diff options
Diffstat (limited to 'Documentation')
4 files changed, 97 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt new file mode 100644 index 00000000000..392a4493eeb --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt @@ -0,0 +1,24 @@ +NVIDIA Tegra20/Tegra30 high speed (DMA based) UART controller driver. + +Required properties: +- compatible : should be "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart". +- reg: Should contain UART controller registers location and length. +- interrupts: Should contain UART controller interrupts. +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this UART controller. + +Optional properties: +- nvidia,enable-modem-interrupt: Enable modem interrupts. Should be enable + only if all 8 lines of UART controller are pinmuxed. + +Example: + +serial@70006000 { + compatible = "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart"; + reg = <0x70006000 0x40>; + reg-shift = <2>; + interrupts = <0 36 0x04>; + nvidia,dma-request-selector = <&apbdma 8>; + nvidia,enable-modem-interrupt; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/arc-uart.txt b/Documentation/devicetree/bindings/tty/serial/arc-uart.txt new file mode 100644 index 00000000000..5cae2eb686f --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/arc-uart.txt @@ -0,0 +1,26 @@ +* Synopsys ARC UART : Non standard UART used in some of the ARC FPGA boards + +Required properties: +- compatible : "snps,arc-uart" +- reg : offset and length of the register set for the device. +- interrupts : device interrupt +- clock-frequency : the input clock frequency for the UART +- current-speed : baud rate for UART + +e.g. + +arcuart0: serial@c0fc1000 { + compatible = "snps,arc-uart"; + reg = <0xc0fc1000 0x100>; + interrupts = <5>; + clock-frequency = <80000000>; + current-speed = <115200>; + status = "okay"; +}; + +Note: Each port should have an alias correctly numbered in "aliases" node. + +e.g. +aliases { + serial0 = &arcuart0; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt index 6588b6950a7..8e080b893b4 100644 --- a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt +++ b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt @@ -5,10 +5,16 @@ Required properties: - reg : Address and length of the register set - interrupts : Should contain uart interrupt +Optional properties: +- location : Decides the location of the USART I/O pins. + Allowed range : [0 .. 5] + Default: 0 + Example: uart@0x4000c400 { compatible = "efm32,uart"; reg = <0x4000c400 0x400>; interrupts = <15>; + location = <0>; }; diff --git a/Documentation/serial/driver b/Documentation/serial/driver index 0a25a919186..067c47d4691 100644 --- a/Documentation/serial/driver +++ b/Documentation/serial/driver @@ -133,6 +133,16 @@ hardware. Interrupts: locally disabled. This call must not sleep + send_xchar(port,ch) + Transmit a high priority character, even if the port is stopped. + This is used to implement XON/XOFF flow control and tcflow(). If + the serial driver does not implement this function, the tty core + will append the character to the circular buffer and then call + start_tx() / stop_tx() to flush the data out. + + Locking: none. + Interrupts: caller dependent. + stop_rx(port) Stop receiving characters; the port is in the process of being closed. @@ -242,9 +252,8 @@ hardware. pm(port,state,oldstate) Perform any power management related activities on the specified - port. State indicates the new state (defined by ACPI D0-D3), - oldstate indicates the previous state. Essentially, D0 means - fully on, D3 means powered down. + port. State indicates the new state (defined by + enum uart_pm_state), oldstate indicates the previous state. This function should not be used to grab any resources. @@ -255,6 +264,10 @@ hardware. Locking: none. Interrupts: caller dependent. + set_wake(port,state) + Enable/disable power management wakeup on serial activity. Not + currently implemented. + type(port) Return a pointer to a string constant describing the specified port, or return NULL, in which case the string 'unknown' is @@ -307,6 +320,31 @@ hardware. Locking: none. Interrupts: caller dependent. + poll_init(port) + Called by kgdb to perform the minimal hardware initialization needed + to support poll_put_char() and poll_get_char(). Unlike ->startup() + this should not request interrupts. + + Locking: tty_mutex and tty_port->mutex taken. + Interrupts: n/a. + + poll_put_char(port,ch) + Called by kgdb to write a single character directly to the serial + port. It can and should block until there is space in the TX FIFO. + + Locking: none. + Interrupts: caller dependent. + This call must not sleep + + poll_get_char(port) + Called by kgdb to read a single character directly from the serial + port. If data is available, it should be returned; otherwise + the function should return NO_POLL_CHAR immediately. + + Locking: none. + Interrupts: caller dependent. + This call must not sleep + Other functions --------------- |