diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/arm/Samsung-S3C24XX/GPIO.txt | 81 | ||||
| -rw-r--r-- | Documentation/arm/Samsung-S3C24XX/Overview.txt | 15 | ||||
| -rw-r--r-- | Documentation/arm/Samsung/GPIO.txt | 42 | ||||
| -rw-r--r-- | Documentation/arm/Samsung/Overview.txt | 33 | ||||
| -rw-r--r-- | Documentation/filesystems/Locking | 2 | ||||
| -rw-r--r-- | Documentation/filesystems/vfs.txt | 9 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 2 |
7 files changed, 168 insertions, 16 deletions
diff --git a/Documentation/arm/Samsung-S3C24XX/GPIO.txt b/Documentation/arm/Samsung-S3C24XX/GPIO.txt index 2af2cf39915..816d6071669 100644 --- a/Documentation/arm/Samsung-S3C24XX/GPIO.txt +++ b/Documentation/arm/Samsung-S3C24XX/GPIO.txt @@ -12,6 +12,8 @@ Introduction of the s3c2410 GPIO system, please read the Samsung provided data-sheet/users manual to find out the complete list. + See Documentation/arm/Samsung/GPIO.txt for the core implemetation. + GPIOLIB ------- @@ -24,8 +26,60 @@ GPIOLIB listed below will be removed (they may be marked as __deprecated in the near future). - - s3c2410_gpio_getpin - - s3c2410_gpio_setpin + The following functions now either have a s3c_ specific variant + or are merged into gpiolib. See the definitions in + arch/arm/plat-samsung/include/plat/gpio-cfg.h: + + s3c2410_gpio_setpin() gpio_set_value() or gpio_direction_output() + s3c2410_gpio_getpin() gpio_get_value() or gpio_direction_input() + s3c2410_gpio_getirq() gpio_to_irq() + s3c2410_gpio_cfgpin() s3c_gpio_cfgpin() + s3c2410_gpio_getcfg() s3c_gpio_getcfg() + s3c2410_gpio_pullup() s3c_gpio_setpull() + + +GPIOLIB conversion +------------------ + +If you need to convert your board or driver to use gpiolib from the exiting +s3c2410 api, then here are some notes on the process. + +1) If your board is exclusively using an GPIO, say to control peripheral + power, then it will require to claim the gpio with gpio_request() before + it can use it. + + It is recommended to check the return value, with at least WARN_ON() + during initialisation. + +2) The s3c2410_gpio_cfgpin() can be directly replaced with s3c_gpio_cfgpin() + as they have the same arguments, and can either take the pin specific + values, or the more generic special-function-number arguments. + +3) s3c2410_gpio_pullup() changs have the problem that whilst the + s3c2410_gpio_pullup(x, 1) can be easily translated to the + s3c_gpio_setpull(x, S3C_GPIO_PULL_NONE), the s3c2410_gpio_pullup(x, 0) + are not so easy. + + The s3c2410_gpio_pullup(x, 0) case enables the pull-up (or in the case + of some of the devices, a pull-down) and as such the new API distinguishes + between the UP and DOWN case. There is currently no 'just turn on' setting + which may be required if this becomes a problem. + +4) s3c2410_gpio_setpin() can be replaced by gpio_set_value(), the old call + does not implicitly configure the relevant gpio to output. The gpio + direction should be changed before using gpio_set_value(). + +5) s3c2410_gpio_getpin() is replaceable by gpio_get_value() if the pin + has been set to input. It is currently unknown what the behaviour is + when using gpio_get_value() on an output pin (s3c2410_gpio_getpin + would return the value the pin is supposed to be outputting). + +6) s3c2410_gpio_getirq() should be directly replacable with the + gpio_to_irq() call. + +The s3c2410_gpio and gpio_ calls have always operated on the same gpio +numberspace, so there is no problem with converting the gpio numbering +between the calls. Headers @@ -54,6 +108,11 @@ PIN Numbers eg S3C2410_GPA(0) or S3C2410_GPF(1). These defines are used to tell the GPIO functions which pin is to be used. + With the conversion to gpiolib, there is no longer a direct conversion + from gpio pin number to register base address as in earlier kernels. This + is due to the number space required for newer SoCs where the later + GPIOs are not contiguous. + Configuring a pin ----------------- @@ -71,6 +130,8 @@ Configuring a pin which would turn GPA(0) into the lowest Address line A0, and set GPE(8) to be connected to the SDIO/MMC controller's SDDAT1 line. + The s3c_gpio_cfgpin() call is a functional replacement for this call. + Reading the current configuration --------------------------------- @@ -82,6 +143,9 @@ Reading the current configuration The return value will be from the same set of values which can be passed to s3c2410_gpio_cfgpin(). + The s3c_gpio_getcfg() call should be a functional replacement for + this call. + Configuring a pull-up resistor ------------------------------ @@ -95,6 +159,10 @@ Configuring a pull-up resistor Where the to value is zero to set the pull-up off, and 1 to enable the specified pull-up. Any other values are currently undefined. + The s3c_gpio_setpull() offers similar functionality, but with the + ability to encode whether the pull is up or down. Currently there + is no 'just on' state, so up or down must be selected. + Getting the state of a PIN -------------------------- @@ -106,6 +174,9 @@ Getting the state of a PIN This will return either zero or non-zero. Do not count on this function returning 1 if the pin is set. + This call is now implemented by the relevant gpiolib calls, convert + your board or driver to use gpiolib. + Setting the state of a PIN -------------------------- @@ -117,6 +188,9 @@ Setting the state of a PIN Which sets the given pin to the value. Use 0 to write 0, and 1 to set the output to 1. + This call is now implemented by the relevant gpiolib calls, convert + your board or driver to use gpiolib. + Getting the IRQ number associated with a PIN -------------------------------------------- @@ -128,6 +202,9 @@ Getting the IRQ number associated with a PIN Note, not all pins have an IRQ. + This call is now implemented by the relevant gpiolib calls, convert + your board or driver to use gpiolib. + Authour ------- diff --git a/Documentation/arm/Samsung-S3C24XX/Overview.txt b/Documentation/arm/Samsung-S3C24XX/Overview.txt index 081892df4fd..c12bfc1a00c 100644 --- a/Documentation/arm/Samsung-S3C24XX/Overview.txt +++ b/Documentation/arm/Samsung-S3C24XX/Overview.txt @@ -8,10 +8,16 @@ Introduction The Samsung S3C24XX range of ARM9 System-on-Chip CPUs are supported by the 's3c2410' architecture of ARM Linux. Currently the S3C2410, - S3C2412, S3C2413, S3C2440, S3C2442 and S3C2443 devices are supported. + S3C2412, S3C2413, S3C2416 S3C2440, S3C2442, S3C2443 and S3C2450 devices + are supported. Support for the S3C2400 and S3C24A0 series are in progress. + The S3C2416 and S3C2450 devices are very similar and S3C2450 support is + included under the arch/arm/mach-s3c2416 directory. Note, whilst core + support for these SoCs is in, work on some of the extra peripherals + and extra interrupts is still ongoing. + Configuration ------------- @@ -209,6 +215,13 @@ GPIO Newer kernels carry GPIOLIB, and support is being moved towards this with some of the older support in line to be removed. + As of v2.6.34, the move towards using gpiolib support is almost + complete, and very little of the old calls are left. + + See Documentation/arm/Samsung-S3C24XX/GPIO.txt for the S3C24XX specific + support and Documentation/arm/Samsung/GPIO.txt for the core Samsung + implementation. + Clock Management ---------------- diff --git a/Documentation/arm/Samsung/GPIO.txt b/Documentation/arm/Samsung/GPIO.txt new file mode 100644 index 00000000000..05850c62abe --- /dev/null +++ b/Documentation/arm/Samsung/GPIO.txt @@ -0,0 +1,42 @@ + Samsung GPIO implementation + =========================== + +Introduction +------------ + +This outlines the Samsung GPIO implementation and the architecture +specfic calls provided alongisde the drivers/gpio core. + + +S3C24XX (Legacy) +---------------- + +See Documentation/arm/Samsung-S3C24XX/GPIO.txt for more information +about these devices. Their implementation is being brought into line +with the core samsung implementation described in this document. + + +GPIOLIB integration +------------------- + +The gpio implementation uses gpiolib as much as possible, only providing +specific calls for the items that require Samsung specific handling, such +as pin special-function or pull resistor control. + +GPIO numbering is synchronised between the Samsung and gpiolib system. + + +PIN configuration +----------------- + +Pin configuration is specific to the Samsung architecutre, with each SoC +registering the necessary information for the core gpio configuration +implementation to configure pins as necessary. + +The s3c_gpio_cfgpin() and s3c_gpio_setpull() provide the means for a +driver or machine to change gpio configuration. + +See arch/arm/plat-samsung/include/plat/gpio-cfg.h for more information +on these functions. + + diff --git a/Documentation/arm/Samsung/Overview.txt b/Documentation/arm/Samsung/Overview.txt index 7cced1fea9c..c3094ea51aa 100644 --- a/Documentation/arm/Samsung/Overview.txt +++ b/Documentation/arm/Samsung/Overview.txt @@ -13,9 +13,10 @@ Introduction - S3C24XX: See Documentation/arm/Samsung-S3C24XX/Overview.txt for full list - S3C64XX: S3C6400 and S3C6410 - - S5PC6440 - - S5PC100 and S5PC110 support is currently being merged + - S5P6440 + - S5P6442 + - S5PC100 + - S5PC110 / S5PV210 S3C24XX Systems @@ -35,7 +36,10 @@ Configuration unifying all the SoCs into one kernel. s5p6440_defconfig - S5P6440 specific default configuration + s5p6442_defconfig - S5P6442 specific default configuration s5pc100_defconfig - S5PC100 specific default configuration + s5pc110_defconfig - S5PC110 specific default configuration + s5pv210_defconfig - S5PV210 specific default configuration Layout @@ -50,18 +54,27 @@ Layout specific information. It contains the base clock, GPIO and device definitions to get the system running. - plat-s3c is the s3c24xx/s3c64xx platform directory, although it is currently - involved in other builds this will be phased out once the relevant code is - moved elsewhere. - plat-s3c24xx is for s3c24xx specific builds, see the S3C24XX docs. - plat-s3c64xx is for the s3c64xx specific bits, see the S3C24XX docs. + plat-s5p is for s5p specific builds, and contains common support for the + S5P specific systems. Not all S5Ps use all the features in this directory + due to differences in the hardware. + + +Layout changes +-------------- + + The old plat-s3c and plat-s5pc1xx directories have been removed, with + support moved to either plat-samsung or plat-s5p as necessary. These moves + where to simplify the include and dependency issues involved with having + so many different platform directories. - plat-s5p is for s5p specific builds, more to be added. + It was decided to remove plat-s5pc1xx as some of the support was already + in plat-s5p or plat-samsung, with the S5PC110 support added with S5PV210 + the only user was the S5PC100. The S5PC100 specific items where moved to + arch/arm/mach-s5pc100. - [ to finish ] Port Contributors diff --git a/Documentation/filesystems/Locking b/Documentation/filesystems/Locking index 61c98f03baa..96d4293607e 100644 --- a/Documentation/filesystems/Locking +++ b/Documentation/filesystems/Locking @@ -380,7 +380,7 @@ prototypes: int (*open) (struct inode *, struct file *); int (*flush) (struct file *); int (*release) (struct inode *, struct file *); - int (*fsync) (struct file *, struct dentry *, int datasync); + int (*fsync) (struct file *, int datasync); int (*aio_fsync) (struct kiocb *, int datasync); int (*fasync) (int, struct file *, int); int (*lock) (struct file *, int, struct file_lock *); diff --git a/Documentation/filesystems/vfs.txt b/Documentation/filesystems/vfs.txt index b66858538df..94677e7dcb1 100644 --- a/Documentation/filesystems/vfs.txt +++ b/Documentation/filesystems/vfs.txt @@ -401,11 +401,16 @@ otherwise noted. started might not be in the page cache at the end of the walk). - truncate: called by the VFS to change the size of a file. The + truncate: Deprecated. This will not be called if ->setsize is defined. + Called by the VFS to change the size of a file. The i_size field of the inode is set to the desired size by the VFS before this method is called. This method is called by the truncate(2) system call and related functionality. + Note: ->truncate and vmtruncate are deprecated. Do not add new + instances/calls of these. Filesystems should be converted to do their + truncate sequence via ->setattr(). + permission: called by the VFS to check for access rights on a POSIX-like filesystem. @@ -729,7 +734,7 @@ struct file_operations { int (*open) (struct inode *, struct file *); int (*flush) (struct file *); int (*release) (struct inode *, struct file *); - int (*fsync) (struct file *, struct dentry *, int datasync); + int (*fsync) (struct file *, int datasync); int (*aio_fsync) (struct kiocb *, int datasync); int (*fasync) (int, struct file *, int); int (*lock) (struct file *, int, struct file_lock *); diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index b56ea860da2..a5c05506676 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1252,6 +1252,8 @@ and is between 256 and 4096 characters. It is defined in the file * nohrst, nosrst, norst: suppress hard, soft and both resets. + * dump_id: dump IDENTIFY data. + If there are multiple matching configurations changing the same attribute, the last one is used. |