diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/DocBook/drm.tmpl | 7 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/drm/tilcdc/panel.txt | 59 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/drm/tilcdc/slave.txt | 18 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt | 21 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt | 21 | ||||
| -rw-r--r-- | Documentation/thermal/nouveau_thermal | 81 |
6 files changed, 207 insertions, 0 deletions
diff --git a/Documentation/DocBook/drm.tmpl b/Documentation/DocBook/drm.tmpl index b26de523ab7..a6428ddfcfc 100644 --- a/Documentation/DocBook/drm.tmpl +++ b/Documentation/DocBook/drm.tmpl @@ -1161,6 +1161,12 @@ int max_width, max_height;</synopsis> any new rendering to the frame buffer until the page flip completes. </para> <para> + If a page flip can be successfully scheduled the driver must set the + <code>drm_crtc-<fb</code> field to the new framebuffer pointed to + by <code>fb</code>. This is important so that the reference counting + on framebuffers stays balanced. + </para> + <para> If a page flip is already pending, the <methodname>page_flip</methodname> operation must return -<errorname>EBUSY</errorname>. @@ -2143,6 +2149,7 @@ void intel_crt_init(struct drm_device *dev) <title>fbdev Helper Functions Reference</title> !Pdrivers/gpu/drm/drm_fb_helper.c fbdev helpers !Edrivers/gpu/drm/drm_fb_helper.c +!Iinclude/drm/drm_fb_helper.h </sect2> <sect2> <title>Display Port Helper Functions Reference</title> diff --git a/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt new file mode 100644 index 00000000000..9301c330d1a --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt @@ -0,0 +1,59 @@ +Device-Tree bindings for tilcdc DRM generic panel output driver + +Required properties: + - compatible: value should be "ti,tilcdc,panel". + - panel-info: configuration info to configure LCDC correctly for the panel + - ac-bias: AC Bias Pin Frequency + - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt + - dma-burst-sz: DMA burst size + - bpp: Bits per pixel + - fdd: FIFO DMA Request Delay + - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling + - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore + - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most + - fifo-th: DMA FIFO threshold + - display-timings: typical videomode of lcd panel. Multiple video modes + can be listed if the panel supports multiple timings, but the 'native-mode' + should be the preferred/default resolution. Refer to + Documentation/devicetree/bindings/video/display-timing.txt for display + timing binding details. + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + /* Settings for CDTech_S035Q01 / LCD3 cape: */ + lcd3 { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <16>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + display-timings { + native-mode = <&timing0>; + timing0: 320x240 { + hactive = <320>; + vactive = <240>; + hback-porch = <21>; + hfront-porch = <58>; + hsync-len = <47>; + vback-porch = <11>; + vfront-porch = <23>; + vsync-len = <2>; + clock-frequency = <8000000>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/slave.txt b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt new file mode 100644 index 00000000000..3d2c52460dc --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt @@ -0,0 +1,18 @@ +Device-Tree bindings for tilcdc DRM encoder slave output driver + +Required properties: + - compatible: value should be "ti,tilcdc,slave". + - i2c: the phandle for the i2c device the encoder slave is connected to + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + hdmi { + compatible = "ti,tilcdc,slave"; + i2c = <&i2c0>; + pinctrl-names = "default"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt new file mode 100644 index 00000000000..a58ae7756fc --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt @@ -0,0 +1,21 @@ +Device-Tree bindings for tilcdc DRM TFP410 output driver + +Required properties: + - compatible: value should be "ti,tilcdc,tfp410". + - i2c: the phandle for the i2c device to use for DDC + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + - powerdn-gpio: the powerdown GPIO, pulled low to power down the + TFP410 device (for DPMS_OFF) + +Example: + + dvicape { + compatible = "ti,tilcdc,tfp410"; + i2c = <&i2c2>; + pinctrl-names = "default"; + pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>; + powerdn-gpio = <&gpio2 31 0>; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt new file mode 100644 index 00000000000..e5f130159ae --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt @@ -0,0 +1,21 @@ +Device-Tree bindings for tilcdc DRM driver + +Required properties: + - compatible: value should be "ti,am33xx-tilcdc". + - interrupts: the interrupt number + - reg: base address and size of the LCDC device + +Recommended properties: + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + - ti,hwmods: Name of the hwmod associated to the LCDC + +Example: + + fb: fb@4830e000 { + compatible = "ti,am33xx-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + }; diff --git a/Documentation/thermal/nouveau_thermal b/Documentation/thermal/nouveau_thermal new file mode 100644 index 00000000000..efceb7828f5 --- /dev/null +++ b/Documentation/thermal/nouveau_thermal @@ -0,0 +1,81 @@ +Kernel driver nouveau +=================== + +Supported chips: +* NV43+ + +Authors: Martin Peres (mupuf) <martin.peres@labri.fr> + +Description +--------- + +This driver allows to read the GPU core temperature, drive the GPU fan and +set temperature alarms. + +Currently, due to the absence of in-kernel API to access HWMON drivers, Nouveau +cannot access any of the i2c external monitoring chips it may find. If you +have one of those, temperature and/or fan management through Nouveau's HWMON +interface is likely not to work. This document may then not cover your situation +entirely. + +Temperature management +-------------------- + +Temperature is exposed under as a read-only HWMON attribute temp1_input. + +In order to protect the GPU from overheating, Nouveau supports 4 configurable +temperature thresholds: + + * Fan_boost: Fan speed is set to 100% when reaching this temperature; + * Downclock: The GPU will be downclocked to reduce its power dissipation; + * Critical: The GPU is put on hold to further lower power dissipation; + * Shutdown: Shut the computer down to protect your GPU. + +WARNING: Some of these thresholds may not be used by Nouveau depending +on your chipset. + +The default value for these thresholds comes from the GPU's vbios. These +thresholds can be configured thanks to the following HWMON attributes: + + * Fan_boost: temp1_auto_point1_temp and temp1_auto_point1_temp_hyst; + * Downclock: temp1_max and temp1_max_hyst; + * Critical: temp1_crit and temp1_crit_hyst; + * Shutdown: temp1_emergency and temp1_emergency_hyst. + +NOTE: Remember that the values are stored as milli degrees Celcius. Don't forget +to multiply! + +Fan management +------------ + +Not all cards have a drivable fan. If you do, then the following HWMON +attributes should be available: + + * pwm1_enable: Current fan management mode (NONE, MANUAL or AUTO); + * pwm1: Current PWM value (power percentage); + * pwm1_min: The minimum PWM speed allowed; + * pwm1_max: The maximum PWM speed allowed (bypassed when hitting Fan_boost); + +You may also have the following attribute: + + * fan1_input: Speed in RPM of your fan. + +Your fan can be driven in different modes: + + * 0: The fan is left untouched; + * 1: The fan can be driven in manual (use pwm1 to change the speed); + * 2; The fan is driven automatically depending on the temperature. + +NOTE: Be sure to use the manual mode if you want to drive the fan speed manually + +NOTE2: Not all fan management modes may be supported on all chipsets. We are +working on it. + +Bug reports +--------- + +Thermal management on Nouveau is new and may not work on all cards. If you have +inquiries, please ping mupuf on IRC (#nouveau, freenode). + +Bug reports should be filled on Freedesktop's bug tracker. Please follow +http://nouveau.freedesktop.org/wiki/Bugs |