diff options
Diffstat (limited to 'Documentation')
24 files changed, 736 insertions, 72 deletions
diff --git a/Documentation/clk.txt b/Documentation/clk.txt index 6f68ba0d1e0..3aeb5c44044 100644 --- a/Documentation/clk.txt +++ b/Documentation/clk.txt @@ -70,6 +70,10 @@ the operations defined in clk.h: unsigned long parent_rate); long (*round_rate)(struct clk_hw *hw, unsigned long, unsigned long *); + long (*determine_rate)(struct clk_hw *hw, + unsigned long rate, + unsigned long *best_parent_rate, + struct clk **best_parent_clk); int (*set_parent)(struct clk_hw *hw, u8 index); u8 (*get_parent)(struct clk_hw *hw); int (*set_rate)(struct clk_hw *hw, unsigned long); @@ -179,26 +183,28 @@ mandatory, a cell marked as "n" implies that either including that callback is invalid or otherwise unnecessary. Empty cells are either optional or must be evaluated on a case-by-case basis. - clock hardware characteristics - ----------------------------------------------------------- - | gate | change rate | single parent | multiplexer | root | - |------|-------------|---------------|-------------|------| -.prepare | | | | | | -.unprepare | | | | | | - | | | | | | -.enable | y | | | | | -.disable | y | | | | | -.is_enabled | y | | | | | - | | | | | | -.recalc_rate | | y | | | | -.round_rate | | y | | | | -.set_rate | | y | | | | - | | | | | | -.set_parent | | | n | y | n | -.get_parent | | | n | y | n | - | | | | | | -.init | | | | | | - ----------------------------------------------------------- + clock hardware characteristics + ----------------------------------------------------------- + | gate | change rate | single parent | multiplexer | root | + |------|-------------|---------------|-------------|------| +.prepare | | | | | | +.unprepare | | | | | | + | | | | | | +.enable | y | | | | | +.disable | y | | | | | +.is_enabled | y | | | | | + | | | | | | +.recalc_rate | | y | | | | +.round_rate | | y [1] | | | | +.determine_rate | | y [1] | | | | +.set_rate | | y | | | | + | | | | | | +.set_parent | | | n | y | n | +.get_parent | | | n | y | n | + | | | | | | +.init | | | | | | + ----------------------------------------------------------- +[1] either one of round_rate or determine_rate is required. Finally, register your clock at run-time with a hardware-specific registration function. This function simply populates struct clk_foo's diff --git a/Documentation/device-mapper/cache.txt b/Documentation/device-mapper/cache.txt index e8cdf7241b6..33d45ee0b73 100644 --- a/Documentation/device-mapper/cache.txt +++ b/Documentation/device-mapper/cache.txt @@ -50,14 +50,16 @@ other parameters detailed later): which are dirty, and extra hints for use by the policy object. This information could be put on the cache device, but having it separate allows the volume manager to configure it differently, - e.g. as a mirror for extra robustness. + e.g. as a mirror for extra robustness. This metadata device may only + be used by a single cache device. Fixed block size ---------------- The origin is divided up into blocks of a fixed size. This block size is configurable when you first create the cache. Typically we've been -using block sizes of 256k - 1024k. +using block sizes of 256KB - 1024KB. The block size must be between 64 +(32KB) and 2097152 (1GB) and a multiple of 64 (32KB). Having a fixed block size simplifies the target a lot. But it is something of a compromise. For instance, a small part of a block may be diff --git a/Documentation/device-mapper/statistics.txt b/Documentation/device-mapper/statistics.txt new file mode 100644 index 00000000000..2a1673adc20 --- /dev/null +++ b/Documentation/device-mapper/statistics.txt @@ -0,0 +1,186 @@ +DM statistics +============= + +Device Mapper supports the collection of I/O statistics on user-defined +regions of a DM device. If no regions are defined no statistics are +collected so there isn't any performance impact. Only bio-based DM +devices are currently supported. + +Each user-defined region specifies a starting sector, length and step. +Individual statistics will be collected for each step-sized area within +the range specified. + +The I/O statistics counters for each step-sized area of a region are +in the same format as /sys/block/*/stat or /proc/diskstats (see: +Documentation/iostats.txt). But two extra counters (12 and 13) are +provided: total time spent reading and writing in milliseconds. All +these counters may be accessed by sending the @stats_print message to +the appropriate DM device via dmsetup. + +Each region has a corresponding unique identifier, which we call a +region_id, that is assigned when the region is created. The region_id +must be supplied when querying statistics about the region, deleting the +region, etc. Unique region_ids enable multiple userspace programs to +request and process statistics for the same DM device without stepping +on each other's data. + +The creation of DM statistics will allocate memory via kmalloc or +fallback to using vmalloc space. At most, 1/4 of the overall system +memory may be allocated by DM statistics. The admin can see how much +memory is used by reading +/sys/module/dm_mod/parameters/stats_current_allocated_bytes + +Messages +======== + + @stats_create <range> <step> [<program_id> [<aux_data>]] + + Create a new region and return the region_id. + + <range> + "-" - whole device + "<start_sector>+<length>" - a range of <length> 512-byte sectors + starting with <start_sector>. + + <step> + "<area_size>" - the range is subdivided into areas each containing + <area_size> sectors. + "/<number_of_areas>" - the range is subdivided into the specified + number of areas. + + <program_id> + An optional parameter. A name that uniquely identifies + the userspace owner of the range. This groups ranges together + so that userspace programs can identify the ranges they + created and ignore those created by others. + The kernel returns this string back in the output of + @stats_list message, but it doesn't use it for anything else. + + <aux_data> + An optional parameter. A word that provides auxiliary data + that is useful to the client program that created the range. + The kernel returns this string back in the output of + @stats_list message, but it doesn't use this value for anything. + + @stats_delete <region_id> + + Delete the region with the specified id. + + <region_id> + region_id returned from @stats_create + + @stats_clear <region_id> + + Clear all the counters except the in-flight i/o counters. + + <region_id> + region_id returned from @stats_create + + @stats_list [<program_id>] + + List all regions registered with @stats_create. + + <program_id> + An optional parameter. + If this parameter is specified, only matching regions + are returned. + If it is not specified, all regions are returned. + + Output format: + <region_id>: <start_sector>+<length> <step> <program_id> <aux_data> + + @stats_print <region_id> [<starting_line> <number_of_lines>] + + Print counters for each step-sized area of a region. + + <region_id> + region_id returned from @stats_create + + <starting_line> + The index of the starting line in the output. + If omitted, all lines are returned. + + <number_of_lines> + The number of lines to include in the output. + If omitted, all lines are returned. + + Output format for each step-sized area of a region: + + <start_sector>+<length> counters + + The first 11 counters have the same meaning as + /sys/block/*/stat or /proc/diskstats. + + Please refer to Documentation/iostats.txt for details. + + 1. the number of reads completed + 2. the number of reads merged + 3. the number of sectors read + 4. the number of milliseconds spent reading + 5. the number of writes completed + 6. the number of writes merged + 7. the number of sectors written + 8. the number of milliseconds spent writing + 9. the number of I/Os currently in progress + 10. the number of milliseconds spent doing I/Os + 11. the weighted number of milliseconds spent doing I/Os + + Additional counters: + 12. the total time spent reading in milliseconds + 13. the total time spent writing in milliseconds + + @stats_print_clear <region_id> [<starting_line> <number_of_lines>] + + Atomically print and then clear all the counters except the + in-flight i/o counters. Useful when the client consuming the + statistics does not want to lose any statistics (those updated + between printing and clearing). + + <region_id> + region_id returned from @stats_create + + <starting_line> + The index of the starting line in the output. + If omitted, all lines are printed and then cleared. + + <number_of_lines> + The number of lines to process. + If omitted, all lines are printed and then cleared. + + @stats_set_aux <region_id> <aux_data> + + Store auxiliary data aux_data for the specified region. + + <region_id> + region_id returned from @stats_create + + <aux_data> + The string that identifies data which is useful to the client + program that created the range. The kernel returns this + string back in the output of @stats_list message, but it + doesn't use this value for anything. + +Examples +======== + +Subdivide the DM device 'vol' into 100 pieces and start collecting +statistics on them: + + dmsetup message vol 0 @stats_create - /100 + +Set the auxillary data string to "foo bar baz" (the escape for each +space must also be escaped, otherwise the shell will consume them): + + dmsetup message vol 0 @stats_set_aux 0 foo\\ bar\\ baz + +List the statistics: + + dmsetup message vol 0 @stats_list + +Print the statistics: + + dmsetup message vol 0 @stats_print 0 + +Delete the statistics: + + dmsetup message vol 0 @stats_delete 0 diff --git a/Documentation/device-mapper/thin-provisioning.txt b/Documentation/device-mapper/thin-provisioning.txt index 30b8b83bd33..50c44cf79b0 100644 --- a/Documentation/device-mapper/thin-provisioning.txt +++ b/Documentation/device-mapper/thin-provisioning.txt @@ -99,13 +99,14 @@ Using an existing pool device $data_block_size $low_water_mark" $data_block_size gives the smallest unit of disk space that can be -allocated at a time expressed in units of 512-byte sectors. People -primarily interested in thin provisioning may want to use a value such -as 1024 (512KB). People doing lots of snapshotting may want a smaller value -such as 128 (64KB). If you are not zeroing newly-allocated data, -a larger $data_block_size in the region of 256000 (128MB) is suggested. -$data_block_size must be the same for the lifetime of the -metadata device. +allocated at a time expressed in units of 512-byte sectors. +$data_block_size must be between 128 (64KB) and 2097152 (1GB) and a +multiple of 128 (64KB). $data_block_size cannot be changed after the +thin-pool is created. People primarily interested in thin provisioning +may want to use a value such as 1024 (512KB). People doing lots of +snapshotting may want a smaller value such as 128 (64KB). If you are +not zeroing newly-allocated data, a larger $data_block_size in the +region of 256000 (128MB) is suggested. $low_water_mark is expressed in blocks of size $data_block_size. If free space on the data device drops below this level then a dm event diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt index 14d5c2af26f..c6bf8a6c8f5 100644 --- a/Documentation/devicetree/bindings/clock/exynos4-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos4-clock.txt @@ -236,6 +236,7 @@ Exynos4 SoC and this is specified where applicable. spi0_isp_sclk 380 Exynos4x12 spi1_isp_sclk 381 Exynos4x12 uart_isp_sclk 382 Exynos4x12 + tmu_apbif 383 [Mux Clocks] diff --git a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt index 781a6276adf..24765c146e3 100644 --- a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt @@ -59,6 +59,9 @@ clock which they consume. sclk_spi0 154 sclk_spi1 155 sclk_spi2 156 + div_i2s1 157 + div_i2s2 158 + sclk_hdmiphy 159 [Peripheral Clock Gates] @@ -154,7 +157,16 @@ clock which they consume. dsim0 341 dp 342 mixer 343 - hdmi 345 + hdmi 344 + g2d 345 + + + [Clock Muxes] + + Clock ID + ---------------------------- + mout_hdmi 1024 + Example 1: An example of a clock controller node is listed below. diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt index 9bcc4b1bff5..32aa34ecad3 100644 --- a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt @@ -59,6 +59,7 @@ clock which they consume. sclk_pwm 155 sclk_gscl_wa 156 sclk_gscl_wb 157 + sclk_hdmiphy 158 [Peripheral Clock Gates] @@ -179,6 +180,17 @@ clock which they consume. fimc_lite3 495 aclk_g3d 500 g3d 501 + smmu_mixer 502 + + Mux ID + ---------------------------- + + mout_hdmi 640 + + Divider ID + ---------------------------- + + dout_pixel 768 Example 1: An example of a clock controller node is listed below. diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt new file mode 100644 index 00000000000..fa171dc4bd3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt @@ -0,0 +1,77 @@ +* Samsung S3C64xx Clock Controller + +The S3C64xx clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to all SoCs in +the S3C64xx family. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c6400-clock" - controller compatible with S3C6400 SoC. + - "samsung,s3c6410-clock" - controller compatible with S3C6410 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular S3C64xx SoC and this is specified where applicable. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/samsung,s3c64xx-clock.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "fin_pll" - PLL input clock (xtal/extclk) - required, + - "xusbxti" - USB xtal - required, + - "iiscdclk0" - I2S0 codec clock - optional, + - "iiscdclk1" - I2S1 codec clock - optional, + - "iiscdclk2" - I2S2 codec clock - optional, + - "pcmcdclk0" - PCM0 codec clock - optional, + - "pcmcdclk1" - PCM1 codec clock - optional, only S3C6410. + +Example: Clock controller node: + + clock: clock-controller@7e00f000 { + compatible = "samsung,s3c6410-clock"; + reg = <0x7e00f000 0x1000>; + #clock-cells = <1>; + }; + +Example: Required external clocks: + + fin_pll: clock-fin-pll { + compatible = "fixed-clock"; + clock-output-names = "fin_pll"; + clock-frequency = <12000000>; + #clock-cells = <0>; + }; + + xusbxti: clock-xusbxti { + compatible = "fixed-clock"; + clock-output-names = "xusbxti"; + clock-frequency = <48000000>; + #clock-cells = <0>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + uart0: serial@7f005000 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005000 0x100>; + interrupt-parent = <&vic1>; + interrupts = <5>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clock PCLK_UART0>, <&clocks PCLK_UART0>, + <&clock SCLK_UART>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index d495521a79d..00a5c26454e 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -8,19 +8,31 @@ Required properties: - compatible : shall be one of the following: "allwinner,sun4i-osc-clk" - for a gatable oscillator "allwinner,sun4i-pll1-clk" - for the main PLL clock + "allwinner,sun6i-a31-pll1-clk" - for the main PLL clock on A31 "allwinner,sun4i-cpu-clk" - for the CPU multiplexer clock "allwinner,sun4i-axi-clk" - for the AXI clock "allwinner,sun4i-axi-gates-clk" - for the AXI gates "allwinner,sun4i-ahb-clk" - for the AHB clock "allwinner,sun4i-ahb-gates-clk" - for the AHB gates on A10 "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13 + "allwinner,sun5i-a10s-ahb-gates-clk" - for the AHB gates on A10s + "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20 + "allwinner,sun6i-a31-ahb1-mux-clk" - for the AHB1 multiplexer on A31 + "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31 "allwinner,sun4i-apb0-clk" - for the APB0 clock "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates on A10 "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13 + "allwinner,sun5i-a10s-apb0-gates-clk" - for the APB0 gates on A10s + "allwinner,sun7i-a20-apb0-gates-clk" - for the APB0 gates on A20 "allwinner,sun4i-apb1-clk" - for the APB1 clock "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates on A10 "allwinner,sun5i-a13-apb1-gates-clk" - for the APB1 gates on A13 + "allwinner,sun5i-a10s-apb1-gates-clk" - for the APB1 gates on A10s + "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31 + "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20 + "allwinner,sun6i-a31-apb2-div-clk" - for the APB2 gates on A31 + "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 Required properties for all clocks: - reg : shall be the control register address for the clock. diff --git a/Documentation/devicetree/bindings/clock/sunxi/sun5i-a10s-gates.txt b/Documentation/devicetree/bindings/clock/sunxi/sun5i-a10s-gates.txt new file mode 100644 index 00000000000..d24279fe142 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi/sun5i-a10s-gates.txt @@ -0,0 +1,75 @@ +Gate clock outputs +------------------ + + * AXI gates ("allwinner,sun4i-axi-gates-clk") + + DRAM 0 + + * AHB gates ("allwinner,sun5i-a10s-ahb-gates-clk") + + USB0 0 + EHCI0 1 + OHCI0 2 + + SS 5 + DMA 6 + BIST 7 + MMC0 8 + MMC1 9 + MMC2 10 + + NAND 13 + SDRAM 14 + + EMAC 17 + TS 18 + + SPI0 20 + SPI1 21 + SPI2 22 + + GPS 26 + + HSTIMER 28 + + VE 32 + + TVE 34 + + LCD 36 + + CSI 40 + + HDMI 43 + DE_BE 44 + + DE_FE 46 + + IEP 51 + MALI400 52 + + * APB0 gates ("allwinner,sun5i-a10s-apb0-gates-clk") + + CODEC 0 + + IIS 3 + + PIO 5 + IR 6 + + KEYPAD 10 + + * APB1 gates ("allwinner,sun5i-a10s-apb1-gates-clk") + + I2C0 0 + I2C1 1 + I2C2 2 + + UART0 16 + UART1 17 + UART2 18 + UART3 19 + +Notation: + [*]: The datasheet didn't mention these, but they are present on AW code + [**]: The datasheet had this marked as "NC" but they are used on AW code diff --git a/Documentation/devicetree/bindings/clock/sunxi/sun6i-a31-gates.txt b/Documentation/devicetree/bindings/clock/sunxi/sun6i-a31-gates.txt new file mode 100644 index 00000000000..fe44932b5c6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi/sun6i-a31-gates.txt @@ -0,0 +1,83 @@ +Gate clock outputs +------------------ + + * AHB1 gates ("allwinner,sun6i-a31-ahb1-gates-clk") + + MIPI DSI 1 + + SS 5 + DMA 6 + + MMC0 8 + MMC1 9 + MMC2 10 + MMC3 11 + + NAND1 12 + NAND0 13 + SDRAM 14 + + GMAC 17 + TS 18 + HSTIMER 19 + SPI0 20 + SPI1 21 + SPI2 22 + SPI3 23 + USB_OTG 24 + + EHCI0 26 + EHCI1 27 + + OHCI0 29 + OHCI1 30 + OHCI2 31 + VE 32 + + LCD0 36 + LCD1 37 + + CSI 40 + + HDMI 43 + DE_BE0 44 + DE_BE1 45 + DE_FE1 46 + DE_FE1 47 + + MP 50 + + GPU 52 + + DEU0 55 + DEU1 56 + DRC0 57 + DRC1 58 + + * APB1 gates ("allwinner,sun6i-a31-apb1-gates-clk") + + CODEC 0 + + DIGITAL MIC 4 + PIO 5 + + DAUDIO0 12 + DAUDIO1 13 + + * APB2 gates ("allwinner,sun6i-a31-apb2-gates-clk") + + I2C0 0 + I2C1 1 + I2C2 2 + I2C3 3 + + UART0 16 + UART1 17 + UART2 18 + UART3 19 + UART4 20 + UART5 21 + +Notation: + [*]: The datasheet didn't mention these, but they are present on AW code + [**]: The datasheet had this marked as "NC" but they are used on AW code diff --git a/Documentation/devicetree/bindings/clock/sunxi/sun7i-a20-gates.txt b/Documentation/devicetree/bindings/clock/sunxi/sun7i-a20-gates.txt new file mode 100644 index 00000000000..357f4fdc02e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi/sun7i-a20-gates.txt @@ -0,0 +1,98 @@ +Gate clock outputs +------------------ + + * AXI gates ("allwinner,sun4i-axi-gates-clk") + + DRAM 0 + + * AHB gates ("allwinner,sun7i-a20-ahb-gates-clk") + + USB0 0 + EHCI0 1 + OHCI0 2 + EHCI1 3 + OHCI1 4 + SS 5 + DMA 6 + BIST 7 + MMC0 8 + MMC1 9 + MMC2 10 + MMC3 11 + MS 12 + NAND 13 + SDRAM 14 + + ACE 16 + EMAC 17 + TS 18 + + SPI0 20 + SPI1 21 + SPI2 22 + SPI3 23 + + SATA 25 + + HSTIMER 28 + + VE 32 + TVD 33 + TVE0 34 + TVE1 35 + LCD0 36 + LCD1 37 + + CSI0 40 + CSI1 41 + + HDMI1 42 + HDMI0 43 + DE_BE0 44 + DE_BE1 45 + DE_FE1 46 + DE_FE1 47 + + GMAC 49 + MP 50 + + MALI400 52 + + * APB0 gates ("allwinner,sun7i-a20-apb0-gates-clk") + + CODEC 0 + SPDIF 1 + AC97 2 + IIS0 3 + IIS1 4 + PIO 5 + IR0 6 + IR1 7 + IIS2 8 + + KEYPAD 10 + + * APB1 gates ("allwinner,sun7i-a20-apb1-gates-clk") + + I2C0 0 + I2C1 1 + I2C2 2 + I2C3 3 + CAN 4 + SCR 5 + PS20 6 + PS21 7 + + I2C4 15 + UART0 16 + UART1 17 + UART2 18 + UART3 19 + UART4 20 + UART5 21 + UART6 22 + UART7 23 + +Notation: + [*]: The datasheet didn't mention these, but they are present on AW code + [**]: The datasheet had this marked as "NC" but they are used on AW code diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index 68cee4f5539..4fa814d3832 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -1,7 +1,12 @@ * Freescale Smart Direct Memory Access (SDMA) Controller for i.MX Required properties: -- compatible : Should be "fsl,<chip>-sdma" +- compatible : Should be "fsl,imx31-sdma", "fsl,imx31-to1-sdma", + "fsl,imx31-to2-sdma", "fsl,imx35-sdma", "fsl,imx35-to1-sdma", + "fsl,imx35-to2-sdma", "fsl,imx51-sdma", "fsl,imx53-sdma" or + "fsl,imx6q-sdma". The -to variants should be preferred since they + allow to determnine the correct ROM script addresses needed for + the driver to work without additional firmware. - reg : Should contain SDMA registers location and length - interrupts : Should contain SDMA interrupt - #dma-cells : Must be <3>. diff --git a/Documentation/devicetree/bindings/dma/k3dma.txt b/Documentation/devicetree/bindings/dma/k3dma.txt new file mode 100644 index 00000000000..23f8d712c3c --- /dev/null +++ b/Documentation/devicetree/bindings/dma/k3dma.txt @@ -0,0 +1,46 @@ +* Hisilicon K3 DMA controller + +See dma.txt first + +Required properties: +- compatible: Should be "hisilicon,k3-dma-1.0" +- reg: Should contain DMA registers location and length. +- interrupts: Should contain one interrupt shared by all channel +- #dma-cells: see dma.txt, should be 1, para number +- dma-channels: physical channels supported +- dma-requests: virtual channels supported, each virtual channel + have specific request line +- clocks: clock required + +Example: + +Controller: + dma0: dma@fcd02000 { + compatible = "hisilicon,k3-dma-1.0"; + reg = <0xfcd02000 0x1000>; + #dma-cells = <1>; + dma-channels = <16>; + dma-requests = <27>; + interrupts = <0 12 4>; + clocks = <&pclk>; + status = "disable"; + }; + +Client: +Use specific request line passing from dmax +For example, i2c0 read channel request line is 18, while write channel use 19 + + i2c0: i2c@fcb08000 { + compatible = "snps,designware-i2c"; + dmas = <&dma0 18 /* read channel */ + &dma0 19>; /* write channel */ + dma-names = "rx", "tx"; + }; + + i2c1: i2c@fcb09000 { + compatible = "snps,designware-i2c"; + dmas = <&dma0 20 /* read channel */ + &dma0 21>; /* write channel */ + dma-names = "rx", "tx"; + }; + diff --git a/Documentation/devicetree/bindings/dma/shdma.txt b/Documentation/devicetree/bindings/dma/shdma.txt index c15994aa193..2a3f3b8946b 100644 --- a/Documentation/devicetree/bindings/dma/shdma.txt +++ b/Documentation/devicetree/bindings/dma/shdma.txt @@ -22,42 +22,51 @@ Optional properties (currently unused): * DMA controller Required properties: -- compatible: should be "renesas,shdma" +- compatible: should be of the form "renesas,shdma-<soc>", where <soc> should + be replaced with the desired SoC model, e.g. + "renesas,shdma-r8a73a4" for the system DMAC on r8a73a4 SoC Example: - dmac: dma-mux0 { + dmac: dma-multiplexer@0 { compatible = "renesas,shdma-mux"; #dma-cells = <1>; - dma-channels = <6>; + dma-channels = <20>; dma-requests = <256>; - reg = <0 0>; /* Needed for AUXDATA */ - #address-cells = <1>; - #size-cells = <1>; + #address-cells = <2>; + #size-cells = <2>; ranges; - dma0: shdma@fe008020 { - compatible = "renesas,shdma"; - reg = <0xfe008020 0x270>, - <0xfe009000 0xc>; + dma0: dma-controller@e6700020 { + compatible = "renesas,shdma-r8a73a4"; + reg = <0 0xe6700020 0 0x89e0>; interrupt-parent = <&gic>; - interrupts = <0 34 4 - 0 28 4 - 0 29 4 - 0 30 4 - 0 31 4 - 0 32 4 - 0 33 4>; + interrupts = <0 220 4 + 0 200 4 + 0 201 4 + 0 202 4 + 0 203 4 + 0 204 4 + 0 205 4 + 0 206 4 + 0 207 4 + 0 208 4 + 0 209 4 + 0 210 4 + 0 211 4 + 0 212 4 + 0 213 4 + 0 214 4 + 0 215 4 + 0 216 4 + 0 217 4 + 0 218 4 + 0 219 4>; interrupt-names = "error", "ch0", "ch1", "ch2", "ch3", - "ch4", "ch5"; - }; - - dma1: shdma@fe018020 { - ... - }; - - dma2: shdma@fe028020 { - ... + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19"; }; }; diff --git a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt index 3f454ffc654..c4f358dafda 100644 --- a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt +++ b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt @@ -11,8 +11,11 @@ Required properties: - interrupts : G2D interrupt number to the CPU. - clocks : from common clock binding: handle to G2D clocks. - - clock-names : from common clock binding: must contain "sclk_fimg2d" and - "fimg2d", corresponding to entries in the clocks property. + - clock-names : names of clocks listed in clocks property, in the same + order, depending on SoC type: + - for S5PV210 and Exynos4 based SoCs: "fimg2d" and + "sclk_fimg2d" + - for Exynos5250 SoC: "fimg2d". Example: g2d@12800000 { diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index bd9be0b5bc2..b7943f3f999 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -19,6 +19,9 @@ Optional properties: "bus-width = <1>" property. - sdhci,auto-cmd12: specifies that a controller can only handle auto CMD12. + - voltage-ranges : two cells are required, first cell specifies minimum + slot voltage (mV), second cell specifies maximum slot voltage (mV). + Several ranges could be specified. Example: @@ -29,4 +32,5 @@ sdhci@2e000 { interrupt-parent = <&ipic>; /* Filled in by U-Boot */ clock-frequency = <0>; + voltage-ranges = <3300 3300>; }; diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt index c2dbcec0ee3..f2105a47ec8 100644 --- a/Documentation/devicetree/bindings/net/can/sja1000.txt +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -37,7 +37,7 @@ Optional properties: If not specified or if the specified value is 0, the CLKOUT pin will be disabled. -- nxp,no-comparator-bypass : Allows to disable the CAN input comperator. +- nxp,no-comparator-bypass : Allows to disable the CAN input comparator. For further information, please have a look to the SJA1000 data sheet. diff --git a/Documentation/devicetree/bindings/power_supply/msm-poweroff.txt b/Documentation/devicetree/bindings/power_supply/msm-poweroff.txt new file mode 100644 index 00000000000..ce44ad35756 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/msm-poweroff.txt @@ -0,0 +1,17 @@ +MSM Restart Driver + +A power supply hold (ps-hold) bit is set to power the msm chipsets. +Clearing that bit allows us to restart/poweroff. The difference +between poweroff and restart is determined by unique power manager IC +settings. + +Required Properties: +-compatible: "qcom,pshold" +-reg: Specifies the physical address of the ps-hold register + +Example: + + restart@fc4ab000 { + compatible = "qcom,pshold"; + reg = <0xfc4ab000 0x4>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt index 4caa1a78863..d61fccd40ba 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt @@ -19,6 +19,16 @@ Required properties: - reg: base address and size of register area - interrupts: list of timer interrupts (one interrupt per timer, starting at timer 0) +- clock-names: should contain all following required clock names: + - "timers" - PWM base clock used to generate PWM signals, + and any subset of following optional clock names: + - "pwm-tclk0" - first external PWM clock source, + - "pwm-tclk1" - second external PWM clock source. + Note that not all IP variants allow using all external clock sources. + Refer to SoC documentation to learn which clock source configurations + are available. +- clocks: should contain clock specifiers of all clocks, which input names + have been specified in clock-names property, in same order. - #pwm-cells: should be 3. See pwm.txt in this directory for a description of the cells format. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. @@ -34,6 +44,8 @@ Example: reg = <0x7f006000 0x1000>; interrupt-parent = <&vic0>; interrupts = <23>, <24>, <25>, <27>, <28>; + clocks = <&clock 67>; + clock-names = "timers"; samsung,pwm-outputs = <0>, <1>; #pwm-cells = <3>; } diff --git a/Documentation/dmatest.txt b/Documentation/dmatest.txt index 132a094c7bc..a2b5663eae2 100644 --- a/Documentation/dmatest.txt +++ b/Documentation/dmatest.txt @@ -16,15 +16,16 @@ be built as module or inside kernel. Let's consider those cases. Part 2 - When dmatest is built as a module... After mounting debugfs and loading the module, the /sys/kernel/debug/dmatest -folder with nodes will be created. They are the same as module parameters with -addition of the 'run' node that controls run and stop phases of the test. +folder with nodes will be created. There are two important files located. First +is the 'run' node that controls run and stop phases of the test, and the second +one, 'results', is used to get the test case results. Note that in this case test will not run on load automatically. Example of usage: - % echo dma0chan0 > /sys/kernel/debug/dmatest/channel - % echo 2000 > /sys/kernel/debug/dmatest/timeout - % echo 1 > /sys/kernel/debug/dmatest/iterations + % echo dma0chan0 > /sys/module/dmatest/parameters/channel + % echo 2000 > /sys/module/dmatest/parameters/timeout + % echo 1 > /sys/module/dmatest/parameters/iterations % echo 1 > /sys/kernel/debug/dmatest/run Hint: available channel list could be extracted by running the following @@ -55,8 +56,8 @@ for the first performed test. After user gets a control, the test could be re-run with the same or different parameters. For the details see the above section "Part 2 - When dmatest is built as a module..." -In both cases the module parameters are used as initial values for the test case. -You always could check them at run-time by running +In both cases the module parameters are used as the actual values for the test +case. You always could check them at run-time by running % grep -H . /sys/module/dmatest/parameters/* Part 4 - Gathering the test results diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt index fb57d85e731..fcb34a5697e 100644 --- a/Documentation/driver-model/devres.txt +++ b/Documentation/driver-model/devres.txt @@ -299,3 +299,6 @@ PWM PHY devm_usb_get_phy() devm_usb_put_phy() + +SLAVE DMA ENGINE + devm_acpi_dma_controller_register() diff --git a/Documentation/kbuild/kconfig-language.txt b/Documentation/kbuild/kconfig-language.txt index c858f8419eb..c420676c6fe 100644 --- a/Documentation/kbuild/kconfig-language.txt +++ b/Documentation/kbuild/kconfig-language.txt @@ -147,6 +147,7 @@ applicable everywhere (see syntax). - "modules" This declares the symbol to be used as the MODULES symbol, which enables the third modular state for all config symbols. + At most one symbol may have the "modules" option set. - "env"=<value> This imports the environment variable into Kconfig. It behaves like diff --git a/Documentation/kbuild/kconfig.txt b/Documentation/kbuild/kconfig.txt index e349f293cc9..8ef6dbb6a46 100644 --- a/Documentation/kbuild/kconfig.txt +++ b/Documentation/kbuild/kconfig.txt @@ -175,11 +175,9 @@ Searching in menuconfig: /^hotplug When searching, symbols are sorted thus: - - exact match first: an exact match is when the search matches - the complete symbol name; - - alphabetical order: when two symbols do not match exactly, - they are sorted in alphabetical order (in the user's current - locale). + - first, exact matches, sorted alphabetically (an exact match + is when the search matches the complete symbol name); + - then, other matches, sorted alphabetically. For example: ^ATH.K matches: ATH5K ATH9K ATH5K_AHB ATH5K_DEBUG [...] ATH6KL ATH6KL_DEBUG [...] ATH9K_AHB ATH9K_BTCOEX_SUPPORT ATH9K_COMMON [...] |