diff options
Diffstat (limited to 'arch/arc/plat-arcfpga/platform.c')
| -rw-r--r-- | arch/arc/plat-arcfpga/platform.c | 164 |
1 files changed, 4 insertions, 160 deletions
diff --git a/arch/arc/plat-arcfpga/platform.c b/arch/arc/plat-arcfpga/platform.c index 19b76b61f44..1038949a99a 100644 --- a/arch/arc/plat-arcfpga/platform.c +++ b/arch/arc/plat-arcfpga/platform.c @@ -22,175 +22,22 @@ #include <plat/smp.h> #include <plat/irq.h> -/*-----------------------BVCI Latency Unit -----------------------------*/ - -#ifdef CONFIG_ARC_HAS_BVCI_LAT_UNIT - -int lat_cycles = CONFIG_BVCI_LAT_CYCLES; - -/* BVCI Bus Profiler: Latency Unit */ -static void __init setup_bvci_lat_unit(void) -{ -#define MAX_BVCI_UNITS 12 - - unsigned int i; - unsigned int *base = (unsigned int *)BVCI_LAT_UNIT_BASE; - const unsigned long units_req = CONFIG_BVCI_LAT_UNITS; - const unsigned int REG_UNIT = 21; - const unsigned int REG_VAL = 22; - - /* - * There are multiple Latency Units corresponding to the many - * interfaces of the system bus arbiter (both CPU side as well as - * the peripheral side). - * - * Unit 0 - System Arb and Mem Controller - adds latency to all - * memory trasactions - * Unit 1 - I$ and System Bus - * Unit 2 - D$ and System Bus - * .. - * Unit 12 - IDE Disk controller and System Bus - * - * The programmers model requires writing to lat_unit reg first - * and then the latency value (cycles) to lat_value reg - */ - - if (CONFIG_BVCI_LAT_UNITS == 0) { - writel(0, base + REG_UNIT); - writel(lat_cycles, base + REG_VAL); - pr_info("BVCI Latency for all Memory Transactions %d cycles\n", - lat_cycles); - } else { - for_each_set_bit(i, &units_req, MAX_BVCI_UNITS) { - writel(i + 1, base + REG_UNIT); /* loop is 0 based */ - writel(lat_cycles, base + REG_VAL); - pr_info("BVCI Latency for Unit[%d] = %d cycles\n", - (i + 1), lat_cycles); - } - } -} -#else -static void __init setup_bvci_lat_unit(void) -{ -} -#endif - -/*----------------------- Platform Devices -----------------------------*/ - -#if IS_ENABLED(CONFIG_SERIAL_ARC) -static unsigned long arc_uart_info[] = { - 0, /* uart->is_emulated (runtime @running_on_hw) */ - 0, /* uart->port.uartclk */ - 0, /* uart->baud */ - 0 -}; - -#if defined(CONFIG_SERIAL_ARC_CONSOLE) -/* - * static platform data - but only for early serial - * TBD: derive this from a special DT node - */ -static struct resource arc_uart0_res[] = { - { - .start = UART0_BASE, - .end = UART0_BASE + 0xFF, - .flags = IORESOURCE_MEM, - }, - { - .start = UART0_IRQ, - .end = UART0_IRQ, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device arc_uart0_dev = { - .name = "arc-uart", - .id = 0, - .num_resources = ARRAY_SIZE(arc_uart0_res), - .resource = arc_uart0_res, - .dev = { - .platform_data = &arc_uart_info, - }, -}; - -static struct platform_device *fpga_early_devs[] __initdata = { - &arc_uart0_dev, -}; -#endif /* CONFIG_SERIAL_ARC_CONSOLE */ - -static void arc_fpga_serial_init(void) -{ - /* To let driver workaround ISS bug: baudh Reg can't be set to 0 */ - arc_uart_info[0] = !running_on_hw; - - arc_uart_info[1] = arc_get_core_freq(); - - arc_uart_info[2] = CONFIG_ARC_SERIAL_BAUD; - -#if defined(CONFIG_SERIAL_ARC_CONSOLE) - early_platform_add_devices(fpga_early_devs, - ARRAY_SIZE(fpga_early_devs)); - - /* - * ARC console driver registers itself as an early platform driver - * of class "earlyprintk". - * Install it here, followed by probe of devices. - * The installation here doesn't require earlyprintk in command line - * To do so however, replace the lines below with - * parse_early_param(); - * early_platform_driver_probe("earlyprintk", 1, 1); - * ^^ - */ - early_platform_driver_register_all("earlyprintk"); - early_platform_driver_probe("earlyprintk", 1, 0); - - /* - * This is to make sure that arc uart would be preferred console - * despite one/more of following: - * -command line lacked "console=ttyARC0" or - * -CONFIG_VT_CONSOLE was enabled (for no reason whatsoever) - * Note that this needs to be done after above early console is reg, - * otherwise the early console never gets a chance to run. - */ - add_preferred_console("ttyARC", 0, "115200"); -#endif /* CONFIG_SERIAL_ARC_CONSOLE */ -} -#else /* !IS_ENABLED(CONFIG_SERIAL_ARC) */ -static void arc_fpga_serial_init(void) -{ -} -#endif - static void __init plat_fpga_early_init(void) { pr_info("[plat-arcfpga]: registering early dev resources\n"); - setup_bvci_lat_unit(); - - arc_fpga_serial_init(); - -#ifdef CONFIG_SMP +#ifdef CONFIG_ISS_SMP_EXTN iss_model_init_early_smp(); #endif } -static struct of_dev_auxdata plat_auxdata_lookup[] __initdata = { -#if IS_ENABLED(CONFIG_SERIAL_ARC) - OF_DEV_AUXDATA("snps,arc-uart", UART0_BASE, "arc-uart", arc_uart_info), -#endif - {} -}; - static void __init plat_fpga_populate_dev(void) { - pr_info("[plat-arcfpga]: registering device resources\n"); - /* * Traverses flattened DeviceTree - registering platform devices - * complete with their resources + * (if any) complete with their resources */ - of_platform_populate(NULL, of_default_bus_match_table, - plat_auxdata_lookup, NULL); + of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); } /*----------------------- Machine Descriptions ------------------------------ @@ -210,8 +57,7 @@ MACHINE_START(ANGEL4, "angel4") .dt_compat = aa4_compat, .init_early = plat_fpga_early_init, .init_machine = plat_fpga_populate_dev, - .init_irq = plat_fpga_init_IRQ, -#ifdef CONFIG_SMP +#ifdef CONFIG_ISS_SMP_EXTN .init_smp = iss_model_init_smp, #endif MACHINE_END @@ -225,7 +71,6 @@ MACHINE_START(ML509, "ml509") .dt_compat = ml509_compat, .init_early = plat_fpga_early_init, .init_machine = plat_fpga_populate_dev, - .init_irq = plat_fpga_init_IRQ, #ifdef CONFIG_SMP .init_smp = iss_model_init_smp, #endif @@ -240,5 +85,4 @@ MACHINE_START(NSIMOSCI, "nsimosci") .dt_compat = nsimosci_compat, .init_early = NULL, .init_machine = plat_fpga_populate_dev, - .init_irq = NULL, MACHINE_END |