diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-pci | 12 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-tty | 9 | ||||
| -rw-r--r-- | Documentation/block/00-INDEX | 10 | ||||
| -rw-r--r-- | Documentation/block/cfq-iosched.txt | 77 | ||||
| -rw-r--r-- | Documentation/block/queue-sysfs.txt | 64 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt | 8 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt | 14 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/tty/serial/of-serial.txt | 2 | ||||
| -rw-r--r-- | Documentation/feature-removal-schedule.txt | 2 | ||||
| -rw-r--r-- | Documentation/serial/00-INDEX | 2 | ||||
| -rw-r--r-- | Documentation/serial/computone.txt | 520 | ||||
| -rw-r--r-- | Documentation/watchdog/src/watchdog-test.c | 2 |
12 files changed, 192 insertions, 530 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-pci b/Documentation/ABI/testing/sysfs-bus-pci index 34f51100f02..dff1f48d252 100644 --- a/Documentation/ABI/testing/sysfs-bus-pci +++ b/Documentation/ABI/testing/sysfs-bus-pci @@ -210,3 +210,15 @@ Users: firmware assigned instance number of the PCI device that can help in understanding the firmware intended order of the PCI device. + +What: /sys/bus/pci/devices/.../d3cold_allowed +Date: July 2012 +Contact: Huang Ying <ying.huang@intel.com> +Description: + d3cold_allowed is bit to control whether the corresponding PCI + device can be put into D3Cold state. If it is cleared, the + device will never be put into D3Cold state. If it is set, the + device may be put into D3Cold state if other requirements are + satisfied too. Reading this attribute will show the current + value of d3cold_allowed bit. Writing this attribute will set + the value of d3cold_allowed bit. diff --git a/Documentation/ABI/testing/sysfs-tty b/Documentation/ABI/testing/sysfs-tty index b138b663bf5..0c430150d92 100644 --- a/Documentation/ABI/testing/sysfs-tty +++ b/Documentation/ABI/testing/sysfs-tty @@ -17,3 +17,12 @@ Description: device, like 'tty1'. The file supports poll() to detect virtual console switches. + +What: /sys/class/tty/ttyS0/uartclk +Date: Sep 2012 +Contact: Tomas Hlavacek <tmshlvck@gmail.com> +Description: + Shows the current uartclk value associated with the + UART port in serial_core, that is bound to TTY like ttyS0. + uartclk = 16 * baud_base + diff --git a/Documentation/block/00-INDEX b/Documentation/block/00-INDEX index d111e3b23db..d18ecd827c4 100644 --- a/Documentation/block/00-INDEX +++ b/Documentation/block/00-INDEX @@ -3,15 +3,21 @@ biodoc.txt - Notes on the Generic Block Layer Rewrite in Linux 2.5 capability.txt - - Generic Block Device Capability (/sys/block/<disk>/capability) + - Generic Block Device Capability (/sys/block/<device>/capability) +cfq-iosched.txt + - CFQ IO scheduler tunables +data-integrity.txt + - Block data integrity deadline-iosched.txt - Deadline IO scheduler tunables ioprio.txt - Block io priorities (in CFQ scheduler) +queue-sysfs.txt + - Queue's sysfs entries request.txt - The members of struct request (in include/linux/blkdev.h) stat.txt - - Block layer statistics in /sys/block/<dev>/stat + - Block layer statistics in /sys/block/<device>/stat switching-sched.txt - Switching I/O schedulers at runtime writeback_cache_control.txt diff --git a/Documentation/block/cfq-iosched.txt b/Documentation/block/cfq-iosched.txt index 6d670f57045..d89b4fe724d 100644 --- a/Documentation/block/cfq-iosched.txt +++ b/Documentation/block/cfq-iosched.txt @@ -1,3 +1,14 @@ +CFQ (Complete Fairness Queueing) +=============================== + +The main aim of CFQ scheduler is to provide a fair allocation of the disk +I/O bandwidth for all the processes which requests an I/O operation. + +CFQ maintains the per process queue for the processes which request I/O +operation(syncronous requests). In case of asynchronous requests, all the +requests from all the processes are batched together according to their +process's I/O priority. + CFQ ioscheduler tunables ======================== @@ -25,6 +36,72 @@ there are multiple spindles behind single LUN (Host based hardware RAID controller or for storage arrays), setting slice_idle=0 might end up in better throughput and acceptable latencies. +back_seek_max +------------- +This specifies, given in Kbytes, the maximum "distance" for backward seeking. +The distance is the amount of space from the current head location to the +sectors that are backward in terms of distance. + +This parameter allows the scheduler to anticipate requests in the "backward" +direction and consider them as being the "next" if they are within this +distance from the current head location. + +back_seek_penalty +----------------- +This parameter is used to compute the cost of backward seeking. If the +backward distance of request is just 1/back_seek_penalty from a "front" +request, then the seeking cost of two requests is considered equivalent. + +So scheduler will not bias toward one or the other request (otherwise scheduler +will bias toward front request). Default value of back_seek_penalty is 2. + +fifo_expire_async +----------------- +This parameter is used to set the timeout of asynchronous requests. Default +value of this is 248ms. + +fifo_expire_sync +---------------- +This parameter is used to set the timeout of synchronous requests. Default +value of this is 124ms. In case to favor synchronous requests over asynchronous +one, this value should be decreased relative to fifo_expire_async. + +slice_async +----------- +This parameter is same as of slice_sync but for asynchronous queue. The +default value is 40ms. + +slice_async_rq +-------------- +This parameter is used to limit the dispatching of asynchronous request to +device request queue in queue's slice time. The maximum number of request that +are allowed to be dispatched also depends upon the io priority. Default value +for this is 2. + +slice_sync +---------- +When a queue is selected for execution, the queues IO requests are only +executed for a certain amount of time(time_slice) before switching to another +queue. This parameter is used to calculate the time slice of synchronous +queue. + +time_slice is computed using the below equation:- +time_slice = slice_sync + (slice_sync/5 * (4 - prio)). To increase the +time_slice of synchronous queue, increase the value of slice_sync. Default +value is 100ms. + +quantum +------- +This specifies the number of request dispatched to the device queue. In a +queue's time slice, a request will not be dispatched if the number of request +in the device exceeds this parameter. This parameter is used for synchronous +request. + +In case of storage with several disk, this setting can limit the parallel +processing of request. Therefore, increasing the value can imporve the +performace although this can cause the latency of some I/O to increase due +to more number of requests. + CFQ IOPS Mode for group scheduling =================================== Basic CFQ design is to provide priority based time slices. Higher priority diff --git a/Documentation/block/queue-sysfs.txt b/Documentation/block/queue-sysfs.txt index 6518a55273e..e54ac1d5340 100644 --- a/Documentation/block/queue-sysfs.txt +++ b/Documentation/block/queue-sysfs.txt @@ -9,20 +9,71 @@ These files are the ones found in the /sys/block/xxx/queue/ directory. Files denoted with a RO postfix are readonly and the RW postfix means read-write. +add_random (RW) +---------------- +This file allows to trun off the disk entropy contribution. Default +value of this file is '1'(on). + +discard_granularity (RO) +----------------------- +This shows the size of internal allocation of the device in bytes, if +reported by the device. A value of '0' means device does not support +the discard functionality. + +discard_max_bytes (RO) +---------------------- +Devices that support discard functionality may have internal limits on +the number of bytes that can be trimmed or unmapped in a single operation. +The discard_max_bytes parameter is set by the device driver to the maximum +number of bytes that can be discarded in a single operation. Discard +requests issued to the device must not exceed this limit. A discard_max_bytes +value of 0 means that the device does not support discard functionality. + +discard_zeroes_data (RO) +------------------------ +When read, this file will show if the discarded block are zeroed by the +device or not. If its value is '1' the blocks are zeroed otherwise not. + hw_sector_size (RO) ------------------- This is the hardware sector size of the device, in bytes. +iostats (RW) +------------- +This file is used to control (on/off) the iostats accounting of the +disk. + +logical_block_size (RO) +----------------------- +This is the logcal block size of the device, in bytes. + max_hw_sectors_kb (RO) ---------------------- This is the maximum number of kilobytes supported in a single data transfer. +max_integrity_segments (RO) +--------------------------- +When read, this file shows the max limit of integrity segments as +set by block layer which a hardware controller can handle. + max_sectors_kb (RW) ------------------- This is the maximum number of kilobytes that the block layer will allow for a filesystem request. Must be smaller than or equal to the maximum size allowed by the hardware. +max_segments (RO) +----------------- +Maximum number of segments of the device. + +max_segment_size (RO) +--------------------- +Maximum segment size of the device. + +minimum_io_size (RO) +-------------------- +This is the smallest preferred io size reported by the device. + nomerges (RW) ------------- This enables the user to disable the lookup logic involved with IO @@ -45,11 +96,24 @@ per-block-cgroup request pool. IOW, if there are N block cgroups, each request queue may have upto N request pools, each independently regulated by nr_requests. +optimal_io_size (RO) +-------------------- +This is the optimal io size reported by the device. + +physical_block_size (RO) +------------------------ +This is the physical block size of device, in bytes. + read_ahead_kb (RW) ------------------ Maximum number of kilobytes to read-ahead for filesystems on this block device. +rotational (RW) +--------------- +This file is used to stat if the device is of rotational type or +non-rotational type. + rq_affinity (RW) ---------------- If this option is '1', the block layer will migrate request completions to the diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 70cd49b1caa..1dd622546d0 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -10,8 +10,8 @@ Required properties: - compatible : Should be "fsl,<chip>-esdhc" Optional properties: -- fsl,cd-internal : Indicate to use controller internal card detection -- fsl,wp-internal : Indicate to use controller internal write protection +- fsl,cd-controller : Indicate to use controller internal card detection +- fsl,wp-controller : Indicate to use controller internal write protection Examples: @@ -19,8 +19,8 @@ esdhc@70004000 { compatible = "fsl,imx51-esdhc"; reg = <0x70004000 0x4000>; interrupts = <1>; - fsl,cd-internal; - fsl,wp-internal; + fsl,cd-controller; + fsl,wp-controller; }; esdhc@70008000 { diff --git a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt new file mode 100644 index 00000000000..0d439dfc1aa --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt @@ -0,0 +1,14 @@ +* NXP LPC32xx SoC High Speed UART + +Required properties: +- compatible: Should be "nxp,lpc3220-hsuart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt + +Example: + + uart1: serial@40014000 { + compatible = "nxp,lpc3220-hsuart"; + reg = <0x40014000 0x1000>; + interrupts = <26 0>; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt index 0847fdeee11..ba385f2e0dd 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -25,6 +25,8 @@ Optional properties: accesses to the UART (e.g. TI davinci). - used-by-rtas : set to indicate that the port is in use by the OpenFirmware RTAS and should not be registered. +- no-loopback-test: set to indicate that the port does not implements loopback + test mode Example: diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index afaff312bf4..f4d8c7105fc 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -579,7 +579,7 @@ Why: KVM tracepoints provide mostly equivalent information in a much more ---------------------------- What: at91-mci driver ("CONFIG_MMC_AT91") -When: 3.7 +When: 3.8 Why: There are two mci drivers: at91-mci and atmel-mci. The PDC support was added to atmel-mci as a first step to support more chips. Then at91-mci was kept only for old IP versions (on at91rm9200 and diff --git a/Documentation/serial/00-INDEX b/Documentation/serial/00-INDEX index e09468ad3cb..f7b0c7dc25e 100644 --- a/Documentation/serial/00-INDEX +++ b/Documentation/serial/00-INDEX @@ -2,8 +2,6 @@ - this file. README.cycladesZ - info on Cyclades-Z firmware loading. -computone.txt - - info on Computone Intelliport II/Plus Multiport Serial Driver. digiepca.txt - info on Digi Intl. {PC,PCI,EISA}Xx and Xem series cards. hayes-esp.txt diff --git a/Documentation/serial/computone.txt b/Documentation/serial/computone.txt deleted file mode 100644 index a6a1158ea2b..00000000000 --- a/Documentation/serial/computone.txt +++ /dev/null @@ -1,520 +0,0 @@ -NOTE: This is an unmaintained driver. It is not guaranteed to work due to -changes made in the tty layer in 2.6. If you wish to take over maintenance of -this driver, contact Michael Warfield <mhw@wittsend.com>. - -Changelog: ----------- -11-01-2001: Original Document - -10-29-2004: Minor misspelling & format fix, update status of driver. - James Nelson <james4765@gmail.com> - -Computone Intelliport II/Plus Multiport Serial Driver ------------------------------------------------------ - -Release Notes For Linux Kernel 2.2 and higher. -These notes are for the drivers which have already been integrated into the -kernel and have been tested on Linux kernels 2.0, 2.2, 2.3, and 2.4. - -Version: 1.2.14 -Date: 11/01/2001 -Historical Author: Andrew Manison <amanison@america.net> -Primary Author: Doug McNash - -This file assumes that you are using the Computone drivers which are -integrated into the kernel sources. For updating the drivers or installing -drivers into kernels which do not already have Computone drivers, please -refer to the instructions in the README.computone file in the driver patch. - - -1. INTRODUCTION - -This driver supports the entire family of Intelliport II/Plus controllers -with the exception of the MicroChannel controllers. It does not support -products previous to the Intelliport II. - -This driver was developed on the v2.0.x Linux tree and has been tested up -to v2.4.14; it will probably not work with earlier v1.X kernels,. - - -2. QUICK INSTALLATION - -Hardware - If you have an ISA card, find a free interrupt and io port. - List those in use with `cat /proc/interrupts` and - `cat /proc/ioports`. Set the card dip switches to a free - address. You may need to configure your BIOS to reserve an - irq for an ISA card. PCI and EISA parameters are set - automagically. Insert card into computer with the power off - before or after drivers installation. - - Note the hardware address from the Computone ISA cards installed into - the system. These are required for editing ip2.c or editing - /etc/modprobe.d/*.conf, or for specification on the modprobe - command line. - - Note that the /etc/modules.conf should be used for older (pre-2.6) - kernels. - -Software - - -Module installation: - -a) Determine free irq/address to use if any (configure BIOS if need be) -b) Run "make config" or "make menuconfig" or "make xconfig" - Select (m) module for CONFIG_COMPUTONE under character - devices. CONFIG_PCI and CONFIG_MODULES also may need to be set. -c) Set address on ISA cards then: - edit /usr/src/linux/drivers/char/ip2.c if needed - or - edit config file in /etc/modprobe.d/ if needed (module). - or both to match this setting. -d) Run "make modules" -e) Run "make modules_install" -f) Run "/sbin/depmod -a" -g) install driver using `modprobe ip2 <options>` (options listed below) -h) run ip2mkdev (either the script below or the binary version) - - -Kernel installation: - -a) Determine free irq/address to use if any (configure BIOS if need be) -b) Run "make config" or "make menuconfig" or "make xconfig" - Select (y) kernel for CONFIG_COMPUTONE under character - devices. CONFIG_PCI may need to be set if you have PCI bus. -c) Set address on ISA cards then: - edit /usr/src/linux/drivers/char/ip2.c - (Optional - may be specified on kernel command line now) -d) Run "make zImage" or whatever target you prefer. -e) mv /usr/src/linux/arch/x86/boot/zImage to /boot. -f) Add new config for this kernel into /etc/lilo.conf, run "lilo" - or copy to a floppy disk and boot from that floppy disk. -g) Reboot using this kernel -h) run ip2mkdev (either the script below or the binary version) - -Kernel command line options: - -When compiling the driver into the kernel, io and irq may be -compiled into the driver by editing ip2.c and setting the values for -io and irq in the appropriate array. An alternative is to specify -a command line parameter to the kernel at boot up. - - ip2=io0,irq0,io1,irq1,io2,irq2,io3,irq3 - -Note that this order is very different from the specifications for the -modload parameters which have separate IRQ and IO specifiers. - -The io port also selects PCI (1) and EISA (2) boards. - - io=0 No board - io=1 PCI board - io=2 EISA board - else ISA board io address - -You only need to specify the boards which are present. - - Examples: - - 2 PCI boards: - - ip2=1,0,1,0 - - 1 ISA board at 0x310 irq 5: - - ip2=0x310,5 - -This can be added to and "append" option in lilo.conf similar to this: - - append="ip2=1,0,1,0" - - -3. INSTALLATION - -Previously, the driver sources were packaged with a set of patch files -to update the character drivers' makefile and configuration file, and other -kernel source files. A build script (ip2build) was included which applies -the patches if needed, and build any utilities needed. -What you receive may be a single patch file in conventional kernel -patch format build script. That form can also be applied by -running patch -p1 < ThePatchFile. Otherwise run ip2build. - -The driver can be installed as a module (recommended) or built into the -kernel. This is selected as for other drivers through the `make config` -command from the root of the Linux source tree. If the driver is built -into the kernel you will need to edit the file ip2.c to match the boards -you are installing. See that file for instructions. If the driver is -installed as a module the configuration can also be specified on the -modprobe command line as follows: - - modprobe ip2 irq=irq1,irq2,irq3,irq4 io=addr1,addr2,addr3,addr4 - -where irqnum is one of the valid Intelliport II interrupts (3,4,5,7,10,11, -12,15) and addr1-4 are the base addresses for up to four controllers. If -the irqs are not specified the driver uses the default in ip2.c (which -selects polled mode). If no base addresses are specified the defaults in -ip2.c are used. If you are autoloading the driver module with kerneld or -kmod the base addresses and interrupt number must also be set in ip2.c -and recompile or just insert and options line in /etc/modprobe.d/*.conf or both. -The options line is equivalent to the command line and takes precedence over -what is in ip2.c. - -config sample to put /etc/modprobe.d/*.conf: - options ip2 io=1,0x328 irq=1,10 - alias char-major-71 ip2 - alias char-major-72 ip2 - alias char-major-73 ip2 - -The equivalent in ip2.c: - -static int io[IP2_MAX_BOARDS]= { 1, 0x328, 0, 0 }; -static int irq[IP2_MAX_BOARDS] = { 1, 10, -1, -1 }; - -The equivalent for the kernel command line (in lilo.conf): - - append="ip2=1,1,0x328,10" - - -Note: Both io and irq should be updated to reflect YOUR system. An "io" - address of 1 or 2 indicates a PCI or EISA card in the board table. - The PCI or EISA irq will be assigned automatically. - -Specifying an invalid or in-use irq will default the driver into -running in polled mode for that card. If all irq entries are 0 then -all cards will operate in polled mode. - -If you select the driver as part of the kernel run : - - make zlilo (or whatever you do to create a bootable kernel) - -If you selected a module run : - - make modules && make modules_install - -The utility ip2mkdev (see 5 and 7 below) creates all the device nodes -required by the driver. For a device to be created it must be configured -in the driver and the board must be installed. Only devices corresponding -to real IntelliPort II ports are created. With multiple boards and expansion -boxes this will leave gaps in the sequence of device names. ip2mkdev uses -Linux tty naming conventions: ttyF0 - ttyF255 for normal devices, and -cuf0 - cuf255 for callout devices. - - -4. USING THE DRIVERS - -As noted above, the driver implements the ports in accordance with Linux -conventions, and the devices should be interchangeable with the standard -serial devices. (This is a key point for problem reporting: please make -sure that what you are trying do works on the ttySx/cuax ports first; then -tell us what went wrong with the ip2 ports!) - -Higher speeds can be obtained using the setserial utility which remaps -38,400 bps (extb) to 57,600 bps, 115,200 bps, or a custom speed. -Intelliport II installations using the PowerPort expansion module can -use the custom speed setting to select the highest speeds: 153,600 bps, -230,400 bps, 307,200 bps, 460,800bps and 921,600 bps. The base for -custom baud rate configuration is fixed at 921,600 for cards/expansion -modules with ST654's and 115200 for those with Cirrus CD1400's. This -corresponds to the maximum bit rates those chips are capable. -For example if the baud base is 921600 and the baud divisor is 18 then -the custom rate is 921600/18 = 51200 bps. See the setserial man page for -complete details. Of course if stty accepts the higher rates now you can -use that as well as the standard ioctls(). - - -5. ip2mkdev and assorted utilities... - -Several utilities, including the source for a binary ip2mkdev utility are -available under .../drivers/char/ip2. These can be build by changing to -that directory and typing "make" after the kernel has be built. If you do -not wish to compile the binary utilities, the shell script below can be -cut out and run as "ip2mkdev" to create the necessary device files. To -use the ip2mkdev script, you must have procfs enabled and the proc file -system mounted on /proc. - - -6. NOTES - -This is a release version of the driver, but it is impossible to test it -in all configurations of Linux. If there is any anomalous behaviour that -does not match the standard serial port's behaviour please let us know. - - -7. ip2mkdev shell script - -Previously, this script was simply attached here. It is now attached as a -shar archive to make it easier to extract the script from the documentation. -To create the ip2mkdev shell script change to a convenient directory (/tmp -works just fine) and run the following command: - - unshar Documentation/serial/computone.txt - (This file) - -You should now have a file ip2mkdev in your current working directory with -permissions set to execute. Running that script with then create the -necessary devices for the Computone boards, interfaces, and ports which -are present on you system at the time it is run. - - -#!/bin/sh -# This is a shell archive (produced by GNU sharutils 4.2.1). -# To extract the files from this archive, save it to some FILE, remove -# everything before the `!/bin/sh' line above, then type `sh FILE'. -# -# Made on 2001-10-29 10:32 EST by <mhw@alcove.wittsend.com>. -# Source directory was `/home2/src/tmp'. -# -# Existing files will *not* be overwritten unless `-c' is specified. -# -# This shar contains: -# length mode name -# ------ ---------- ------------------------------------------ -# 4251 -rwxr-xr-x ip2mkdev -# -save_IFS="${IFS}" -IFS="${IFS}:" -gettext_dir=FAILED -locale_dir=FAILED -first_param="$1" -for dir in $PATH -do - if test "$gettext_dir" = FAILED && test -f $dir/gettext \ - && ($dir/gettext --version >/dev/null 2>&1) - then - set `$dir/gettext --version 2>&1` - if test "$3" = GNU - then - gettext_dir=$dir - fi - fi - if test "$locale_dir" = FAILED && test -f $dir/shar \ - && ($dir/shar --print-text-domain-dir >/dev/null 2>&1) - then - locale_dir=`$dir/shar --print-text-domain-dir` - fi -done -IFS="$save_IFS" -if test "$locale_dir" = FAILED || test "$gettext_dir" = FAILED -then - echo=echo -else - TEXTDOMAINDIR=$locale_dir - export TEXTDOMAINDIR - TEXTDOMAIN=sharutils - export TEXTDOMAIN - echo="$gettext_dir/gettext -s" -fi -if touch -am -t 200112312359.59 $$.touch >/dev/null 2>&1 && test ! -f 200112312359.59 -a -f $$.touch; then - shar_touch='touch -am -t $1$2$3$4$5$6.$7 "$8"' -elif touch -am 123123592001.59 $$.touch >/dev/null 2>&1 && test ! -f 123123592001.59 -a ! -f 123123592001.5 -a -f $$.touch; then - shar_touch='touch -am $3$4$5$6$1$2.$7 "$8"' -elif touch -am 1231235901 $$.touch >/dev/null 2>&1 && test ! -f 1231235901 -a -f $$.touch; then - shar_touch='touch -am $3$4$5$6$2 "$8"' -else - shar_touch=: - echo - $echo 'WARNING: not restoring timestamps. Consider getting and' - $echo "installing GNU \`touch', distributed in GNU File Utilities..." - echo -fi -rm -f 200112312359.59 123123592001.59 123123592001.5 1231235901 $$.touch -# -if mkdir _sh17581; then - $echo 'x -' 'creating lock directory' -else - $echo 'failed to create lock directory' - exit 1 -fi -# ============= ip2mkdev ============== -if test -f 'ip2mkdev' && test "$first_param" != -c; then - $echo 'x -' SKIPPING 'ip2mkdev' '(file already exists)' -else - $echo 'x -' extracting 'ip2mkdev' '(text)' - sed 's/^X//' << 'SHAR_EOF' > 'ip2mkdev' && -#!/bin/sh - -# -# ip2mkdev -# -# Make or remove devices as needed for Computone Intelliport drivers -# -# First rule! If the dev file exists and you need it, don't mess -# with it. That prevents us from screwing up open ttys, ownership -# and permissions on a running system! -# -# This script will NOT remove devices that no longer exist if their -# board or interface box has been removed. If you want to get rid -# of them, you can manually do an "rm -f /dev/ttyF* /dev/cuaf*" -# before running this script. Running this script will then recreate -# all the valid devices. -# -# Michael H. Warfield -# /\/\|=mhw=|\/\/ -# mhw@wittsend.com -# -# Updated 10/29/2000 for version 1.2.13 naming convention -# under devfs. /\/\|=mhw=|\/\/ -# -# Updated 03/09/2000 for devfs support in ip2 drivers. /\/\|=mhw=|\/\/ -# -X -if test -d /dev/ip2 ; then -# This is devfs mode... We don't do anything except create symlinks -# from the real devices to the old names! -X cd /dev -X echo "Creating symbolic links to devfs devices" -X for i in `ls ip2` ; do -X if test ! -L ip2$i ; then -X # Remove it incase it wasn't a symlink (old device) -X rm -f ip2$i -X ln -s ip2/$i ip2$i -X fi -X done -X for i in `( cd tts ; ls F* )` ; do -X if test ! -L tty$i ; then -X # Remove it incase it wasn't a symlink (old device) -X rm -f tty$i -X ln -s tts/$i tty$i -X fi -X done -X for i in `( cd cua ; ls F* )` ; do -X DEVNUMBER=`expr $i : 'F\(.*\)'` -X if test ! -L cuf$DEVNUMBER ; then -X # Remove it incase it wasn't a symlink (old device) -X rm -f cuf$DEVNUMBER -X ln -s cua/$i cuf$DEVNUMBER -X fi -X done -X exit 0 -fi -X -if test ! -f /proc/tty/drivers -then -X echo "\ -Unable to check driver status. -Make sure proc file system is mounted." -X -X exit 255 -fi -X -if test ! -f /proc/tty/driver/ip2 -then -X echo "\ -Unable to locate ip2 proc file. -Attempting to load driver" -X -X if /sbin/insmod ip2 -X then -X if test ! -f /proc/tty/driver/ip2 -X then -X echo "\ -Unable to locate ip2 proc file after loading driver. -Driver initialization failure or driver version error. -" -X exit 255 -X fi -X else -X echo "Unable to load ip2 driver." -X exit 255 -X fi -fi -X -# Ok... So we got the driver loaded and we can locate the procfs files. -# Next we need our major numbers. -X -TTYMAJOR=`sed -e '/^ip2/!d' -e '/\/dev\/tt/!d' -e 's/.*tt[^ ]*[ ]*\([0-9]*\)[ ]*.*/\1/' < /proc/tty/drivers` -CUAMAJOR=`sed -e '/^ip2/!d' -e '/\/dev\/cu/!d' -e 's/.*cu[^ ]*[ ]*\([0-9]*\)[ ]*.*/\1/' < /proc/tty/drivers` -BRDMAJOR=`sed -e '/^Driver: /!d' -e 's/.*IMajor=\([0-9]*\)[ ]*.*/\1/' < /proc/tty/driver/ip2` -X -echo "\ -TTYMAJOR = $TTYMAJOR -CUAMAJOR = $CUAMAJOR -BRDMAJOR = $BRDMAJOR -" -X -# Ok... Now we should know our major numbers, if appropriate... -# Now we need our boards and start the device loops. -X -grep '^Board [0-9]:' /proc/tty/driver/ip2 | while read token number type alltherest -do -X # The test for blank "type" will catch the stats lead-in lines -X # if they exist in the file -X if test "$type" = "vacant" -o "$type" = "Vacant" -o "$type" = "" -X then -X continue -X fi -X -X BOARDNO=`expr "$number" : '\([0-9]\):'` -X PORTS=`expr "$alltherest" : '.*ports=\([0-9]*\)' | tr ',' ' '` -X MINORS=`expr "$alltherest" : '.*minors=\([0-9,]*\)' | tr ',' ' '` -X -X if test "$BOARDNO" = "" -o "$PORTS" = "" -X then -# This may be a bug. We should at least get this much information -X echo "Unable to process board line" -X continue -X fi -X -X if test "$MINORS" = "" -X then -# Silently skip this one. This board seems to have no boxes -X continue -X fi -X -X echo "board $BOARDNO: $type ports = $PORTS; port numbers = $MINORS" -X -X if test "$BRDMAJOR" != "" -X then -X BRDMINOR=`expr $BOARDNO \* 4` -X STSMINOR=`expr $BRDMINOR + 1` -X if test ! -c /dev/ip2ipl$BOARDNO ; then -X mknod /dev/ip2ipl$BOARDNO c $BRDMAJOR $BRDMINOR -X fi -X if test ! -c /dev/ip2stat$BOARDNO ; then -X mknod /dev/ip2stat$BOARDNO c $BRDMAJOR $STSMINOR -X fi -X fi -X -X if test "$TTYMAJOR" != "" -X then -X PORTNO=$BOARDBASE -X -X for PORTNO in $MINORS -X do -X if test ! -c /dev/ttyF$PORTNO ; then -X # We got the hardware but no device - make it -X mknod /dev/ttyF$PORTNO c $TTYMAJOR $PORTNO -X fi -X done -X fi -X -X if test "$CUAMAJOR" != "" -X then -X PORTNO=$BOARDBASE -X -X for PORTNO in $MINORS -X do -X if test ! -c /dev/cuf$PORTNO ; then -X # We got the hardware but no device - make it -X mknod /dev/cuf$PORTNO c $CUAMAJOR $PORTNO -X fi -X done -X fi -done -X -Xexit 0 -SHAR_EOF - (set 20 01 10 29 10 32 01 'ip2mkdev'; eval "$shar_touch") && - chmod 0755 'ip2mkdev' || - $echo 'restore of' 'ip2mkdev' 'failed' - if ( md5sum --help 2>&1 | grep 'sage: md5sum \[' ) >/dev/null 2>&1 \ - && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then - md5sum -c << SHAR_EOF >/dev/null 2>&1 \ - || $echo 'ip2mkdev:' 'MD5 check failed' -cb5717134509f38bad9fde6b1f79b4a4 ip2mkdev -SHAR_EOF - else - shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'ip2mkdev'`" - test 4251 -eq "$shar_count" || - $echo 'ip2mkdev:' 'original size' '4251,' 'current size' "$shar_count!" - fi -fi -rm -fr _sh17581 -exit 0 diff --git a/Documentation/watchdog/src/watchdog-test.c b/Documentation/watchdog/src/watchdog-test.c index 73ff5cc93e0..3da822967ee 100644 --- a/Documentation/watchdog/src/watchdog-test.c +++ b/Documentation/watchdog/src/watchdog-test.c @@ -31,7 +31,7 @@ static void keep_alive(void) * or "-e" to enable the card. */ -void term(int sig) +static void term(int sig) { close(fd); fprintf(stderr, "Stopping watchdog ticks...\n"); |