summaryrefslogtreecommitdiffstats
path: root/Documentation
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/networking/ray_cs.txt2
-rw-r--r--Documentation/sound/oss/Introduction2
-rw-r--r--Documentation/sound/oss/cs46xx16
3 files changed, 10 insertions, 10 deletions
diff --git a/Documentation/networking/ray_cs.txt b/Documentation/networking/ray_cs.txt
index 5427f8c7df9..145d27a5239 100644
--- a/Documentation/networking/ray_cs.txt
+++ b/Documentation/networking/ray_cs.txt
@@ -25,7 +25,7 @@ the essid= string parameter is available via the kernel command line.
This will change after the method of sorting out parameters for all
the PCMCIA drivers is agreed upon. If you must have a built in driver
with nondefault parameters, they can be edited in
-/usr/src/linux/drivers/net/pcmcia/ray_cs.c. Searching for MODULE_PARM
+/usr/src/linux/drivers/net/pcmcia/ray_cs.c. Searching for module_param
will find them all.
Information on card services is available at:
diff --git a/Documentation/sound/oss/Introduction b/Documentation/sound/oss/Introduction
index 15d4fb975ac..f04ba6bb739 100644
--- a/Documentation/sound/oss/Introduction
+++ b/Documentation/sound/oss/Introduction
@@ -69,7 +69,7 @@ are available, for example IRQ, address, DMA.
Warning, the options for different cards sometime use different names
for the same or a similar feature (dma1= versus dma16=). As a last
-resort, inspect the code (search for MODULE_PARM).
+resort, inspect the code (search for module_param).
Notes:
diff --git a/Documentation/sound/oss/cs46xx b/Documentation/sound/oss/cs46xx
index 88d6cf8b39f..b5443270986 100644
--- a/Documentation/sound/oss/cs46xx
+++ b/Documentation/sound/oss/cs46xx
@@ -88,7 +88,7 @@ parameters. for a copy email: twoller@crystal.cirrus.com
MODULE_PARMS definitions
------------------------
-MODULE_PARM(defaultorder, "i");
+module_param(defaultorder, ulong, 0);
defaultorder=N
where N is a value from 1 to 12
The buffer order determines the size of the dma buffer for the driver.
@@ -98,18 +98,18 @@ to not underrun the dma buffer as easily. As default, use 32k (order=3)
rather than 64k as some of the games work more responsively.
(2^N) * PAGE_SIZE = allocated buffer size
-MODULE_PARM(cs_debuglevel, "i");
-MODULE_PARM(cs_debugmask, "i");
+module_param(cs_debuglevel, ulong, 0644);
+module_param(cs_debugmask, ulong, 0644);
cs_debuglevel=N
cs_debugmask=0xMMMMMMMM
where N is a value from 0 (no debug printfs), to 9 (maximum)
0xMMMMMMMM is a debug mask corresponding to the CS_xxx bits (see driver source).
-MODULE_PARM(hercules_egpio_disable, "i");
+module_param(hercules_egpio_disable, ulong, 0);
hercules_egpio_disable=N
where N is a 0 (enable egpio), or a 1 (disable egpio support)
-MODULE_PARM(initdelay, "i");
+module_param(initdelay, ulong, 0);
initdelay=N
This value is used to determine the millescond delay during the initialization
code prior to powering up the PLL. On laptops this value can be used to
@@ -118,19 +118,19 @@ system is booted under battery power then the mdelay()/udelay() functions fail t
properly delay the required time. Also, if the system is booted under AC power
and then the power removed, the mdelay()/udelay() functions will not delay properly.
-MODULE_PARM(powerdown, "i");
+module_param(powerdown, ulong, 0);
powerdown=N
where N is 0 (disable any powerdown of the internal blocks) or 1 (enable powerdown)
-MODULE_PARM(external_amp, "i");
+module_param(external_amp, bool, 0);
external_amp=1
if N is set to 1, then force enabling the EAPD support in the primary AC97 codec.
override the detection logic and force the external amp bit in the AC97 0x26 register
to be reset (0). EAPD should be 0 for powerup, and 1 for powerdown. The VTB Santa Cruz
card has inverted logic, so there is a special function for these cards.
-MODULE_PARM(thinkpad, "i");
+module_param(thinkpad, bool, 0);
thinkpad=1
if N is set to 1, then force enabling the clkrun functionality.
Currently, when the part is being used, then clkrun is disabled for the entire system,