1 files changed, 0 insertions, 354 deletions
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
deleted file mode 100644
index bf8a946b4cd..00000000000
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ /dev/null
@@ -1,354 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-sam9260ek.c
- *
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2006 Atmel
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/at73c213.h>
-#include <linux/clk.h>
-#include <linux/platform_data/at24.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * Audio
- */
-static struct at73c213_board_info at73c213_data = {
-	.ssc_id		= 0,
-	.shortname	= "AT91SAM9260-EK external DAC",
-};
-
-#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
-static void __init at73c213_set_clk(struct at73c213_board_info *info)
-{
-	struct clk *pck0;
-	struct clk *plla;
-
-	pck0 = clk_get(NULL, "pck0");
-	plla = clk_get(NULL, "plla");
-
-	/* AT73C213 MCK Clock */
-	at91_set_B_periph(AT91_PIN_PC1, 0);	/* PCK0 */
-
-	clk_set_parent(pck0, plla);
-	clk_put(plla);
-
-	info->dac_clk = pck0;
-}
-#else
-static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
-#endif
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-	{	/* DataFlash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-#endif
-#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
-	{	/* AT73C213 DAC */
-		.modalias	= "at73c213",
-		.chip_select	= 0,
-		.max_speed_hz	= 10 * 1000 * 1000,
-		.bus_num	= 1,
-		.mode		= SPI_MODE_1,
-		.platform_data	= &at73c213_data,
-	},
-#endif
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA7,
-	.is_rmii	= 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name	= "Partition 1",
-		.offset	= 0,
-		.size	= SZ_256K,
-	},
-	{
-		.name	= "Partition 2",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.on_flash_bbt	= 1,
-	.parts		= ek_nand_partition,
-	.num_parts	= ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	ek_nand_data.bus_width_16 = board_have_nand_16bit();
-	/* setup bus-width (8 or 16) */
-	if (ek_nand_data.bus_width_16)
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata ek_mci0_data = {
-	.slot[1] = {
-		.bus_width	= 4,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
-	{	/* "bottom" led, green, userled1 to be defined */
-		.name			= "ds5",
-		.gpio			= AT91_PIN_PA6,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* "power" led, yellow */
-		.name			= "ds1",
-		.gpio			= AT91_PIN_PA9,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-/*
- * I2C devices
- */
-static struct at24_platform_data at24c512 = {
-	.byte_len	= SZ_512K / 8,
-	.page_size	= 128,
-	.flags		= AT24_FLAG_ADDR16,
-};
-
-static struct i2c_board_info __initdata ek_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c512", 0x50),
-		.platform_data = &at24c512,
-	},
-	/* more devices can be added using expansion connectors */
-};
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PA30,
-		.code		= BTN_3,
-		.desc		= "Button 3",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PA31,
-		.code		= BTN_4,
-		.desc		= "Button 4",
-		.active_low	= 1,
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
-	.buttons	= ek_buttons,
-	.nbuttons	= ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_button_data,
-	}
-};
-
-static void __init ek_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PA30, 1);	/* btn3 */
-	at91_set_deglitch(AT91_PIN_PA30, 1);
-	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* btn4 */
-	at91_set_deglitch(AT91_PIN_PA31, 1);
-
-	platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-
-static void __init ek_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* NAND */
-	ek_add_device_nand();
-	/* Ethernet */
-	at91_add_device_eth(&ek_macb_data);
-	/* MMC */
-	at91_add_device_mci(0, &ek_mci0_data);
-	/* I2C */
-	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
-	/* SSC (to AT73C213) */
-	at73c213_set_clk(&at73c213_data);
-	at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-	/* Push Buttons */
-	ek_add_device_buttons();
-}
-
-MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK")
-	/* Maintainer: Atmel */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END