diff options
Diffstat (limited to 'arch/arm/boot/dts/imx28-tx28.dts')
| -rw-r--r-- | arch/arm/boot/dts/imx28-tx28.dts | 703 |
1 files changed, 620 insertions, 83 deletions
diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts index 37be532f005..be5a0550d58 100644 --- a/arch/arm/boot/dts/imx28-tx28.dts +++ b/arch/arm/boot/dts/imx28-tx28.dts @@ -1,106 +1,139 @@ +/* + * Copyright 2012 Shawn Guo <shawn.guo@linaro.org> + * Copyright 2013 Lothar Waßmann <LW@KARO-electronics.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Ka-Ro electronics TX28 module"; compatible = "karo,tx28", "fsl,imx28"; + aliases { + can0 = &can0; + can1 = &can1; + display = &display; + ds1339 = &ds1339; + gpio5 = &gpio5; + lcdif = &lcdif; + lcdif_23bit_pins = &tx28_lcdif_23bit_pins; + lcdif_24bit_pins = &lcdif_24bit_pins_a; + stk5led = &user_led; + usbotg = &usb0; + }; + memory { - reg = <0x40000000 0x08000000>; - }; - - apb@80000000 { - apbh@80000000 { - ssp0: ssp@80010000 { - compatible = "fsl,imx28-mmc"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_4bit_pins_a - &mmc0_cd_cfg - &mmc0_sck_cfg>; - bus-width = <4>; - status = "okay"; - }; + reg = <0 0>; /* will be filled in by U-Boot */ + }; - pinctrl@80018000 { - pinctrl-names = "default"; - pinctrl-0 = <&hog_pins_a>; - - hog_pins_a: hog@0 { - reg = <0>; - fsl,pinmux-ids = < - 0x40a3 /* MX28_PAD_ENET0_RXD3__GPIO_4_10 */ - >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; - }; - - mac0_pins_gpio: mac0-gpio-mode@0 { - reg = <0>; - fsl,pinmux-ids = < - 0x4003 /* MX28_PAD_ENET0_MDC__GPIO_4_0 */ - 0x4013 /* MX28_PAD_ENET0_MDIO__GPIO_4_1 */ - 0x4023 /* MX28_PAD_ENET0_RX_EN__GPIO_4_2 */ - 0x4033 /* MX28_PAD_ENET0_RXD0__GPIO_4_3 */ - 0x4043 /* MX28_PAD_ENET0_RXD1__GPIO_4_4 */ - 0x4063 /* MX28_PAD_ENET0_TX_EN__GPIO_4_6 */ - 0x4073 /* MX28_PAD_ENET0_TXD0__GPIO_4_7 */ - 0x4083 /* MX28_PAD_ENET0_TXD1__GPIO_4_8 */ - 0x4103 /* MX28_PAD_ENET_CLK__GPIO_4_16 */ - >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; - }; - }; + onewire { + compatible = "w1-gpio"; + gpios = <&gpio2 7 0>; + status = "disabled"; + }; + + regulators { + compatible = "simple-bus"; + + reg_usb0_vbus: usb0_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb0_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio0 18 0>; + enable-active-high; }; - apbx@80040000 { - i2c0: i2c@80058000 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; + reg_usb1_vbus: usb1_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 27 0>; + enable-active-high; + }; - ds1339: rtc@68 { - compatible = "mxim,ds1339"; - reg = <0x68>; - }; - }; + reg_2p5v: 2p5v { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; - pwm: pwm@80064000 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_pins_a>; - status = "okay"; - }; + reg_3p3v: 3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; - duart: serial@80074000 { - pinctrl-names = "default"; - pinctrl-0 = <&duart_4pins_a>; - status = "okay"; - }; + reg_can_xcvr: can-xcvr { + compatible = "regulator-fixed"; + regulator-name = "CAN XCVR"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 0 0>; + enable-active-low; + pinctrl-names = "default"; + pinctrl-0 = <&tx28_flexcan_xcvr_pins>; + }; - auart1: serial@8006c000 { - pinctrl-names = "default"; - pinctrl-0 = <&auart1_pins_a>; - status = "okay"; - }; + reg_lcd: lcd-power { + compatible = "regulator-fixed"; + regulator-name = "LCD POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 31 0>; + enable-active-high; + }; + + reg_lcd_reset: lcd-reset { + compatible = "regulator-fixed"; + regulator-name = "LCD RESET"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 30 0>; + startup-delay-us = <300000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; }; }; - ahb@80080000 { - mac0: ethernet@800f0000 { - phy-mode = "rmii"; - pinctrl-names = "default", "gpio_mode"; - pinctrl-0 = <&mac0_pins_a>; - pinctrl-1 = <&mac0_pins_gpio>; - status = "okay"; + clocks { + #address-cells = <1>; + #size-cells = <0>; + mclk: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <27000000>; }; }; + sound { + compatible = "fsl,imx28-tx28-sgtl5000", + "fsl,mxs-audio-sgtl5000"; + model = "imx28-tx28-sgtl5000"; + saif-controllers = <&saif0 &saif1>; + audio-codec = <&sgtl5000>; + }; + leds { compatible = "gpio-leds"; - user { + user_led: user { label = "Heartbeat"; gpios = <&gpio4 10 0>; linux,default-trigger = "heartbeat"; @@ -109,8 +142,512 @@ backlight { compatible = "pwm-backlight"; - pwms = <&pwm 0 5000000>; - brightness-levels = <0 4 8 16 32 64 128 255>; - default-brightness-level = <6>; + pwms = <&pwm 0 500000>; + /* + * a silly way to create a 1:1 relationship between the + * PWM value and the actual duty cycle + */ + brightness-levels = < 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100>; + default-brightness-level = <50>; + }; + + matrix_keypad: matrix-keypad@0 { + compatible = "gpio-matrix-keypad"; + col-gpios = < + &gpio5 0 0 + &gpio5 1 0 + &gpio5 2 0 + &gpio5 3 0 + >; + row-gpios = < + &gpio5 4 0 + &gpio5 5 0 + &gpio5 6 0 + &gpio5 7 0 + >; + /* sample keymap */ + linux,keymap = < + 0x00000074 /* row 0, col 0, KEY_POWER */ + 0x00010052 /* row 0, col 1, KEY_KP0 */ + 0x0002004f /* row 0, col 2, KEY_KP1 */ + 0x00030050 /* row 0, col 3, KEY_KP2 */ + 0x01000051 /* row 1, col 0, KEY_KP3 */ + 0x0101004b /* row 1, col 1, KEY_KP4 */ + 0x0102004c /* row 1, col 2, KEY_KP5 */ + 0x0103004d /* row 1, col 3, KEY_KP6 */ + 0x02000047 /* row 2, col 0, KEY_KP7 */ + 0x02010048 /* row 2, col 1, KEY_KP8 */ + 0x02020049 /* row 2, col 2, KEY_KP9 */ + >; + gpio-activelow; + linux,wakeup; + debounce-delay-ms = <100>; + col-scan-delay-us = <5000>; + linux,no-autorepeat; + }; +}; + +/* 2nd TX-Std UART - (A)UART1 */ +&auart1 { + pinctrl-names = "default"; + pinctrl-0 = <&auart1_pins_a>; + status = "okay"; +}; + +/* 3rd TX-Std UART - (A)UART3 */ +&auart3 { + pinctrl-names = "default"; + pinctrl-0 = <&auart3_pins_a>; + status = "okay"; +}; + +&can0 { + pinctrl-names = "default"; + pinctrl-0 = <&can0_pins_a>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&can1_pins_a>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; +}; + +&digctl { + status = "okay"; +}; + +/* 1st TX-Std UART - (D)UART */ +&duart { + pinctrl-names = "default"; + pinctrl-0 = <&duart_4pins_a>; + status = "okay"; +}; + +&gpmi { + pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>; + nand-on-flash-bbt; + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + clock-frequency = <400000>; + status = "okay"; + + sgtl5000: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_2p5v>; + VDDIO-supply = <®_3p3v>; + clocks = <&mclk>; + }; + + gpio5: pca953x@20 { + compatible = "nxp,pca9554"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&tx28_pca9554_pins>; + interrupt-parent = <&gpio3>; + interrupts = <28 0>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + polytouch: edt-ft5x06@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&tx28_edt_ft5x06_pins>; + interrupt-parent = <&gpio2>; + interrupts = <5 0>; + reset-gpios = <&gpio2 6 1>; + wake-gpios = <&gpio4 9 0>; + }; + + touchscreen: tsc2007@48 { + compatible = "ti,tsc2007"; + reg = <0x48>; + pinctrl-names = "default"; + pinctrl-0 = <&tx28_tsc2007_pins>; + interrupt-parent = <&gpio3>; + interrupts = <20 0>; + pendown-gpio = <&gpio3 20 1>; + ti,x-plate-ohms = /bits/ 16 <660>; + }; + + ds1339: rtc@68 { + compatible = "mxim,ds1339"; + reg = <0x68>; + }; +}; + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_24bit_pins_a &lcdif_sync_pins_a &tx28_lcdif_ctrl_pins>; + lcd-supply = <®_lcd>; + display = <&display>; + status = "okay"; + + display: display@0 { + bits-per-pixel = <32>; + bus-width = <24>; + display-timings { + native-mode = <&timing5>; + timing0: timing0 { + panel-name = "VGA"; + clock-frequency = <25175000>; + hactive = <640>; + vactive = <480>; + hback-porch = <48>; + hsync-len = <96>; + hfront-porch = <16>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing1: timing1 { + panel-name = "ETV570"; + clock-frequency = <25175000>; + hactive = <640>; + vactive = <480>; + hback-porch = <114>; + hsync-len = <30>; + hfront-porch = <16>; + vback-porch = <32>; + vsync-len = <3>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing2: timing2 { + panel-name = "ET0350"; + clock-frequency = <6500000>; + hactive = <320>; + vactive = <240>; + hback-porch = <34>; + hsync-len = <34>; + hfront-porch = <20>; + vback-porch = <15>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing3: timing3 { + panel-name = "ET0430"; + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hback-porch = <2>; + hsync-len = <41>; + hfront-porch = <2>; + vback-porch = <2>; + vsync-len = <10>; + vfront-porch = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing4: timing4 { + panel-name = "ET0500", "ET0700"; + clock-frequency = <33260000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing5: timing5 { + panel-name = "ETQ570"; + clock-frequency = <6400000>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hsync-len = <30>; + hfront-porch = <30>; + vback-porch = <16>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; +}; + +&lradc { + fsl,lradc-touchscreen-wires = <4>; + status = "okay"; +}; + +&mac0 { + phy-mode = "rmii"; + pinctrl-names = "default", "gpio_mode"; + pinctrl-0 = <&mac0_pins_a>; + pinctrl-1 = <&tx28_mac0_pins_gpio>; + status = "okay"; +}; + +&mac1 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac1_pins_a>; + /* not enabled by default */ +}; + +&mxs_rtc { + status = "okay"; +}; + +&ocotp { + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>; + status = "okay"; +}; + +&pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_ENET0_RXD3__GPIO_4_10 /* module LED */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_edt_ft5x06_pins: tx28-edt-ft5x06-pins { + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA6__GPIO_2_6 /* RESET */ + MX28_PAD_SSP0_DATA5__GPIO_2_5 /* IRQ */ + MX28_PAD_ENET0_RXD2__GPIO_4_9 /* WAKE */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_flexcan_xcvr_pins: tx28-flexcan-xcvr-pins { + fsl,pinmux-ids = < + MX28_PAD_LCD_D00__GPIO_1_0 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_lcdif_23bit_pins: tx28-lcdif-23bit { + fsl,pinmux-ids = < + /* LCD_D00 may be used as Flexcan Transceiver Enable on STK5-V5 */ + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 + MX28_PAD_LCD_D18__LCD_D18 + MX28_PAD_LCD_D19__LCD_D19 + MX28_PAD_LCD_D20__LCD_D20 + MX28_PAD_LCD_D21__LCD_D21 + MX28_PAD_LCD_D22__LCD_D22 + MX28_PAD_LCD_D23__LCD_D23 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_lcdif_ctrl_pins: tx28-lcdif-ctrl { + fsl,pinmux-ids = < + MX28_PAD_LCD_ENABLE__GPIO_1_31 /* Enable */ + MX28_PAD_LCD_RESET__GPIO_3_30 /* Reset */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_mac0_pins_gpio: tx28-mac0-gpio-pins { + fsl,pinmux-ids = < + MX28_PAD_ENET0_MDC__GPIO_4_0 + MX28_PAD_ENET0_MDIO__GPIO_4_1 + MX28_PAD_ENET0_RX_EN__GPIO_4_2 + MX28_PAD_ENET0_RXD0__GPIO_4_3 + MX28_PAD_ENET0_RXD1__GPIO_4_4 + MX28_PAD_ENET0_TX_EN__GPIO_4_6 + MX28_PAD_ENET0_TXD0__GPIO_4_7 + MX28_PAD_ENET0_TXD1__GPIO_4_8 + MX28_PAD_ENET_CLK__GPIO_4_16 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_pca9554_pins: tx28-pca9554-pins { + fsl,pinmux-ids = < + MX28_PAD_PWM3__GPIO_3_28 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_tsc2007_pins: tx28-tsc2007-pins { + fsl,pinmux-ids = < + MX28_PAD_SAIF0_MCLK__GPIO_3_20 /* TSC2007 IRQ */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + + tx28_usbphy0_pins: tx28-usbphy0-pins { + fsl,pinmux-ids = < + MX28_PAD_GPMI_CE2N__GPIO_0_18 /* USBOTG_VBUSEN */ + MX28_PAD_GPMI_CE3N__GPIO_0_19 /* USBOTH_OC */ + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + tx28_usbphy1_pins: tx28-usbphy1-pins { + fsl,pinmux-ids = < + MX28_PAD_SPDIF__GPIO_3_27 /* USBH_VBUSEN */ + MX28_PAD_JTAG_RTCK__GPIO_4_20 /* USBH_OC */ + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; +}; + +&saif0 { + pinctrl-names = "default"; + pinctrl-0 = <&saif0_pins_b>; + fsl,saif-master; + status = "okay"; +}; + +&saif1 { + pinctrl-names = "default"; + pinctrl-0 = <&saif1_pins_a>; + status = "okay"; +}; + +&ssp0 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default", "special"; + pinctrl-0 = <&mmc0_4bit_pins_a + &mmc0_cd_cfg + &mmc0_sck_cfg>; + bus-width = <4>; + status = "okay"; +}; + +&ssp3 { + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins_a>; + clock-frequency = <57600000>; + status = "okay"; + + spidev0: spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <57600000>; + }; + + spidev1: spi@1 { + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <57600000>; }; }; + +&usb0 { + vbus-supply = <®_usb0_vbus>; + disable-over-current; + dr_mode = "peripheral"; + status = "okay"; +}; + +&usb1 { + vbus-supply = <®_usb1_vbus>; + disable-over-current; + dr_mode = "host"; + status = "okay"; +}; + +&usbphy0 { + pinctrl-names = "default"; + pinctrl-0 = <&tx28_usbphy0_pins>; + phy_type = "utmi"; + status = "okay"; +}; + +&usbphy1 { + pinctrl-names = "default"; + pinctrl-0 = <&tx28_usbphy1_pins>; + phy_type = "utmi"; + status = "okay"; +}; |