14 files changed, 260 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt b/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt
new file mode 100644
index 00000000000..f93242be60a
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt
@@ -0,0 +1,23 @@
+IBM POWERNV platform sensors
+----------------------------
+
+Required node properties:
+- compatible: must be one of
+		"ibm,opal-sensor-cooling-fan"
+		"ibm,opal-sensor-amb-temp"
+		"ibm,opal-sensor-power-supply"
+		"ibm,opal-sensor-power"
+- sensor-id: an opaque id provided by the firmware to the kernel, identifies a
+	     given sensor and its attribute data
+
+Example sensors node:
+
+cooling-fan#8-data {
+	sensor-id = <0x7052107>;
+	compatible = "ibm,opal-sensor-cooling-fan";
+};
+
+amb-temp#1-thrs {
+	sensor-id = <0x5096000>;
+	compatible = "ibm,opal-sensor-amb-temp";
+};
diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt
index b117b2e9e1a..2391e5c4199 100644
--- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt
+++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt
@@ -3,6 +3,7 @@ NTC Thermistor hwmon sensors
 
 Requires node properties:
 - "compatible" value : one of
+	"epcos,b57330v2103"
 	"murata,ncp15wb473"
 	"murata,ncp18wb473"
 	"murata,ncp21wb473"
diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt
new file mode 100644
index 00000000000..610757ce449
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt
@@ -0,0 +1,12 @@
+Bindings for a fan connected to the PWM lines
+
+Required properties:
+- compatible	: "pwm-fan"
+- pwms		: the PWM that is used to control the PWM fan
+
+Example:
+	pwm-fan {
+		compatible = "pwm-fan";
+		status = "okay";
+		pwms = <&pwm 0 10000 0>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 1a794213f7d..37803eb5521 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -84,5 +84,6 @@ stm,m41t80		M41T80 - SERIAL ACCESS RTC WITH ALARMS
 taos,tsl2550		Ambient Light Sensor with SMBUS/Two Wire Serial Interface
 ti,tsc2003		I2C Touch-Screen Controller
 ti,tmp102		Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface
+ti,tmp103		Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface
 ti,tmp275		Digital Temperature Sensor
 winbond,wpct301		i2c trusted platform module (TPM)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 46a311e728a..97c9c06132c 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -42,6 +42,7 @@ dmo	Data Modul AG
 ebv	EBV Elektronik
 edt	Emerging Display Technologies
 emmicro	EM Microelectronic
+epcos	EPCOS AG
 epfl	Ecole Polytechnique Fédérale de Lausanne
 epson	Seiko Epson Corp.
 est	ESTeem Wireless Modems
diff --git a/Documentation/hwmon/ibmpowernv b/Documentation/hwmon/ibmpowernv
new file mode 100644
index 00000000000..8826ba29db3
--- /dev/null
+++ b/Documentation/hwmon/ibmpowernv
@@ -0,0 +1,41 @@
+Kernel Driver IBMPOWERNV
+========================
+
+Supported systems:
+  * Any recent IBM P servers based on POWERNV platform
+
+Author: Neelesh Gupta
+
+Description
+-----------
+
+This driver implements reading the platform sensors data like temperature/fan/
+voltage/power for 'POWERNV' platform.
+
+The driver uses the platform device infrastructure. It probes the device tree
+for sensor devices during the __init phase and registers them with the 'hwmon'.
+'hwmon' populates the 'sysfs' tree having attribute files, each for a given
+sensor type and its attribute data.
+
+All the nodes in the DT appear under "/ibm,opal/sensors" and each valid node in
+the DT maps to an attribute file in 'sysfs'. The node exports unique 'sensor-id'
+which the driver uses to make an OPAL call to the firmware.
+
+Usage notes
+-----------
+The driver is built statically with the kernel by enabling the config
+CONFIG_SENSORS_IBMPOWERNV. It can also be built as module 'ibmpowernv'.
+
+Sysfs attributes
+----------------
+
+fanX_input		Measured RPM value.
+fanX_min		Threshold RPM for alert generation.
+fanX_fault		0: No fail condition
+			1: Failing fan
+tempX_input		Measured ambient temperature.
+tempX_max		Threshold ambient temperature for alert generation.
+inX_input		Measured power supply voltage
+inX_fault		0: No fail condition.
+			1: Failing power supply.
+power1_input		System power consumption (microWatt)
diff --git a/Documentation/hwmon/lm75 b/Documentation/hwmon/lm75
index 2560a9c6d44..c6a5ff1b464 100644
--- a/Documentation/hwmon/lm75
+++ b/Documentation/hwmon/lm75
@@ -42,13 +42,14 @@ Supported chips:
     Addresses scanned: none
     Datasheet: Publicly available at the ST website
                http://www.st.com/internet/analog/product/121769.jsp
-  * Texas Instruments TMP100, TMP101, TMP105, TMP75, TMP175, TMP275
-    Prefixes: 'tmp100', 'tmp101', 'tmp105', 'tmp175', 'tmp75', 'tmp275'
+  * Texas Instruments TMP100, TMP101, TMP105, TMP112, TMP75, TMP175, TMP275
+    Prefixes: 'tmp100', 'tmp101', 'tmp105', 'tmp112', 'tmp175', 'tmp75', 'tmp275'
     Addresses scanned: none
     Datasheet: Publicly available at the Texas Instruments website
                http://www.ti.com/product/tmp100
                http://www.ti.com/product/tmp101
                http://www.ti.com/product/tmp105
+               http://www.ti.com/product/tmp112
                http://www.ti.com/product/tmp75
                http://www.ti.com/product/tmp175
                http://www.ti.com/product/tmp275
diff --git a/Documentation/hwmon/ntc_thermistor b/Documentation/hwmon/ntc_thermistor
index 057b77029f2..c5e05e2900a 100644
--- a/Documentation/hwmon/ntc_thermistor
+++ b/Documentation/hwmon/ntc_thermistor
@@ -6,6 +6,11 @@ Supported thermistors from Murata:
   Prefixes: 'ncp15wb473', 'ncp18wb473', 'ncp21wb473', 'ncp03wb473', 'ncp15wl333'
   Datasheet: Publicly available at Murata
 
+Supported thermistors from EPCOS:
+* EPCOS NTC Thermistors B57330V2103
+  Prefixes: b57330v2103
+  Datasheet: Publicly available at EPCOS
+
 Other NTC thermistors can be supported simply by adding compensation
 tables; e.g., NCP15WL333 support is added by the table ncpXXwl333.
 
diff --git a/Documentation/hwmon/pmbus b/Documentation/hwmon/pmbus
index cf756ed48ff..a3557da8f5b 100644
--- a/Documentation/hwmon/pmbus
+++ b/Documentation/hwmon/pmbus
@@ -23,12 +23,11 @@ Supported chips:
 	http://www.lineagepower.com/oem/pdf/PDT012A0X.pdf
 	http://www.lineagepower.com/oem/pdf/UDT020A0X.pdf
 	http://www.lineagepower.com/oem/pdf/MDT040A0X.pdf
-  * Texas Instruments TPS40400, TPS40422
-    Prefixes: 'tps40400', 'tps40422'
+  * Texas Instruments TPS40400
+    Prefixes: 'tps40400'
     Addresses scanned: -
     Datasheets:
 	http://www.ti.com/lit/gpn/tps40400
-	http://www.ti.com/lit/gpn/tps40422
   * Generic PMBus devices
     Prefix: 'pmbus'
     Addresses scanned: -
diff --git a/Documentation/hwmon/powr1220 b/Documentation/hwmon/powr1220
new file mode 100644
index 00000000000..21e44f71ae6
--- /dev/null
+++ b/Documentation/hwmon/powr1220
@@ -0,0 +1,45 @@
+Kernel driver powr1220
+==================
+
+Supported chips:
+  * Lattice POWR1220AT8
+    Prefix: 'powr1220'
+    Addresses scanned: none
+    Datasheet: Publicly available at the Lattice website
+               http://www.latticesemi.com/
+
+Author: Scott Kanowitz <scott.kanowitz@gmail.com>
+
+Description
+-----------
+
+This driver supports the Lattice POWR1220AT8 chip. The POWR1220
+includes voltage monitoring for 14 inputs as well as trim settings
+for output voltages and GPIOs. This driver implements the voltage
+monitoring portion of the chip.
+
+Voltages are sampled by a 12-bit ADC with a step size of 2 mV.
+An in-line attenuator allows measurements from 0 to 6 V. The
+attenuator is enabled or disabled depending on the setting of the
+input's max value. The driver will enable the attenuator for any
+value over the low measurement range maximum of 2 V.
+
+The input naming convention is as follows:
+
+driver name    pin name
+in0            VMON1
+in1            VMON2
+in2            VMON3
+in2            VMON4
+in4            VMON5
+in5            VMON6
+in6            VMON7
+in7            VMON8
+in8            VMON9
+in9            VMON10
+in10           VMON11
+in11           VMON12
+in12           VCCA
+in13           VCCINP
+
+The ADC readings are updated on request with a minimum period of 1s.
diff --git a/Documentation/hwmon/pwm-fan b/Documentation/hwmon/pwm-fan
new file mode 100644
index 00000000000..18529d2e3bc
--- /dev/null
+++ b/Documentation/hwmon/pwm-fan
@@ -0,0 +1,17 @@
+Kernel driver pwm-fan
+=====================
+
+This driver enables the use of a PWM module to drive a fan. It uses the
+generic PWM interface thus it is hardware independent. It can be used on
+many SoCs, as long as the SoC supplies a PWM line driver that exposes
+the generic PWM API.
+
+Author: Kamil Debski <k.debski@samsung.com>
+
+Description
+-----------
+
+The driver implements a simple interface for driving a fan connected to
+a PWM output. It uses the generic PWM interface, thus it can be used with
+a range of SoCs. The driver exposes the fan to the user space through
+the hwmon's sysfs interface.
diff --git a/Documentation/hwmon/tmp103 b/Documentation/hwmon/tmp103
new file mode 100644
index 00000000000..ec00a15645b
--- /dev/null
+++ b/Documentation/hwmon/tmp103
@@ -0,0 +1,28 @@
+Kernel driver tmp103
+====================
+
+Supported chips:
+  * Texas Instruments TMP103
+    Prefix: 'tmp103'
+    Addresses scanned: none
+    Product info and datasheet: http://www.ti.com/product/tmp103
+
+Author:
+	Heiko Schocher <hs@denx.de>
+
+Description
+-----------
+
+The TMP103 is a digital output temperature sensor in a four-ball
+wafer chip-scale package (WCSP). The TMP103 is capable of reading
+temperatures to a resolution of 1°C. The TMP103 is specified for
+operation over a temperature range of –40°C to +125°C.
+
+Resolution: 8 Bits
+Accuracy: ±1°C Typ (–10°C to +100°C)
+
+The driver provides the common sysfs-interface for temperatures (see
+Documentation/hwmon/sysfs-interface under Temperatures).
+
+Please refer how to instantiate this driver:
+Documentation/i2c/instantiating-devices
diff --git a/Documentation/hwmon/tmp421 b/Documentation/hwmon/tmp421
index 0cf07f82474..9e6fe5549ca 100644
--- a/Documentation/hwmon/tmp421
+++ b/Documentation/hwmon/tmp421
@@ -8,12 +8,20 @@ Supported chips:
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
   * Texas Instruments TMP422
     Prefix: 'tmp422'
-    Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+    Addresses scanned: I2C 0x4c, 0x4d, 0x4e and 0x4f
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
   * Texas Instruments TMP423
     Prefix: 'tmp423'
-    Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+    Addresses scanned: I2C 0x4c and 0x4d
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+  * Texas Instruments TMP441
+    Prefix: 'tmp441'
+    Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+    Datasheet: http://www.ti.com/product/tmp441
+  * Texas Instruments TMP442
+    Prefix: 'tmp442'
+    Addresses scanned: I2C 0x4c and 0x4d
+    Datasheet: http://www.ti.com/product/tmp442
 
 Authors:
 	Andre Prendel <andre.prendel@gmx.de>
@@ -21,13 +29,13 @@ Authors:
 Description
 -----------
 
-This driver implements support for Texas Instruments TMP421, TMP422
-and TMP423 temperature sensor chips. These chips implement one local
-and up to one (TMP421), up to two (TMP422) or up to three (TMP423)
-remote sensors. Temperature is measured in degrees Celsius. The chips
-are wired over I2C/SMBus and specified over a temperature range of -40
-to +125 degrees Celsius. Resolution for both the local and remote
-channels is 0.0625 degree C.
+This driver implements support for Texas Instruments TMP421, TMP422,
+TMP423, TMP441, and TMP442 temperature sensor chips. These chips
+implement one local and up to one (TMP421, TMP441), up to two (TMP422,
+TMP442) or up to three (TMP423) remote sensors. Temperature is measured
+in degrees Celsius. The chips are wired over I2C/SMBus and specified
+over a temperature range of -40 to +125 degrees Celsius. Resolution
+for both the local and remote channels is 0.0625 degree C.
 
 The chips support only temperature measurement. The driver exports
 the temperature values via the following sysfs files:
diff --git a/Documentation/hwmon/tps40422 b/Documentation/hwmon/tps40422
new file mode 100644
index 00000000000..24bb0688d51
--- /dev/null
+++ b/Documentation/hwmon/tps40422
@@ -0,0 +1,64 @@
+Kernel driver tps40422
+======================
+
+Supported chips:
+  * TI TPS40422
+    Prefix: 'tps40422'
+    Addresses scanned: -
+    Datasheet: http://www.ti.com/lit/gpn/tps40422
+
+Author: Zhu Laiwen <richard.zhu@nsn.com>
+
+
+Description
+-----------
+
+This driver supports TI TPS40422 Dual-Output or Two-Phase Synchronous Buck
+Controller with PMBus
+
+The driver is a client driver to the core PMBus driver.
+Please see Documentation/hwmon/pmbus for details on PMBus client drivers.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+
+Platform data support
+---------------------
+
+The driver supports standard PMBus driver platform data.
+
+
+Sysfs entries
+-------------
+
+The following attributes are supported.
+
+in[1-2]_label		"vout[1-2]"
+in[1-2]_input		Measured voltage. From READ_VOUT register.
+in[1-2]_alarm		voltage alarm.
+
+curr[1-2]_input		Measured current. From READ_IOUT register.
+curr[1-2]_label		"iout[1-2]"
+curr1_max		Maximum current. From IOUT_OC_WARN_LIMIT register.
+curr1_crit		Critical maximum current. From IOUT_OC_FAULT_LIMIT register.
+curr1_max_alarm		Current high alarm. From IOUT_OC_WARN_LIMIT status.
+curr1_crit_alarm	Current critical high alarm. From IOUT_OC_FAULT status.
+curr2_alarm		Current high alarm. From IOUT_OC_WARNING status.
+
+temp1_input		Measured temperature. From READ_TEMPERATURE_2 register on page 0.
+temp1_max		Maximum temperature. From OT_WARN_LIMIT register.
+temp1_crit		Critical high temperature. From OT_FAULT_LIMIT register.
+temp1_max_alarm		Chip temperature high alarm. Set by comparing
+			READ_TEMPERATURE_2 on page 0 with OT_WARN_LIMIT if TEMP_OT_WARNING
+			status is set.
+temp1_crit_alarm	Chip temperature critical high alarm. Set by comparing
+			READ_TEMPERATURE_2 on page 0 with OT_FAULT_LIMIT if TEMP_OT_FAULT
+			status is set.
+temp2_input		Measured temperature. From READ_TEMPERATURE_2 register on page 1.
+temp2_alarm		Chip temperature alarm on page 1.