diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/DMA-API-HOWTO.txt | 126 | ||||
| -rw-r--r-- | Documentation/DMA-API.txt | 12 |
2 files changed, 138 insertions, 0 deletions
diff --git a/Documentation/DMA-API-HOWTO.txt b/Documentation/DMA-API-HOWTO.txt index a0b6250add7..4a4fb295cee 100644 --- a/Documentation/DMA-API-HOWTO.txt +++ b/Documentation/DMA-API-HOWTO.txt @@ -468,11 +468,46 @@ To map a single region, you do: size_t size = buffer->len; dma_handle = dma_map_single(dev, addr, size, direction); + if (dma_mapping_error(dma_handle)) { + /* + * reduce current DMA mapping usage, + * delay and try again later or + * reset driver. + */ + goto map_error_handling; + } and to unmap it: dma_unmap_single(dev, dma_handle, size, direction); +You should call dma_mapping_error() as dma_map_single() could fail and return +error. Not all dma implementations support dma_mapping_error() interface. +However, it is a good practice to call dma_mapping_error() interface, which +will invoke the generic mapping error check interface. Doing so will ensure +that the mapping code will work correctly on all dma implementations without +any dependency on the specifics of the underlying implementation. Using the +returned address without checking for errors could result in failures ranging +from panics to silent data corruption. Couple of example of incorrect ways to +check for errors that make assumptions about the underlying dma implementation +are as follows and these are applicable to dma_map_page() as well. + +Incorrect example 1: + dma_addr_t dma_handle; + + dma_handle = dma_map_single(dev, addr, size, direction); + if ((dma_handle & 0xffff != 0) || (dma_handle >= 0x1000000)) { + goto map_error; + } + +Incorrect example 2: + dma_addr_t dma_handle; + + dma_handle = dma_map_single(dev, addr, size, direction); + if (dma_handle == DMA_ERROR_CODE) { + goto map_error; + } + You should call dma_unmap_single when the DMA activity is finished, e.g. from the interrupt which told you that the DMA transfer is done. @@ -489,6 +524,14 @@ Specifically: size_t size = buffer->len; dma_handle = dma_map_page(dev, page, offset, size, direction); + if (dma_mapping_error(dma_handle)) { + /* + * reduce current DMA mapping usage, + * delay and try again later or + * reset driver. + */ + goto map_error_handling; + } ... @@ -496,6 +539,12 @@ Specifically: Here, "offset" means byte offset within the given page. +You should call dma_mapping_error() as dma_map_page() could fail and return +error as outlined under the dma_map_single() discussion. + +You should call dma_unmap_page when the DMA activity is finished, e.g. +from the interrupt which told you that the DMA transfer is done. + With scatterlists, you map a region gathered from several regions by: int i, count = dma_map_sg(dev, sglist, nents, direction); @@ -578,6 +627,14 @@ to use the dma_sync_*() interfaces. dma_addr_t mapping; mapping = dma_map_single(cp->dev, buffer, len, DMA_FROM_DEVICE); + if (dma_mapping_error(dma_handle)) { + /* + * reduce current DMA mapping usage, + * delay and try again later or + * reset driver. + */ + goto map_error_handling; + } cp->rx_buf = buffer; cp->rx_len = len; @@ -658,6 +715,75 @@ failure can be determined by: * delay and try again later or * reset driver. */ + goto map_error_handling; + } + +- unmap pages that are already mapped, when mapping error occurs in the middle + of a multiple page mapping attempt. These example are applicable to + dma_map_page() as well. + +Example 1: + dma_addr_t dma_handle1; + dma_addr_t dma_handle2; + + dma_handle1 = dma_map_single(dev, addr, size, direction); + if (dma_mapping_error(dev, dma_handle1)) { + /* + * reduce current DMA mapping usage, + * delay and try again later or + * reset driver. + */ + goto map_error_handling1; + } + dma_handle2 = dma_map_single(dev, addr, size, direction); + if (dma_mapping_error(dev, dma_handle2)) { + /* + * reduce current DMA mapping usage, + * delay and try again later or + * reset driver. + */ + goto map_error_handling2; + } + + ... + + map_error_handling2: + dma_unmap_single(dma_handle1); + map_error_handling1: + +Example 2: (if buffers are allocated a loop, unmap all mapped buffers when + mapping error is detected in the middle) + + dma_addr_t dma_addr; + dma_addr_t array[DMA_BUFFERS]; + int save_index = 0; + + for (i = 0; i < DMA_BUFFERS; i++) { + + ... + + dma_addr = dma_map_single(dev, addr, size, direction); + if (dma_mapping_error(dev, dma_addr)) { + /* + * reduce current DMA mapping usage, + * delay and try again later or + * reset driver. + */ + goto map_error_handling; + } + array[i].dma_addr = dma_addr; + save_index++; + } + + ... + + map_error_handling: + + for (i = 0; i < save_index; i++) { + + ... + + dma_unmap_single(array[i].dma_addr); } Networking drivers must call dev_kfree_skb to free the socket buffer diff --git a/Documentation/DMA-API.txt b/Documentation/DMA-API.txt index 66bd97a95f1..78a6c569d20 100644 --- a/Documentation/DMA-API.txt +++ b/Documentation/DMA-API.txt @@ -678,3 +678,15 @@ out of dma_debug_entries. These entries are preallocated at boot. The number of preallocated entries is defined per architecture. If it is too low for you boot with 'dma_debug_entries=<your_desired_number>' to overwrite the architectural default. + +void debug_dmap_mapping_error(struct device *dev, dma_addr_t dma_addr); + +dma-debug interface debug_dma_mapping_error() to debug drivers that fail +to check dma mapping errors on addresses returned by dma_map_single() and +dma_map_page() interfaces. This interface clears a flag set by +debug_dma_map_page() to indicate that dma_mapping_error() has been called by +the driver. When driver does unmap, debug_dma_unmap() checks the flag and if +this flag is still set, prints warning message that includes call trace that +leads up to the unmap. This interface can be called from dma_mapping_error() +routines to enable dma mapping error check debugging. + |