diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/video/fsl,imx-fb.txt | 51 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/video/ssd1307fb.txt | 10 |
2 files changed, 58 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt new file mode 100644 index 00000000000..46da08db186 --- /dev/null +++ b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt @@ -0,0 +1,51 @@ +Freescale imx21 Framebuffer + +This framebuffer driver supports devices imx1, imx21, imx25, and imx27. + +Required properties: +- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21 +- reg : Should contain 1 register ranges(address and length) +- interrupts : One interrupt of the fb dev + +Required nodes: +- display: Phandle to a display node as described in + Documentation/devicetree/bindings/video/display-timing.txt + Additional, the display node has to define properties: + - bits-per-pixel: Bits per pixel + - fsl,pcr: LCDC PCR value + +Optional properties: +- fsl,dmacr: DMA Control Register value. This is optional. By default, the + register is not modified as recommended by the datasheet. +- fsl,lscr1: LCDC Sharp Configuration Register value. + +Example: + + imxfb: fb@10021000 { + compatible = "fsl,imx21-fb"; + interrupts = <61>; + reg = <0x10021000 0x1000>; + display = <&display0>; + }; + + ... + + display0: display0 { + model = "Primeview-PD050VL1"; + native-mode = <&timing_disp0>; + bits-per-pixel = <16>; + fsl,pcr = <0xf0c88080>; /* non-standard but required */ + display-timings { + timing_disp0: 640x480 { + hactive = <640>; + vactive = <480>; + hback-porch = <112>; + hfront-porch = <36>; + hsync-len = <32>; + vback-porch = <33>; + vfront-porch = <33>; + vsync-len = <2>; + clock-frequency = <25000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt b/Documentation/devicetree/bindings/video/ssd1307fb.txt index 3d0060cff06..7a125427ff4 100644 --- a/Documentation/devicetree/bindings/video/ssd1307fb.txt +++ b/Documentation/devicetree/bindings/video/ssd1307fb.txt @@ -1,13 +1,17 @@ * Solomon SSD1307 Framebuffer Driver Required properties: - - compatible: Should be "solomon,ssd1307fb-<bus>". The only supported bus for - now is i2c. + - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for + now is i2c, and the supported chips are ssd1306 and ssd1307. - reg: Should contain address of the controller on the I2C bus. Most likely 0x3c or 0x3d - pwm: Should contain the pwm to use according to the OF device tree PWM - specification [0] + specification [0]. Only required for the ssd1307. - reset-gpios: Should contain the GPIO used to reset the OLED display + - solomon,height: Height in pixel of the screen driven by the controller + - solomon,width: Width in pixel of the screen driven by the controller + - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is + mapped to. Optional properties: - reset-active-low: Is the reset gpio is active on physical low? |