diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-usb | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/ci13xxx-imx.txt | 2 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/ehci-omap.txt | 32 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/ohci-omap3.txt | 15 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/omap-usb.txt | 40 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/samsung-usbphy.txt | 76 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt | 34 | ||||
| -rw-r--r-- | Documentation/ioctl/ioctl-number.txt | 1 | ||||
| -rw-r--r-- | Documentation/usb/power-management.txt | 10 |
9 files changed, 196 insertions, 20 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb index c8baaf53594..f093e59cbe5 100644 --- a/Documentation/ABI/testing/sysfs-bus-usb +++ b/Documentation/ABI/testing/sysfs-bus-usb @@ -32,7 +32,7 @@ Date: January 2008 KernelVersion: 2.6.25 Contact: Sarah Sharp <sarah.a.sharp@intel.com> Description: - If CONFIG_PM and CONFIG_USB_SUSPEND are enabled, then this file + If CONFIG_PM_RUNTIME is enabled then this file is present. When read, it returns the total time (in msec) that the USB device has been connected to the machine. This file is read-only. @@ -45,7 +45,7 @@ Date: January 2008 KernelVersion: 2.6.25 Contact: Sarah Sharp <sarah.a.sharp@intel.com> Description: - If CONFIG_PM and CONFIG_USB_SUSPEND are enabled, then this file + If CONFIG_PM_RUNTIME is enabled then this file is present. When read, it returns the total time (in msec) that the USB device has been active, i.e. not in a suspended state. This file is read-only. @@ -187,7 +187,7 @@ What: /sys/bus/usb/devices/.../power/usb2_hardware_lpm Date: September 2011 Contact: Andiry Xu <andiry.xu@amd.com> Description: - If CONFIG_USB_SUSPEND is set and a USB 2.0 lpm-capable device + If CONFIG_PM_RUNTIME is set and a USB 2.0 lpm-capable device is plugged in to a xHCI host which support link PM, it will perform a LPM test; if the test is passed and host supports USB2 hardware LPM (xHCI 1.0 feature), USB2 hardware LPM will diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt index 5778b9c83bd..1c04a4c9515 100644 --- a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt +++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt @@ -11,6 +11,7 @@ Optional properties: that indicate usb controller index - vbus-supply: regulator for vbus - disable-over-current: disable over current detect +- external-vbus-divider: enables off-chip resistor divider for Vbus Examples: usb@02184000 { /* USB OTG */ @@ -20,4 +21,5 @@ usb@02184000 { /* USB OTG */ fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; disable-over-current; + external-vbus-divider; }; diff --git a/Documentation/devicetree/bindings/usb/ehci-omap.txt b/Documentation/devicetree/bindings/usb/ehci-omap.txt new file mode 100644 index 00000000000..485a9a1efa7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-omap.txt @@ -0,0 +1,32 @@ +OMAP HS USB EHCI controller + +This device is usually the child of the omap-usb-host +Documentation/devicetree/bindings/mfd/omap-usb-host.txt + +Required properties: + +- compatible: should be "ti,ehci-omap" +- reg: should contain one register range i.e. start and length +- interrupts: description of the interrupt line + +Optional properties: + +- phys: list of phandles to PHY nodes. + This property is required if at least one of the ports are in + PHY mode i.e. OMAP_EHCI_PORT_MODE_PHY + +To specify the port mode, see +Documentation/devicetree/bindings/mfd/omap-usb-host.txt + +Example for OMAP4: + +usbhsehci: ehci@4a064c00 { + compatible = "ti,ehci-omap", "usb-ehci"; + reg = <0x4a064c00 0x400>; + interrupts = <0 77 0x4>; +}; + +&usbhsehci { + phys = <&hsusb1_phy 0 &hsusb3_phy>; +}; + diff --git a/Documentation/devicetree/bindings/usb/ohci-omap3.txt b/Documentation/devicetree/bindings/usb/ohci-omap3.txt new file mode 100644 index 00000000000..14ab42812a8 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-omap3.txt @@ -0,0 +1,15 @@ +OMAP HS USB OHCI controller (OMAP3 and later) + +Required properties: + +- compatible: should be "ti,ohci-omap3" +- reg: should contain one register range i.e. start and length +- interrupts: description of the interrupt line + +Example for OMAP4: + +usbhsohci: ohci@4a064800 { + compatible = "ti,ohci-omap3", "usb-ohci"; + reg = <0x4a064800 0x400>; + interrupts = <0 76 0x4>; +}; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 1ef0ce71f8f..662f0f1d231 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -8,10 +8,10 @@ OMAP MUSB GLUE and disconnect. - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - - num_eps : Specifies the number of endpoints. This is also a + - num-eps : Specifies the number of endpoints. This is also a MUSB configuration-specific setting. Should be set to "16" - - ram_bits : Specifies the ram address size. Should be set to "12" - - interface_type : This is a board specific setting to describe the type of + - ram-bits : Specifies the ram address size. Should be set to "12" + - interface-type : This is a board specific setting to describe the type of interface between the controller and the phy. It should be "0" or "1" specifying ULPI and UTMI respectively. - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" @@ -29,18 +29,46 @@ usb_otg_hs: usb_otg_hs@4a0ab000 { ti,hwmods = "usb_otg_hs"; ti,has-mailbox; multipoint = <1>; - num_eps = <16>; - ram_bits = <12>; + num-eps = <16>; + ram-bits = <12>; ctrl-module = <&omap_control_usb>; }; Board specific device node entry &usb_otg_hs { - interface_type = <1>; + interface-type = <1>; mode = <3>; power = <50>; }; +OMAP DWC3 GLUE + - compatible : Should be "ti,dwc3" + - ti,hwmods : Should be "usb_otg_ss" + - reg : Address and length of the register set for the device. + - interrupts : The irq number of this device that is used to interrupt the + MPU + - #address-cells, #size-cells : Must be present if the device has sub-nodes + - utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID. + It should be set to "1" for HW mode and "2" for SW mode. + - ranges: the child address space are mapped 1:1 onto the parent address space + +Sub-nodes: +The dwc3 core should be added as subnode to omap dwc3 glue. +- dwc3 : + The binding details of dwc3 can be found in: + Documentation/devicetree/bindings/usb/dwc3.txt + +omap_dwc3 { + compatible = "ti,dwc3"; + ti,hwmods = "usb_otg_ss"; + reg = <0x4a020000 0x1ff>; + interrupts = <0 93 4>; + #address-cells = <1>; + #size-cells = <1>; + utmi-mode = <2>; + ranges; +}; + OMAP CONTROL USB Required properties: diff --git a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt index 033194934f6..f575302e517 100644 --- a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt +++ b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt @@ -1,20 +1,25 @@ -* Samsung's usb phy transceiver +SAMSUNG USB-PHY controllers -The Samsung's phy transceiver is used for controlling usb phy for -s3c-hsotg as well as ehci-s5p and ohci-exynos usb controllers -across Samsung SOCs. +** Samsung's usb 2.0 phy transceiver + +The Samsung's usb 2.0 phy transceiver is used for controlling +usb 2.0 phy for s3c-hsotg as well as ehci-s5p and ohci-exynos +usb controllers across Samsung SOCs. TODO: Adding the PHY binding with controller(s) according to the under developement generic PHY driver. Required properties: Exynos4210: -- compatible : should be "samsung,exynos4210-usbphy" +- compatible : should be "samsung,exynos4210-usb2phy" - reg : base physical address of the phy registers and length of memory mapped region. +- clocks: Clock IDs array as required by the controller. +- clock-names: names of clock correseponding IDs clock property as requested + by the controller driver. Exynos5250: -- compatible : should be "samsung,exynos5250-usbphy" +- compatible : should be "samsung,exynos5250-usb2phy" - reg : base physical address of the phy registers and length of memory mapped region. @@ -44,12 +49,69 @@ Example: usbphy@125B0000 { #address-cells = <1>; #size-cells = <1>; - compatible = "samsung,exynos4210-usbphy"; + compatible = "samsung,exynos4210-usb2phy"; reg = <0x125B0000 0x100>; ranges; + clocks = <&clock 2>, <&clock 305>; + clock-names = "xusbxti", "otg"; + usbphy-sys { /* USB device and host PHY_CONTROL registers */ reg = <0x10020704 0x8>; }; }; + + +** Samsung's usb 3.0 phy transceiver + +Starting exynso5250, Samsung's SoC have usb 3.0 phy transceiver +which is used for controlling usb 3.0 phy for dwc3-exynos usb 3.0 +controllers across Samsung SOCs. + +Required properties: + +Exynos5250: +- compatible : should be "samsung,exynos5250-usb3phy" +- reg : base physical address of the phy registers and length of memory mapped + region. +- clocks: Clock IDs array as required by the controller. +- clock-names: names of clocks correseponding to IDs in the clock property + as requested by the controller driver. + +Optional properties: +- #address-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- #size-cells: should be '1' when usbphy node has a child node with 'reg' + property. +- ranges: allows valid translation between child's address space and parent's + address space. + +- The child node 'usbphy-sys' to the node 'usbphy' is for the system controller + interface for usb-phy. It should provide the following information required by + usb-phy controller to control phy. + - reg : base physical address of PHY_CONTROL registers. + The size of this register is the total sum of size of all PHY_CONTROL + registers that the SoC has. For example, the size will be + '0x4' in case we have only one PHY_CONTROL register (e.g. + OTHERS register in S3C64XX or USB_PHY_CONTROL register in S5PV210) + and, '0x8' in case we have two PHY_CONTROL registers (e.g. + USBDEVICE_PHY_CONTROL and USBHOST_PHY_CONTROL registers in exynos4x). + and so on. + +Example: + usbphy@12100000 { + compatible = "samsung,exynos5250-usb3phy"; + reg = <0x12100000 0x100>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&clock 1>, <&clock 286>; + clock-names = "ext_xtal", "usbdrd30"; + + usbphy-sys { + /* USB device and host PHY_CONTROL registers */ + reg = <0x10040704 0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt new file mode 100644 index 00000000000..d7e272671c7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt @@ -0,0 +1,34 @@ +USB NOP PHY + +Required properties: +- compatible: should be usb-nop-xceiv + +Optional properties: +- clocks: phandle to the PHY clock. Use as per Documentation/devicetree + /bindings/clock/clock-bindings.txt + This property is required if clock-frequency is specified. + +- clock-names: Should be "main_clk" + +- clock-frequency: the clock frequency (in Hz) that the PHY clock must + be configured to. + +- vcc-supply: phandle to the regulator that provides RESET to the PHY. + +- reset-supply: phandle to the regulator that provides power to the PHY. + +Example: + + hsusb1_phy { + compatible = "usb-nop-xceiv"; + clock-frequency = <19200000>; + clocks = <&osc 0>; + clock-names = "main_clk"; + vcc-supply = <&hsusb1_vcc_regulator>; + reset-supply = <&hsusb1_reset_regulator>; + }; + +hsusb1_phy is a NOP USB PHY device that gets its clock from an oscillator +and expects that clock to be configured to 19.2MHz by the NOP PHY driver. +hsusb1_vcc_regulator provides power to the PHY and hsusb1_reset_regulator +controls RESET. diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt index 3210540f8bd..237acab169d 100644 --- a/Documentation/ioctl/ioctl-number.txt +++ b/Documentation/ioctl/ioctl-number.txt @@ -131,6 +131,7 @@ Code Seq#(hex) Include File Comments 'H' 40-4F sound/hdspm.h conflict! 'H' 40-4F sound/hdsp.h conflict! 'H' 90 sound/usb/usx2y/usb_stream.h +'H' A0 uapi/linux/usb/cdc-wdm.h 'H' C0-F0 net/bluetooth/hci.h conflict! 'H' C0-DF net/bluetooth/hidp/hidp.h conflict! 'H' C0-DF net/bluetooth/cmtp/cmtp.h conflict! diff --git a/Documentation/usb/power-management.txt b/Documentation/usb/power-management.txt index 4204eb01fd3..1392b61d6eb 100644 --- a/Documentation/usb/power-management.txt +++ b/Documentation/usb/power-management.txt @@ -33,6 +33,10 @@ built with CONFIG_USB_SUSPEND enabled (which depends on CONFIG_PM_RUNTIME). System PM support is present only if the kernel was built with CONFIG_SUSPEND or CONFIG_HIBERNATION enabled. +(Starting with the 3.10 kernel release, dynamic PM support for USB is +present whenever the kernel was built with CONFIG_PM_RUNTIME enabled. +The CONFIG_USB_SUSPEND option has been eliminated.) + What is Remote Wakeup? ---------------------- @@ -206,10 +210,8 @@ initialized to 5. (The idle-delay values for already existing devices will not be affected.) Setting the initial default idle-delay to -1 will prevent any -autosuspend of any USB device. This is a simple alternative to -disabling CONFIG_USB_SUSPEND and rebuilding the kernel, and it has the -added benefit of allowing you to enable autosuspend for selected -devices. +autosuspend of any USB device. This has the benefit of allowing you +then to enable autosuspend for selected devices. Warnings |