diff options
Diffstat (limited to 'arch/arm/boot/dts/imx6qdl-gw51xx.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/imx6qdl-gw51xx.dtsi | 374 |
1 files changed, 374 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi new file mode 100644 index 00000000000..98a422153ce --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi @@ -0,0 +1,374 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/ { + /* these are used by bootloader for disabling nodes */ + aliases { + can0 = &can1; + ethernet0 = &fec; + led0 = &led0; + led1 = &led1; + nand = &gpmi; + usb0 = &usbh1; + usb1 = &usbotg; + }; + + chosen { + bootargs = "console=ttymxc1,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led0: user1 { + label = "user1"; + gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */ + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led1: user2 { + label = "user2"; + gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */ + default-state = "off"; + }; + }; + + memory { + reg = <0x10000000 0x20000000>; + }; + + pps { + compatible = "pps-gpio"; + gpios = <&gpio1 26 0>; + status = "okay"; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3p3v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_5p0v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "5P0V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 30 0>; + status = "okay"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + eeprom1: eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom2: eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom3: eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom4: eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; + + gpio: pca9555@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + hwmon: gsc@29 { + compatible = "gw,gsp"; + reg = <0x29>; + }; + + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic: ltc3676@3c { + compatible = "ltc,ltc3676"; + reg = <0x3c>; + + regulators { + sw1_reg: ltc3676__sw1 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: ltc3676__sw2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: ltc3676__sw3 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: ltc3676__sw4 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ltc3676__ldo2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: ltc3676__ldo4 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + videoin: adv7180@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6qdl-gw51xx { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x80000000 /* MEZZ_DIO0 */ + MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x80000000 /* MEZZ_DIO1 */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000 /* OTG_PWR_EN */ + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x80000000 /* GPS_PPS */ + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* PHY Reset */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x80000000 /* PCIE_RST# */ + MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x80000000 /* user1 led */ + MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x80000000 /* user2 led */ + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + }; +}; + +&pcie { + reset-gpio = <&gpio1 0 0>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usbh1 { + status = "okay"; +}; |