diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/net/sti-dwmac.txt | 58 | ||||
| -rw-r--r-- | Documentation/networking/3c505.txt | 45 |
2 files changed, 58 insertions, 45 deletions
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt new file mode 100644 index 00000000000..3dd3d0bf112 --- /dev/null +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -0,0 +1,58 @@ +STMicroelectronics SoC DWMAC glue layer controller + +The device node has following properties. + +Required properties: + - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac" or + "st,stid127-dwmac". + - reg : Offset of the glue configuration register map in system + configuration regmap pointed by st,syscon property and size. + + - reg-names : Should be "sti-ethconf". + + - st,syscon : Should be phandle to system configuration node which + encompases this glue registers. + + - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be + wired up in from different sources. One via TXCLK pin and other via CLK_125 + pin. This wiring is totally board dependent. However the retiming glue + logic should be configured accordingly. Possible values for this property + + "txclk" - if 125Mhz clock is wired up via txclk line. + "clk_125" - if 125Mhz clock is wired up via clk_125 line. + + This property is only valid for Giga bit setup( GMII, RGMII), and it is + un-used for non-giga bit (MII and RMII) setups. Also note that internal + clockgen can not generate stable 125Mhz clock. + + - st,ext-phyclk: This boolean property indicates who is generating the clock + for tx and rx. This property is only valid for RMII case where the clock can + be generated from the MAC or PHY. + + - clock-names: should be "sti-ethclk". + - clocks: Should point to ethernet clockgen which can generate phyclk. + + +Example: + +ethernet0: dwmac@fe810000 { + device_type = "network"; + compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + reg = <0xfe810000 0x8000>, <0x8bc 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + interrupts = <0 133 0>, <0 134 0>, <0 135 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + phy-mode = "mii"; + + st,syscon = <&syscfg_rear>; + + snps,pbl = <32>; + snps,mixed-burst; + + resets = <&softreset STIH416_ETH0_SOFTRESET>; + reset-names = "stmmaceth"; + pinctrl-0 = <&pinctrl_mii0>; + pinctrl-names = "default"; + clocks = <&CLK_S_GMAC0_PHY>; + clock-names = "stmmaceth"; +}; diff --git a/Documentation/networking/3c505.txt b/Documentation/networking/3c505.txt deleted file mode 100644 index 72f38b13101..00000000000 --- a/Documentation/networking/3c505.txt +++ /dev/null @@ -1,45 +0,0 @@ -The 3Com Etherlink Plus (3c505) driver. - -This driver now uses DMA. There is currently no support for PIO operation. -The default DMA channel is 6; this is _not_ autoprobed, so you must -make sure you configure it correctly. If loading the driver as a -module, you can do this with "modprobe 3c505 dma=n". If the driver is -linked statically into the kernel, you must either use an "ether=" -statement on the command line, or change the definition of ELP_DMA in 3c505.h. - -The driver will warn you if it has to fall back on the compiled in -default DMA channel. - -If no base address is given at boot time, the driver will autoprobe -ports 0x300, 0x280 and 0x310 (in that order). If no IRQ is given, the driver -will try to probe for it. - -The driver can be used as a loadable module. - -Theoretically, one instance of the driver can now run multiple cards, -in the standard way (when loading a module, say "modprobe 3c505 -io=0x300,0x340 irq=10,11 dma=6,7" or whatever). I have not tested -this, though. - -The driver may now support revision 2 hardware; the dependency on -being able to read the host control register has been removed. This -is also untested, since I don't have a suitable card. - -Known problems: - I still see "DMA upload timed out" messages from time to time. These -seem to be fairly non-fatal though. - The card is old and slow. - -To do: - Improve probe/setup code - Test multicast and promiscuous operation - -Authors: - The driver is mainly written by Craig Southeren, email - <craigs@ineluki.apana.org.au>. - Parts of the driver (adapting the driver to 1.1.4+ kernels, - IRQ/address detection, some changes) and this README by - Juha Laiho <jlaiho@ichaos.nullnet.fi>. - DMA mode, more fixes, etc, by Philip Blundell <pjb27@cam.ac.uk> - Multicard support, Software configurable DMA, etc., by - Christopher Collins <ccollins@pcug.org.au> |