diff options
Diffstat (limited to 'arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c')
| -rw-r--r-- | arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c | 284 |
1 files changed, 284 insertions, 0 deletions
diff --git a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c new file mode 100644 index 00000000000..a4102d72cc9 --- /dev/null +++ b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c @@ -0,0 +1,284 @@ +/* + * Copyright (C) 2005 SAN People + * Copyright (C) 2008 Atmel + * Copyright (C) 2009 Rob Emanuele + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/spi/at73c213.h> +#include <linux/clk.h> + +#include <mach/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <mach/board.h> +#include <mach/gpio.h> +#include <mach/at91sam9_smc.h> + +#include "sam9_smc.h" +#include "generic.h" + + +static void __init ek_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9260_initialize(18432000); + + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init ek_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata ek_usbh_data = { + .ports = 2, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata ek_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + + +/* + * SPI devices. + */ +static struct spi_board_info ek_spi_devices[] = { +#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 1, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) + { /* DataFlash card */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#endif +#endif +}; + + +/* + * MACB Ethernet device + */ +static struct at91_eth_data __initdata ek_macb_data = { + .phy_irq_pin = AT91_PIN_PB0, + .is_rmii = 1, +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Bootstrap", + .offset = 0, + .size = 4 * SZ_1M, + }, + { + .name = "Partition 1", + .offset = MTDPART_OFS_NXTBLK, + .size = 60 * SZ_1M, + }, + { + .name = "Partition 2", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +/* det_pin is not connected */ +static struct atmel_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, + .rdy_pin = AT91_PIN_PC13, + .enable_pin = AT91_PIN_PC14, + .partition_info = nand_partitions, +#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) + .bus_width_16 = 1, +#else + .bus_width_16 = 0, +#endif +}; + +static struct sam9_smc_config __initdata ek_nand_smc_config = { + .ncs_read_setup = 0, + .nrd_setup = 2, + .ncs_write_setup = 0, + .nwe_setup = 2, + + .ncs_read_pulse = 4, + .nrd_pulse = 4, + .ncs_write_pulse = 4, + .nwe_pulse = 4, + + .read_cycle = 7, + .write_cycle = 7, + + .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, + .tdf_cycles = 3, +}; + +static void __init ek_add_device_nand(void) +{ + /* setup bus-width (8 or 16) */ + if (ek_nand_data.bus_width_16) + ek_nand_smc_config.mode |= AT91_SMC_DBW_16; + else + ek_nand_smc_config.mode |= AT91_SMC_DBW_8; + + /* configure chip-select 3 (NAND) */ + sam9_smc_configure(3, &ek_nand_smc_config); + + at91_add_device_nand(&ek_nand_data); +} + + +/* + * MCI (SD/MMC) + * wp_pin is not connected + */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mmc_data = { + .slot[0] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC2, + .wp_pin = -ENODEV, + }, + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + .wp_pin = -ENODEV, + }, + +}; +#else +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 1, /* Only one slot so use slot B */ + .wire4 = 1, + .det_pin = AT91_PIN_PC9, +}; +#endif + +/* + * LEDs + */ +static struct gpio_led ek_leds[] = { + { /* "bottom" led, green, userled1 to be defined */ + .name = "ds5", + .gpio = AT91_PIN_PB8, + .active_low = 1, + .default_trigger = "none", + }, + { /* "power" led, yellow */ + .name = "ds1", + .gpio = AT91_PIN_PB9, + .default_trigger = "heartbeat", + } +}; + +static struct i2c_board_info __initdata ek_i2c_devices[] = { + { + I2C_BOARD_INFO("24c512", 0x50), + }, +}; + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&ek_usbh_data); + /* USB Device */ + at91_add_device_udc(&ek_udc_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* NAND */ + ek_add_device_nand(); + /* Ethernet */ + at91_add_device_eth(&ek_macb_data); + /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + at91_add_device_mci(0, &ek_mmc_data); +#else + at91_add_device_mmc(0, &ek_mmc_data); +#endif + /* I2C */ + at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); + /* LEDs */ + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + /* PCK0 provides MCLK to the WM8731 */ + at91_set_B_periph(AT91_PIN_PC1, 0); + /* SSC (for WM8731) */ + at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); +} + +MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod") + /* Maintainer: Rob Emanuele */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END |