8 +183,8 @@ commit=nrsec (*) Ext4 can be told to sync all its data and metadata performance. barrier=<0|1(*)> This enables/disables the use of write barriers in - the jbd code. barrier=0 disables, barrier=1 enables. - This also requires an IO stack which can support +barrier(*) the jbd code. barrier=0 disables, barrier=1 enables. +nobarrier This also requires an IO stack which can support barriers, and if jbd gets an error on a barrier write, it will disable again with a warning. Write barriers enforce proper on-disk ordering @@ -189,6 +192,9 @@ barrier=<0|1(*)> This enables/disables the use of write barriers in safe to use, at some performance penalty. If your disks are battery-backed in one way or another, disabling barriers may safely improve performance. + The mount options "barrier" and "nobarrier" can + also be used to enable or disable barriers, for + consistency with other ext4 mount options. inode_readahead=n This tuning parameter controls the maximum number of inode table blocks that ext4's inode @@ -310,6 +316,24 @@ journal_ioprio=prio The I/O priority (from 0 to 7, where 0 is the a slightly higher priority than the default I/O priority. +auto_da_alloc(*) Many broken applications don't use fsync() when +noauto_da_alloc replacing existing files via patterns such as + fd = open("foo.new")/write(fd,..)/close(fd)/ + rename("foo.new", "foo"), or worse yet, + fd = open("foo", O_TRUNC)/write(fd,..)/close(fd). + If auto_da_alloc is enabled, ext4 will detect + the replace-via-rename and replace-via-truncate + patterns and force that any delayed allocation + blocks are allocated such that at the next + journal commit, in the default data=ordered + mode, the data blocks of the new file are forced + to disk before the rename() operation is + commited. This provides roughly the same level + of guarantees as ext3, and avoids the + "zero-length" problem that can happen when a + system crashes before the delayed allocation + blocks are forced to disk. + Data Mode ========= There are 3 different data modes: diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt index 830bad7cce0..ce84cfc9eae 100644 --- a/Documentation/filesystems/proc.txt +++ b/Documentation/filesystems/proc.txt @@ -5,6 +5,7 @@ Bodo Bauer <bb@ricochet.net> 2.4.x update Jorge Nerin <comandante@zaralinux.com> November 14 2000 +move /proc/sys Shen Feng <shen@cn.fujitsu.com> April 1 2009 ------------------------------------------------------------------------------ Version 1.3 Kernel version 2.2.12 Kernel version 2.4.0-test11-pre4 @@ -26,25 +27,17 @@ Table of Contents 1.6 Parallel port info in /proc/parport 1.7 TTY info in /proc/tty 1.8 Miscellaneous kernel statistics in /proc/stat + 1.9 Ext4 file system parameters 2 Modifying System Parameters - 2.1 /proc/sys/fs - File system data - 2.2 /proc/sys/fs/binfmt_misc - Miscellaneous binary formats - 2.3 /proc/sys/kernel - general kernel parameters - 2.4 /proc/sys/vm - The virtual memory subsystem - 2.5 /proc/sys/dev - Device specific parameters - 2.6 /proc/sys/sunrpc - Remote procedure calls - 2.7 /proc/sys/net - Networking stuff - 2.8 /proc/sys/net/ipv4 - IPV4 settings - 2.9 Appletalk - 2.10 IPX - 2.11 /proc/sys/fs/mqueue - POSIX message queues filesystem - 2.12 /proc/<pid>/oom_adj - Adjust the oom-killer score - 2.13 /proc/<pid>/oom_score - Display current oom-killer score - 2.14 /proc/<pid>/io - Display the IO accounting fields - 2.15 /proc/<pid>/coredump_filter - Core dump filtering settings - 2.16 /proc/<pid>/mountinfo - Information about mounts - 2.17 /proc/sys/fs/epoll - Configuration options for the epoll interface + + 3 Per-Process Parameters + 3.1 /proc/<pid>/oom_adj - Adjust the oom-killer score + 3.2 /proc/<pid>/oom_score - Display current oom-killer score + 3.3 /proc/<pid>/io - Display the IO accounting fields + 3.4 /proc/<pid>/coredump_filter - Core dump filtering settings + 3.5 /proc/<pid>/mountinfo - Information about mounts + ------------------------------------------------------------------------------ Preface @@ -940,27 +933,6 @@ Table 1-10: Files in /proc/fs/ext4/<devname> File Content mb_groups details of multiblock allocator buddy cache of free blocks mb_history multiblock allocation history - stats controls whether the multiblock allocator should start - collecting statistics, which are shown during the unmount - group_prealloc the multiblock allocator will round up allocation - requests to a multiple of this tuning parameter if the - stripe size is not set in the ext4 superblock - max_to_scan The maximum number of extents the multiblock allocator - will search to find the best extent - min_to_scan The minimum number of extents the multiblock allocator - will search to find the best extent - order2_req Tuning parameter which controls the minimum size for - requests (as a power of 2) where the buddy cache is - used - stream_req Files which have fewer blocks than this tunable - parameter will have their blocks allocated out of a - block group specific preallocation pool, so that small - files are packed closely together. Each large file - will have its blocks allocated out of its own unique - preallocation pool. -inode_readahead Tuning parameter which controls the maximum number of - inode table blocks that ext4's inode table readahead - algorithm will pre-read into the buffer cache .............................................................................. @@ -1011,1021 +983,24 @@ review the kernel documentation in the directory /usr/src/linux/Documentation. This chapter is heavily based on the documentation included in the pre 2.2 kernels, and became part of it in version 2.2.1 of the Linux kernel. -2.1 /proc/sys/fs - File system data ------------------------------------ - -This subdirectory contains specific file system, file handle, inode, dentry -and quota information. - -Currently, these files are in /proc/sys/fs: - -dentry-state ------------- - -Status of the directory cache. Since directory entries are dynamically -allocated and deallocated, this file indicates the current status. It holds -six values, in which the last two are not used and are always zero. The others -are listed in table 2-1. - - -Table 2-1: Status files of the directory cache -.............................................................................. - File Content - nr_dentry Almost always zero - nr_unused Number of unused cache entries - age_limit - in seconds after the entry may be reclaimed, when memory is short - want_pages internally -.............................................................................. - -dquot-nr and dquot-max ----------------------- - -The file dquot-max shows the maximum number of cached disk quota entries. - -The file dquot-nr shows the number of allocated disk quota entries and the -number of free disk quota entries. - -If the number of available cached disk quotas is very low and you have a large -number of simultaneous system users, you might want to raise the limit. - -file-nr and file-max --------------------- - -The kernel allocates file handles dynamically, but doesn't free them again at -this time. - -The value in file-max denotes the maximum number of file handles that the -Linux kernel will allocate. When you get a lot of error messages about running -out of file handles, you might want to raise this limit. The default value is -10% of RAM in kilobytes. To change it, just write the new number into the -file: - - # cat /proc/sys/fs/file-max - 4096 - # echo 8192 > /proc/sys/fs/file-max - # cat /proc/sys/fs/file-max - 8192 - - -This method of revision is useful for all customizable parameters of the -kernel - simply echo the new value to the corresponding file. - -Historically, the three values in file-nr denoted the number of allocated file -handles, the number of allocated but unused file handles, and the maximum -number of file handles. Linux 2.6 always reports 0 as the number of free file -handles -- this is not an error, it just means that the number of allocated -file handles exactly matches the number of used file handles. - -Attempts to allocate more file descriptors than file-max are reported with -printk, look for "VFS: file-max limit <number> reached". - -inode-state and inode-nr ------------------------- - -The file inode-nr contains the first two items from inode-state, so we'll skip -to that file... - -inode-state contains two actual numbers and five dummy values. The numbers -are nr_inodes and nr_free_inodes (in order of appearance). - -nr_inodes -~~~~~~~~~ - -Denotes the number of inodes the system has allocated. This number will -grow and shrink dynamically. - -nr_open -------- - -Denotes the maximum number of file-handles a process can -allocate. Default value is 1024*1024 (1048576) which should be -enough for most machines. Actual limit depends on RLIMIT_NOFILE -resource limit. - -nr_free_inodes --------------- - -Represents the number of free inodes. Ie. The number of inuse inodes is -(nr_inodes - nr_free_inodes). - -aio-nr and aio-max-nr ---------------------- - -aio-nr is the running total of the number of events specified on the -io_setup system call for all currently active aio contexts. If aio-nr -reaches aio-max-nr then io_setup will fail with EAGAIN. Note that -raising aio-max-nr does not result in the pre-allocation or re-sizing -of any kernel data structures. - -2.2 /proc/sys/fs/binfmt_misc - Miscellaneous binary formats ------------------------------------------------------------ - -Besides these files, there is the subdirectory /proc/sys/fs/binfmt_misc. This -handles the kernel support for miscellaneous binary formats. - -Binfmt_misc provides the ability to register additional binary formats to the -Kernel without compiling an additional module/kernel. Therefore, binfmt_misc -needs to know magic numbers at the beginning or the filename extension of the -binary. - -It works by maintaining a linked list of structs that contain a description of -a binary format, including a magic with size (or the filename extension), -offset and mask, and the interpreter name. On request it invokes the given -interpreter with the original program as argument, as binfmt_java and -binfmt_em86 and binfmt_mz do. Since binfmt_misc does not define any default -binary-formats, you have to register an additional binary-format. - -There are two general files in binfmt_misc and one file per registered format. -The two general files are register and status. - -Registering a new binary format -------------------------------- - -To register a new binary format you have to issue the command - - echo :name:type:offset:magic:mask:interpreter: > /proc/sys/fs/binfmt_misc/register - - - -with appropriate name (the name for the /proc-dir entry), offset (defaults to -0, if omitted), magic, mask (which can be omitted, defaults to all 0xff) and -last but not least, the interpreter that is to be invoked (for example and -testing /bin/echo). Type can be M for usual magic matching or E for filename -extension matching (give extension in place of magic). - -Check or reset the status of the binary format handler ------------------------------------------------------- - -If you do a cat on the file /proc/sys/fs/binfmt_misc/status, you will get the -current status (enabled/disabled) of binfmt_misc. Change the status by echoing -0 (disables) or 1 (enables) or -1 (caution: this clears all previously -registered binary formats) to status. For example echo 0 > status to disable -binfmt_misc (temporarily). - -Status of a single handler --------------------------- - -Each registered handler has an entry in /proc/sys/fs/binfmt_misc. These files -perform the same function as status, but their scope is limited to the actual -binary format. By cating this file, you also receive all related information -about the interpreter/magic of the binfmt. - -Example usage of binfmt_misc (emulate binfmt_java) --------------------------------------------------- - - cd /proc/sys/fs/binfmt_misc - echo ':Java:M::\xca\xfe\xba\xbe::/usr/local/java/bin/javawrapper:' > register - echo ':HTML:E::html::/usr/local/java/bin/appletviewer:' > register - echo ':Applet:M::<!--applet::/usr/local/java/bin/appletviewer:' > register - echo ':DEXE:M::\x0eDEX::/usr/bin/dosexec:' > register - - -These four lines add support for Java executables and Java applets (like -binfmt_java, additionally recognizing the .html extension with no need to put -<!--applet> to every applet file). You have to install the JDK and the -shell-script /usr/local/java/bin/javawrapper too. It works around the -brokenness of the Java filename handling. To add a Java binary, just create a -link to the class-file somewhere in the path. - -2.3 /proc/sys/kernel - general kernel parameters ------------------------------------------------- - -This directory reflects general kernel behaviors. As I've said before, the -contents depend on your configuration. Here you'll find the most important -files, along with descriptions of what they mean and how to use them. - -acct ----- - -The file contains three values; highwater, lowwater, and frequency. - -It exists only when BSD-style process accounting is enabled. These values -control its behavior. If the free space on the file system where the log lives -goes below lowwater percentage, accounting suspends. If it goes above -highwater percentage, accounting resumes. Frequency determines how often you -check the amount of free space (value is in seconds). Default settings are: 4, -2, and 30. That is, suspend accounting if there is less than 2 percent free; -resume it if we have a value of 3 or more percent; consider information about -the amount of free space valid for 30 seconds - -ctrl-alt-del ------------- - -When the value in this file is 0, ctrl-alt-del is trapped and sent to the init -program to handle a graceful restart. However, when the value is greater that -zero, Linux's reaction to this key combination will be an immediate reboot, -without syncing its dirty buffers. - -[NOTE] - When a program (like dosemu) has the keyboard in raw mode, the - ctrl-alt-del is intercepted by the program before it ever reaches the - kernel tty layer, and it is up to the program to decide what to do with - it. - -domainname and hostname ------------------------ - -These files can be controlled to set the NIS domainname and hostname of your -box. For the classic darkstar.frop.org a simple: - - # echo "darkstar" > /proc/sys/kernel/hostname - # echo "frop.org" > /proc/sys/kernel/domainname - - -would suffice to set your hostname and NIS domainname. - -osrelease, ostype and version ------------------------------ - -The names make it pretty obvious what these fields contain: - - > cat /proc/sys/kernel/osrelease - 2.2.12 - - > cat /proc/sys/kernel/ostype - Linux - - > cat /proc/sys/kernel/version - #4 Fri Oct 1 12:41:14 PDT 1999 - - -The files osrelease and ostype should be clear enough. Version needs a little -more clarification. The #4 means that this is the 4th kernel built from this -source base and the date after it indicates the time the kernel was built. The -only way to tune these values is to rebuild the kernel. - -panic ------ - -The value in this file represents the number of seconds the kernel waits -before rebooting on a panic. When you use the software watchdog, the -recommended setting is 60. If set to 0, the auto reboot after a kernel panic -is disabled, which is the default setting. - -printk ------- - -The four values in printk denote -* console_loglevel, -* default_message_loglevel, -* minimum_console_loglevel and -* default_console_loglevel -respectively. - -These values influence printk() behavior when printing or logging error -messages, which come from inside the kernel. See syslog(2) for more -information on the different log levels. - -console_loglevel ----------------- - -Messages with a higher priority than this will be printed to the console. - -default_message_level ---------------------- - -Messages without an explicit priority will be printed with this priority. - -minimum_console_loglevel ------------------------- - -Minimum (highest) value to which the console_loglevel can be set. - -default_console_loglevel ------------------------- - -Default value for console_loglevel. - -sg-big-buff ------------ - -This file shows the size of the generic SCSI (sg) buffer. At this point, you -can't tune it yet, but you can change it at compile time by editing -include/scsi/sg.h and changing the value of SG_BIG_BUFF. - -If you use a scanner with SANE (Scanner Access Now Easy) you might want to set -this to a higher value. Refer to the SANE documentation on this issue. - -modprobe --------- - -The location where the modprobe binary is located. The kernel uses this -program to load modules on demand. - -unknown_nmi_panic ------------------ - -The value in this file affects behavior of handling NMI. When the value is -non-zero, unknown NMI is trapped and then panic occurs. At that time, kernel -debugging information is displayed on console. - -NMI switch that most IA32 servers have fires unknown NMI up, for example. -If a system hangs up, try pressing the NMI switch. - -panic_on_unrecovered_nmi ------------------------- - -The default Linux behaviour on an NMI of either memory or unknown is to continue -operation. For many environments such as scientific computing it is preferable -that the box is taken out and the error dealt with than an uncorrected -parity/ECC error get propogated. - -A small number of systems do generate NMI's for bizarre random reasons such as -power management so the default is off. That sysctl works like the existing -panic controls already in that directory. - -nmi_watchdog ------------- - -Enables/Disables the NMI watchdog on x86 systems. When the value is non-zero -the NMI watchdog is enabled and will continuously test all online cpus to -determine whether or not they are still functioning properly. Currently, -passing "nmi_watchdog=" parameter at boot time is required for this function -to work. - -If LAPIC NMI watchdog method is in use (nmi_watchdog=2 kernel parameter), the -NMI watchdog shares registers with oprofile. By disabling the NMI watchdog, -oprofile may have more registers to utilize. - -msgmni ------- - -Maximum number of message queue ids on the system. -This value scales to the amount of lowmem. It is automatically recomputed -upon memory add/remove or ipc namespace creation/removal. -When a value is written into this file, msgmni's value becomes fixed, i.e. it -is not recomputed anymore when one of the above events occurs. -Use auto_msgmni to change this behavior. - -auto_msgmni ------------ - -Enables/Disables automatic recomputing of msgmni upon memory add/remove or -upon ipc namespace creation/removal (see the msgmni description above). -Echoing "1" into this file enables msgmni automatic recomputing. -Echoing "0" turns it off. -auto_msgmni default value is 1. - - -2.4 /proc/sys/vm - The virtual memory subsystem ------------------------------------------------ - -Please see: Documentation/sysctls/vm.txt for a description of these +Please see: Documentation/sysctls/ directory for descriptions of these entries. +------------------------------------------------------------------------------ +Summary +------------------------------------------------------------------------------ +Certain aspects of kernel behavior can be modified at runtime, without the +need to recompile the kernel, or even to reboot the system. The files in the +/proc/sys tree can not only be read, but also modified. You can use the echo +command to write value into these files, thereby changing the default settings +of the kernel. +------------------------------------------------------------------------------ -2.5 /proc/sys/dev - Device specific parameters ----------------------------------------------- - -Currently there is only support for CDROM drives, and for those, there is only -one read-only file containing information about the CD-ROM drives attached to -the system: - - >cat /proc/sys/dev/cdrom/info - CD-ROM information, Id: cdrom.c 2.55 1999/04/25 - - drive name: sr0 hdb - drive speed: 32 40 - drive # of slots: 1 0 - Can close tray: 1 1 - Can open tray: 1 1 - Can lock tray: 1 1 - Can change speed: 1 1 - Can select disk: 0 1 - Can read multisession: 1 1 - Can read MCN: 1 1 - Reports media changed: 1 1 - Can play audio: 1 1 - - -You see two drives, sr0 and hdb, along with a list of their features. - -2.6 /proc/sys/sunrpc - Remote procedure calls ---------------------------------------------- - -This directory contains four files, which enable or disable debugging for the -RPC functions NFS, NFS-daemon, RPC and NLM. The default values are 0. They can -be set to one to turn debugging on. (The default value is 0 for each) - -2.7 /proc/sys/net - Networking stuff ------------------------------------- - -The interface to the networking parts of the kernel is located in -/proc/sys/net. Table 2-3 shows all possible subdirectories. You may see only -some of them, depending on your kernel's configuration. - - -Table 2-3: Subdirectories in /proc/sys/net -.............................................................................. - Directory Content Directory Content - core General parameter appletalk Appletalk protocol - unix Unix domain sockets netrom NET/ROM - 802 E802 protocol ax25 AX25 - ethernet Ethernet protocol rose X.25 PLP layer - ipv4 IP version 4 x25 X.25 protocol - ipx IPX token-ring IBM token ring - bridge Bridging decnet DEC net - ipv6 IP version 6 -.............................................................................. - -We will concentrate on IP networking here. Since AX15, X.25, and DEC Net are -only minor players in the Linux world, we'll skip them in this chapter. You'll -find some short info on Appletalk and IPX further on in this chapter. Review -the online documentation and the kernel source to get a detailed view of the -parameters for those protocols. In this section we'll discuss the -subdirectories printed in bold letters in the table above. As default values -are suitable for most needs, there is no need to change these values. - -/proc/sys/net/core - Network core options ------------------------------------------ - -rmem_default ------------- - -The default setting of the socket receive buffer in bytes. - -rmem_max --------- - -The maximum receive socket buffer size in bytes. - -wmem_default ------------- - -The default setting (in bytes) of the socket send buffer. - -wmem_max --------- - -The maximum send socket buffer size in bytes. - -message_burst and message_cost ------------------------------- - -These parameters are used to limit the warning messages written to the kernel -log from the networking code. They enforce a rate limit to make a -denial-of-service attack impossible. A higher message_cost factor, results in -fewer messages that will be written. Message_burst controls when messages will -be dropped. The default settings limit warning messages to one every five -seconds. - -warnings --------- - -This controls console messages from the networking stack that can occur because -of problems on the network like duplicate address or bad checksums. Normally, -this should be enabled, but if the problem persists the messages can be -disabled. - -netdev_budget -------------- - -Maximum number of packets taken from all interfaces in one polling cycle (NAPI -poll). In one polling cycle interfaces which are registered to polling are -probed in a round-robin manner. The limit of packets in one such probe can be -set per-device via sysfs class/net/<device>/weight . - -netdev_max_backlog ------------------- - -Maximum number of packets, queued on the INPUT side, when the interface -receives packets faster than kernel can process them. - -optmem_max ----------- - -Maximum ancillary buffer size allowed per socket. Ancillary data is a sequence -of struct cmsghdr structures with appended data. - -/proc/sys/net/unix - Parameters for Unix domain sockets -------------------------------------------------------- - -There are only two files in this subdirectory. They control the delays for -deleting and destroying socket descriptors. - -2.8 /proc/sys/net/ipv4 - IPV4 settings --------------------------------------- - -IP version 4 is still the most used protocol in Unix networking. It will be -replaced by IP version 6 in the next couple of years, but for the moment it's -the de facto standard for the internet and is used in most networking -environments around the world. Because of the importance of this protocol, -we'll have a deeper look into the subtree controlling the behavior of the IPv4 -subsystem of the Linux kernel. - -Let's start with the entries in /proc/sys/net/ipv4. - -ICMP settings -------------- - -icmp_echo_ignore_all and icmp_echo_ignore_broadcasts ----------------------------------------------------- - -Turn on (1) or off (0), if the kernel should ignore all ICMP ECHO requests, or -just those to broadcast and multicast addresses. - -Please note that if you accept ICMP echo requests with a broadcast/multi\-cast -destination address your network may be used as an exploder for denial of -service packet flooding attacks to other hosts. - -icmp_destunreach_rate, icmp_echoreply_rate, icmp_paramprob_rate and icmp_timeexeed_rate ---------------------------------------------------------------------------------------- - -Sets limits for sending ICMP packets to specific targets. A value of zero -disables all limiting. Any positive value sets the maximum package rate in -hundredth of a second (on Intel systems). - -IP settings ------------ - -ip_autoconfig -------------- - -This file contains the number one if the host received its IP configuration by -RARP, BOOTP, DHCP or a similar mechanism. Otherwise it is zero. - -ip_default_ttl --------------- - -TTL (Time To Live) for IPv4 interfaces. This is simply the maximum number of -hops a packet may travel. - -ip_dynaddr ----------- - -Enable dynamic socket address rewriting on interface address change. This is -useful for dialup interface with changing IP addresses. - -ip_forward ----------- - -Enable or disable forwarding of IP packages between interfaces. Changing this -value resets all other parameters to their default values. They differ if the -kernel is configured as host or router. - -ip_local_port_range -------------------- - -Range of ports used by TCP and UDP to choose the local port. Contains two -numbers, the first number is the lowest port, the second number the highest -local port. Default is 1024-4999. Should be changed to 32768-61000 for -high-usage systems. - -ip_no_pmtu_disc ---------------- - -Global switch to turn path MTU discovery off. It can also be set on a per -socket basis by the applications or on a per route basis. - -ip_masq_debug -------------- - -Enable/disable debugging of IP masquerading. - -IP fragmentation settings -------------------------- - -ipfrag_high_trash and ipfrag_low_trash --------------------------------------- - -Maximum memory used to reassemble IP fragments. When ipfrag_high_thresh bytes -of memory is allocated for this purpose, the fragment handler will toss -packets until ipfrag_low_thresh is reached. - -ipfrag_time ------------ - -Time in seconds to keep an IP fragment in memory. - -TCP settings ------------- - -tcp_ecn -------- - -This file controls the use of the ECN bit in the IPv4 headers. This is a new -feature about Explicit Congestion Notification, but some routers and firewalls -block traffic that has this bit set, so it could be necessary to echo 0 to -/proc/sys/net/ipv4/tcp_ecn if you want to talk to these sites. For more info -you could read RFC2481. - -tcp_retrans_collapse --------------------- - -Bug-to-bug compatibility with some broken printers. On retransmit, try to send -larger packets to work around bugs in certain TCP stacks. Can be turned off by -setting it to zero. - -tcp_keepalive_probes --------------------- - -Number of keep alive probes TCP sends out, until it decides that the -connection is broken. - -tcp_keepalive_time ------------------- - -How often TCP sends out keep alive messages, when keep alive is enabled. The -default is 2 hours. - -tcp_syn_retries ---------------- - -Number of times initial SYNs for a TCP connection attempt will be -retransmitted. Should not be higher than 255. This is only the timeout for -outgoing connections, for incoming connections the number of retransmits is -defined by tcp_retries1. - -tcp_sack --------- - -Enable select acknowledgments after RFC2018. - -tcp_timestamps --------------- - -Enable timestamps as defined in RFC1323. - -tcp_stdurg ----------- - -Enable the strict RFC793 interpretation of the TCP urgent pointer field. The -default is to use the BSD compatible interpretation of the urgent pointer -pointing to the first byte after the urgent data. The RFC793 interpretation is -to have it point to the last byte of urgent data. Enabling this option may -lead to interoperability problems. Disabled by default. - -tcp_syncookies --------------- - -Only valid when the kernel was compiled with CONFIG_SYNCOOKIES. Send out -syncookies when the syn backlog queue of a socket overflows. This is to ward -off the common 'syn flood attack'. Disabled by default. - -Note that the concept of a socket backlog is abandoned. This means the peer -may not receive reliable error messages from an over loaded server with -syncookies enabled. - -tcp_window_scaling ------------------- - -Enable window scaling as defined in RFC1323. - -tcp_fin_timeout ---------------- - -The length of time in seconds it takes to receive a final FIN before the -socket is always closed. This is strictly a violation of the TCP -specification, but required to prevent denial-of-service attacks. - -tcp_max_ka_probes ------------------ - -Indicates how many keep alive probes are sent per slow timer run. Should not -be set too high to prevent bursts. - -tcp_max_syn_backlog -------------------- - -Length of the per socket backlog queue. Since Linux 2.2 the backlog specified -in listen(2) only specifies the length of the backlog queue of already -established sockets. When more connection requests arrive Linux starts to drop -packets. When syncookies are enabled the packets are still answered and the -maximum queue is effectively ignored. - -tcp_retries1 ------------- - -Defines how often an answer to a TCP connection request is retransmitted -before giving up. - -tcp_retries2 ------------- - -Defines how often a TCP packet is retransmitted before giving up. - -Interface specific settings ---------------------------- - -In the directory /proc/sys/net/ipv4/conf you'll find one subdirectory for each -interface the system knows about and one directory calls all. Changes in the -all subdirectory affect all interfaces, whereas changes in the other -subdirectories affect only one interface. All directories have the same -entries: - -accept_redirects ----------------- - -This switch decides if the kernel accepts ICMP redirect messages or not. The -default is 'yes' if the kernel is configured for a regular host and 'no' for a -router configuration. - -accept_source_route -------------------- - -Should source routed packages be accepted or declined. The default is -dependent on the kernel configuration. It's 'yes' for routers and 'no' for -hosts. - -bootp_relay -~~~~~~~~~~~ - -Accept packets with source address 0.b.c.d with destinations not to this host -as local ones. It is supposed that a BOOTP relay daemon will catch and forward -such packets. - -The default is 0, since this feature is not implemented yet (kernel version -2.2.12). - -forwarding ----------- - -Enable or disable IP forwarding on this interface. - -log_martians ------------- - -Log packets with source addresses with no known route to kernel log. - -mc_forwarding -------------- - -Do multicast routing. The kernel needs to be compiled with CONFIG_MROUTE and a -multicast routing daemon is required. - -proxy_arp ---------- - -Does (1) or does not (0) perform proxy ARP. - -rp_filter ---------- - -Integer value determines if a source validation should be made. 1 means yes, 0 -means no. Disabled by default, but local/broadcast address spoofing is always -on. - -If you set this to 1 on a router that is the only connection for a network to -the net, it will prevent spoofing attacks against your internal networks -(external addresses can still be spoofed), without the need for additional -firewall rules. - -secure_redirects ----------------- - -Accept ICMP redirect messages only for gateways, listed in default gateway -list. Enabled by default. - -shared_media ------------- - -If it is not set the kernel does not assume that different subnets on this -device can communicate directly. Default setting is 'yes'. - -send_redirects --------------- - -Determines whether to send ICMP redirects to other hosts. - -Routing settings ----------------- - -The directory /proc/sys/net/ipv4/route contains several file to control -routing issues. - -error_burst and error_cost --------------------------- - -These parameters are used to limit how many ICMP destination unreachable to -send from the host in question. ICMP destination unreachable messages are -sent when we cannot reach the next hop while trying to transmit a packet. -It will also print some error messages to kernel logs if someone is ignoring -our ICMP redirects. The higher the error_cost factor is, the fewer -destination unreachable and error messages will be let through. Error_burst -controls when destination unreachable messages and error messages will be -dropped. The default settings limit warning messages to five every second. - -flush ------ - -Writing to this file results in a flush of the routing cache. - -gc_elasticity, gc_interval, gc_min_interval_ms, gc_timeout, gc_thresh ---------------------------------------------------------------------- - -Values to control the frequency and behavior of the garbage collection -algorithm for the routing cache. gc_min_interval is deprecated and replaced -by gc_min_interval_ms. - - -max_size --------- - -Maximum size of the routing cache. Old entries will be purged once the cache -reached has this size. - -redirect_load, redirect_number ------------------------------- - -Factors which determine if more ICPM redirects should be sent to a specific -host. No redirects will be sent once the load limit or the maximum number of -redirects has been reached. - -redirect_silence ----------------- - -Timeout for redirects. After this period redirects will be sent again, even if -this has been stopped, because the load or number limit has been reached. - -Network Neighbor handling -------------------------- - -Settings about how to handle connections with direct neighbors (nodes attached -to the same link) can be found in the directory /proc/sys/net/ipv4/neigh. - -As we saw it in the conf directory, there is a default subdirectory which -holds the default values, and one directory for each interface. The contents -of the directories are identical, with the single exception that the default -settings contain additional options to set garbage collection parameters. - -In the interface directories you'll find the following entries: - -base_reachable_time, base_reachable_time_ms -------------------------------------------- - -A base value used for computing the random reachable time value as specified -in RFC2461. - -Expression of base_reachable_time, which is deprecated, is in seconds. -Expression of base_reachable_time_ms is in milliseconds. - -retrans_time, retrans_time_ms ------------------------------ - -The time between retransmitted Neighbor Solicitation messages. -Used for address resolution and to determine if a neighbor is -unreachable. - -Expression of retrans_time, which is deprecated, is in 1/100 seconds (for -IPv4) or in jiffies (for IPv6). -Expression of retrans_time_ms is in milliseconds. - -unres_qlen ----------- - -Maximum queue length for a pending arp request - the number of packets which -are accepted from other layers while the ARP address is still resolved. - -anycast_delay -------------- - -Maximum for random delay of answers to neighbor solicitation messages in -jiffies (1/100 sec). Not yet implemented (Linux does not have anycast support -yet). - -ucast_solicit -------------- - -Maximum number of retries for unicast solicitation. - -mcast_solicit -------------- - -Maximum number of retries for multicast solicitation. - -delay_first_probe_time ----------------------- - -Delay for the first time probe if the neighbor is reachable. (see -gc_stale_time) - -locktime --------- - -An ARP/neighbor entry is only replaced with a new one if the old is at least -locktime old. This prevents ARP cache thrashing. - -proxy_delay ------------ - -Maximum time (real time is random [0..proxytime]) before answering to an ARP -request for which we have an proxy ARP entry. In some cases, this is used to -prevent network flooding. - -proxy_qlen ----------- - -Maximum queue length of the delayed proxy arp timer. (see proxy_delay). - -app_solicit ----------- - -Determines the number of requests to send to the user level ARP daemon. Use 0 -to turn off. - -gc_stale_time -------------- - -Determines how often to check for stale ARP entries. After an ARP entry is -stale it will be resolved again (which is useful when an IP address migrates -to another machine). When ucast_solicit is greater than 0 it first tries to -send an ARP packet directly to the known host When that fails and -mcast_solicit is greater than 0, an ARP request is broadcasted. - -2.9 Appletalk -------------- - -The /proc/sys/net/appletalk directory holds the Appletalk configuration data -when Appletalk is loaded. The configurable parameters are: - -aarp-expiry-time ----------------- - -The amount of time we keep an ARP entry before expiring it. Used to age out -old hosts. - -aarp-resolve-time ------------------ - -The amount of time we will spend trying to resolve an Appletalk address. - -aarp-retransmit-limit ---------------------- - -The number of times we will retransmit a query before giving up. - -aarp-tick-time --------------- - -Controls the rate at which expires are checked. - -The directory /proc/net/appletalk holds the list of active Appletalk sockets -on a machine. - -The fields indicate the DDP type, the local address (in network:node format) -the remote address, the size of the transmit pending queue, the size of the -received queue (bytes waiting for applications to read) the state and the uid -owning the socket. - -/proc/net/atalk_iface lists all the interfaces configured for appletalk.It -shows the name of the interface, its Appletalk address, the network range on -that address (or network number for phase 1 networks), and the status of the -interface. - -/proc/net/atalk_route lists each known network route. It lists the target -(network) that the route leads to, the router (may be directly connected), the -route flags, and the device the route is using. - -2.10 IPX --------- - -The IPX protocol has no tunable values in proc/sys/net. - -The IPX protocol does, however, provide proc/net/ipx. This lists each IPX -socket giving the local and remote addresses in Novell format (that is -network:node:port). In accordance with the strange Novell tradition, -everything but the port is in hex. Not_Connected is displayed for sockets that -are not tied to a specific remote address. The Tx and Rx queue sizes indicate -the number of bytes pending for transmission and reception. The state -indicates the state the socket is in and the uid is the owning uid of the -socket. - -The /proc/net/ipx_interface file lists all IPX interfaces. For each interface -it gives the network number, the node number, and indicates if the network is -the primary network. It also indicates which device it is bound to (or -Internal for internal networks) and the Frame Type if appropriate. Linux -supports 802.3, 802.2, 802.2 SNAP and DIX (Blue Book) ethernet framing for -IPX. - -The /proc/net/ipx_route table holds a list of IPX routes. For each route it -gives the destination network, the router node (or Directly) and the network -address of the router (or Connected) for internal networks. - -2.11 /proc/sys/fs/mqueue - POSIX message queues filesystem ----------------------------------------------------------- - -The "mqueue" filesystem provides the necessary kernel features to enable the -creation of a user space library that implements the POSIX message queues -API (as noted by the MSG tag in the POSIX 1003.1-2001 version of the System -Interfaces specification.) - -The "mqueue" filesystem contains values for determining/setting the amount of -resources used by the file system. - -/proc/sys/fs/mqueue/queues_max is a read/write file for setting/getting the -maximum number of message queues allowed on the system. - -/proc/sys/fs/mqueue/msg_max is a read/write file for setting/getting the -maximum number of messages in a queue value. In fact it is the limiting value -for another (user) limit which is set in mq_open invocation. This attribute of -a queue must be less or equal then msg_max. - -/proc/sys/fs/mqueue/msgsize_max is a read/write file for setting/getting the -maximum message size value (it is every message queue's attribute set during -its creation). +------------------------------------------------------------------------------ +CHAPTER 3: PER-PROCESS PARAMETERS +------------------------------------------------------------------------------ -2.12 /proc/<pid>/oom_adj - Adjust the oom-killer score +3.1 /proc/<pid>/oom_adj - Adjust the oom-killer score ------------------------------------------------------ This file can be used to adjust the score used to select which processes @@ -2062,25 +1037,15 @@ The task with the highest badness score is then selected and its children are killed, process itself will be killed in an OOM situation when it does not have children or some of them disabled oom like described above. -2.13 /proc/<pid>/oom_score - Display current oom-killer score +3.2 /proc/<pid>/oom_score - Display current oom-killer score ------------------------------------------------------------- ------------------------------------------------------------------------------- This file can be used to check the current score used by the oom-killer is for any given <pid>. Use it together with /proc/<pid>/oom_adj to tune which process should be killed in an out-of-memory situation. ------------------------------------------------------------------------------- -Summary ------------------------------------------------------------------------------- -Certain aspects of kernel behavior can be modified at runtime, without the -need to recompile the kernel, or even to reboot the system. The files in the -/proc/sys tree can not only be read, but also modified. You can use the echo -command to write value into these files, thereby changing the default settings -of the kernel. ------------------------------------------------------------------------------- -2.14 /proc/<pid>/io - Display the IO accounting fields +3.3 /proc/<pid>/io - Display the IO accounting fields ------------------------------------------------------- This file contains IO statistics for each running process @@ -2182,7 +1147,7 @@ those 64-bit counters, process A could see an intermediate result. More information about this can be found within the taskstats documentation in Documentation/accounting. -2.15 /proc/<pid>/coredump_filter - Core dump filtering settings +3.4 /proc/<pid>/coredump_filter - Core dump filtering settings --------------------------------------------------------------- When a process is dumped, all anonymous memory is written to a core file as long as the size of the core file isn't limited. But sometimes we don't want @@ -2226,7 +1191,7 @@ For example: $ echo 0x7 > /proc/self/coredump_filter $ ./some_program -2.16 /proc/<pid>/mountinfo - Information about mounts +3.5 /proc/<pid>/mountinfo - Information about mounts -------------------------------------------------------- This file contains lines of the form: @@ -2263,30 +1228,3 @@ For more information on mount propagation see: Documentation/filesystems/sharedsubtree.txt -2.17 /proc/sys/fs/epoll - Configuration options for the epoll interface --------------------------------------------------------- - -This directory contains configuration options for the epoll(7) interface. - -max_user_instances ------------------- - -This is the maximum number of epoll file descriptors that a single user can -have open at a given time. The default value is 128, and should be enough -for normal users. - -max_user_watches ----------------- - -Every epoll file descriptor can store a number of files to be monitored -for event readiness. Each one of these monitored files constitutes a "watch". -This configuration option sets the maximum number of "watches" that are -allowed for each user. -Each "watch" costs roughly 90 bytes on a 32bit kernel, and roughly 160 bytes -on a 64bit one. -The current default value for max_user_watches is the 1/32 of the available -low memory, divided for the "watch" cost in bytes. - - ------------------------------------------------------------------------------- - diff --git a/Documentation/filesystems/sysfs-pci.txt b/Documentation/filesystems/sysfs-pci.txt index 9f8740ca3f3..26e4b8bc53e 100644 --- a/Documentation/filesystems/sysfs-pci.txt +++ b/Documentation/filesystems/sysfs-pci.txt @@ -12,6 +12,7 @@ that support it. For example, a given bus might look like this: | |-- enable | |-- irq | |-- local_cpus + | |-- remove | |-- resource | |-- resource0 | |-- resource1 @@ -36,6 +37,7 @@ files, each with their own function. enable Whether the device is enabled (ascii, rw) irq IRQ number (ascii, ro) local_cpus nearby CPU mask (cpumask, ro) + remove remove device from kernel's list (ascii, wo) resource PCI resource host addresses (ascii, ro) resource0..N PCI resource N, if present (binary, mmap) resource0_wc..N_wc PCI WC map resource N, if prefetchable (binary, mmap) @@ -46,6 +48,7 @@ files, each with their own function. ro - read only file rw - file is readable and writable + wo - write only file mmap - file is mmapable ascii - file contains ascii text binary - file contains binary data @@ -73,6 +76,13 @@ that the device must be enabled for a rom read to return data succesfully. In the event a driver is not bound to the device, it can be enabled using the 'enable' file, documented above. +The 'remove' file is used to remove the PCI device, by writing a non-zero +integer to the file. This does not involve any kind of hot-plug functionality, +e.g. powering off the device. The device is removed from the kernel's list of +PCI devices, the sysfs directory for it is removed, and the device will be +removed from any drivers attached to it. Removal of PCI root buses is +disallowed. + Accessing legacy resources through sysfs ---------------------------------------- diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt index b1b98870124..145c25a170c 100644 --- a/Documentation/gpio.txt +++ b/Documentation/gpio.txt @@ -123,7 +123,10 @@ platform-specific implementation issue. Using GPIOs ----------- -One of the first things to do with a GPIO, often in board setup code when +The first thing a system should do with a GPIO is allocate it, using +the gpio_request() call; see later. + +One of the next things to do with a GPIO, often in board setup code when setting up a platform_device using the GPIO, is mark its direction: /* set as input or output, returning 0 or negative errno */ @@ -141,8 +144,8 @@ This helps avoid signal glitching during system startup. For compatibility with legacy interfaces to GPIOs, setting the direction of a GPIO implicitly requests that GPIO (see below) if it has not been -requested already. That compatibility may be removed in the future; -explicitly requesting GPIOs is strongly preferred. +requested already. That compatibility is being removed from the optional +gpiolib framework. Setting the direction can fail if the GPIO number is invalid, or when that particular GPIO can't be used in that mode. It's generally a bad @@ -195,7 +198,7 @@ This requires sleeping, which can't be done from inside IRQ handlers. Platforms that support this type of GPIO distinguish them from other GPIOs by returning nonzero from this call (which requires a valid GPIO number, -either explicitly or implicitly requested): +which should have been previously allocated with gpio_request): int gpio_cansleep(unsigned gpio); @@ -212,10 +215,9 @@ for GPIOs that can't be accessed from IRQ handlers, these calls act the same as the spinlock-safe calls. -Claiming and Releasing GPIOs (OPTIONAL) ---------------------------------------- +Claiming and Releasing GPIOs +---------------------------- To help catch system configuration errors, two calls are defined. -However, many platforms don't currently support this mechanism. /* request GPIO, returning 0 or negative errno. * non-null labels may be useful for diagnostics. @@ -244,13 +246,6 @@ Some platforms may also use knowledge about what GPIOs are active for power management, such as by powering down unused chip sectors and, more easily, gating off unused clocks. -These two calls are optional because not not all current Linux platforms -offer such functionality in their GPIO support; a valid implementation -could return success for all gpio_request() calls. Unlike the other calls, -the state they represent doesn't normally match anything from a hardware -register; it's just a software bitmap which clearly is not necessary for -correct operation of hardware or (bug free) drivers. - Note that requesting a GPIO does NOT cause it to be configured in any way; it just marks that GPIO as in use. Separate code must handle any pin setup (e.g. controlling which pin the GPIO uses, pullup/pulldown). diff --git a/Documentation/hwmon/ds1621 b/Documentation/hwmon/ds1621 index 1fee6f1e6bc..5e97f333c4d 100644 --- a/Documentation/hwmon/ds1621 +++ b/Documentation/hwmon/ds1621 @@ -49,12 +49,9 @@ of up to +/- 0.5 degrees even when compared against precise temperature readings. Be sure to have a high vs. low temperature limit gap of al least 1.0 degree Celsius to avoid Tout "bouncing", though! -As for alarms, you can read the alarm status of the DS1621 via the 'alarms' -/sys file interface. The result consists mainly of bit 6 and 5 of the -configuration register of the chip; bit 6 (0x40 or 64) is the high alarm -bit and bit 5 (0x20 or 32) the low one. These bits are set when the high or -low limits are met or exceeded and are reset by the module as soon as the -respective temperature ranges are left. +The alarm bits are set when the high or low limits are met or exceeded and +are reset by the module as soon as the respective temperature ranges are +left. The alarm registers are in no way suitable to find out about the actual status of Tout. They will only tell you about its history, whether or not @@ -64,45 +61,3 @@ with neither of the alarms set. Temperature conversion of the DS1621 takes up to 1000ms; internal access to non-volatile registers may last for 10ms or below. - -High Accuracy Temperature Reading ---------------------------------- - -As said before, the temperature issued via the 9-bit i2c-bus data is -somewhat arbitrary. Internally, the temperature conversion is of a -different kind that is explained (not so...) well in the DS1621 data sheet. -To cut the long story short: Inside the DS1621 there are two oscillators, -both of them biassed by a temperature coefficient. - -Higher resolution of the temperature reading can be achieved using the -internal projection, which means taking account of REG_COUNT and REG_SLOPE -(the driver manages them): - -Taken from Dallas Semiconductors App Note 068: 'Increasing Temperature -Resolution on the DS1620' and App Note 105: 'High Resolution Temperature -Measurement with Dallas Direct-to-Digital Temperature Sensors' - -- Read the 9-bit temperature and strip the LSB (Truncate the .5 degs) -- The resulting value is TEMP_READ. -- Then, read REG_COUNT. -- And then, REG_SLOPE. - - TEMP = TEMP_READ - 0.25 + ((REG_SLOPE - REG_COUNT) / REG_SLOPE) - -Note that this is what the DONE bit in the DS1621 configuration register is -good for: Internally, one temperature conversion takes up to 1000ms. Before -that conversion is complete you will not be able to read valid things out -of REG_COUNT and REG_SLOPE. The DONE bit, as you may have guessed by now, -tells you whether the conversion is complete ("done", in plain English) and -thus, whether the values you read are good or not. - -The DS1621 has two modes of operation: "Continuous" conversion, which can -be understood as the default stand-alone mode where the chip gets the -temperature and controls external devices via its Tout pin or tells other -i2c's about it if they care. The other mode is called "1SHOT", that means -that it only figures out about the temperature when it is explicitly told -to do so; this can be seen as power saving mode. - -Now if you want to read REG_COUNT and REG_SLOPE, you have to either stop -the continuous conversions until the contents of these registers are valid, -or, in 1SHOT mode, you have to have one conversion made. diff --git a/Documentation/hwmon/lis3lv02d b/Documentation/hwmon/lis3lv02d index 287f8c90265..effe949a728 100644 --- a/Documentation/hwmon/lis3lv02d +++ b/Documentation/hwmon/lis3lv02d @@ -1,11 +1,11 @@ Kernel driver lis3lv02d -================== +======================= Supported chips: * STMicroelectronics LIS3LV02DL and LIS3LV02DQ -Author: +Authors: Yan Burman <burman.yan@gmail.com> Eric Piel <eric.piel@tremplin-utc.net> @@ -15,7 +15,7 @@ Description This driver provides support for the accelerometer found in various HP laptops sporting the feature officially called "HP Mobile Data -Protection System 3D" or "HP 3D DriveGuard". It detect automatically +Protection System 3D" or "HP 3D DriveGuard". It detects automatically laptops with this sensor. Known models (for now the HP 2133, nc6420, nc2510, nc8510, nc84x0, nw9440 and nx9420) will have their axis automatically oriented on standard way (eg: you can directly play @@ -27,7 +27,7 @@ position - 3D position that the accelerometer reports. Format: "(x,y,z)" calibrate - read: values (x, y, z) that are used as the base for input class device operation. write: forces the base to be recalibrated with the current - position. + position. rate - reports the sampling rate of the accelerometer device in HZ This driver also provides an absolute input class device, allowing @@ -48,7 +48,7 @@ For better compatibility between the various laptops. The values reported by the accelerometer are converted into a "standard" organisation of the axes (aka "can play neverball out of the box"): * When the laptop is horizontal the position reported is about 0 for X and Y -and a positive value for Z + and a positive value for Z * If the left side is elevated, X increases (becomes positive) * If the front side (where the touchpad is) is elevated, Y decreases (becomes negative) @@ -59,3 +59,13 @@ email to the authors to add it to the database. When reporting a new laptop, please include the output of "dmidecode" plus the value of /sys/devices/platform/lis3lv02d/position in these four cases. +Q&A +--- + +Q: How do I safely simulate freefall? I have an HP "portable +workstation" which has about 3.5kg and a plastic case, so letting it +fall to the ground is out of question... + +A: The sensor is pretty sensitive, so your hands can do it. Lift it +into free space, follow the fall with your hands for like 10 +centimeters. That should be enough to trigger the detection. diff --git a/Documentation/hwmon/ltc4215 b/Documentation/hwmon/ltc4215 new file mode 100644 index 00000000000..2e6a21eb656 --- /dev/null +++ b/Documentation/hwmon/ltc4215 @@ -0,0 +1,50 @@ +Kernel driver ltc4215 +===================== + +Supported chips: + * Linear Technology LTC4215 + Prefix: 'ltc4215' + Addresses scanned: 0x44 + Datasheet: + http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1163,P17572,D12697 + +Author: Ira W. Snyder <iws@ovro.caltech.edu> + + +Description +----------- + +The LTC4215 controller allows a board to be safely inserted and removed +from a live backplane. + + +Usage Notes +----------- + +This driver does not probe for LTC4215 devices, due to the fact that some +of the possible addresses are unfriendly to probing. You will need to use +the "force" parameter to tell the driver where to find the device. + +Example: the following will load the driver for an LTC4215 at address 0x44 +on I2C bus #0: +$ modprobe ltc4215 force=0,0x44 + + +Sysfs entries +------------- + +The LTC4215 has built-in limits for overvoltage, undervoltage, and +undercurrent warnings. This makes it very likely that the reference +circuit will be used. + +in1_input input voltage +in2_input output voltage + +in1_min_alarm input undervoltage alarm +in1_max_alarm input overvoltage alarm + +curr1_input current +curr1_max_alarm overcurrent alarm + +power1_input power usage +power1_alarm power bad alarm diff --git a/Documentation/i2c/chips/pcf8591 b/Documentation/hwmon/pcf8591 index 5628fcf4207..5628fcf4207 100644 --- a/Documentation/i2c/chips/pcf8591 +++ b/Documentation/hwmon/pcf8591 diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index 6dbfd5efd99..2f10ce6a879 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -365,6 +365,7 @@ energy[1-*]_input Cumulative energy use Unit: microJoule RO + ********** * Alarms * ********** @@ -453,6 +454,27 @@ beep_mask Bitmask for beep. RW +*********************** +* Intrusion detection * +*********************** + +intrusion[0-*]_alarm + Chassis intrusion detection + 0: OK + 1: intrusion detected + RW + Contrary to regular alarm flags which clear themselves + automatically when read, this one sticks until cleared by + the user. This is done by writing 0 to the file. Writing + other values is unsupported. + +intrusion[0-*]_beep + Chassis intrusion beep + 0: disable + 1: enable + RW + + sysfs attribute writes interpretation ------------------------------------- diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf index d6e1ae30fa6..b6eb59384bb 100644 --- a/Documentation/hwmon/w83627ehf +++ b/Documentation/hwmon/w83627ehf @@ -2,30 +2,40 @@ Kernel driver w83627ehf ======================= Supported chips: - * Winbond W83627EHF/EHG/DHG (ISA access ONLY) + * Winbond W83627EHF/EHG (ISA access ONLY) Prefix: 'w83627ehf' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: - http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83627EHF_%20W83627EHGb.pdf - DHG datasheet confidential. + http://www.nuvoton.com.tw/NR/rdonlyres/A6A258F0-F0C9-4F97-81C0-C4D29E7E943E/0/W83627EHF.pdf + * Winbond W83627DHG + Prefix: 'w83627dhg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: + http://www.nuvoton.com.tw/NR/rdonlyres/7885623D-A487-4CF9-A47F-30C5F73D6FE6/0/W83627DHG.pdf + * Winbond W83667HG + Prefix: 'w83667hg' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: not available Authors: Jean Delvare <khali@linux-fr.org> Yuan Mu (Winbond) Rudolf Marek <r.marek@assembler.cz> David Hubbard <david.c.hubbard@gmail.com> + Gong Jun <JGong@nuvoton.com> Description ----------- -This driver implements support for the Winbond W83627EHF, W83627EHG, and -W83627DHG super I/O chips. We will refer to them collectively as Winbond chips. +This driver implements support for the Winbond W83627EHF, W83627EHG, +W83627DHG and W83667HG super I/O chips. We will refer to them collectively +as Winbond chips. The chips implement three temperature sensors, five fan rotation speed sensors, ten analog voltage sensors (only nine for the 627DHG), one -VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG), alarms with beep -warnings (control unimplemented), and some automatic fan regulation -strategies (plus manual fan control mode). +VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG and 667HG), alarms +with beep warnings (control unimplemented), and some automatic fan +regulation strategies (plus manual fan control mode). Temperatures are measured in degrees Celsius and measurement resolution is 1 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when @@ -54,7 +64,8 @@ follows: temp1 -> pwm1 temp2 -> pwm2 temp3 -> pwm3 -prog -> pwm4 (the programmable setting is not supported by the driver) +prog -> pwm4 (not on 667HG; the programmable setting is not supported by + the driver) /sys files ---------- diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt index f1d63990332..1f779a25c70 100644 --- a/Documentation/ioctl/ioctl-number.txt +++ b/Documentation/ioctl/ioctl-number.txt @@ -122,10 +122,8 @@ Code Seq# Include File Comments 'c' 00-7F linux/coda.h conflict! 'c' 80-9F arch/s390/include/asm/chsc.h 'd' 00-FF linux/char/drm/drm/h conflict! -'d' 00-DF linux/video_decoder.h conflict! 'd' F0-FF linux/digi1.h 'e' all linux/digi1.h conflict! -'e' 00-1F linux/video_encoder.h conflict! 'e' 00-1F net/irda/irtty.h conflict! 'f' 00-1F linux/ext2_fs.h 'h' 00-7F Charon filesystem diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index d1e2fcb6298..240257dd423 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -492,6 +492,16 @@ and is between 256 and 4096 characters. It is defined in the file Range: 0 - 8192 Default: 64 + dma_debug=off If the kernel is compiled with DMA_API_DEBUG support + this option disables the debugging code at boot. + + dma_debug_entries=<number> + This option allows to tune the number of preallocated + entries for DMA-API debugging code. One entry is + required per DMA-API allocation. Use this if the + DMA-API debugging code disables itself because the + architectural default is too low. + hpet= [X86-32,HPET] option to control HPET usage Format: { enable (default) | disable | force | verbose } @@ -1685,6 +1695,8 @@ and is between 256 and 4096 characters. It is defined in the file See also Documentation/blockdev/paride.txt. pci=option[,option...] [PCI] various PCI subsystem options: + earlydump [X86] dump PCI config space before the kernel + changes anything off [X86] don't probe for the PCI bus bios [X86-32] force use of PCI BIOS, don't access the hardware directly. Use this if your machine @@ -1784,6 +1796,15 @@ and is between 256 and 4096 characters. It is defined in the file cbmemsize=nn[KMG] The fixed amount of bus space which is reserved for the CardBus bridge's memory window. The default value is 64 megabytes. + resource_alignment= + Format: + [<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...] + Specifies alignment and device to reassign + aligned memory resources. + If <order of align> is not specified, + PAGE_SIZE is used as alignment. + PCI-PCI bridge can be specified, if resource + windows need to be expanded. pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power Management. @@ -2030,15 +2051,6 @@ and is between 256 and 4096 characters. It is defined in the file If enabled at boot time, /selinux/disable can be used later to disable prior to initial policy load. - selinux_compat_net = - [SELINUX] Set initial selinux_compat_net flag value. - Format: { "0" | "1" } - 0 -- use new secmark-based packet controls - 1 -- use legacy packet controls - Default value is 0 (preferred). - Value can be changed at runtime via - /selinux/compat_net. - serialnumber [BUGS=X86-32] shapers= [NET] diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c index f2dbbf3bdea..d36fcc0f271 100644 --- a/Documentation/lguest/lguest.c +++ b/Documentation/lguest/lguest.c @@ -1630,6 +1630,13 @@ static bool service_io(struct device *dev) } } + /* OK, so we noted that it was pretty poor to use an fdatasync as a + * barrier. But Christoph Hellwig points out that we need a sync + * *afterwards* as well: "Barriers specify no reordering to the front + * or the back." And Jens Axboe confirmed it, so here we are: */ + if (out->type & VIRTIO_BLK_T_BARRIER) + fdatasync(vblk->fd); + /* We can't trigger an IRQ, because we're not the Launcher. It does * that when we tell it we're done. */ add_used(dev->vq, head, wlen); diff --git a/Documentation/lockdep-design.txt b/Documentation/lockdep-design.txt index 48877301815..938ea22f2cc 100644 --- a/Documentation/lockdep-design.txt +++ b/Documentation/lockdep-design.txt @@ -27,33 +27,37 @@ lock-class. State ----- -The validator tracks lock-class usage history into 5 separate state bits: +The validator tracks lock-class usage history into 4n + 1 separate state bits: -- 'ever held in hardirq context' [ == hardirq-safe ] -- 'ever held in softirq context' [ == softirq-safe ] -- 'ever held with hardirqs enabled' [ == hardirq-unsafe ] -- 'ever held with softirqs and hardirqs enabled' [ == softirq-unsafe ] +- 'ever held in STATE context' +- 'ever head as readlock in STATE context' +- 'ever head with STATE enabled' +- 'ever head as readlock with STATE enabled' + +Where STATE can be either one of (kernel/lockdep_states.h) + - hardirq + - softirq + - reclaim_fs - 'ever used' [ == !unused ] -When locking rules are violated, these 4 state bits are presented in the -locking error messages, inside curlies. A contrived example: +When locking rules are violated, these state bits are presented in the +locking error messages, inside curlies. A contrived example: modprobe/2287 is trying to acquire lock: - (&sio_locks[i].lock){--..}, at: [<c02867fd>] mutex_lock+0x21/0x24 + (&sio_locks[i].lock){-.-...}, at: [<c02867fd>] mutex_lock+0x21/0x24 but task is already holding lock: - (&sio_locks[i].lock){--..}, at: [<c02867fd>] mutex_lock+0x21/0x24 + (&sio_locks[i].lock){-.-...}, at: [<c02867fd>] mutex_lock+0x21/0x24 -The bit position indicates hardirq, softirq, hardirq-read, -softirq-read respectively, and the character displayed in each -indicates: +The bit position indicates STATE, STATE-read, for each of the states listed +above, and the character displayed in each indicates: '.' acquired while irqs disabled '+' acquired in irq context '-' acquired with irqs enabled - '?' read acquired in irq context with irqs enabled. + '?' acquired in irq context with irqs enabled. Unused mutexes cannot be part of the cause of an error. diff --git a/Documentation/misc-devices/isl29003 b/Documentation/misc-devices/isl29003 new file mode 100644 index 00000000000..c4ff5f38e01 --- /dev/null +++ b/Documentation/misc-devices/isl29003 @@ -0,0 +1,62 @@ +Kernel driver isl29003 +===================== + +Supported chips: +* Intersil ISL29003 +Prefix: 'isl29003' +Addresses scanned: none +Datasheet: +http://www.intersil.com/data/fn/fn7464.pdf + +Author: Daniel Mack <daniel@caiaq.de> + + +Description +----------- +The ISL29003 is an integrated light sensor with a 16-bit integrating type +ADC, I2C user programmable lux range select for optimized counts/lux, and +I2C multi-function control and monitoring capabilities. The internal ADC +provides 16-bit resolution while rejecting 50Hz and 60Hz flicker caused by +artificial light sources. + +The driver allows to set the lux range, the bit resolution, the operational +mode (see below) and the power state of device and can read the current lux +value, of course. + + +Detection +--------- + +The ISL29003 does not have an ID register which could be used to identify +it, so the detection routine will just try to read from the configured I2C +addess and consider the device to be present as soon as it ACKs the +transfer. + + +Sysfs entries +------------- + +range: + 0: 0 lux to 1000 lux (default) + 1: 0 lux to 4000 lux + 2: 0 lux to 16,000 lux + 3: 0 lux to 64,000 lux + +resolution: + 0: 2^16 cycles (default) + 1: 2^12 cycles + 2: 2^8 cycles + 3: 2^4 cycles + +mode: + 0: diode1's current (unsigned 16bit) (default) + 1: diode1's current (unsigned 16bit) + 2: difference between diodes (l1 - l2, signed 15bit) + +power_state: + 0: device is disabled (default) + 1: device is enabled + +lux (read only): + returns the value from the last sensor reading + diff --git a/Documentation/powerpc/dts-bindings/fsl/dma.txt b/Documentation/powerpc/dts-bindings/fsl/dma.txt index cc453110fc4..0732cdd05ba 100644 --- a/Documentation/powerpc/dts-bindings/fsl/dma.txt +++ b/Documentation/powerpc/dts-bindings/fsl/dma.txt @@ -35,30 +35,30 @@ Example: #address-cells = <1>; #size-cells = <1>; compatible = "fsl,mpc8349-dma", "fsl,elo-dma"; - reg = <82a8 4>; - ranges = <0 8100 1a4>; + reg = <0x82a8 4>; + ranges = <0 0x8100 0x1a4>; interrupt-parent = <&ipic>; - interrupts = <47 8>; + interrupts = <71 8>; cell-index = <0>; dma-channel@0 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <0>; - reg = <0 80>; + reg = <0 0x80>; }; dma-channel@80 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <1>; - reg = <80 80>; + reg = <0x80 0x80>; }; dma-channel@100 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <2>; - reg = <100 80>; + reg = <0x100 0x80>; }; dma-channel@180 { compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; cell-index = <3>; - reg = <180 80>; + reg = <0x180 0x80>; }; }; @@ -93,36 +93,36 @@ Example: #address-cells = <1>; #size-cells = <1>; compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma"; - reg = <21300 4>; - ranges = <0 21100 200>; + reg = <0x21300 4>; + ranges = <0 0x21100 0x200>; cell-index = <0>; dma-channel@0 { compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0 80>; + reg = <0 0x80>; cell-index = <0>; interrupt-parent = <&mpic>; - interrupts = <14 2>; + interrupts = <20 2>; }; dma-channel@80 { compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <80 80>; + reg = <0x80 0x80>; cell-index = <1>; interrupt-parent = <&mpic>; - interrupts = <15 2>; + interrupts = <21 2>; }; dma-channel@100 { compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <100 80>; + reg = <0x100 0x80>; cell-index = <2>; interrupt-parent = <&mpic>; - interrupts = <16 2>; + interrupts = <22 2>; }; dma-channel@180 { compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <180 80>; + reg = <0x180 0x80>; cell-index = <3>; interrupt-parent = <&mpic>; - interrupts = <17 2>; + interrupts = <23 2>; }; }; diff --git a/Documentation/powerpc/dts-bindings/fsl/esdhc.txt b/Documentation/powerpc/dts-bindings/fsl/esdhc.txt new file mode 100644 index 00000000000..60084655776 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/fsl/esdhc.txt @@ -0,0 +1,24 @@ +* Freescale Enhanced Secure Digital Host Controller (eSDHC) + +The Enhanced Secure Digital Host Controller provides an interface +for MMC, SD, and SDIO types of memory cards. + +Required properties: + - compatible : should be + "fsl,<chip>-esdhc", "fsl,mpc8379-esdhc" for MPC83xx processors. + "fsl,<chip>-esdhc", "fsl,mpc8536-esdhc" for MPC85xx processors. + - reg : should contain eSDHC registers location and length. + - interrupts : should contain eSDHC interrupt. + - interrupt-parent : interrupt source phandle. + - clock-frequency : specifies eSDHC base clock frequency. + +Example: + +sdhci@2e000 { + compatible = "fsl,mpc8378-esdhc", "fsl,mpc8379-esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <42 0x8>; + interrupt-parent = <&ipic>; + /* Filled in by U-Boot */ + clock-frequency = <0>; +}; diff --git a/Documentation/powerpc/dts-bindings/fsl/ssi.txt b/Documentation/powerpc/dts-bindings/fsl/ssi.txt index a2d963998a6..5ff76c9c57d 100644 --- a/Documentation/powerpc/dts-bindings/fsl/ssi.txt +++ b/Documentation/powerpc/dts-bindings/fsl/ssi.txt @@ -4,44 +4,56 @@ The SSI is a serial device that communicates with audio codecs. It can be programmed in AC97, I2S, left-justified, or right-justified modes. Required properties: -- compatible : compatible list, containing "fsl,ssi" -- cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on -- reg : offset and length of the register set for the device -- interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and - level information for the interrupt. This should be - encoded based on the information in section 2) - depending on the type of interrupt controller you - have. -- interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. -- fsl,mode : the operating mode for the SSI interface - "i2s-slave" - I2S mode, SSI is clock slave - "i2s-master" - I2S mode, SSI is clock master - "lj-slave" - left-justified mode, SSI is clock slave - "lj-master" - l.j. mode, SSI is clock master - "rj-slave" - right-justified mode, SSI is clock slave - "rj-master" - r.j., SSI is clock master - "ac97-slave" - AC97 mode, SSI is clock slave - "ac97-master" - AC97 mode, SSI is clock master -- fsl,playback-dma: phandle to a node for the DMA channel to use for +- compatible: Compatible list, contains "fsl,ssi". +- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. +- reg: Offset and length of the register set for the device. +- interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and + level information for the interrupt. This should be + encoded based on the information in section 2) + depending on the type of interrupt controller you + have. +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this device. +- fsl,mode: The operating mode for the SSI interface. + "i2s-slave" - I2S mode, SSI is clock slave + "i2s-master" - I2S mode, SSI is clock master + "lj-slave" - left-justified mode, SSI is clock slave + "lj-master" - l.j. mode, SSI is clock master + "rj-slave" - right-justified mode, SSI is clock slave + "rj-master" - r.j., SSI is clock master + "ac97-slave" - AC97 mode, SSI is clock slave + "ac97-master" - AC97 mode, SSI is clock master +- fsl,playback-dma: Phandle to a node for the DMA channel to use for playback of audio. This is typically dictated by SOC design. See the notes below. -- fsl,capture-dma: phandle to a node for the DMA channel to use for +- fsl,capture-dma: Phandle to a node for the DMA channel to use for capture (recording) of audio. This is typically dictated by SOC design. See the notes below. +- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. + This number is the maximum allowed value for SFCSR[TFWM0]. +- fsl,ssi-asynchronous: + If specified, the SSI is to be programmed in asynchronous + mode. In this mode, pins SRCK, STCK, SRFS, and STFS must + all be connected to valid signals. In synchronous mode, + SRCK and SRFS are ignored. Asynchronous mode allows + playback and capture to use different sample sizes and + sample rates. Some drivers may require that SRCK and STCK + be connected together, and SRFS and STFS be connected + together. This would still allow different sample sizes, + but not different sample rates. Optional properties: -- codec-handle : phandle to a 'codec' node that defines an audio - codec connected to this SSI. This node is typically - a child of an I2C or other control node. +- codec-handle: Phandle to a 'codec' node that defines an audio + codec connected to this SSI. This node is typically + a child of an I2C or other control node. Child 'codec' node required properties: -- compatible : compatible list, contains the name of the codec +- compatible: Compatible list, contains the name of the codec Child 'codec' node optional properties: -- clock-frequency : The frequency of the input clock, which typically - comes from an on-board dedicated oscillator. +- clock-frequency: The frequency of the input clock, which typically comes + from an on-board dedicated oscillator. Notes on fsl,playback-dma and fsl,capture-dma: diff --git a/Documentation/powerpc/dts-bindings/mmc-spi-slot.txt b/Documentation/powerpc/dts-bindings/mmc-spi-slot.txt new file mode 100644 index 00000000000..c39ac289195 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/mmc-spi-slot.txt @@ -0,0 +1,23 @@ +MMC/SD/SDIO slot directly connected to a SPI bus + +Required properties: +- compatible : should be "mmc-spi-slot". +- reg : should specify SPI address (chip-select number). +- spi-max-frequency : maximum frequency for this device (Hz). +- voltage-ranges : two cells are required, first cell specifies minimum + slot voltage (mV), second cell specifies maximum slot voltage (mV). + Several ranges could be specified. +- gpios : (optional) may specify GPIOs in this order: Card-Detect GPIO, + Write-Protect GPIO. + +Example: + + mmc-slot@0 { + compatible = "fsl,mpc8323rdb-mmc-slot", + "mmc-spi-slot"; + reg = <0>; + gpios = <&qe_pio_d 14 1 + &qe_pio_d 15 0>; + voltage-ranges = <3300 3300>; + spi-max-frequency = <50000000>; + }; diff --git a/Documentation/sysctl/00-INDEX b/Documentation/sysctl/00-INDEX index a20a9066dc4..1286f455992 100644 --- a/Documentation/sysctl/00-INDEX +++ b/Documentation/sysctl/00-INDEX @@ -10,6 +10,8 @@ fs.txt - documentation for /proc/sys/fs/*. kernel.txt - documentation for /proc/sys/kernel/*. +net.txt + - documentation for /proc/sys/net/*. sunrpc.txt - documentation for /proc/sys/sunrpc/*. vm.txt diff --git a/Documentation/sysctl/fs.txt b/Documentation/sysctl/fs.txt index f99254327ae..1458448436c 100644 --- a/Documentation/sysctl/fs.txt +++ b/Documentation/sysctl/fs.txt @@ -1,5 +1,6 @@ Documentation for /proc/sys/fs/* kernel version 2.2.10 (c) 1998, 1999, Rik van Riel <riel@nl.linux.org> + (c) 2009, Shen Feng<shen@cn.fujitsu.com> For general info and legal blurb, please look in README. @@ -14,7 +15,12 @@ kernel. Since some of the files _can_ be used to screw up your system, it is advisable to read both documentation and source before actually making adjustments. +1. /proc/sys/fs +---------------------------------------------------------- + Currently, these files are in /proc/sys/fs: +- aio-max-nr +- aio-nr - dentry-state - dquot-max - dquot-nr @@ -30,8 +36,15 @@ Currently, these files are in /proc/sys/fs: - super-max - super-nr -Documentation for the files in /proc/sys/fs/binfmt_misc is -in Documentation/binfmt_misc.txt. +============================================================== + +aio-nr & aio-max-nr: + +aio-nr is the running total of the number of events specified on the +io_setup system call for all currently active aio contexts. If aio-nr +reaches aio-max-nr then io_setup will fail with EAGAIN. Note that +raising aio-max-nr does not result in the pre-allocation or re-sizing +of any kernel data structures. ============================================================== @@ -178,3 +191,60 @@ requests. aio-max-nr allows you to change the maximum value aio-nr can grow to. ============================================================== + + +2. /proc/sys/fs/binfmt_misc +---------------------------------------------------------- + +Documentation for the files in /proc/sys/fs/binfmt_misc is +in Documentation/binfmt_misc.txt. + + +3. /proc/sys/fs/mqueue - POSIX message queues filesystem +---------------------------------------------------------- + +The "mqueue" filesystem provides the necessary kernel features to enable the +creation of a user space library that implements the POSIX message queues +API (as noted by the MSG tag in the POSIX 1003.1-2001 version of the System +Interfaces specification.) + +The "mqueue" filesystem contains values for determining/setting the amount of +resources used by the file system. + +/proc/sys/fs/mqueue/queues_max is a read/write file for setting/getting the +maximum number of message queues allowed on the system. + +/proc/sys/fs/mqueue/msg_max is a read/write file for setting/getting the +maximum number of messages in a queue value. In fact it is the limiting value +for another (user) limit which is set in mq_open invocation. This attribute of +a queue must be less or equal then msg_max. + +/proc/sys/fs/mqueue/msgsize_max is a read/write file for setting/getting the +maximum message size value (it is every message queue's attribute set during +its creation). + + +4. /proc/sys/fs/epoll - Configuration options for the epoll interface +-------------------------------------------------------- + +This directory contains configuration options for the epoll(7) interface. + +max_user_instances +------------------ + +This is the maximum number of epoll file descriptors that a single user can +have open at a given time. The default value is 128, and should be enough +for normal users. + +max_user_watches +---------------- + +Every epoll file descriptor can store a number of files to be monitored +for event readiness. Each one of these monitored files constitutes a "watch". +This configuration option sets the maximum number of "watches" that are +allowed for each user. +Each "watch" costs roughly 90 bytes on a 32bit kernel, and roughly 160 bytes +on a 64bit one. +The current default value for max_user_watches is the 1/32 of the available +low memory, divided for the "watch" cost in bytes. + diff --git a/Documentation/sysctl/kernel.txt b/Documentation/sysctl/kernel.txt index a4ccdd1981c..f11ca7979fa 100644 --- a/Documentation/sysctl/kernel.txt +++ b/Documentation/sysctl/kernel.txt @@ -1,5 +1,6 @@ Documentation for /proc/sys/kernel/* kernel version 2.2.10 (c) 1998, 1999, Rik van Riel <riel@nl.linux.org> + (c) 2009, Shen Feng<shen@cn.fujitsu.com> For general info and legal blurb, please look in README. @@ -18,6 +19,7 @@ Currently, these files might (depending on your configuration) show up in /proc/sys/kernel: - acpi_video_flags - acct +- auto_msgmni - core_pattern - core_uses_pid - ctrl-alt-del @@ -33,6 +35,7 @@ show up in /proc/sys/kernel: - msgmax - msgmnb - msgmni +- nmi_watchdog - osrelease - ostype - overflowgid @@ -40,6 +43,7 @@ show up in /proc/sys/kernel: - panic - pid_max - powersave-nap [ PPC only ] +- panic_on_unrecovered_nmi - printk - randomize_va_space - real-root-dev ==> Documentation/initrd.txt @@ -55,6 +59,7 @@ show up in /proc/sys/kernel: - sysrq ==> Documentation/sysrq.txt - tainted - threads-max +- unknown_nmi_panic - version ============================================================== @@ -381,3 +386,51 @@ can be ORed together: 512 - A kernel warning has occurred. 1024 - A module from drivers/staging was loaded. +============================================================== + +auto_msgmni: + +Enables/Disables automatic recomputing of msgmni upon memory add/remove or +upon ipc namespace creation/removal (see the msgmni description above). +Echoing "1" into this file enables msgmni automatic recomputing. +Echoing "0" turns it off. +auto_msgmni default value is 1. + +============================================================== + +nmi_watchdog: + +Enables/Disables the NMI watchdog on x86 systems. When the value is non-zero +the NMI watchdog is enabled and will continuously test all online cpus to +determine whether or not they are still functioning properly. Currently, +passing "nmi_watchdog=" parameter at boot time is required for this function +to work. + +If LAPIC NMI watchdog method is in use (nmi_watchdog=2 kernel parameter), the +NMI watchdog shares registers with oprofile. By disabling the NMI watchdog, +oprofile may have more registers to utilize. + +============================================================== + +unknown_nmi_panic: + +The value in this file affects behavior of handling NMI. When the value is +non-zero, unknown NMI is trapped and then panic occurs. At that time, kernel +debugging information is displayed on console. + +NMI switch that most IA32 servers have fires unknown NMI up, for example. +If a system hangs up, try pressing the NMI switch. + +============================================================== + +panic_on_unrecovered_nmi: + +The default Linux behaviour on an NMI of either memory or unknown is to continue +operation. For many environments such as scientific computing it is preferable +that the box is taken out and the error dealt with than an uncorrected +parity/ECC error get propogated. + +A small number of systems do generate NMI's for bizarre random reasons such as +power management so the default is off. That sysctl works like the existing +panic controls already in that directory. + diff --git a/Documentation/sysctl/net.txt b/Documentation/sysctl/net.txt new file mode 100644 index 00000000000..a34d55b6544 --- /dev/null +++ b/Documentation/sysctl/net.txt @@ -0,0 +1,175 @@ +Documentation for /proc/sys/net/* kernel version 2.4.0-test11-pre4 + (c) 1999 Terrehon Bowden <terrehon@pacbell.net> + Bodo Bauer <bb@ricochet.net> + (c) 2000 Jorge Nerin <comandante@zaralinux.com> + (c) 2009 Shen Feng <shen@cn.fujitsu.com> + +For general info and legal blurb, please look in README. + +============================================================== + +This file contains the documentation for the sysctl files in +/proc/sys/net and is valid for Linux kernel version 2.4.0-test11-pre4. + +The interface to the networking parts of the kernel is located in +/proc/sys/net. The following table shows all possible subdirectories.You may +see only some of them, depending on your kernel's configuration. + + +Table : Subdirectories in /proc/sys/net +.............................................................................. + Directory Content Directory Content + core General parameter appletalk Appletalk protocol + unix Unix domain sockets netrom NET/ROM + 802 E802 protocol ax25 AX25 + ethernet Ethernet protocol rose X.25 PLP layer + ipv4 IP version 4 x25 X.25 protocol + ipx IPX token-ring IBM token ring + bridge Bridging decnet DEC net + ipv6 IP version 6 +.............................................................................. + +1. /proc/sys/net/core - Network core options +------------------------------------------------------- + +rmem_default +------------ + +The default setting of the socket receive buffer in bytes. + +rmem_max +-------- + +The maximum receive socket buffer size in bytes. + +wmem_default +------------ + +The default setting (in bytes) of the socket send buffer. + +wmem_max +-------- + +The maximum send socket buffer size in bytes. + +message_burst and message_cost +------------------------------ + +These parameters are used to limit the warning messages written to the kernel +log from the networking code. They enforce a rate limit to make a +denial-of-service attack impossible. A higher message_cost factor, results in +fewer messages that will be written. Message_burst controls when messages will +be dropped. The default settings limit warning messages to one every five +seconds. + +warnings +-------- + +This controls console messages from the networking stack that can occur because +of problems on the network like duplicate address or bad checksums. Normally, +this should be enabled, but if the problem persists the messages can be +disabled. + +netdev_budget +------------- + +Maximum number of packets taken from all interfaces in one polling cycle (NAPI +poll). In one polling cycle interfaces which are registered to polling are +probed in a round-robin manner. The limit of packets in one such probe can be +set per-device via sysfs class/net/<device>/weight . + +netdev_max_backlog +------------------ + +Maximum number of packets, queued on the INPUT side, when the interface +receives packets faster than kernel can process them. + +optmem_max +---------- + +Maximum ancillary buffer size allowed per socket. Ancillary data is a sequence +of struct cmsghdr structures with appended data. + +2. /proc/sys/net/unix - Parameters for Unix domain sockets +------------------------------------------------------- + +There is only one file in this directory. +unix_dgram_qlen limits the max number of datagrams queued in Unix domain +socket's buffer. It will not take effect unless PF_UNIX flag is spicified. + + +3. /proc/sys/net/ipv4 - IPV4 settings +------------------------------------------------------- +Please see: Documentation/networking/ip-sysctl.txt and ipvs-sysctl.txt for +descriptions of these entries. + + +4. Appletalk +------------------------------------------------------- + +The /proc/sys/net/appletalk directory holds the Appletalk configuration data +when Appletalk is loaded. The configurable parameters are: + +aarp-expiry-time +---------------- + +The amount of time we keep an ARP entry before expiring it. Used to age out +old hosts. + +aarp-resolve-time +----------------- + +The amount of time we will spend trying to resolve an Appletalk address. + +aarp-retransmit-limit +--------------------- + +The number of times we will retransmit a query before giving up. + +aarp-tick-time +-------------- + +Controls the rate at which expires are checked. + +The directory /proc/net/appletalk holds the list of active Appletalk sockets +on a machine. + +The fields indicate the DDP type, the local address (in network:node format) +the remote address, the size of the transmit pending queue, the size of the +received queue (bytes waiting for applications to read) the state and the uid +owning the socket. + +/proc/net/atalk_iface lists all the interfaces configured for appletalk.It +shows the name of the interface, its Appletalk address, the network range on +that address (or network number for phase 1 networks), and the status of the +interface. + +/proc/net/atalk_route lists each known network route. It lists the target +(network) that the route leads to, the router (may be directly connected), the +route flags, and the device the route is using. + + +5. IPX +------------------------------------------------------- + +The IPX protocol has no tunable values in proc/sys/net. + +The IPX protocol does, however, provide proc/net/ipx. This lists each IPX +socket giving the local and remote addresses in Novell format (that is +network:node:port). In accordance with the strange Novell tradition, +everything but the port is in hex. Not_Connected is displayed for sockets that +are not tied to a specific remote address. The Tx and Rx queue sizes indicate +the number of bytes pending for transmission and reception. The state +indicates the state the socket is in and the uid is the owning uid of the +socket. + +The /proc/net/ipx_interface file lists all IPX interfaces. For each interface +it gives the network number, the node number, and indicates if the network is +the primary network. It also indicates which device it is bound to (or +Internal for internal networks) and the Frame Type if appropriate. Linux +supports 802.3, 802.2, 802.2 SNAP and DIX (Blue Book) ethernet framing for +IPX. + +The /proc/net/ipx_route table holds a list of IPX routes. For each route it +gives the destination network, the router node (or Directly) and the network +address of the router (or Connected) for internal networks. diff --git a/Documentation/sysrq.txt b/Documentation/sysrq.txt index 9e592c718af..afa2946892d 100644 --- a/Documentation/sysrq.txt +++ b/Documentation/sysrq.txt @@ -81,6 +81,8 @@ On all - write a character to /proc/sysrq-trigger. e.g.: 'i' - Send a SIGKILL to all processes, except for init. +'j' - Forcibly "Just thaw it" - filesystems frozen by the FIFREEZE ioctl. + 'k' - Secure Access Key (SAK) Kills all programs on the current virtual console. NOTE: See important comments below in SAK section. @@ -160,6 +162,9 @@ t'E'rm and k'I'll are useful if you have some sort of runaway process you are unable to kill any other way, especially if it's spawning other processes. +"'J'ust thaw it" is useful if your system becomes unresponsive due to a frozen +(probably root) filesystem via the FIFREEZE ioctl. + * Sometimes SysRq seems to get 'stuck' after using it, what can I do? ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ That happens to me, also. I've found that tapping shift, alt, and control diff --git a/Documentation/video4linux/CARDLIST.bttv b/Documentation/video4linux/CARDLIST.bttv index 0d93fa1ac25..f11c583295e 100644 --- a/Documentation/video4linux/CARDLIST.bttv +++ b/Documentation/video4linux/CARDLIST.bttv @@ -135,7 +135,7 @@ 134 -> Adlink RTV24 135 -> DViCO FusionHDTV 5 Lite [18ac:d500] 136 -> Acorp Y878F [9511:1540] -137 -> Conceptronic CTVFMi v2 +137 -> Conceptronic CTVFMi v2 [036e:109e] 138 -> Prolink Pixelview PV-BT878P+ (Rev.2E) 139 -> Prolink PixelView PlayTV MPEG2 PV-M4900 140 -> Osprey 440 [0070:ff07] @@ -154,3 +154,7 @@ 153 -> PHYTEC VD-012 (bt878) 154 -> PHYTEC VD-012-X1 (bt878) 155 -> PHYTEC VD-012-X2 (bt878) +156 -> IVCE-8784 [0000:f050,0001:f050,0002:f050,0003:f050] +157 -> Geovision GV-800(S) (master) [800a:763d] +158 -> Geovision GV-800(S) (slave) [800b:763d,800c:763d,800d:763d] +159 -> ProVideo PV183 [1830:1540,1831:1540,1832:1540,1833:1540,1834:1540,1835:1540,1836:1540,1837:1540] diff --git a/Documentation/video4linux/CARDLIST.cx23885 b/Documentation/video4linux/CARDLIST.cx23885 index 35ea130e989..91aa3c0f0dd 100644 --- a/Documentation/video4linux/CARDLIST.cx23885 +++ b/Documentation/video4linux/CARDLIST.cx23885 @@ -12,3 +12,7 @@ 11 -> DViCO FusionHDTV DVB-T Dual Express [18ac:db78] 12 -> Leadtek Winfast PxDVR3200 H [107d:6681] 13 -> Compro VideoMate E650F [185b:e800] + 14 -> TurboSight TBS 6920 [6920:8888] + 15 -> TeVii S470 [d470:9022] + 16 -> DVBWorld DVB-S2 2005 [0001:2005] + 17 -> NetUP Dual DVB-S2 CI [1b55:2a2c] diff --git a/Documentation/video4linux/CARDLIST.cx88 b/Documentation/video4linux/CARDLIST.cx88 index 0d08f1edcf6..71e9db0b26f 100644 --- a/Documentation/video4linux/CARDLIST.cx88 +++ b/Documentation/video4linux/CARDLIST.cx88 @@ -77,3 +77,4 @@ 76 -> SATTRADE ST4200 DVB-S/S2 [b200:4200] 77 -> TBS 8910 DVB-S [8910:8888] 78 -> Prof 6200 DVB-S [b022:3022] + 79 -> Terratec Cinergy HT PCI MKII [153b:1177] diff --git a/Documentation/video4linux/CARDLIST.em28xx b/Documentation/video4linux/CARDLIST.em28xx index 75bded8a4aa..78d0a6eed57 100644 --- a/Documentation/video4linux/CARDLIST.em28xx +++ b/Documentation/video4linux/CARDLIST.em28xx @@ -7,12 +7,12 @@ 6 -> Terratec Cinergy 200 USB (em2800) 7 -> Leadtek Winfast USB II (em2800) [0413:6023] 8 -> Kworld USB2800 (em2800) - 9 -> Pinnacle Dazzle DVC 90/DVC 100 (em2820/em2840) [2304:0207,2304:021a] + 9 -> Pinnacle Dazzle DVC 90/100/101/107 / Kaiser Baas Video to DVD maker (em2820/em2840) [1b80:e302,2304:0207,2304:021a] 10 -> Hauppauge WinTV HVR 900 (em2880) [2040:6500] 11 -> Terratec Hybrid XS (em2880) [0ccd:0042] 12 -> Kworld PVR TV 2800 RF (em2820/em2840) 13 -> Terratec Prodigy XS (em2880) [0ccd:0047] - 14 -> Pixelview Prolink PlayTV USB 2.0 (em2820/em2840) + 14 -> SIIG AVTuner-PVR / Pixelview Prolink PlayTV USB 2.0 (em2820/em2840) 15 -> V-Gear PocketTV (em2800) 16 -> Hauppauge WinTV HVR 950 (em2883) [2040:6513,2040:6517,2040:651b] 17 -> Pinnacle PCTV HD Pro Stick (em2880) [2304:0227] @@ -30,7 +30,6 @@ 30 -> Videology 20K14XUSB USB2.0 (em2820/em2840) 31 -> Usbgear VD204v9 (em2821) 32 -> Supercomp USB 2.0 TV (em2821) - 33 -> SIIG AVTuner-PVR/Prolink PlayTV USB 2.0 (em2821) 34 -> Terratec Cinergy A Hybrid XS (em2860) [0ccd:004f] 35 -> Typhoon DVD Maker (em2860) 36 -> NetGMBH Cam (em2860) @@ -58,3 +57,7 @@ 58 -> Compro VideoMate ForYou/Stereo (em2820/em2840) [185b:2041] 60 -> Hauppauge WinTV HVR 850 (em2883) [2040:651f] 61 -> Pixelview PlayTV Box 4 USB 2.0 (em2820/em2840) + 62 -> Gadmei TVR200 (em2820/em2840) + 63 -> Kaiomy TVnPC U2 (em2860) [eb1a:e303] + 64 -> Easy Cap Capture DC-60 (em2860) + 65 -> IO-DATA GV-MVP/SZ (em2820/em2840) [04bb:0515] diff --git a/Documentation/video4linux/CARDLIST.saa7134 b/Documentation/video4linux/CARDLIST.saa7134 index b8d470596b0..6dacf282525 100644 --- a/Documentation/video4linux/CARDLIST.saa7134 +++ b/Documentation/video4linux/CARDLIST.saa7134 @@ -153,3 +153,5 @@ 152 -> Asus Tiger Rev:1.00 [1043:4857] 153 -> Kworld Plus TV Analog Lite PCI [17de:7128] 154 -> Avermedia AVerTV GO 007 FM Plus [1461:f31d] +155 -> Hauppauge WinTV-HVR1120 ATSC/QAM-Hybrid [0070:6706,0070:6708] +156 -> Hauppauge WinTV-HVR1110r3 [0070:6707,0070:6709,0070:670a] diff --git a/Documentation/video4linux/Zoran b/Documentation/video4linux/Zoran index 295462b2317..0e89e767629 100644 --- a/Documentation/video4linux/Zoran +++ b/Documentation/video4linux/Zoran @@ -401,8 +401,7 @@ Additional notes for software developers: first set the correct norm. Well, it seems logically correct: TV standard is "more constant" for current country than geometry settings of a variety of TV capture cards which may work in ITU or - square pixel format. Remember that users now can lock the norm to - avoid any ambiguity. + square pixel format. -- Please note that lavplay/lavrec are also included in the MJPEG-tools (http://mjpeg.sf.net/). diff --git a/Documentation/video4linux/bttv/Insmod-options b/Documentation/video4linux/bttv/Insmod-options index 5ef75787f83..bbe3ed667d9 100644 --- a/Documentation/video4linux/bttv/Insmod-options +++ b/Documentation/video4linux/bttv/Insmod-options @@ -81,16 +81,6 @@ tuner.o pal=[bdgil] select PAL variant (used for some tuners only, important for the audio carrier). -tvmixer.o - registers a mixer device for the TV card's volume/bass/treble - controls (requires a i2c audio control chip like the msp3400). - - insmod args: - debug=1 print some debug info to the syslog. - devnr=n allocate device #n (0 == /dev/mixer, - 1 = /dev/mixer1, ...), default is to - use the first free one. - tvaudio.o new, experimental module which is supported to provide a single driver for all simple i2c audio control chips (tda/tea*). diff --git a/Documentation/video4linux/bttv/README b/Documentation/video4linux/bttv/README index 7ca2154c2bf..3a367cdb664 100644 --- a/Documentation/video4linux/bttv/README +++ b/Documentation/video4linux/bttv/README @@ -63,8 +63,8 @@ If you have some knowledge and spare time, please try to fix this yourself (patches very welcome of course...) You know: The linux slogan is "Do it yourself". -There is a mailing list: video4linux-list@redhat.com. -https://listman.redhat.com/mailman/listinfo/video4linux-list +There is a mailing list: linux-media@vger.kernel.org +http://vger.kernel.org/vger-lists.html#linux-media If you have trouble with some specific TV card, try to ask there instead of mailing me directly. The chance that someone with the diff --git a/Documentation/video4linux/cx2341x/README.hm12 b/Documentation/video4linux/cx2341x/README.hm12 index 0e213ed095e..b36148ea075 100644 --- a/Documentation/video4linux/cx2341x/README.hm12 +++ b/Documentation/video4linux/cx2341x/README.hm12 @@ -32,6 +32,10 @@ Y, U and V planes. This code assumes frames of 720x576 (PAL) pixels. The width of a frame is always 720 pixels, regardless of the actual specified width. +If the height is not a multiple of 32 lines, then the captured video is +missing macroblocks at the end and is unusable. So the height must be a +multiple of 32. + -------------------------------------------------------------------------- #include <stdio.h> diff --git a/Documentation/video4linux/gspca.txt b/Documentation/video4linux/gspca.txt index 1c58a763014..98529e03a46 100644 --- a/Documentation/video4linux/gspca.txt +++ b/Documentation/video4linux/gspca.txt @@ -32,6 +32,7 @@ spca561 041e:403b Creative Webcam Vista (VF0010) zc3xx 041e:4051 Creative Live!Cam Notebook Pro (VF0250) ov519 041e:4052 Creative Live! VISTA IM zc3xx 041e:4053 Creative Live!Cam Video IM +vc032x 041e:405b Creative Live! Cam Notebook Ultra (VC0130) ov519 041e:405f Creative Live! VISTA VF0330 ov519 041e:4060 Creative Live! VISTA VF0350 ov519 041e:4061 Creative Live! VISTA VF0400 @@ -193,6 +194,7 @@ spca500 084d:0003 D-Link DSC-350 spca500 08ca:0103 Aiptek PocketDV sunplus 08ca:0104 Aiptek PocketDVII 1.3 sunplus 08ca:0106 Aiptek Pocket DV3100+ +mr97310a 08ca:0111 Aiptek PenCam VGA+ sunplus 08ca:2008 Aiptek Mini PenCam 2 M sunplus 08ca:2010 Aiptek PocketCam 3M sunplus 08ca:2016 Aiptek PocketCam 2 Mega @@ -215,6 +217,7 @@ pac207 093a:2468 PAC207 pac207 093a:2470 Genius GF112 pac207 093a:2471 Genius VideoCam ge111 pac207 093a:2472 Genius VideoCam ge110 +pac207 093a:2474 Genius iLook 111 pac207 093a:2476 Genius e-Messenger 112 pac7311 093a:2600 PAC7311 Typhoon pac7311 093a:2601 Philips SPC 610 NC @@ -279,6 +282,7 @@ spca561 10fd:7e50 FlyCam Usb 100 zc3xx 10fd:8050 Typhoon Webshot II USB 300k ov534 1415:2000 Sony HD Eye for PS3 (SLEH 00201) pac207 145f:013a Trust WB-1300N +vc032x 15b8:6001 HP 2.0 Megapixel vc032x 15b8:6002 HP 2.0 Megapixel rz406aa spca501 1776:501c Arowana 300K CMOS Camera t613 17a1:0128 TASCORP JPEG Webcam, NGS Cyclops diff --git a/Documentation/video4linux/si470x.txt b/Documentation/video4linux/si470x.txt index 49679e6aaa7..3a7823e01b4 100644 --- a/Documentation/video4linux/si470x.txt +++ b/Documentation/video4linux/si470x.txt @@ -1,6 +1,6 @@ Driver for USB radios for the Silicon Labs Si470x FM Radio Receivers -Copyright (c) 2008 Tobias Lorenz <tobias.lorenz@gmx.net> +Copyright (c) 2009 Tobias Lorenz <tobias.lorenz@gmx.net> Information from Silicon Labs @@ -41,7 +41,7 @@ chips are known to work: - 10c4:818a: Silicon Labs USB FM Radio Reference Design - 06e1:a155: ADS/Tech FM Radio Receiver (formerly Instant FM Music) (RDX-155-EF) - 1b80:d700: KWorld USB FM Radio SnapMusic Mobile 700 (FM700) -- 10c5:819a: DealExtreme USB Radio +- 10c5:819a: Sanei Electric, Inc. FM USB Radio (sold as DealExtreme.com PCear) Software @@ -52,6 +52,7 @@ Testing is usually done with most application under Debian/testing: - gradio - GTK FM radio tuner - kradio - Comfortable Radio Application for KDE - radio - ncurses-based radio application +- mplayer - The Ultimate Movie Player For Linux There is also a library libv4l, which can be used. It's going to have a function for frequency seeking, either by using hardware functionality as in radio-si470x @@ -69,7 +70,7 @@ Audio Listing USB Audio is provided by the ALSA snd_usb_audio module. It is recommended to also select SND_USB_AUDIO, as this is required to get sound from the radio. For listing you have to redirect the sound, for example using one of the following -commands. +commands. Please adjust the audio devices to your needs (/dev/dsp* and hw:x,x). If you just want to test audio (very poor quality): cat /dev/dsp1 > /dev/dsp @@ -80,6 +81,10 @@ sox -2 --endian little -r 96000 -t oss /dev/dsp1 -t oss /dev/dsp If you use arts try: arecord -D hw:1,0 -r96000 -c2 -f S16_LE | artsdsp aplay -B - +If you use mplayer try: +mplayer -radio adevice=hw=1.0:arate=96000 \ + -rawaudio rate=96000 \ + radio://<frequency>/capture Module Parameters ================= diff --git a/Documentation/video4linux/v4l2-framework.txt b/Documentation/video4linux/v4l2-framework.txt index ff124374e9b..a31177390e5 100644 --- a/Documentation/video4linux/v4l2-framework.txt +++ b/Documentation/video4linux/v4l2-framework.txt @@ -47,7 +47,9 @@ All drivers have the following structure: 3) Creating V4L2 device nodes (/dev/videoX, /dev/vbiX, /dev/radioX and /dev/vtxX) and keeping track of device-node specific data. -4) Filehandle-specific structs containing per-filehandle data. +4) Filehandle-specific structs containing per-filehandle data; + +5) video buffer handling. This is a rough schematic of how it all relates: @@ -82,12 +84,20 @@ You must register the device instance: v4l2_device_register(struct device *dev, struct v4l2_device *v4l2_dev); Registration will initialize the v4l2_device struct and link dev->driver_data -to v4l2_dev. Registration will also set v4l2_dev->name to a value derived from -dev (driver name followed by the bus_id, to be precise). You may change the -name after registration if you want. +to v4l2_dev. If v4l2_dev->name is empty then it will be set to a value derived +from dev (driver name followed by the bus_id, to be precise). If you set it +up before calling v4l2_device_register then it will be untouched. If dev is +NULL, then you *must* setup v4l2_dev->name before calling v4l2_device_register. The first 'dev' argument is normally the struct device pointer of a pci_dev, -usb_device or platform_device. +usb_device or platform_device. It is rare for dev to be NULL, but it happens +with ISA devices or when one device creates multiple PCI devices, thus making +it impossible to associate v4l2_dev with a particular parent. + +You can also supply a notify() callback that can be called by sub-devices to +notify you of events. Whether you need to set this depends on the sub-device. +Any notifications a sub-device supports must be defined in a header in +include/media/<subdevice>.h. You unregister with: @@ -95,6 +105,17 @@ You unregister with: Unregistering will also automatically unregister all subdevs from the device. +If you have a hotpluggable device (e.g. a USB device), then when a disconnect +happens the parent device becomes invalid. Since v4l2_device has a pointer to +that parent device it has to be cleared as well to mark that the parent is +gone. To do this call: + + v4l2_device_disconnect(struct v4l2_device *v4l2_dev); + +This does *not* unregister the subdevs, so you still need to call the +v4l2_device_unregister() function for that. If your driver is not hotpluggable, +then there is no need to call v4l2_device_disconnect(). + Sometimes you need to iterate over all devices registered by a specific driver. This is usually the case if multiple device drivers use the same hardware. E.g. the ivtvfb driver is a framebuffer driver that uses the ivtv @@ -134,7 +155,7 @@ The recommended approach is as follows: static atomic_t drv_instance = ATOMIC_INIT(0); -static int __devinit drv_probe(struct pci_dev *dev, +static int __devinit drv_probe(struct pci_dev *pdev, const struct pci_device_id *pci_id) { ... @@ -218,7 +239,7 @@ to add new ops and categories. A sub-device driver initializes the v4l2_subdev struct using: - v4l2_subdev_init(subdev, &ops); + v4l2_subdev_init(sd, &ops); Afterwards you need to initialize subdev->name with a unique name and set the module owner. This is done for you if you use the i2c helper functions. @@ -226,7 +247,7 @@ module owner. This is done for you if you use the i2c helper functions. A device (bridge) driver needs to register the v4l2_subdev with the v4l2_device: - int err = v4l2_device_register_subdev(device, subdev); + int err = v4l2_device_register_subdev(v4l2_dev, sd); This can fail if the subdev module disappeared before it could be registered. After this function was called successfully the subdev->dev field points to @@ -234,17 +255,17 @@ the v4l2_device. You can unregister a sub-device using: - v4l2_device_unregister_subdev(subdev); + v4l2_device_unregister_subdev(sd); -Afterwards the subdev module can be unloaded and subdev->dev == NULL. +Afterwards the subdev module can be unloaded and sd->dev == NULL. You can call an ops function either directly: - err = subdev->ops->core->g_chip_ident(subdev, &chip); + err = sd->ops->core->g_chip_ident(sd, &chip); but it is better and easier to use this macro: - err = v4l2_subdev_call(subdev, core, g_chip_ident, &chip); + err = v4l2_subdev_call(sd, core, g_chip_ident, &chip); The macro will to the right NULL pointer checks and returns -ENODEV if subdev is NULL, -ENOIOCTLCMD if either subdev->core or subdev->core->g_chip_ident is @@ -252,19 +273,19 @@ NULL, or the actual result of the subdev->ops->core->g_chip_ident ops. It is also possible to call all or a subset of the sub-devices: - v4l2_device_call_all(dev, 0, core, g_chip_ident, &chip); + v4l2_device_call_all(v4l2_dev, 0, core, g_chip_ident, &chip); Any subdev that does not support this ops is skipped and error results are ignored. If you want to check for errors use this: - err = v4l2_device_call_until_err(dev, 0, core, g_chip_ident, &chip); + err = v4l2_device_call_until_err(v4l2_dev, 0, core, g_chip_ident, &chip); Any error except -ENOIOCTLCMD will exit the loop with that error. If no errors (except -ENOIOCTLCMD) occured, then 0 is returned. The second argument to both calls is a group ID. If 0, then all subdevs are called. If non-zero, then only those whose group ID match that value will -be called. Before a bridge driver registers a subdev it can set subdev->grp_id +be called. Before a bridge driver registers a subdev it can set sd->grp_id to whatever value it wants (it's 0 by default). This value is owned by the bridge driver and the sub-device driver will never modify or use it. @@ -276,6 +297,11 @@ e.g. AUDIO_CONTROLLER and specify that as the group ID value when calling v4l2_device_call_all(). That ensures that it will only go to the subdev that needs it. +If the sub-device needs to notify its v4l2_device parent of an event, then +it can call v4l2_subdev_notify(sd, notification, arg). This macro checks +whether there is a notify() callback defined and returns -ENODEV if not. +Otherwise the result of the notify() call is returned. + The advantage of using v4l2_subdev is that it is a generic struct and does not contain any knowledge about the underlying hardware. So a driver might contain several subdevs that use an I2C bus, but also a subdev that is @@ -340,6 +366,12 @@ Make sure to call v4l2_device_unregister_subdev(sd) when the remove() callback is called. This will unregister the sub-device from the bridge driver. It is safe to call this even if the sub-device was never registered. +You need to do this because when the bridge driver destroys the i2c adapter +the remove() callbacks are called of the i2c devices on that adapter. +After that the corresponding v4l2_subdev structures are invalid, so they +have to be unregistered first. Calling v4l2_device_unregister_subdev(sd) +from the remove() callback ensures that this is always done correctly. + The bridge driver also has some helper functions it can use: @@ -349,8 +381,8 @@ This loads the given module (can be NULL if no module needs to be loaded) and calls i2c_new_device() with the given i2c_adapter and chip/address arguments. If all goes well, then it registers the subdev with the v4l2_device. It gets the v4l2_device by calling i2c_get_adapdata(adapter), so you should make sure -that adapdata is set to v4l2_device when you setup the i2c_adapter in your -driver. +to call i2c_set_adapdata(adapter, v4l2_device) when you setup the i2c_adapter +in your driver. You can also use v4l2_i2c_new_probed_subdev() which is very similar to v4l2_i2c_new_subdev(), except that it has an array of possible I2C addresses @@ -358,6 +390,14 @@ that it should probe. Internally it calls i2c_new_probed_device(). Both functions return NULL if something went wrong. +Note that the chipid you pass to v4l2_i2c_new_(probed_)subdev() is usually +the same as the module name. It allows you to specify a chip variant, e.g. +"saa7114" or "saa7115". In general though the i2c driver autodetects this. +The use of chipid is something that needs to be looked at more closely at a +later date. It differs between i2c drivers and as such can be confusing. +To see which chip variants are supported you can look in the i2c driver code +for the i2c_device_id table. This lists all the possibilities. + struct video_device ------------------- @@ -396,6 +436,15 @@ You should also set these fields: - ioctl_ops: if you use the v4l2_ioctl_ops to simplify ioctl maintenance (highly recommended to use this and it might become compulsory in the future!), then set this to your v4l2_ioctl_ops struct. +- parent: you only set this if v4l2_device was registered with NULL as + the parent device struct. This only happens in cases where one hardware + device has multiple PCI devices that all share the same v4l2_device core. + + The cx88 driver is an example of this: one core v4l2_device struct, but + it is used by both an raw video PCI device (cx8800) and a MPEG PCI device + (cx8802). Since the v4l2_device cannot be associated with a particular + PCI device it is setup without a parent device. But when the struct + video_device is setup you do know which parent PCI device to use. If you use v4l2_ioctl_ops, then you should set either .unlocked_ioctl or .ioctl to video_ioctl2 in your v4l2_file_operations struct. @@ -499,8 +548,8 @@ There are a few useful helper functions: You can set/get driver private data in the video_device struct using: -void *video_get_drvdata(struct video_device *dev); -void video_set_drvdata(struct video_device *dev, void *data); +void *video_get_drvdata(struct video_device *vdev); +void video_set_drvdata(struct video_device *vdev, void *data); Note that you can safely call video_set_drvdata() before calling video_register_device(). @@ -519,3 +568,103 @@ void *video_drvdata(struct file *file); You can go from a video_device struct to the v4l2_device struct using: struct v4l2_device *v4l2_dev = vdev->v4l2_dev; + +video buffer helper functions +----------------------------- + +The v4l2 core API provides a standard method for dealing with video +buffers. Those methods allow a driver to implement read(), mmap() and +overlay() on a consistent way. + +There are currently methods for using video buffers on devices that +supports DMA with scatter/gather method (videobuf-dma-sg), DMA with +linear access (videobuf-dma-contig), and vmalloced buffers, mostly +used on USB drivers (videobuf-vmalloc). + +Any driver using videobuf should provide operations (callbacks) for +four handlers: + +ops->buf_setup - calculates the size of the video buffers and avoid they + to waste more than some maximum limit of RAM; +ops->buf_prepare - fills the video buffer structs and calls + videobuf_iolock() to alloc and prepare mmaped memory; +ops->buf_queue - advices the driver that another buffer were + requested (by read() or by QBUF); +ops->buf_release - frees any buffer that were allocated. + +In order to use it, the driver need to have a code (generally called at +interrupt context) that will properly handle the buffer request lists, +announcing that a new buffer were filled. + +The irq handling code should handle the videobuf task lists, in order +to advice videobuf that a new frame were filled, in order to honor to a +request. The code is generally like this one: + if (list_empty(&dma_q->active)) + return; + + buf = list_entry(dma_q->active.next, struct vbuffer, vb.queue); + + if (!waitqueue_active(&buf->vb.done)) + return; + + /* Some logic to handle the buf may be needed here */ + + list_del(&buf->vb.queue); + do_gettimeofday(&buf->vb.ts); + wake_up(&buf->vb.done); + +Those are the videobuffer functions used on drivers, implemented on +videobuf-core: + +- Videobuf init functions + videobuf_queue_sg_init() + Initializes the videobuf infrastructure. This function should be + called before any other videobuf function on drivers that uses DMA + Scatter/Gather buffers. + + videobuf_queue_dma_contig_init + Initializes the videobuf infrastructure. This function should be + called before any other videobuf function on drivers that need DMA + contiguous buffers. + + videobuf_queue_vmalloc_init() + Initializes the videobuf infrastructure. This function should be + called before any other videobuf function on USB (and other drivers) + that need a vmalloced type of videobuf. + +- videobuf_iolock() + Prepares the videobuf memory for the proper method (read, mmap, overlay). + +- videobuf_queue_is_busy() + Checks if a videobuf is streaming. + +- videobuf_queue_cancel() + Stops video handling. + +- videobuf_mmap_free() + frees mmap buffers. + +- videobuf_stop() + Stops video handling, ends mmap and frees mmap and other buffers. + +- V4L2 api functions. Those functions correspond to VIDIOC_foo ioctls: + videobuf_reqbufs(), videobuf_querybuf(), videobuf_qbuf(), + videobuf_dqbuf(), videobuf_streamon(), videobuf_streamoff(). + +- V4L1 api function (corresponds to VIDIOCMBUF ioctl): + videobuf_cgmbuf() + This function is used to provide backward compatibility with V4L1 + API. + +- Some help functions for read()/poll() operations: + videobuf_read_stream() + For continuous stream read() + videobuf_read_one() + For snapshot read() + videobuf_poll_stream() + polling help function + +The better way to understand it is to take a look at vivi driver. One +of the main reasons for vivi is to be a videobuf usage example. the +vivi_thread_tick() does the task that the IRQ callback would do on PCI +drivers (or the irq callback on USB). diff --git a/Documentation/video4linux/v4lgrab.c b/Documentation/video4linux/v4lgrab.c index d6e70bef8ad..05769cff100 100644 --- a/Documentation/video4linux/v4lgrab.c +++ b/Documentation/video4linux/v4lgrab.c @@ -105,8 +105,8 @@ int main(int argc, char ** argv) struct video_picture vpic; unsigned char *buffer, *src; - int bpp = 24, r, g, b; - unsigned int i, src_depth; + int bpp = 24, r = 0, g = 0, b = 0; + unsigned int i, src_depth = 16; if (fd < 0) { perror(VIDEO_DEV); diff --git a/Documentation/video4linux/zr364xx.txt b/Documentation/video4linux/zr364xx.txt index 5c81e3ae645..7f3d1955d21 100644 --- a/Documentation/video4linux/zr364xx.txt +++ b/Documentation/video4linux/zr364xx.txt @@ -65,3 +65,4 @@ Vendor Product Distributor Model 0x06d6 0x003b Trust Powerc@m 970Z 0x0a17 0x004e Pentax Optio 50 0x041e 0x405d Creative DiVi CAM 516 +0x08ca 0x2102 Aiptek DV T300 diff --git a/Documentation/x86/earlyprintk.txt b/Documentation/x86/earlyprintk.txt new file mode 100644 index 00000000000..607b1a01606 --- /dev/null +++ b/Documentation/x86/earlyprintk.txt @@ -0,0 +1,101 @@ + +Mini-HOWTO for using the earlyprintk=dbgp boot option with a +USB2 Debug port key and a debug cable, on x86 systems. + +You need two computers, the 'USB debug key' special gadget and +and two USB cables, connected like this: + + [host/target] <-------> [USB debug key] <-------> [client/console] + +1. There are three specific hardware requirements: + + a.) Host/target system needs to have USB debug port capability. + + You can check this capability by looking at a 'Debug port' bit in + the lspci -vvv output: + + # lspci -vvv + ... + 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI]) + Subsystem: Lenovo ThinkPad T61 + Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- + Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- + Latency: 0 + Interrupt: pin D routed to IRQ 19 + Region 0: Memory at fe227000 (32-bit, non-prefetchable) [size=1K] + Capabilities: [50] Power Management version 2 + Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) + Status: D0 PME-Enable- DSel=0 DScale=0 PME+ + Capabilities: [58] Debug port: BAR=1 offset=00a0 + ^^^^^^^^^^^ <==================== [ HERE ] + Kernel driver in use: ehci_hcd + Kernel modules: ehci-hcd + ... + +( If your system does not list a debug port capability then you probably + wont be able to use the USB debug key. ) + + b.) You also need a Netchip USB debug cable/key: + + http://www.plxtech.com/products/NET2000/NET20DC/default.asp + + This is a small blue plastic connector with two USB connections, + it draws power from its USB connections. + + c.) Thirdly, you need a second client/console system with a regular USB port. + +2. Software requirements: + + a.) On the host/target system: + + You need to enable the following kernel config option: + + CONFIG_EARLY_PRINTK_DBGP=y + + And you need to add the boot command line: "earlyprintk=dbgp". + (If you are using Grub, append it to the 'kernel' line in + /etc/grub.conf) + + NOTE: normally earlyprintk console gets turned off once the + regular console is alive - use "earlyprintk=dbgp,keep" to keep + this channel open beyond early bootup. This can be useful for + debugging crashes under Xorg, etc. + + b.) On the client/console system: + + You should enable the following kernel config option: + + CONFIG_USB_SERIAL_DEBUG=y + + On the next bootup with the modified kernel you should + get a /dev/ttyUSBx device(s). + + Now this channel of kernel messages is ready to be used: start + your favorite terminal emulator (minicom, etc.) and set + it up to use /dev/ttyUSB0 - or use a raw 'cat /dev/ttyUSBx' to + see the raw output. + + c.) On Nvidia Southbridge based systems: the kernel will try to probe + and find out which port has debug device connected. + +3. Testing that it works fine: + + You can test the output by using earlyprintk=dbgp,keep and provoking + kernel messages on the host/target system. You can provoke a harmless + kernel message by for example doing: + + echo h > /proc/sysrq-trigger + + On the host/target system you should see this help line in "dmesg" output: + + SysRq : HELP : loglevel(0-9) reBoot Crashdump terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) saK show-backtrace-all-active-cpus(L) show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z) + + On the client/console system do: + + cat /dev/ttyUSB0 + + And you should see the help line above displayed shortly after you've + provoked it on the host system. + +If it does not work then please ask about it on the linux-kernel@vger.kernel.org +mailing list or contact the x86 maintainers. |