diff options
Diffstat (limited to 'arch/arm/boot/dts/armada-370-rd.dts')
| -rw-r--r-- | arch/arm/boot/dts/armada-370-rd.dts | 47 |
1 files changed, 46 insertions, 1 deletions
diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts index 4169f4096ea..f57a8f84149 100644 --- a/arch/arm/boot/dts/armada-370-rd.dts +++ b/arch/arm/boot/dts/armada-370-rd.dts @@ -9,6 +9,15 @@ * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. + * + * Note: this Device Tree assumes that the bootloader has remapped the + * internal registers to 0xf1000000 (instead of the default + * 0xd0000000). The 0xf1000000 is the default used by the recent, + * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier + * boards were delivered with an older version of the bootloader that + * left internal registers mapped at 0xd0000000. If you are in this + * situation, you should either update your bootloader (preferred + * solution) or the below Device Tree should be adjusted. */ /dts-v1/; @@ -30,7 +39,7 @@ }; soc { - ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000 + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>; pcie-controller { @@ -50,6 +59,18 @@ }; internal-regs { + pinctrl { + fan_pins: fan-pins { + marvell,pins = "mpp8"; + marvell,function = "gpio"; + }; + + led_pins: led-pins { + marvell,pins = "mpp32"; + marvell,function = "gpio"; + }; + }; + serial@12000 { status = "okay"; }; @@ -59,6 +80,8 @@ }; mdio { + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; phy0: ethernet-phy@0 { reg = <0>; }; @@ -74,6 +97,8 @@ phy-mode = "sgmii"; }; ethernet@74000 { + pinctrl-0 = <&ge1_rgmii_pins>; + pinctrl-names = "default"; status = "okay"; phy = <&phy1>; phy-mode = "rgmii-id"; @@ -106,6 +131,26 @@ }; }; + gpio-fan { + compatible = "gpio-fan"; + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = <0 0 3000 1>; + pinctrl-0 = <&fan_pins>; + pinctrl-names = "default"; + }; + + gpio_leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + + sw_led { + label = "370rd:green:sw"; + gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + }; + nand@d0000 { status = "okay"; num-cs = <1>; |