diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/led.txt | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/vendor-prefixes.txt | 1 | ||||
| -rw-r--r-- | Documentation/hwmon/jc42 | 26 | ||||
| -rw-r--r-- | Documentation/input/alps.txt | 3 | ||||
| -rw-r--r-- | Documentation/input/event-codes.txt | 72 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 6 | ||||
| -rw-r--r-- | Documentation/sysctl/kernel.txt | 2 |
7 files changed, 98 insertions, 18 deletions
diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt index 141087cf310..fd2bd56e719 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device. Each node's name represents the name of the corresponding LED. LED sub-node properties: -- gpios : Should specify the LED's GPIO, see "Specifying GPIO information - for devices" in Documentation/devicetree/booting-without-of.txt. Active - low LEDs should be indicated using flags in the GPIO specifier. +- gpios : Should specify the LED's GPIO, see "gpios property" in + Documentation/devicetree/gpio.txt. Active low LEDs should be + indicated using flags in the GPIO specifier. - label : (optional) The label for this LED. If omitted, the label is taken from the node name (excluding the unit address). - linux,default-trigger : (optional) This parameter, if present, is a diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ecc6a6cd26c..a20008ab319 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -30,6 +30,7 @@ national National Semiconductor nintendo Nintendo nvidia NVIDIA nxp NXP Semiconductors +picochip Picochip Ltd powervr Imagination Technologies qcom Qualcomm, Inc. ramtron Ramtron International diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42 index a22ecf48f25..52729a756c1 100644 --- a/Documentation/hwmon/jc42 +++ b/Documentation/hwmon/jc42 @@ -7,21 +7,29 @@ Supported chips: Addresses scanned: I2C 0x18 - 0x1f Datasheets: http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf - * IDT TSE2002B3, TS3000B3 - Prefix: 'tse2002b3', 'ts3000b3' + * Atmel AT30TS00 + Prefix: 'at30ts00' Addresses scanned: I2C 0x18 - 0x1f Datasheets: - http://www.idt.com/products/getdoc.cfm?docid=18715691 - http://www.idt.com/products/getdoc.cfm?docid=18715692 + http://www.atmel.com/Images/doc8585.pdf + * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2 + Prefix: 'tse2002', 'ts3000' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf + http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf + http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf + http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf * Maxim MAX6604 Prefix: 'max6604' Addresses scanned: I2C 0x18 - 0x1f Datasheets: http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf - * Microchip MCP9805, MCP98242, MCP98243, MCP9843 - Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843' + * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP9843 + Prefixes: 'mcp9804', 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843' Addresses scanned: I2C 0x18 - 0x1f Datasheets: + http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf @@ -48,6 +56,12 @@ Supported chips: Datasheets: http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf + * ST Microelectronics STTS2002, STTS3000 + Prefix: 'stts2002', 'stts3000' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00225278.pdf + http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/CD00270920.pdf * JEDEC JC 42.4 compliant temperature sensor chips Prefix: 'jc42' Addresses scanned: I2C 0x18 - 0x1f diff --git a/Documentation/input/alps.txt b/Documentation/input/alps.txt index f274c28b510..2f95308251d 100644 --- a/Documentation/input/alps.txt +++ b/Documentation/input/alps.txt @@ -13,7 +13,8 @@ Detection All ALPS touchpads should respond to the "E6 report" command sequence: E8-E6-E6-E6-E9. An ALPS touchpad should respond with either 00-00-0A or -00-00-64. +00-00-64 if no buttons are pressed. The bits 0-2 of the first byte will be 1s +if some buttons are pressed. If the E6 report is successful, the touchpad model is identified using the "E7 report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is diff --git a/Documentation/input/event-codes.txt b/Documentation/input/event-codes.txt index 23fcb05175b..53305bd0818 100644 --- a/Documentation/input/event-codes.txt +++ b/Documentation/input/event-codes.txt @@ -17,11 +17,11 @@ reports supported by a device are also provided by sysfs in class/input/event*/device/capabilities/, and the properties of a device are provided in class/input/event*/device/properties. -Types: -========== -Types are groupings of codes under a logical input construct. Each type has a -set of applicable codes to be used in generating events. See the Codes section -for details on valid codes for each type. +Event types: +=========== +Event types are groupings of codes under a logical input construct. Each +type has a set of applicable codes to be used in generating events. See the +Codes section for details on valid codes for each type. * EV_SYN: - Used as markers to separate events. Events may be separated in time or in @@ -63,9 +63,9 @@ for details on valid codes for each type. * EV_FF_STATUS: - Used to receive force feedback device status. -Codes: -========== -Codes define the precise type of event. +Event codes: +=========== +Event codes define the precise type of event. EV_SYN: ---------- @@ -220,6 +220,56 @@ EV_PWR: EV_PWR events are a special type of event used specifically for power mangement. Its usage is not well defined. To be addressed later. +Device properties: +================= +Normally, userspace sets up an input device based on the data it emits, +i.e., the event types. In the case of two devices emitting the same event +types, additional information can be provided in the form of device +properties. + +INPUT_PROP_DIRECT + INPUT_PROP_POINTER: +-------------------------------------- +The INPUT_PROP_DIRECT property indicates that device coordinates should be +directly mapped to screen coordinates (not taking into account trivial +transformations, such as scaling, flipping and rotating). Non-direct input +devices require non-trivial transformation, such as absolute to relative +transformation for touchpads. Typical direct input devices: touchscreens, +drawing tablets; non-direct devices: touchpads, mice. + +The INPUT_PROP_POINTER property indicates that the device is not transposed +on the screen and thus requires use of an on-screen pointer to trace user's +movements. Typical pointer devices: touchpads, tablets, mice; non-pointer +device: touchscreen. + +If neither INPUT_PROP_DIRECT or INPUT_PROP_POINTER are set, the property is +considered undefined and the device type should be deduced in the +traditional way, using emitted event types. + +INPUT_PROP_BUTTONPAD: +-------------------- +For touchpads where the button is placed beneath the surface, such that +pressing down on the pad causes a button click, this property should be +set. Common in clickpad notebooks and macbooks from 2009 and onwards. + +Originally, the buttonpad property was coded into the bcm5974 driver +version field under the name integrated button. For backwards +compatibility, both methods need to be checked in userspace. + +INPUT_PROP_SEMI_MT: +------------------ +Some touchpads, most common between 2008 and 2011, can detect the presence +of multiple contacts without resolving the individual positions; only the +number of contacts and a rectangular shape is known. For such +touchpads, the semi-mt property should be set. + +Depending on the device, the rectangle may enclose all touches, like a +bounding box, or just some of them, for instance the two most recent +touches. The diversity makes the rectangle of limited use, but some +gestures can normally be extracted from it. + +If INPUT_PROP_SEMI_MT is not set, the device is assumed to be a true MT +device. + Guidelines: ========== The guidelines below ensure proper single-touch and multi-finger functionality. @@ -240,6 +290,8 @@ used to report when a touch is active on the screen. BTN_{MOUSE,LEFT,MIDDLE,RIGHT} must not be reported as the result of touch contact. BTN_TOOL_<name> events should be reported where possible. +For new hardware, INPUT_PROP_DIRECT should be set. + Trackpads: ---------- Legacy trackpads that only provide relative position information must report @@ -250,6 +302,8 @@ location of the touch. BTN_TOUCH should be used to report when a touch is active on the trackpad. Where multi-finger support is available, BTN_TOOL_<name> should be used to report the number of touches active on the trackpad. +For new hardware, INPUT_PROP_POINTER should be set. + Tablets: ---------- BTN_TOOL_<name> events must be reported when a stylus or other tool is active on @@ -260,3 +314,5 @@ button may be used for buttons on the tablet except BTN_{MOUSE,LEFT}. BTN_{0,1,2,etc} are good generic codes for unlabeled buttons. Do not use meaningful buttons, like BTN_FORWARD, unless the button is labeled for that purpose on the device. + +For new hardware, both INPUT_PROP_DIRECT and INPUT_PROP_POINTER should be set. diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 033d4e69b43..d99fd9c0ec0 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -2211,6 +2211,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. default: off. + printk.always_kmsg_dump= + Trigger kmsg_dump for cases other than kernel oops or + panics + Format: <bool> (1/Y/y=enable, 0/N/n=disable) + default: disabled + printk.time= Show timing data prefixed to each printk message line Format: <bool> (1/Y/y=enable, 0/N/n=disable) diff --git a/Documentation/sysctl/kernel.txt b/Documentation/sysctl/kernel.txt index 8c20fbd8b42..6d78841fd41 100644 --- a/Documentation/sysctl/kernel.txt +++ b/Documentation/sysctl/kernel.txt @@ -601,6 +601,8 @@ can be ORed together: instead of using the one provided by the hardware. 512 - A kernel warning has occurred. 1024 - A module from drivers/staging was loaded. +2048 - The system is working around a severe firmware bug. +4096 - An out-of-tree module has been loaded. ============================================================== |